The ADC driver always programs all possible ADC values and discards
them except for the value IIO asked for. On the am335x-evm the driver
programs four values and it takes 500us to gather them. Reducing the number
of conversations down to the (required) one also reduces the busy loop down
to 125us.
This leads to another error, namely the FIFOCOUNT register is sometimes
(like one out of 10 attempts) not updated in time leading to EBUSY.
The next read has the FIFOCOUNT register updated.
Checking for the ADCSTAT register for being idle isn't a good choice either.
The problem is that if TSC is used at the same time, the HW completes the
conversation for ADC *and* before the driver noticed it, the HW begins to
perform a TSC conversation and so the driver never seen the HW idle. The
next time we would have two values in the FIFO but since the driver reads
everything we always see the current one.
So instead of polling for the IDLE bit in ADCStatus register, we should
check the FIFOCOUNT register. It should be one instead of zero because we
request one value.
This change in turn leads to another error. Sometimes if TSC & ADC are
used together the TSC starts generating interrupts even if nobody
actually touched the touchscreen. The interrupts seem valid because TSC's
FIFO is filled with values for each channel of the TSC. This condition stops
after a few ADC reads but will occur again. Not good.
On top of this (even without the changes I just mentioned) there is a ADC
& TSC lockup condition which was reported to me by Jeff Lance including the
following test case:
A busy loop of "cat /sys/bus/iio/devices/iio\:device0/in_voltage4_raw"
and a mug on touch screen. With this setup, the hardware will lockup after
something between 20 minutes and it could take up to a couple of hours.
During that lockup, the ADCSTAT register says 0x30 (or 0x70) which means
STEP_ID = IDLE and FSM_BUSY = yes. That means the hardware says that it is
idle and busy at the same time which is an invalid condition.
For all this reasons I decided to rework this TSC/ADC part and add a
handshake / synchronization here:
First the ADC signals that it needs the HW and writes a 0 mask into the
SE register. The HW (if active) will complete the current conversation
and become idle. The TSC driver will gather the values from the FIFO
(woken up by an interrupt) and won't "enable" another conversation.
Instead it will wake up the ADC driver which is already waiting. The ADC
driver will start "its" conversation and once it is done, it will
enable the TSC steps so the TSC will work again.
After this rework I haven't observed the lockup so far. Plus the busy
loop has been reduced from 500us to 125us.
The continues-read mode remains unchanged.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The purpose of reg_se_cache has been defeated. It should avoid the
read-back of the register to avoid the latency and the fact that the
bits are reset to 0 after the individual conversation took place.
The reason why this is required like this to work, is that read-back of
the register removes the bits of the ADC so they do not start another
conversation after the register is re-written from the TSC side for the
update.
To avoid the not required read-back I introduce a "set once" variant which
does not update the cache mask. After the conversation completes, the
bit is removed from the SE register anyway and we don't plan a new
conversation "any time soon". The current set function is renamed to
set_cache to distinguish the two operations.
This is a small preparation for a larger sync-rework.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the "recent" changes, am335x_tsc_se_update() has no longer any
users outside of this file so make it local.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
BBCH_BBCHEN_MASK is equivalent to TPS65910_SUPPLY_STATE_ENABLED.
So all regulators have the same enable_mask setting.
BBCH_BBCHEN_MASK and BBCH_BBCHEN_SHIFT are not used now, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
tps65910 has a backup battery charger with a configurable voltage. This
patch adds a regulator for the backup battery.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove sec_reg* helpers as they are not used anymore. These helpers were
error-prone as they mixed u8 with unsigned int and they changed order of
some of parameters (val and mask in sec_reg_update()).
Also the helpers didn't give any way of useful abstraction as they just
called corresponding regmap function.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add symbols for hard-coded values of BUCK_RAMP field in DVS_RAMP
register. This simplifies a little the code as register update is called
only once.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Replace hard-coded value for mask used in BUCKX_CTRL registers (for
BUCKX_EN field) with a symbol. This also removes two local variables.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add mx6 hdmi transmitter support.
Original work has been done by Sascha Hauer and Tony Prisk.
