There are several occasions where a scan of the same type is requested
concurrently, so logging every time this happens is just noisy and
unnecessary. Remove the logging for these cases.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 FW moved to 15 as management TID.
The change for us is fairly local - translate old TID to 15
when enabling and disabling a queue, and make sure to cover
it also on TX responses.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
a000 devices queue management is going to change significantly.
We will have 512 queues. Those queues will be assigned number
by the firmware and not by the driver.
In addition, due to SN offload having TX queue shared between TIDs
is impossible
Also, the ADD_STA command no longer updates queues status.
The only point of changing queue in the SCD queue config API.
From driver perspective we have here a new design:
Queue sharing and inactivity checks are disabled.
Once this is done, the only paths that call scd_queue_cfg command
are paths that alloc and release TX queues - which will make future
accommodation to queue number assignment by FW easier.
Since allocating 512 queues statically is not advisable, transport
will allocate the queue on demand, fill the command with DRAM data
and send it. This is reflected in the new transport API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 devices the TX handling is different in a few ways:
* Queues are allocated dynamically
* DQA is enabled by default
* Driver shouldn't access TFH registers - ucode configures it
all in SCD_QUEUE_CFG command
Support all this in a new API with op mode, where op mode sends
the command, transport will allocate the queue dynamically, fill
in DMA properties, send the command to FW and get the ID back.
Current implementation only sets the new transport API and fills
the DMA properties.
Future patches will complete the other parts.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support the new TX command API for a000 devices.
Command is a very slim version of current TX command.
Generalize iwl_mvm_tx_mpdu to get rid of TX command dependencies.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Dynamic SAR allows changing TX power limits at runtime to comply with
SAR regulations on multiple form factors (e.g. tablet vs. clamshell
mode). To support this, a new table was added to ACPI, which is
called Extended Wireless Regulatory Descriptor (EWRD). This table
allows OEMs to define different TX power profiles for each form-factor
or usage mode.
Read this new table and store it in our SAR profiles table, in
preparation for Dynamic SAR support.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For dynamic SAR, we will need to select the current profile from
different places. In preparation for that, spin the profile selection
code out of iwl_mvm_sar_init().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We are adding support for dynamic TX power tables for SAR (specific
absorption rate) compliance. Currently, we only support a single
(static) TX power table, which is read from ACPI, and use it
statically.
To prepare for more tables that can be switched dynamically, refactor
the SAR init flow to allow reusage and add the current static table as
a single entry in an array of tables.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Firmware isn't configuring multi RX queue hardware yet in
the self init mode.
Disable it for now until we have an API that enables it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
API will be the same regardless of FW compilation.
CDB related values will be filled in only for CDB.
Cahneg code and names accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 devices we will support up to 32 stations.
The max station define is used also for invalid station marking
which makes finding usages of actual maximum station pretty hard
to sort through - change it to be a different define in order
to make future changes easier.
Use also ARRAY_SIZE intead of define when possible.
Do not move yet to 32 stations until firmware do it though.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently aux & broadcast queues are added before calling add
station, which results with a SCD_QUEUE_CFG command sent with
a station id unknown yet to fw.
While this works for pre-a000 firmware, the a000 fw requires
the order to be reversed.
The reason the change is only for a000 devices and not for
previous devices is that we cannot reverse the order since
the tfd_queue_mask containing the aux queue will cause FW to
assert on adding a queue mask with a queue that is not enabled.
This is not a problem in a000 fw since the tfd_queue_mask was
removed from the add sta API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As per latest regulatory update for India, channel 52, 56, 60, 64
is no longer restricted to DFS. Enabling DFS/no infra flags in driver
results in applying all DFS related restrictions (like doing CAC etc
before this channel moves to 'available state') for these channels
even though the country code is programmed as 'India' in he hardware,
fix this by relaxing the frequency range while applying RADAR flags
only if the country code is programmed to India. If the frequency range
needs to modified based on different country code, ath_is_radar_freq
can be extended/modified dynamically.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Introduce a debugfs option to manually override the noise floor,
ignoring the automatically tuned noise floor of the driver/hw.
In my tests with a AR9580 based module and a tx99 5 MHz interferer,
I could tune the noisefloor to -95 dBm or above to allow communication
again. The automatic noise floor calibration sometimes could adapt to
the situation as well, but not reliably and permanently.
I would consider this "feature" experimental and interesting for people
debugging the noise floor calibration or other effects of the hardware.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fit.fraunhofer.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
For QCA6174 hw3.0, since WLAN.RM.4.4-00022-QCARMSWPZ-2, it starts to
support the board ID information from otp, with some devices released on
the market that didn't calibrated with OTP, will have 0 for board ID
information, which cause the backward compatibility issue and was fixed
in commit 'd2e202c06ca4 ("ath10k: ignore configuring the incorrect board_id")'
So bump the fw api version to differentiate the latest firmware support.
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
spectral_bin length (number of bins per fft sample) is usually
a value where (2^n = value), n is an integer. All of the QCA99X0
family of chipsets seems to report a spectral_bin length of
2^n + 'm' bytes, where m = 4, 12 based on the chipset. This 'm'
bytes seems to carry some radar related info which is currently
discarded only for 'bin_len = 68' bytes. Extend this discarding of
irrelevant 'bin_len' for QCA9984, QCA9888, IPQ4019 as well by
introducing a hardware parameter 'spectral_bin_discard'. Also
for QCA988X based family of chipsets which doesn't seem to have this
issue and also for some of the hardware which I have not tested
like QCA6174/QCA9377 the existing behaviour is retained as it is.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The macro results are assigned to u8 variables/fields. Adding the cast
fixes plenty of clang warnings about "implicit conversion from 'int' to
'u8'".
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the Dell Wireless 1601 card as an AR9462 in the ath9k pci list.
Note that the wowlan feature is supported and has been tested
successfully.
Signed-off-by: Damien Thébault <damien@dtbo.net>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The > should be >= or we read one space beyond the end of the array.
Fixes: ab5c4f71d8 ("ath9k: allow to load EEPROM content via firmware API")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The fwsignal module is only referenced by the bcdc module and part of the
bcdc protocol. So only build it when CONFIG_BRCMFMAC_PROTO_BCDC is selected.
Fixes: acf8ac41dd ("brcmfmac: remove reference to fwsignal data from struct brcmf_pub")
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Patches intended for v4.12:
* Some small fixes here and there;
* The usual cleanups and small improvements;
* Work to support A000 devices continues;
* New FW API version;
* Some debugging improvements;
Pass the new extended ACK reporting struct to all of the generic
netlink parsing functions. For now, pass NULL in almost all callers
(except for some in the core.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consequently refer to external PA instead of inverting the logic and
use an internal PA capability flag which is a bit confusing.
Currently this is used for Rt3352 only, but MT7620A also allows for an
external PA which will be supported by a follow up patch.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
