This patch adds the 2500Base-X PHY mode support in the Marvell PPv2
driver. 2500Base-X is quite close to 1000Base-X and SGMII modes and uses
nearly the same code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 1000Base-X PHY mode support in the Marvell PPv2
driver. 1000Base-X is quite close the SGMII and uses nearly the same
code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the PPv2 driver to implement phylink helpers, and use phylink in
DT mode. The other mode supported is ACPI, which will need further work
in order to be entirely compatible with phylink.
The MAC and GoP configuration functions were completely moved to fit
into the phylink helpers. When a PHY is always present between the MAC
and the physical port, phylink only is used, but when this is not the
case (the MAC directly is connected to the physical port) the link IRQ
is used to detect changes in the link state and call phylink_mac_change.
The ACPI mode do not uses phylink as of now, and the changes shouldn't
impact its use.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cosmetic patch to align the ethtool functions to ops definitions. This
patch does not change in any way the driver's behaviour.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kalle Valo says:
====================
wireless-drivers-next patches for 4.18
The first pull request for 4.18. As usual new features and bug fixes
but nothing really special.
I also merged wireless-drivers due to an iwlwifi patch dependency.
Major changes:
iwlwifi
* implement Traffic Condition Monitor and use it for scan, BT coex and
to detect when the AP doesn't support UAPSD properly
* some more work for the 22000 family of devices;
* introduce AMSDU rate control offload
qtnfmac
* DFS offload support
rsi
* roaming enhancements
* increase max supported aggregation subframes
* don't advertise 5 GHz support if the device doesn't support it
brcmfmac
* add support for BCM4366E chipset
* add support for bcm43364 wireless chipset
ath10k
* enable temperature reads for QCA6174 and QCA9377
* add firmware memory dump support for QCA9984
* continue adding WCN3990 support via SNOC bus
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
As documented in Documentation/timers/timers-howto.txt,
replace msleep(1) with usleep_range().
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The early versions of am33xx devices, related to ES1.0 SoC revision
have errata limiting mq support. That's the same errata as
commit 7da1160002 ("drivers: net: cpsw: add am335x errata workarround for
interrutps")
AM33xx Errata [1] Advisory 1.0.9
http://www.ti.com/lit/er/sprz360f/sprz360f.pdf
After additional investigation were found that drivers w/a is
propagated on all AM33xx SoCs and on DM814x. But the errata exists
only for ES1.0 of AM33xx family, limiting mq support for revisions
after ES1.0. So, disable mq support only for related SoCs and use
separate polls for revisions allowing mq.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move initialization of statistics buffers from ibmvnic_init function
into ibmvnic_probe. In the current state, ibmvnic_init will be called
again during a device reset, resulting in the allocation of new
buffers without freeing the old ones.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not necessary to disable interrupt lines here during a reset
to handle a non-fatal firmware error. Move that call within the code
block that handles the other cases that do require interrupts to be
disabled and re-enabled.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the firmware map fails for whatever reason, remember to free
up the memory after.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set hw->mac.perm_addr in ixgbevf_set_mac() in order to avoid losing the
custom MAC on reset. This can happen in the following case:
>ip link set $vf address $mac
>ethtool -r $vf
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Do not validate the MAC address during a reset, unless the MAC was set on
the host. This way the VF will get a new MAC address every time it reloads.
Remove the "no MAC address assigned" message since it will get spammed on
reset and it doesn't help much as the MAC on the VF is randomly generated.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently, during device_shutdown() ixgbe holds rtnl_lock for the duration
of lengthy ixgbe_close_suspend(). On machines with multiple ixgbe cards
this lock prevents scaling if device_shutdown() function is multi-threaded.
It is not necessary to hold this lock during ixgbe_close_suspend()
as it is not held when ixgbe_close() is called also during shutdown but for
kexec case.
Signed-off-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since commit f7f37e7ff2 ("ixgbe: handle close/suspend race with
netif_device_detach/present") ixgbe_close_suspend is called, from
ixgbe_close, only if the device is present, i.e. if it isn't detached.
That exposed a situation where IRQs weren't freed if a PCI error
recovery system opts to remove the device. For such case the pci channel
state is set to pci_channel_io_perm_failure and ixgbe_io_error_detected
was returning PCI_ERS_RESULT_DISCONNECT before calling
ixgbe_close_suspend consequentially not freeing IRQ and crashing when
the remove handler calls pci_disable_device, hitting a BUG_ON at
free_msi_irqs, which asserts that there is no non-free IRQ associated
with the device to be removed:
BUG_ON(irq_has_action(entry->irq + i));
The issue is fixed by calling the ixgbe_close_suspend before evaluate
the pci channel state.