Special thanks to Russell King for his carefully review, many bug fixes and
testing of the mx6 HDMI driver.
Tested on the following boards:
- mx6q sabresd
- mx6dl sabresd
- mx6solo wandboard
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull trivial tree updates from Jiri Kosina:
"Usual earth-shaking, news-breaking, rocket science pile from
trivial.git"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: usb: Fix typo in Documentation/usb/gadget_configs.txt
doc: add missing files to timers/00-INDEX
timekeeping: Fix some trivial typos in comments
mm: Fix some trivial typos in comments
irq: Fix some trivial typos in comments
NUMA: fix typos in Kconfig help text
mm: update 00-INDEX
doc: Documentation/DMA-attributes.txt fix typo
DRM: comment: `halve' -> `half'
Docs: Kconfig: `devlopers' -> `developers'
doc: typo on word accounting in kprobes.c in mutliple architectures
treewide: fix "usefull" typo
treewide: fix "distingush" typo
mm/Kconfig: Grammar s/an/a/
kexec: Typo s/the/then/
Documentation/kvm: Update cpuid documentation for steal time and pv eoi
treewide: Fix common typo in "identify"
__page_to_pfn: Fix typo in comment
Correct some typos for word frequency
clk: fixed-factor: Fix a trivial typo
...
Pull MFD updates from Samuel Ortiz:
"For the 3.13 merge window we have a couple of new drivers for the AMS
AS3722 PMIC and for STMicroelectronics STw481x PMIC.
Although this is a smaller update than usual, we also have:
- Device tree support for the max77693 driver
- linux/of.h inclusion for all DT compatible MFD drivers, to avoid
build breakage in the future
- Support for Intel Wildcat Point-LP PCH through the lpc_ich driver
- A small arizona update for new wm5110 DSP registers and a few fixes
- A small palmas update as well, including an of_device table
addition and a few minor fixes
- Two small mfd-core changes, one including a memory leak fix for
when mfd_add_device() fails
- Our usual round of minor cleanups and janitorial fixes"
* tag 'mfd-3.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (63 commits)
Documentation: mfd: Update s2mps11.txt
mfd: pm8921: Potential NULL dereference in pm8921_remove()
mfd: Fix memory leak in mfd_add_devices()
mfd: Stop setting refcounting pointers in original mfd_cell arrays
mfd: wm5110: Enable micd clamp functionality
mfd: lpc_ich: Add Device IDs for Intel Wildcat Point-LP PCH
mfd: max77693: Fix up bug of wrong interrupt number
mfd: as3722: Don't export the regmap config
mfd: twl6040: Remove obsolete cleanup for i2c clientdata
mfd: tps65910: Remove warning during dt node parsing
mfd: lpc_sch: Ignore resource conflicts when adding mfd cells
mfd: ti_am335x_tscadc: Avoid possible deadlock of reg_lock
mfd: syscon: Return -ENOSYS if CONFIG_MFD_SYSCON is not enabled
mfd: Add support for ams AS3722 PMIC
mfd: max77693: Include linux/of.h header
mfd: tc3589x: Detect the precise version
mfd: omap-usb: prepare/unprepare clock while enable/disable
mfd: max77686: Include linux/of.h header
mfd: max8907: Include linux/of.h header
mfd: max8997: Include linux/of.h header
...
Pull sound updates from Takashi Iwai:
"There are no too intrusive changes in this update batch. The biggest
LOC is found in the new DICE driver, and other small changes are
scattered over the whole sound subtree (which is a common pattern).
Below are highlights:
- ALSA core:
* Memory allocation support with genpool
* Fix blocking in drain ioctl of compress_offload
- HD-audio:
* Improved AMD HDMI supports
* Intel HDMI detection improvements
* thinkpad_acpi mute-key integration
* New PCI ID, New ALC255,285,293 codecs, CX20952
- USB-audio:
* New buffer size management
* Clean up endpoint handling codes
- ASoC:
* Further work on the dmaengine helpers, including support for
configuring the parameters for DMA by reading the capabilities of
the DMA controller which removes some guesswork and magic numbers
from drivers.
