This patch apply an extensible firmware dump framework,
so that other chipset can be easily added as needed.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
memory_type_mapping strucuture did not refer to other mwifiex
specific strture. A better software design method would keep
it in decl header file, which does not include other mwifiex
header file.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If we are not able to read registers or PCIe memory,
it means PCIe device is in bad state. We will skip
firmware dump in this case.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is observed that ioread32 may fail to read pcie register
in certain scenarios, this patch handles these cases.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
drv_pkt_delay_max should be assigned non-zero value, so that
packet delay can be accumulate in the right way.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds an interface for handling commands like
iwconfig wlanX power on/off. Such an interface formerly existed
when the driver used wext.
While performance with sdio in polling mode without using
powersave mode is quite bad, powersaving mode is unusable,
so do not enable it under such conditions.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the device is remove e.g. because of going to suspend
mode with powersaving enabled, lbs_remove_card tries to exit
powersaving state even when already woken up. That command is
not processed properly in that situation, since the command
processing queue is already stopped, so it waits forever
for the command being processed, so disable it.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removes the old todo block and checks only whether ieee powersave
mode is requested. We still have to check for being connected as
this powersave mode includes logic for regularly waking up and
checking for packets which only makes sense when connected.
For not being connected, another mode is needed.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the main thread gets one PS AWAKE event and one PS SLEEP event
in one iteration over event_fifo there will never be checks for
commands to be processed, since psstate will always be
PS_STATE_SLEEP or PS_STATE_PRE_SLEEP
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If a sdio host does not support sdio irqs, polling is used
instead. That has an impact on performance. Some functionality
should not be enabled then. This add a variable in
libertas_priv to indicate that.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
struct cmd_ds_802_11_ps_mode
contains the command header and a pointer to it was
initialized with data points to the body which leads to
mis-interpretation of the cmd_ds_802_11_ps_mode.action member.
cmd[0] contains the header, &cmd[1] points beyond that.
cmdnode->cmdbuf is a pointer to the command buffer
This piece of code was unused since power saving was
not enabled.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of using HT info from beacon IEs, use HT info from
association response frame to update bandwidth in
cfg80211_get_channel handler.
Signed-off-by: Nachiket Kukade <kukaden@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver reads a value from hfa384x_from_bap(), which may fail,
and then assigns the value to a local variable. gcc detects that
in in the failure case, the 'rlen' variable now contains
uninitialized data:
In file included from ../drivers/net/wireless/intersil/hostap/hostap_pci.c:220:0:
drivers/net/wireless/intersil/hostap/hostap_hw.c: In function 'hfa384x_get_rid':
drivers/net/wireless/intersil/hostap/hostap_hw.c:842:5: warning: 'rec' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (le16_to_cpu(rec.len) == 0) {
This restructures the function as suggested by Russell King, to
make it more readable and get more reliable error handling, by
handling each failure mode using a goto.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On a Radxa Rock2 board with a Ampak AP6335 (Broadcom 4339 core) it seems
the card responds very quickly most of the time, unfortunately during
initialisation it sometimes seems to take just a bit over 2 seconds to
respond.
This results intialization failing with message like:
brcmf_c_preinit_dcmds: Retreiving cur_etheraddr failed, -52
brcmf_bus_start: failed: -52
brcmf_sdio_firmware_callback: dongle is not responding
Increasing the timeout to allow for a bit more headroom allows the
card to initialize reliably.
A quick search online after diagnosing/fixing this showed that Google
has a similar patch in their ChromeOS tree, so this doesn't seem
specific to the board I'm using.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Platform NVRAM (stored on a flash partition) has entries separated by a
NULL (\0) char. Our parsing code switches from VALUE state to IDLE
whenever it meets a NULL (\0). When that happens our IDLE handler should
simply consume it and analyze whatever is placed ahead.