Reported-by: Naresh Bannoth <nbannoth@in.ibm.com>
Reported-by: Abdul Haleem <abdhalee@in.ibm.com>
Signed-off-by: Mauro S M Rodrigues <maurosr@linux.vnet.ibm.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch introduces support for the MPLS flow spec and
allows the creation of rules that are matching on the
MPLS label.
Applying the rule matching depends on the flow specs order and
the location of the MPLS in the spec list as there are different
configurations to be made in the device in the cases of MPLSoGRE
and MPLSoUDP vs. non-encapsulated MPLS.
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-05-17
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Provide a new BPF helper for doing a FIB and neighbor lookup
in the kernel tables from an XDP or tc BPF program. The helper
provides a fast-path for forwarding packets. The API supports
IPv4, IPv6 and MPLS protocols, but currently IPv4 and IPv6 are
implemented in this initial work, from David (Ahern).
2) Just a tiny diff but huge feature enabled for nfp driver by
extending the BPF offload beyond a pure host processing offload.
Offloaded XDP programs are allowed to set the RX queue index and
thus opening the door for defining a fully programmable RSS/n-tuple
filter replacement. Once BPF decided on a queue already, the device
data-path will skip the conventional RSS processing completely,
from Jakub.
3) The original sockmap implementation was array based similar to
devmap. However unlike devmap where an ifindex has a 1:1 mapping
into the map there are use cases with sockets that need to be
referenced using longer keys. Hence, sockhash map is added reusing
as much of the sockmap code as possible, from John.
4) Introduce BTF ID. The ID is allocatd through an IDR similar as
with BPF maps and progs. It also makes BTF accessible to user
space via BPF_BTF_GET_FD_BY_ID and adds exposure of the BTF data
through BPF_OBJ_GET_INFO_BY_FD, from Martin.
5) Enable BPF stackmap with build_id also in NMI context. Due to the
up_read() of current->mm->mmap_sem build_id cannot be parsed.
This work defers the up_read() via a per-cpu irq_work so that
at least limited support can be enabled, from Song.
6) Various BPF JIT follow-up cleanups and fixups after the LD_ABS/LD_IND
JIT conversion as well as implementation of an optimized 32/64 bit
immediate load in the arm64 JIT that allows to reduce the number of
emitted instructions; in case of tested real-world programs they
were shrinking by three percent, from Daniel.
7) Add ifindex parameter to the libbpf loader in order to enable
BPF offload support. Right now only iproute2 can load offloaded
BPF and this will also enable libbpf for direct integration into
other applications, from David (Beckett).
8) Convert the plain text documentation under Documentation/bpf/ into
RST format since this is the appropriate standard the kernel is
moving to for all documentation. Also add an overview README.rst,
from Jesper.
9) Add __printf verification attribute to the bpf_verifier_vlog()
helper. Though it uses va_list we can still allow gcc to check
the format string, from Mathieu.
10) Fix a bash reference in the BPF selftest's Makefile. The '|& ...'
is a bash 4.0+ feature which is not guaranteed to be available
when calling out to shell, therefore use a more portable variant,
from Joe.
11) Fix a 64 bit division in xdp_umem_reg() by using div_u64()
instead of relying on the gcc built-in, from Björn.
12) Fix a sock hashmap kmalloc warning reported by syzbot when an
overly large key size is used in hashmap then causing overflows
in htab->elem_size. Reject bogus attr->key_size early in the
sock_hash_alloc(), from Yonghong.
13) Ensure in BPF selftests when urandom_read is being linked that
--build-id is always enabled so that test_stacktrace_build_id[_nmi]
won't be failing, from Alexei.
14) Add bitsperlong.h as well as errno.h uapi headers into the tools
header infrastructure which point to one of the arch specific
uapi headers. This was needed in order to fix a build error on
some systems for the BPF selftests, from Sirio.
15) Allow for short options to be used in the xdp_monitor BPF sample
code. And also a bpf.h tools uapi header sync in order to fix a
selftest build failure. Both from Prashant.