* A refresh of the documentation.
* Conversions of many drivers to direct regmap API usage in order
to allow the ASoC level register I/O code to be removed, this
will hopefully be completed by v3.14.
* Support for using async register I/O in DAPM, reducing the time
taken to implement power transitions on systems that support it.
- Firewire: DICE driver
- Lots of small fixes for bugs reported by Coverity"
* tag 'sound-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (382 commits)
ALSA: hda/realtek - Add new codec ALC255/ALC3234 UAJ supported
ALSA: hda - Apply MacBook fixups for CS4208 correctly
ASoC: fsl: imx-wm8962: remove an unneeded check
ASoC: fsl: imx-pcm-fiq: Remove unused 'runtime' variable
ALSA: hda/realtek - Make fixup regs persist after resume
ALSA: hda_intel: ratelimit "spurious response" message
ASoC: generic-dmaengine-pcm: Use SNDRV_DMA_TYPE_DEV_IRAM as default
ASoC: dapm: Use WARN_ON() instead of BUG_ON()
ASoC: wm_adsp: Fix BUG_ON() and WARN_ON() usages
ASoC: Replace BUG() with WARN()
ASoC: wm_hubs: Replace BUG() with WARN()
ASoC: wm8996: Replace BUG() with WARN()
ASoC: wm8962: Replace BUG() with WARN()
ASoC: wm8958: Replace BUG() with WARN()
ASoC: wm8904: Replace BUG() with WARN()
ASoC: wm8900: Replace BUG() with WARN()
ASoC: wm8350: Replace BUG() with WARN()
ASoC: txx9: Use WARN_ON() instead of BUG_ON()
ASoC: sh: Use WARN_ON() instead of BUG_ON()
ASoC: rcar: Use WARN_ON() instead of BUG_ON()
...
Pull regulator updates from Mark Brown:
"Lots of driver updates here plus some nice new core features, the main
one being the first:
- Enable support for providing a dummy regulator when we know that
one must exist for the device to be functional. This makes it much
easier to add regulator support to drivers since we don't require
that the machine integration for all systems using the device be
updated to provide regulators.
- Substantial reduction in the amount of busy waiting done while
waiting for enables to complete.
- Allow MFDs to distribute regulator supplies to child devices so we
don't have to expose the internal structure of MFDs outside of the
driver.
- Managed registeration for regulators"
* tag 'regulator-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (113 commits)
regulator: s5m8767: Modify parsing method of the voltage table of buck2/3/4
regulator: s5m8767: Modify parse_dt function to parse data related to ramp
regulator: da9052: Revert se apply_[reg|bit] with regmap based voltage_sel operations
mfd: arizona: Specify supply mappings for Arizona CODECs
mfd: Allow mapping regulator supplies to MFD device from children
regulator: core: Add ability to create a lookup alias for supply
regulator: tps65910: Fix checkpatch issue
regulator: tps65023: Fix checkpatch issue
regulator: tps6105x: Fix checkpatch issue
regulator: mc13783: Fix checkpatch issue
regulator: max8997: Fix checkpatch issue
regulator: lp3971: Fix checkpatch issue
regulator: fixed: Fix checkpatch issue
regulator: anatop: Fix checkpatch issue
regulator: Add REGULATOR_LINEAR_RANGE macro
regulator: Remove max_uV from struct regulator_linear_range
regulator: ti-abb: Fix operator precedence typo
regulator: tps65910: get regulators node from parent node only
regulator: tps6586x: get regulators node from parent node only
regulator: tps65090: get regulators node from parent node only
...
Commit 1e29af62f2 ("mfd: Add refcounting
support to mfd_cells") had to drop the "const" keyword on the "cell"
parameter of mfd_add_devices(), as it added the refcounting pointers
to the objects of the passed mfd_cell array itself.
However, the mfd core code operates on copies of the mfd_cell objects,
so there's no need to modify the originally passed objects.
Hence, move the setting of the refcounting pointers from mfd_add_devices()
to mfd_platform_add_cell(), where the copy of the mfd_cell objects is made.
mfd_clone_cell() can just pass (a copy of) the original usage_count
pointer.
