If the HW is not responding at probe time, fail immediately complaining
about it. Without this, we see that the kernel spends > 100ms trying to
load firmware (even gives an incorrect impression that it actually
loaded a firmware) and do unnecesary processing before concluding that
the device is not accessible:
INFO kernel: [ 34.092678] iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
WARNING kernel: [ 34.093560] iwlwifi 0000:01:00.0: Direct firmware load for iwl-dbg-cfg.ini failed with error -2
INFO kernel: [ 34.111523] iwlwifi 0000:01:00.0: loaded firmware version 17.318154.0 op_mode iwlmvm
INFO kernel: [ 34.173250] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AC 7265, REV=0xFFFFFFFF
ERR kernel: [ 34.198023] iwlwifi 0000:01:00.0: iwlwifi transaction failed, dumping registers
ERR kernel: [ 34.198044] iwlwifi 0000:01:00.0: iwlwifi device config registers:
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This will allow us to reuse the function later for adding fraglist
SKBs to the TFD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When anything fails, we unmap the whole TFD in three different
places scattered throughout the code. Unify this to a single
place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the incoming frame should be an A-MSDU, it may already be one,
for example in the case of NAN multicast being encapsulated in an
A-MSDU. Thus, use the GSO algorithm to build A-MSDU only if the
skb actually contains GSO data.
Fixes: 6ffe5de35b ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Annotate the compressed BA notification array sizes and
make both of them 0-length since the length of 1 is just
confusing - it may be different than that and the offset
to the second one needs to be calculated in the C code
anyhow.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make the adjustments for gen2 TX and RX of TKIP packets. Strip MIC on
RX. Don't add IV space and keep the MIC space zeroed on TX.
Devices that support gen2 data path support TKIP only in station mode.
In all other modes, fall back to SW encryption. Do this early in the
set_key() callback so that the key flags would not be incorrectly set.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For newer devices we have higher range of periphery
addresses. Currently it is masked out, so we end up
reading another address.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to receive TB (Trigger Based) PPDU in monitor mode,
the Driver must send the HE_AIR_SNIFFER_CONFIG_CMD host command.
Enable that via debugfs.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The non-shared antenna was wrong for 22000 device series.
Fix it to ANT_B for correct antenna preference by coex in MVM driver.
Fixes: e34d975e40 ("iwlwifi: Add a000 HW family support")
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We can dump data from the firmware either when it crashes,
or when the firmware is alive.
Not all the data is available if the firmware is running
(like the Tx / Rx FIFOs which are available only when the
firmware is halted), so we first check that the firmware
is alive to compute the required size for the dump and then
fill the buffer with the data.
When we allocate the buffer, we test the STATUS_FW_ERROR
bit to check if the firmware is alive or not. This bit
can be changed during the course of the dump since it is
modified in the interrupt handler.
We hit a case where we allocate the buffer while the
firmware is sill working, and while we start to fill the
buffer, the firmware crashes. Then we test STATUS_FW_ERROR
again and decide to fill the buffer with data like the
FIFOs even if no room was allocated for this data in the
buffer. This means that we overflow the buffer that was
allocated leading to memory corruption.
To fix this, test the STATUS_FW_ERROR bit only once and
rely on local variables to check if we should dump fifos
or other firmware components.
Fixes: 04fd2c2822 ("iwlwifi: mvm: add rxf and txf to dump data")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Alexei's patch, assumed that all versions of "struct iwl_error_event_table"
are the same, but there are really different versions in different files.
Rather than trying to fix this, or splitting the tracepoint, or anything of
the sort, just remove it entirely - turns out that nobody really uses it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We already report the RU offset, so we'd better also
report that we know the value.
Fixes: e5721e3f77 ("iwlwifi: mvm: add radiotap data for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Cleanup of the debug flow by moving several flows to separate
functions to increase readability. Three functions were created:
1. iwl_fw_get_prph_len - returns the size needed for periphery dump.
2. iwl_fw_dump_mem for - executes the memory dumping flow.
3. iwl_trans_get_fw_monitor_len - returns the size needed for monitor dump.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no value in having an anonymous struct for holding
a few fields, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In new devices, access to periphery is forbidden. Send instead
host command to start and stop debugging.
Memory allocation is written in context info, but in case we
need to update it there is a dedicated command. Add definitions,
currently unused, of the new command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the restart FW debug code to a function. This avoids code
duplication and lays the infra to support the new start and stop
host commands in some future devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The SP length in the ADD_STA command is an actual number of
frames, and not the SP len as it appears in the WME IE.
Fix that comment. The actual code is fine.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The allocation of hwsim radio identifiers uses a post-increment from 0,
so the first radio has idx 0. This idx is explicitly excluded from
multicast announcements ever since, but it is unclear why.
Drop that idx check and announce the first radio as well. This makes
userspace happy if it relies on these events.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The asynchronous destruction from a work-queue of radios tagged with
destroy-on-close may race with the owning namespace about to exit,
resulting in potential use-after-free of that namespace.
