DIAG_TRANSFER_LIMIT is redefined with same value and comments
just below this entry, remove this duplicate entry.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Symbolic permissions are no longer recommended.
This patch changes the symbolic permissions in wil6210 driver
to octal permissions.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add an option to specify and override the A-BFT length when
starting an AP/PCP. See IEEE P802.11-2016, 10.38.5.
The abft_len must be set before starting AP/PCP. It is only
needed for diagnostics and certification.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add reporting of the association ID (AID) for each station
as part of the stations file in the debugfs.
Valid AID values are 1-254. 0 is reported if the AID
is unknown or not reported by firmware.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently we do not have full support for broadcast from
a station inside a PBSS network.
We have a workaround where instead of broadcast we do a
unicast to every known station in the PBSS.
This workaround was performed only for P2P clients.
This fix will perform the broadcast workaround also for a
regular station inside a PBSS.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
During reset sequence it is seen that device is generating an
interrupt eventhough interrupts are masked at device level.
Add workaround to disable the interrupts from host side during
reset and clear any pending interrupts before re-enabling
the interrupt.
Signed-off-by: Hamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The code in wmi_call uses the wil->wmi_call completion
structure to wait for a reply.
In some scenarios, complete was called twice on the
completion structure. This happened mainly with a disconnect
event which can arrive both unsolicited and as a reply to
a disconnect request. In this case the completion structure
was left marked as "done" and the next wmi_call returned
immediately with a corrupted reply buffer. This caused
unexpected results including crashes.
Fix this by adding the missing call to reinit_completion.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI_ONLY FW is used for testing in production. It cannot be used for
scan/connect, etc.
In case FW reports this capability, driver will not allow interface up.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
__func__ is automatically added to printouts by dynamic debug
mechanism and by wil_info/wil_err macros.
Remove __func__ from debug printouts to avoid duplication.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Driver may be used in platforms where some use sparrow cards while
other use sparrow-plus cards, where different FW image is needed.
Add the capability to load dedicated FW image in case sparrow-plus
card is detected and fallback to default image if such does not exist.
Signed-off-by: Lazar Alexei <qca_ailizaro@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By default, AP SME is handled by driver/FW.
In case disable_ap_sme is true, driver doesn't turn-on
WIPHY_FLAG_HAVE_AP_SME and the responsibility for
AP SME is passed to user space.
With AP SME disabled, driver reports assoc request frame
to user space which is then responsible for sending assoc
response frame and for sending NL80211_CMD_NEW_STATION.
Driver also reports disassoc frame to user space
which should then send NL80211_CMD_DEL_STATION.
NL80211_CMD_SET_STATION with NL80211_STA_FLAG_AUTHORIZED
is used by user space to allow/disallow data transmit.
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When removing inactive queue - use the central disable queue
function. This is needed due to a000 changes to come, but is
a proper cleanup anyway.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value returned from iwl_mvm_send_cmd_pdu() in this function is not
used and always returns an error (which is the whole point of the
call). Tag the ret variable with __maybe_unused to avoid this compile
warning when W=1 is used:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/debugfs.c: In function ‘iwl_dbgfs_fw_restart_write’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/debugfs.c:875:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When compiling with W=1, we get the following warning in debugfs.c:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/debugfs.c: In function ‘iwl_dbgfs_fw_restart_write’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/debugfs.c:2313:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret;
^
Fix it by ignoring the return value in this case.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Remove the sta_id variable, to avoid this compile warning when
compiling with W=1:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/sta.c: In function ‘iwl_mvm_change_queue_owner’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/sta.c:871:5: warning: variable ‘sta_id’ set but not used [-Wunused-but-set-variable]
s8 sta_id;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The return value from this function is never used, so make it return
void to avoid getting the following warning when compiling wiht W=1:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/rs.c: In function ‘rs_tl_turn_on_agg_for_tid’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/dvm/rs.c:400:6: warning: variable ‘load’ set but not used [-Wunused-but-set-variable]
u32 load;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
shift_param is defined and set in iwl_pcie_load_cpu_sections but not
used. Fix this to avoid -Wunused-but-set-variable warning.