16) More formally clarify the meaning of ID in the direct packet access
section of the BPF documentation, from Wang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When 'kvzalloc()' is used to allocate memory, 'kvfree()' must be used to
free it.
Fixes: fed9ce22bf ("net/mlx5: E-Switch, Add API to create vport rx rules")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When 'kvzalloc()' is used to allocate memory, 'kvfree()' must be used to
free it.
Fixes: 9efa752545 ("net/mlx5_core: Introduce access functions to query vport RoCE fields")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
For T6, clip table is separated from main TCAM. So, update LE-TCAM
collection logic to collect clip table TCAM as well. IPv6 takes
4 entries in clip table TCAM compared to 2 entries in main TCAM.
Also, in case of errors, keep LE-TCAM collected so far and set the
status to partial dump.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit b196d88aba ("tun: fix use after free for ptr_ring") we
need clean up tx ring during release(). But unfortunately, it tries to
do the cleanup blindly after socket were destroyed which will lead
another use-after-free. Fix this by doing the cleanup before dropping
the last reference of the socket in __tun_detach().
Reported-by: Andrei Vagin <avagin@virtuozzo.com>
Acked-by: Andrei Vagin <avagin@virtuozzo.com>
Fixes: b196d88aba ("tun: fix use after free for ptr_ring")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stress on qedi/qedr load unload lead to list_del corruption.
This is due to ll2 connection terminate freeing resources without
verifying that no more ll2 processing will occur.
This patch unregisters the ll2 status block before terminating
the connection to assure this race does not occur.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ll2 flows of flushing the txq/rxq need to be synchronized with the
regular fp processing. Caused list corruption during load/unload stress
tests.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should free all pending isles once it gets a FLUSH cqe from FW.
Part of iSCSI out of order flow.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stress on qedi/qedr load unload lead to list_del corruption.
This is due to ll2 connection terminate freeing resources without
verifying that no more ll2 processing will occur.
This patch unregisters the ll2 status block before terminating
the connection to assure this race does not occur.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ll2 flows of flushing the txq/rxq need to be synchronized with the
regular fp processing. Caused list corruption during load/unload stress
tests.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should free all pending isles once it gets a FLUSH cqe from FW.
Part of iSCSI out of order flow.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_disable_unprepare() already checks that the clock pointer is valid.
No need to test it before calling it.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The configuration settings for RBTX4927 were accidentally removed,
leading to a silently broken network interface.
Re-add the missing settings to fix this.
Fixes: 8eb97ff5a4 ("net: 8390: remove m32r specific bits")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces ops structure for sgmii, This by ensures that
we do not need dummy functions in case of emulation platforms.
Signed-off-by: Hemanth Puranik <hpuranik@codeaurora.org>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The command packet size is already checked once in
rmnet_map_deaggregate() for the header, packet and trailer size, so
this additional check is not needed.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ethtool private stats handler to debug the handling of packets
with checksum offload header / trailer. This allows to keep track of
the number of packets for which hardware computes the checksum and
counts and reasons where checksum computation was skipped in hardware
and was done in the network stack.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets in transmit path could potentially be dropped if there were
errors while adding the MAP header or the checksum header.
Increment the tx_drops stats in these cases.
Additionally, refactor the code to free the packet and increment
the tx_drops stat under a single label.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers have the following pattern:
if (np)
of_mdiobus_register()
else
mdiobus_register()
which the implementation of of_mdiobus_register() now takes care of.
Remove that pattern in drivers that strictly adhere to it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Antoine Tenart <antoine.tenart@bootlin.com>
Reviewed-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes klockworks warnings: Pointer 'dev' returned from call to
function 'bus_find_device' at line 179 may be NULL and will be dereferenced
at line 181.
cpsw-phy-sel.c:179: 'dev' is assigned the return value from function 'bus_find_device'.
bus.c:342: 'bus_find_device' explicitly returns a NULL value.
cpsw-phy-sel.c:181: 'dev' is dereferenced by passing argument 1 to function 'dev_get_drvdata'.
device.h:1024: 'dev' is passed to function 'dev_get_drvdata'.
device.h:1026: 'dev' is explicitly dereferenced.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
[nsekhar@ti.com: add an error message, fix return path]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was possible to delete only one half of an IPv6, which would leave
the second half still programmed and possibly in use. Instead of
checking for the unused bitmap, we need to check the unique bitmap, and
refuse any deletion that does not match that criteria. We also need to
move that check from bcm_sf2_cfp_rule_del_one() into its caller:
bcm_sf2_cfp_rule_del() otherwise we would not be able to delete second
halves anymore that would not pass the first test.