Instead of using a work-queue, move radios about to destroy to a
temporary list, which can be worked on synchronously after releasing
the lock. This should be safe to do from the netlink socket notifier,
as the namespace is guaranteed to not get released.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The cleanup of radios during namespace exit has recently been reworked
to directly delete a radio while temporarily releasing the spinlock,
fixing a race condition between the work-queue execution and namespace
exits. However, the temporary unlock allows unsafe modifications on the
iterated list, resulting in a potential crash when continuing the
iteration of additional radios.
Move radios about to destroy to a temporary list, and clean that up
after releasing the spinlock once iteration is complete.
Fixes: 8cfd36a0b5 ("mac80211_hwsim: fix use-after-free bug in hwsim_exit_net")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/quantenna/qtnfmac/cfg80211.c: In function 'qtnf_dump_survey':
drivers/net/wireless/quantenna/qtnfmac/cfg80211.c:694:19: warning:
variable 'vif' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The ucode chunk might be relatively large and the allocation with
kmalloc() may fail occasionally. Since the data isn't DMA-transferred
but by manual loops, we can use vmalloc instead of kmalloc.
For a better performance, though, kvmalloc() would be the best choice
in such a case, so let's replace with it.
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1103431
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_rxglom':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:1466:11: warning:
variable 'sfdoff' set but not used [-Wunused-but-set-variable]
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c: In function 'brcmf_sdio_bus_preinit':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/sdio.c:3408:7: warning:
variable 'pad_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
debugfs_remove_recursive has taken IS_ERR_OR_NULL into account. So just
remove the condition check before debugfs_remove_recursive.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When obtaining the firmware capability a buffer is provided of 512
bytes. However, if all features in firmware are supported the buffer
needs to be 565 bytes as otherwise truncated information is retrieved
from firmware. Increasing the buffer to 768 bytes on stack.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 66cffd6daa ("b43: fix transmit failure when VT is switched"),
a condition is noted where the network controller needs to be reset. Note
that this situation happens when running the open-source firmware
(http://netweb.ing.unibs.it/~openfwwf/), plus a number of other special
conditions.
for a different card model, it is reported that this change breaks
operation running the proprietary firmware
(https://marc.info/?l=linux-wireless&m=153504546924558&w=2). Rather
than reverting the previous patch, the code is tweaked to avoid the
reset unless the open-source firmware is being used.
Fixes: 66cffd6daa ("b43: fix transmit failure when VT is switched")
Cc: Stable <stable@vger.kernel.org> # 4.18+
Cc: Taketo Kabe <kabe@sra-tohoku.co.jp>
Reported-and-tested-by: D. Prabhu <d.praabhu@gmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove mt76_fw dependency from mt76x0u_upload_firmware routine since
it does not define firmware layout properly. Moreover use mt76_poll_msec
utility routine to check if the fw is properly running
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove unused usb header file and move mt76x0 firmware definition
in usb.c
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mcu.c source file since it contains just 'one-line' function
that is shared between PCI and USB code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Using the NAPI or netdev frag cache along with other drivers can lead to
32 KiB pages being held for a long time, despite only being used for
very few page fragments.
This can happen if the driver grabs one or two fragments for rx ring
refill, while other drivers use (and free up) the remaining fragments.
The 32 KiB higher-order page can only be freed once all users have freed
their fragments.
Depending on the traffic patterns, this can waste a lot of memory and
look a lot like a memory leak.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_phy_tssi_compensate routine in mt76x2-common module
since it is shared between mt76x2 and mt76x2u drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mcu_calibrate routine in mt76x02-lib module since it is
shared between USB and PCI code. Moreover remove duplicated
code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move shared mt76x2 {pcie/usb} mcu shared code in a common file
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move shared mt76x2/mt76x0 mcu shared code in a common file
and remove duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt76x2_fw_header definition in mt76x02_mcu.h and remove
duplicated code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mcu common helpers instead of mt76x2 specific routines for
mcu_alloc_msg()/mcu_send_msg(). This is a preliminary patch to
unify mt76e and mt76u mcu code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76_dev data structure instead of mt76x2_dev one in mt76x2_mcu_msg_send
and mt76x2_mcu_get_response routines. Moreover add wait_resp parameter to
mt76x2_mcu_msg_send signature. This is a preliminary patch in order to unify
mcu_msg_alloc()/mcu_msg_send() between pcie and usb code
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move __iomem regs pointer in mt76_mmio data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_mmio data structure in mt76_dev and
move mt76x2_mcu in mt76_mmio. This is a preliminary
patch to unify mcu code between mt76x02{e,u} drivers
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove unused usb buffer in mt76x2_mcu data structure
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use mt76_dev data structure instead of mt76x2_dev one in
mt76x2_tx_queue_mcu routine. This is a preliminary patch
to share mcu code between mt76x2e and mt76x0e
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76_mcu_msg_alloc return value check since it is already
evaluated in __mt76x02u_mcu_send_msg
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We don't need to use custom burst write regs via MCU, we can use
generic mt76_wr_copy() for the same purpose.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
mt76x0_burst_read_regs is not used, but keep it for eventual use. Since
we have this function now in the driver git history, we can remove it and
eventually revert this commit it the function will be needed.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