This allows to make the "cell" parameter of mfd_add_devices() "const"
again, and avoids future race conditions when registering multiple
instances of the same device in parallel.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Pull ARM SoC DT updates from Olof Johansson:
"Most of this branch consists of updates, additions and general churn
of the device tree source files in the kernel (arch/arm/boot/dts).
Besides that, there are a few things to point out:
- Lots of platform conversion on OMAP2+, with removal of old board
files for various platforms.
- Final conversion of a bunch of ux500 (ST-Ericsson) platforms as
well
- Some updates to pinctrl and other subsystems. Most of these are
for DT-enablement of the various platforms and acks have been
collected"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (385 commits)
ARM: dts: bcm11351: Use GIC/IRQ defines for sdio interrupts
ARM: dts: bcm: Add missing UARTs for bcm11351 (bcm281xx)
ARM: dts: bcm281xx: Add card detect GPIO
ARM: dts: rename ARCH_BCM to ARCH_BCM_MOBILE (dt)
ARM: bcm281xx: Add device node for the GPIO controller
ARM: mvebu: Add Netgear ReadyNAS 104 board
ARM: tegra: fix Tegra114 IOMMU register address
ARM: kirkwood: add support for OpenBlocks A7 platform
ARM: dts: omap4-panda: add DPI pinmuxing
ARM: dts: AM33xx: Add RNG node
ARM: dts: AM33XX: Add hwspinlock node
ARM: dts: OMAP5: Add hwspinlock node
ARM: dts: OMAP4: Add hwspinlock node
ARM: dts: use 'status' property for PCIe nodes
ARM: dts: sirf: add missed address-cells and size-cells for prima2 I2C
ARM: dts: sirf: add missed cell, cs and dma channel for SPI nodes
ARM: dts: sirf: add missed graphics2d iobg in atlas6 dts
ARM: dts: sirf: add missed chhifbg node in prima2 and atlas6 dts
ARM: dts: sirf: add missed memcontrol-monitor node in prima2 and atlas6 dts
ARM: mvebu: Add the core-divider clock to Armada 370/XP
...
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Among the things new for this release
are:
- More support for the AM33xx platforms from TI
- Tegra 124 support, and some updates to older tegra families as well
- imx cleanups and updates across the board
- A rename of Broadcom's Mobile platforms which were introduced as
ARCH_BCM, and turned out to be too broad a name. New name is
ARCH_BCM_MOBILE.
- A whole bunch of updates and fixes for integrator, making the
platform code more modern and switches over to DT-only booting.
- Support for two new Renesas shmobile chipsets. Next up for them is
more work on consolidation instead of introduction of new
non-multiplatform SoCs, we're all looking forward to that!
- Misc cleanups for older Samsung platforms, some Allwinner updates,
etc"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (159 commits)
ARM: bcm281xx: Add ARCH_BCM_MOBILE to bcm config
ARM: bcm_defconfig: Run "make savedefconfig"
ARM: bcm281xx: Add ARCH Timers to config
rename ARCH_BCM to ARCH_BCM_MOBILE (mach-bcm)
ARM: vexpress: Enable platform-specific options in defconfig
ARM: vexpress: Make defconfig work again
ARM: sunxi: remove .init_time hooks
ARM: imx: enable suspend for imx6sl
ARM: imx: ensure dsm_request signal is not asserted when setting LPM
ARM: imx6q: call WB and RBC configuration from imx6q_pm_enter()
ARM: imx6q: move low-power code out of clock driver
ARM: imx: drop extern with function prototypes in common.h
ARM: imx: reset core along with enable/disable operation
ARM: imx: do not return from imx_cpu_die() call
ARM: imx_v6_v7_defconfig: Select CONFIG_PROVE_LOCKING
ARM: imx_v6_v7_defconfig: Enable LEDS_GPIO related options
ARM: mxs_defconfig: Turn off CONFIG_DEBUG_GPIO
ARM: imx: replace imx6q_restart() with mxc_restart()
ARM: mach-imx: mm-imx5: Retrieve iomuxc base address from dt
ARM: mach-imx: mm-imx5: Retrieve tzic base address from dt
...