The code using it turned into dead code with commit dcab8ecd56
("iwlwifi: mvm: support ucode load for family_8000 B0 only") which
added a separate function iwl_pcie_load_given_ucode_8000 (then 8000b)
for IWL_DEVICE_FAMILY_8000. Commit 76f8c0e17e ("iwlwifi: pcie:
remove dead code") removed the dead code but left shift_param as is.
iwlwifi/pcie/trans.c: In function ‘iwl_pcie_load_cpu_sections’:
iwlwifi/pcie/trans.c:871:6: warning: variable ‘shift_param’ set but not used [-Wunused-but-set-variable]
Fixes: dcab8ecd56 ("iwlwifi: mvm: support ucode load for family_8000 B0 only")
Fixes: 76f8c0e17e ("iwlwifi: pcie: remove dead code")
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Sara Sharon <sara.sharon@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Liad Kaufman <liad.kaufman@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[removed some unnecessary braces]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Commit 5fc0f76c4 introduced Rx stats from debugfs, the function
iwl_mvm_reset_frame_stats from that commit defines and sets mcs but
does not use it. Compiling iwlwifi with W=1 gives this warning -
iwlwifi/mvm/rs.c: In function ‘iwl_mvm_update_frame_stats’:
iwlwifi/mvm/rs.c:3074:14: warning: variable ‘mcs’ set but not used [-Wunused-but-set-variable]
Fixes: 5fc0f76c43 (iwlwifi: mvm: add Rx frames statistics via debugfs)
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
mvmvif is defined and set in rs_mimo_allow but not used. Compiling
iwlwifi with W=1 gives the following warning, remove it. mvmsta is
used only to obtain mvmvif so remove it as well.
iwlwifi/mvm/rs.c: In function 'rs_mimo_allow':
iwlwifi/mvm/rs.c:165:22: warning: variable 'mvmvif' set but not used.[-Wunused-but-set-variable]
This fix removes calls to iwl_mvm_sta_from_mac &
iwl_mvm_vif_from_mac. They are both accessors, and do not have any
side-effects. Commit e621c2282e ("iwlwifi: rs: Remove workaround
that disables MIMO on P2P") removed a workaround that disabled MIMO on
P2P, 'mvmvif' was used for that workaround, but not removed with it.
Fixes: e621c2282e ("iwlwifi: rs: Remove workaround that disables MIMO on P2P")
Signed-off-by: Kirtika Ruchandani <kirtika@google.com>
Cc: Alexander Bondar <alexander.bondar@intel.com>
Cc: Emmanuel Grumbach <emmmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The temperature variable is set but not used in
iwl_mvm_handle_statistics(). Remove it to avoid the following
compiler warning when W=1 is used:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/rx.c: In function ‘iwl_mvm_handle_rx_statistics’:
/home/luca/iwlwifi/stack-dev/drivers/net/wireless/intel/iwlwifi/mvm/rx.c:759:6: warning: variable ‘temperature’ set but not used [-Wunused-but-set-variable]
u32 temperature;
^
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
IWL6000G2B_UCODE_API_MAX is not defined. ucode_api_max of
IWL_DEVICE_6030 uses IWL6000G2_UCODE_API_MAX. Use this also for
MODULE_FIRMWARE.
Fixes: 9d9b21d1b6 ("iwlwifi: remove IWL_*_UCODE_API_OK")
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For 9000 devices withg upload, FW cannot send the entire phy
flags, and will send only the band - which is what we really
care about anyway. Change is backward compatible.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In preparation for the new TX cmd - move the rate calculation
to a diffrent function, and make it independent of the TX
command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the function changes the TX cmd itself.
Make it more generic by returning a value, as preperation
to the new TX cmd.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The maximum number of firmware sections is now 32 instead of 16 for
a000 devices. Set the appropriate define. Avoid out of bounds access
in case there are more sections than the maximum set by driver.
Make the driver extensible to FW size changes by allocating the
section memory dynamically.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The logic in the paging calculations is a bit hard to
follow. Replace it with a kernel define.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some of the code there is duplicate while the only change is
the block size. Unifying it shortens the code and make the
difference clearer.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When copying from vmalloc'ed memory to the SG list, don't crash
if the transport didn't provide any data.
Fixes: 7e62a699aa ("iwlwifi: mvm: use dev_coredumpsg()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Due to some new features and changes, the firmware file will now
specify what type of memory to dump, in upper 8 bits of the type
field of the TLV. Parse it (types we don't understand are errors)
and teach the code to dump periphery memory.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no reason to be validating the memory dump types, or
checking them for duplication, or anything, since we really
just pass them through from the TLV to the dump.