Fixes: ba0696c22e ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We had several issues that would make the programming of IPv6 rules both
inconsistent and error prone:
- the chain ID that we would be asking the hardware to put in the
packet's Broadcom tag would be off by one, it would return one of the
two indexes, but not the one user-space specified
- when an user specified a particular location to insert a CFP rule at,
we would not be returning the same index, which would be confusing if
nothing else
- finally, like IPv4, it would be possible to overflow the last entry by
re-programming it
Fix this by swapping the usage of rule_index[0] and rule_index[1] where
relevant in order to return a consistent and correct user-space
experience.
Fixes: ba0696c22e ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we let the kernel pick up a rule location with RX_CLS_LOC_ANY, we
would be able to overwrite the last rules because of a number of issues.
The IPv4 code path would not be checking that rule_index is within
bounds, and it would also only be allowed to pick up rules from range
0..126 instead of the full 0..127 range. This would lead us to allow
overwriting the last rule when we let the kernel pick-up the location.
Fixes: 3306145866 ("net: dsa: bcm_sf2: Move IPv4 CFP processing to specific functions")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1386c36b30.
We don't want to encourage drivers to not report carrier status
correctly, therefore remove this commit.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The micrel KSZ9031 phy has a optional clock pin (CLK125_NDO) which can be
used as reference clock for the MAC unit. The clock signal must meet the
RGMII requirements to ensure the correct data transmission between the
MAC and the PHY. The KSZ9031 phy does not fulfill the duty cycle
requirement if the phy is configured as slave. For a complete
describtion look at the errata sheets: DS80000691D or DS80000692D.
The errata sheet recommends to force the phy into master mode whenever
there is a 1000Base-T link-up as work around. Only set the
"micrel,force-master" property if you use the phy reference clock provided
by CLK125_NDO pin as MAC reference clock in your application.
Attenation, this workaround is only usable if the link partner can
be configured to slave mode for 1000Base-T.
Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
[m.felsch@pengutronix.de: fix dt-binding documentation]
[m.felsch@pengutronix.de: use already existing result var for read/write]
[m.felsch@pengutronix.de: add error handling]
[m.felsch@pengutronix.de: add more comments]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a mixed environment it may be difficult to tell if your hardware
support carrier, if it does not it can always report true. With a new
use_carrier option of 2, we can check both carrier and link status
sequentially, instead of one or the other
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx load balancing provided by balance-alb is not mutually
exclusive with using hashing for tx selection, and should provide a decent
speed increase because this eliminates spinlocks and cache contention.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace homegrown mac addr checks with faster defs from etherdevice.h
Note that this will also prevent any rlb arp updates for multicast
addresses, however this should have been forbidden anyway.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
arps for incomplete entries can't be sent anyway.
Signed-off-by: Debabrata Banerjee <dbanerje@akamai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When master device's mac has been changed, the commit
32c10bbfe9 ("ipvlan: always use the current L2 addr of the
master") makes the IPVlan devices's mac changed also, but it
doesn't do related works such as flush the IPVlan devices's
arp table.
Signed-off-by: Keefe Liu <liuqifa@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5e-updates-2018-05-14
Misc update for mlx5e netdevice driver
From Gal Pressman:
- Remove MLX5E_TEST_BIT macros and use test_bit instead
- Use __set_bit when possible
From Eran Ben Elisha:
- Improve debug print on initial RX posting timeout
From Or Gerlitz:
- Support offloaded TC flows with no matches on headers
- mlx5e TC cleanups
Trivial cleanups From Roi, Tariq and Saeed:
- Use bool as return type for mlx5e_xdp_handle
- Use u8 instead of int for LRO number of segments
- Skip redundant checks when providing NUD lastuse feedback
- Remove redundant vport context vlan update
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We call pcim_iomap in hclge_pci_init, pcim_iounmap should be called
in error handle of hclge_init_ae_dev.
We call pcim_iomap in hclge_pci_init, but do not call pcim_iounmap in
hclge_pci_uninit. When we remove the hclge.ko and insert it again, a
problem that pci can not map will happen. pcim_iounmap need to be called
in hclge_pci_uninit.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