Some platforms may not define CONFIG_MFD_SYSCON (or haven't syscon),
it can fix build error for these platforms.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ams AS3722 is a compact system PMU suitable for mobile phones,
tablets etc. It has 4 DC/DC step-down regulators, 3 DC/DC step-down
controller, 11 LDOs, RTC, automatic battery, temperature and
over-current monitoring, 8 GPIOs, ADC and a watchdog.
Add MFD core driver for the AS3722 to support core functionality.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Florian Lobmaier <florian.lobmaier@ams.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The patch removes wakeup related code from the driver and plaftorm
data - it is already handled by i2c core using I2C_CLIENT_WAKE flag
from struct i2c_board_info. As a result MFD itself do not requires
platform data.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Move the workaround for double sending AUDIO_CODEC and AUDIO_DAC writes
into the SPI core, aiding refactoring to eliminate the ASoC custom I/O
functions and avoiding the extra writes for I2C.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The ADC clock divider needs to be restored on resume as the register content
is lost when the ADC is powered down
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This adds a driver for the STw481x PMICs found in the Nomadik
family of platforms. This one uses pure device tree probing.
Print some of the OTP registers on boot and register a regulator
MFD child.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We had specified the mask twice for FLL2_SYNC_BW change the first mask
definition in a bit definition to match the other fields.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In some platforms, specially Thinkpad series, rts5249 won't be
initialized properly. So we need adjust some phy parameters to
improve the compatibility issue.
It is a little different between simulation and real chip. We have
no idea about which configuration is better before tape-out. We set
default settings according to simulation, but need to tune these
parameters after getting the real chip.
I can't explain every change in detail here. The below information is
just a rough description:
PHY_REG_REV: Disable internal clkreq_tx, enable rx_pwst
PHY_BPCR: No change, just turn the magic number to macro definitions
PHY_PCR: Change OOBS sensitivity, from 60mV to 90mV
PHY_RCR2: Control charge-pump current automatically
PHY_FLD4: Use TX cmu reference clock
PHY_RDR: Change RXDSEL from 30nF to 1.9nF
PHY_RCR1: Change the duration between adp_st and asserting cp_en from
0.32 us to 0.64us
PHY_FLD3: Adjust internal timers
PHY_TUNE: Fine tune the regulator12 output voltage
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The old timeout value was based on the assumption that the minimum values are
used for the open and sample delay and no averaging is done. In fact the ADC
and touchscreen driver both use an open delay of 152 cycles and averaging over
16 samples. This patch adjusts the timeout value accordingly
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the conversion to regmap-irq irq_lock has been unused.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Since the register I/O functions are all simple wrappers for the regmap
equivalents inline them to provide a small code size saving and an example
of good practice.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
DA9053 (up to revision bc) can corrupt internal registers when multi-write
mode is enabled and power is removed or during shutdown.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Occasionally, it is useful to map supplies from a child device onto the
MFD device. A typical usecase for this would be if the MFD device is
represented as a single node in device tree. All supplies will be
defined in device tree as existing on the MFD device. When a child
depends on frameworks which might have no knowledge of MFD to lookup
supplies on its behalf the supply will not be found.
This patch adds a list of supplies that should be looked up on the
parent rather than the child as part of the mfd_cell structure.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add imx6sl iomux-gpr register field define in "imx6q-iomuxc-gpr.h" header
file, which is not fully define all iomux-gpr registers and fields, only
add fec related macro define.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Correct common misspelling of "identify" as "indentify" throughout
the kernel
Signed-off-by: Maxime Jayat <maxime@artisandeveloppeur.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
These are required to request DBx500 PRCMU clocks from Device Tree. The
numbers used are taken directly from the Hardware Specification document.
We're moving them from the DBx500 PRCMU include file into the DT include
directory and referencing them from the former via a #include.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Move the workaround for double sending AUDIO_CODEC and AUDIO_DAC writes
into the SPI core, aiding refactoring to eliminate the ASoC custom I/O
functions and avoiding the extra writes for I2C.
