The error assigned does not seems to be used anywhere,
fixes nothing just a small cleanup
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For non-aggregated frames, ath9k was leaving handling of powersave
filtered packets to mac80211. This can be too slow if the intermediate
queue is already filled with packets and mac80211 does not immediately
send a new packet via drv_tx().
Improve response time with filtered frames by triggering clearing the
powersave filter internally.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It removes the need for undoing the padding changes to skb->data and it
improves performance by eliminating one tx status lookup per MPDU in the
status path. It is also useful for preparing a follow-up fix to better
handle powersave filtering.
A side effect is that these counters, available via debugfs, become now invalid:
* dot11TransmittedFragmentCount
* dot11FrameDuplicateCount,
* dot11ReceivedFragmentCount
* dot11MulticastReceivedFrameCount
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[kvalo@qca.qualcomm.com: add a note about counters, thanks to Zefir Kurtisi]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 7a0adc83f3 ("ath10k: improve tx scheduling") is causing
severe throughput drop in multi client mode. This issue is originally
reported in veriwave setup with 50 clients with TCP downlink traffic.
While increasing number of clients, the average throughput drops
gradually. With 50 clients, the combined peak throughput is decreased
to 98 Mbps whereas reverting given commit restored it to 550 Mbps.
Processing txqs for every tx completion is causing overhead. Ideally for
management frame tx completion, pending txqs processing can be avoided.
The change partly reverts the commit "ath10k: improve tx scheduling".
Processing pending txqs after all skbs tx completion will yeild enough
room to burst tx frames.
Fixes: 7a0adc83f3 ("ath10k: improve tx scheduling")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add NAPI support for rx and tx completion. NAPI poll is scheduled
from interrupt handler. The design is as below
- on interrupt
- schedule napi and mask interrupts
- on poll
- process all pipes (no actual Tx/Rx)
- process Rx within budget
- if quota exceeds budget reschedule napi poll by returning budget
- process Tx completions and update budget if necessary
- process Tx fetch indications (pull-push)
- push any other pending Tx (if possible)
- before resched or napi completion replenish htt rx ring buffer
- if work done < budget, complete napi poll and unmask interrupts
This change also get rid of two tasklets (intr_tq and txrx_compl_task).
Measured peak throughput with NAPI on IPQ4019 platform in controlled
environment. No noticeable reduction in throughput is seen and also
observed improvements in CPU usage. Approx. 15% CPU usage got reduced
in UDP uplink case.
DL: AP DUT Tx
UL: AP DUT Rx
IPQ4019 (avg. cpu usage %)
========
TOT +NAPI
=========== =============
TCP DL 644 Mbps (42%) 645 Mbps (36%)
TCP UL 673 Mbps (30%) 675 Mbps (26%)
UDP DL 682 Mbps (49%) 680 Mbps (49%)
UDP UL 720 Mbps (28%) 717 Mbps (11%)
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The patch corrects the revision id register and uses it along with
magic value and chip version registers to download appropriate firmware
image.
PCIe8997 Z chipset variant code has been removed, as it won't be used in
production.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch:
- improves code layout
- removes a useless memset(0) for some memory allocated with kzalloc
- removes a useless if. We know that 'if (chan_band_tlv)' will succeed
because it has been tested a few lines above
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements pre and post FLR handlers to support PCIe FLR
functionality. Software cleanup is performed in pre-FLR whereas
firmware is downloaded and software is re-initialised in
post-FLR handler.
Following command triggers FLR.
echo "1" > /sys/bus/pci/devices/$NUMBER/reset
This feature can be used as a recovery mechanism when firmware gets
hang.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In brcmf_sdio_kso_control() there is a retry loop as hardware may take
time to settle. However, when the call to brcmf_sdiod_regrb() returns
an error it is due to SDIO access failure and it makes no sense to wait
for hardware to settle. This patch aborts the loop after a number of
subsequent access errors.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver already supports the bcm4339 chipset but only for the variant
that shares the same modalias as the bcm4335, ie. sdio:c00v02D0d4335.
It turns out that there are also bcm4339 devices out there that have a
more distiguishable modalias sdio:c00v02D0d4339.
Reported-by: Steve deRosier <derosier@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds cfg80211 testmode support so that userspace tools can
download necessary commands to firmware during manufacturing mode tests.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
By default normal mode is chosen when driver is loaded. This
patch adds a provision to choose manufacturing mode via module
parameters.
Below command loads driver in manufacturing mode
insmod mwifiex.ko mfg_mode=1.
Tested-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git fixes for 4.8. Major changes:
ath10k
* fix racy rx status retrieval from htt context
* QCA9887 support is not experimental anymore, remove the warning message
ath9k
* fix regression with led GPIOs
* fix AR5416 GPIO access warning
A regression was introduced in commit id 79d4db1214 ("ath9k: cleanup
led_pin initial") that broken the WLAN status led on my laptop with
AR9287 after suspending and resuming.
Steps to reproduce:
* Suspend (laptop)
* Resume (laptop)
* Observe that the WLAN led no longer turns ON/OFF depending on the
status and is always red
Even though for my case it only needs to be set to OUT in ath9k_start
but for consistency bring back the IN direction setting as well.