Thus, change the way we handle memory dump TLVs to let the
driver just blindly use anything specified there, dumping it
into the memory dump output file.
This makes the system extensible without driver changes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For unified images, we shouldn't restart the HW if suspend fails. The
only reason for restarting the HW with non-unified images is to go
back to the D0 image.
Fixes: 23ae61282b ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the relevant fields to export the 32-bit device timestamp to
radiotap using the new mac80211 infrastructure. This will be useful
to allow synchronising monitor captures taken on different hardware
simultaneously.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When the firmware restarts in a situation in which any station
has no queue reserved anymore because that queue was used, the
code will crash trying to access the queue_info array at the
offset 255, which is far too big. Fix this by checking that a
queue is actually reserved before writing its status.
Fixes: 8d98ae6eb0 ("iwlwifi: mvm: re-assign old queues after hw restart in dqa mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Mistakenly, the driver is trying to load the 8000C firmware with an
incorrect name (i.e. with two hyphens where there should be only one)
and that fails. Fix that by removing the hyphen from the format
macro.
Fixes: e1ba684f76 ("iwlwifi: 8000: fix MODULE_FIRMWARE input")
Signed-off-by: Jürg Billeter <j@bitron.ch>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A recent firmware change seems to have enabled thermal zones on the
iwlwifi driver. Unfortunately, my device fails when registering the
thermal zone. This doesn't stop the driver from attempting to unregister
the thermal zone at unload time, triggering a NULL pointer deference in
strlen() off the thermal_zone_device_unregister() path.
Don't unregister if name is NULL, for that case we failed registering.
Do the same for the cooling zone.
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These drivers use a set of complicated macros to extract and insert
information for the RX and TX descriptors. Driver rtl8192cu had a
different set than was used for the PCI-based drivers. To simplify
the code, rtl8192cu is switched to use the common version. In the
process, two errors in those common macros were found and fixed.
Besides simplifying the code, there is an additional benefit. We have
no BE hardware to test the PCI driver, but using the common macros
provides an additional test for the validity of many endian-sensitive
operations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver requires a checksum for the descriptors so that the wifi
chip is assured that the USB transmission was correct. These entries
are little-endian, but the driver was always using cpu order in the
calculation. As a result, the driver failed on BE hardware.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware is read from disk as a little-endian byte string. The code
that loads the firmware into the device transfers it as 4-byte quantities.
The routines that write multi-byte quantities on BE hardware assume that
the data are in CPU order, and automatically do the conversion to the LE
order required by the device. As a result, the firmware is transmitted
incorrectly. Rather than do multiple byte swaps on the data, the download
routine is revised to transmit bytes rather than dwords. Although the
number of I/O operations is increased, the firmware is not often loaded.
All drivers have the same bug, and use essentially the same code to
download firmware. These routines have been moved into rtlwifi.
Some CamelCase variables have been renamed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the kernel provides access to module parameters through entries in
/sys/module/<driver>/parameters/, there is no need for a private
interface. Thus the existing code for setting the debug level is
removed.
Reported-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The debugging macros contain a parameter COMP_XX that could be used as a
mask; however, the code turns all these various bits on at the same time.
This change implements them as a proper mask, and adds module parameters
to set the mask at load time.
The current name "debug" for the debug level has been changed to
"debug_level" to better differentiate it from "debug_mask".
The debug routines have also been changed to interrogate the structure
that is loaded at entry time. As a result, the structure rtl_debug is no
longer needed, and all references to it are deleted.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These two debugging formss implement debugging using rather complicated
macro constructions. These are replaced with compiled code that is easier
to understand.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This intends to make init/attach process slightly easier to follow.
What driver was doing in brcmf_bus_start wasn't bus specific at all and
function brcmf_bus_stop wasn't undoing things done there. This function
is supposed to be called by bus specific code when the bus is ready.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver used to call brcmf_bus_detach only from one place and it already
contained a check for drvr not being NULL. We can get rid of this extra
function, call brcmf_bus_stop directly and simplify the code.
There also isn't brcmf_bus_attach function which one could expect so it
looks more consistent this way.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Functions brcmf_c_prec_enq and brcmf_sdio_init don't exist so we
really don't need their declarations. Function brcmf_parse_tlvs is used
in cfg80211.c only so make it static and drop from header as well.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