Signed-off-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Jonathan writes:
First round of new drivers, functionality and cleanups for IIO in the 3.13 cycle
A number of new drivers and some new functionality + a lot of cleanups
all over IIO.
New Core Elements
1) New INT_TIME info_mask element for integration time, which may have
different effects on measurement noise and similar, than an amplifier
and hence is different from existing SCALE. Already existed in some
drivers as a custom attribute.
2) Introduce a iio_push_buffers_with_timestamp helper to cover the common
case of filling the last 64 bits of data to be passed to the buffer with
a timestamp. Applied to lots of drivers. Cuts down on repeated code and
moves a slightly fiddly bit of logic into a single location.
3) Introduce info_mask_[shared_by_dir/shared_by_all] elements to allow support
of elements such as sampling_frequency which is typically shared by all
input channels on a device. This reduces code and makes these controls
available from in kernel consumers of IIO devices.
New drivers
1) MCP3422/3/4 ADC
2) TSL4531 ambient light sensor
3) TCS3472/5 color light sensor
4) GP2AP020A00F ambient light / proximity sensor
5) LPS001WP support added to ST pressure sensor driver.
New driver functionality
1) ti_am335x_adc Add buffered sampling support.
This device has a hardware fifo that is fed directly into an IIO kfifo
buffer based on a watershed interrupt. Note this will act as an example
of how to handle this increasingly common type of device.
The only previous example - sca3000 - take a less than optimal approach
which is largely why it is still in staging.
A couple of little cleanups for that new functionality followed later.
Core cleanups:
1) MAINTAINERS - Sachin actually brought my email address up to date because
I said I'd do it and never got around to it :)
2) Assign buffer list elements as single element lists to simplify the
iio_buffer_is_active logic.
3) wake_up_interruptible_poll instead of wake_up_interruptible to only wake
up threads waiting for poll notifications.
4) Add O_CLOEXEC flag to anon_inode_get_fd call for IIO event interface.
5) Change iio_push_to_buffers to take a void * pointer so as to avoid some
annoying and unnecessary type casts.
6) iio_compute_scan_bytes incorrectly took a long rather than unsigned long.
7) Various minor tidy ups.
Driver cleanups (in no particular order)
1) Another set of devm_ allocations patches from Sachin Kamat.
2) tsl2x7x - 0 to NULL cleanup.
3) hmc5843 - fix missing > in MODULE_AUTHOR
4) Set of strict_strto* to kstrto* conversions.
5) mxs-lradc - fix ordering of resource removal to match creation
6) mxs-lradc - add MODULE_ALIAS
7) adc7606 - drop a work pending test duplicated in core functions.
8) hmc5843 - devm_ allocation patch
9) Series of redundant breaks removed.
10) ad2s1200 - pr_err -> dev_err
11) adjd_s311 - use INT_TIME
12) ST sensors - large set of cleanups from Lee Jones and removed restriction
to using only triggers provided by the st_sensors themselves from
Dennis Ciocca.
13) dummy and tmp006 provide sampling_frequency via info_mask_shared_by_all.
14) tcs3472 - fix incorrect buffer size and wrong device pointer used in
suspend / resume functions.
15) max1363 - use defaults for buffer setup ops as provided by the triggered
buffer helpers as they are the same as were specified in max1363 driver.
16) Trivial tidy ups in a number of other drivers.
Previously the driver had only one-shot reading functionality.
This patch adds continuous sampling support to the driver.
Continuous sampling starts when buffer is enabled.
HW IRQ wakes worker thread that pushes samples to userspace.
Sampling stops when buffer is disabled by userspace.
Patil Rachna (TI) laid the ground work for ADC HW register access.
Russ Dill (TI) fixed bugs in the driver relevant to FIFOs and IRQs.
I fixed channel scanning so multiple ADC channels can be read
simultaneously and pushed to userspace.
Restructured the driver to fit IIO ABI.
And added INDIO_BUFFER_HARDWARE mode.
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