Fixes: 79d4db1214 ("ath9k: cleanup led_pin initial")
Cc: Miaoqing Pan <miaoqing@codeaurora.org>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: <stable@vger.kernel.org> # 4.7+
Link: https://bugzilla.kernel.org/show_bug.cgi?id=151711
Signed-off-by: Giedrius Statkevičius <giedrius.statkevicius@gmail.com>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
%ul was likely meant as %lu to print an unsigned long,
not an unsigned with a letter l at the end.
But in fact the value printed is u32 anyway, so just drop
the l completely.
Signed-off-by: Oleg Drokin <green@linuxhacker.ru>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Printing about 3000 lines like this
[ 20.691850] mwifiex_pcie 0000:02:00.0: .
[ 20.693466] mwifiex_pcie 0000:02:00.0: .
is not useful. If FW downloading will be interrupted, we will get
proper error message about that.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For debugging purpose print content of reg->fw_status register and other
variables values when waiting for firmware ready event.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Printing ret and adapter->winner do not provide any useful information
as those are always 0 at point where the massage is printed. Print value
read from reg->fw_status register instead.
Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add time sync configuration api.
The new api allows to configure the synchronization
mode (STA/AP/MESH) and (in case of Mesh mode) the
master address of each zone.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The struct cfg80211_pmksa defines its bssid field as:
const u8 *bssid;
contrary to struct brcmf_pmksa, which uses:
u8 bssid[ETH_ALEN];
Therefore in brcmf_cfg80211_del_pmksa(), &pmksa->bssid takes the address
of this field (of type u8**), not the one of its content (which would be
u8*). Remove the & operator to make brcmf_dbg("%pM") and memcmp()
behave as expected.
This bug have been found using a custom static checker (which checks the
usage of %p... attributes at build time). It has been introduced in
commit 6c404f34f2 ("brcmfmac: Cleanup pmksa cache handling code"),
which replaced pmksa->bssid by &pmksa->bssid while refactoring the code,
without modifying struct cfg80211_pmksa definition.
Replace &pmk[i].bssid with pmk[i].bssid too to make the code clearer,
this change does not affect the semantic.
Fixes: 6c404f34f2 ("brcmfmac: Cleanup pmksa cache handling code")
Cc: stable@vger.kernel.org
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The AE1200 comes with different revisions of the BCM43235 chipset,
but all have the same USB ID. Only revision 3 can be supported.
Signed-off-by: Ismael Luceno <ismael@iodev.co.uk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Some RTL8821AE devices sold in Great Britain have the country code of
0x25 encoded in their EEPROM. This value is not tested in the routine
that establishes the regulatory info for the chip. The fix is to set
this code to have the same capabilities as the EU countries. In addition,
the channels allowed for COUNTRY_CODE_ETSI were more properly suited
for China and Israel, not the EU. This problem has also been fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On my home network rtl8xxxu is spamming the log with
IEEE80211_AMPDU_RX_START / IEEE80211_AMPDU_RX_STOP every few seconds
turn these messages into debug messages.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
[kvalo@codeaurora.org: fix commit title]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warning:
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:898:1: warning:
symbol 'rtl8xxxu_gen1_h2c_cmd' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Split the filling of TX descriptors into a generic portion used on all
devices, and format specific helper functions provided in the fops
structure.
This also cleaned up some mess, even if non harmful, in the handling
of txdesc40 descriptors, where the code randomly would switch between
the pointer to tx_desc and tx_desc40.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Another patch to move this detection out of the code handling the TX
descriptor update.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to be able to split out the TX descriptor handling code,
determine in advance the need to mark SGI.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Calculating the value in one place rather than using one calculation
in one place and a different one for management frames in another
location makes little sense.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not rely on TX descriptor size to determine the thermal meter
type.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use a fileops flag to indicate whether the device has TX report timer
support. This will make it easier to include future devices such as
8188eu to use the TX report timer.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These are primarily needed for SDIO/PCI parts, but the vendor driver
still sets them for some USB devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With all devices now offering fops->total_page_num, get rid of the
if mess for setting the TX buffer boundary.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Switching over the old devices to use the new function allows us to
get rid of this legacy.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was the last user of the old
rtl8xxxu_old_init_queue_reserved_page() which can now be removed.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This changes the pub-queue value written to REQ_RQPN, however the old
code used a hard coded minimum value assuming there would always be an
active lo-queue, even when no USB EP was found for it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This switches the 8723b driver to use the new
rtl8xxxu_init_queue_reserved_page() function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some reason we lost the code bailing if rtl8xxxu_init_device()
returned an error.
This catches the error and also cleans up the error handling.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This field was added to wl_sta struct to get hw in situations
where it was not given to driver by mac80211. In our case,
get_expected_throughput op did not send hw to driver.
This patch reverts the change, as it is no longer needed due to commit
4fdbc67a25 ("mac80211: call get_expected_throughput only after adding
station") as hw is now sent as a parameter.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of (rtlhal->oem_id != RT_CID_DEFAULT), the function directly
returns and leaks the already allocated hwinfo memory. Go through the
correct exit path.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case rtl_get_hwinfo() fails, the function directly returns and leaks the
already allocated hwinfo memory. Go through the correct exit path.
Signed-off-by: Christian Engelmayer <cengelma@gmx.at>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