This fixes harmless warnings spamming debugging output:
[ 155.165624] brcmfmac: brcmf_nvram_handle_idle warning: ln=1:col=20: ignoring invalid character
[ 155.180806] brcmfmac: brcmf_nvram_handle_idle warning: ln=1:col=44: ignoring invalid character
[ 155.195971] brcmfmac: brcmf_nvram_handle_idle warning: ln=1:col=63: ignoring invalid character
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On Broadcom ARM routers BCM4366 cards are available with 14e4:4365 ID.
Unfortunately this ID was already used by Broadcom for cards with
BCM43142, a totally different chipset requiring SoftMAC driver. To avoid
a conflict between brcmfmac and bcma use more specific ID entry with
subvendor and subdevice specified.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On recent Broadcom chipsets PMU is present as separated core and it
can't be accessed using ChipCommon anymore as it fails with e.g.:
[ 18.198412] Unhandled fault: imprecise external abort (0x1406) at 0xb6da200f
Add a new helper function that will return a proper core that should be
used for accessing PMU registers.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is an extra bitfield with info about some present hardware.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Separated PMU core can be found in new devices and should be used for
accessing PMU registers (which were routed through ChipCommon so far).
This core is one of exceptions that doesn't have or need wrapper address
to be still safely accessible.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far we were looking for address descriptors without a check for
crossing current component border. In case of dealing with unsupported
descriptor or descriptor missing at all the code would incorrectly get
data from another component.
Consider this binary-described component from BCM4366 EROM:
4bf83b01 TAG==CI CID==0x83b
20080201 TAG==CI PORTS==0+1 WRAPPERS==0+1
18400035 TAG==ADDR SZ_SZD TYPE_SLAVE
00050000
18107085 TAG==ADDR SZ_4K TYPE_SWRAP
Driver was assigning invalid base address to this core:
brcmfmac: [6 ] core 0x83b:32 base 0x18109000 wrap 0x18107000
which came from totally different component defined in EROM:
43b36701 TAG==CI CID==0x367
00000201 TAG==CI PORTS==0+1 WRAPPERS==0+0
18109005 TAG==ADDR SZ_4K TYPE_SLAVE
This change will also allow us to support components without wrapper
address in the future.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First of all it changes the way we calculate primary channel offset. If
we use e.g. 80 MHz channel with primary frequency 5180 MHz (which means
center frequency is 5210 MHz) it makes sense to calculate primary offset
as -30 MHz.
Then it fixes values we compare primary_offset with. We were comparing
offset in MHz against -2 or 2 which was resulting in picking a wrong
primary channel.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PMU (Power Management Unit) seems to be a separated piece of hardware,
just accessed using ChipCommon core registers. In recent Broadcom
chipsets PMU is not bounded to CC but available as separated core.
To make code cleaner & easier to review (for a correct R/W access) use
clearer names.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Here's a first batch of patches for 4.6:
* continue the work on multiple Rx queues (Sara)
* add support for beacon storing
used in low power states (Sara)
* cleanups (Rodrigo, Johannes)
* fix the LED behavior for iwldvm (Hubert)
* Use the regular firmware image of WoWLAN (Matti)
* fix 8000 devices for Big Endian machines (Johannes)
* more firmware debug hooks (Golan)
* add support for P2P Client snoozing (Avri)
* make the beacon filtering for AP mode configurable (Andrei)
* fix transmit queues overflow with LSO
Some of the parameter like tx/rx chain mask, number of htt tx desc,
qcache active peer count, etc goes via wmi init cmd to qca4019 firmware
are different.
To make use of 10.4 gen_init function for qca4019, change wmi service
ready handler and 10.4 wmi init functions to adapt qca4019 specific
init values.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add a new entry in hw_params_list for qca4019 with list of
it's own details.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Abstraction layer for vdev subtype is added to solve
subtype mismatch and to give flexible compatibility
among different firmware revisions.
For instance, 10.2 and 10.4 firmware has different
definition of their vdev subtypes for Mesh.
10.4 defined subtype 6 for 802.11s Mesh while 10.2 uses 5.
Hence use the abstraction API to get right subtype to use.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Interface type P2P_GO can be checked by either arvif->vdev_type
and arvif->vdev_subtype or vif->type and vif->p2p.
Use later one to avoid more cpu consumption that could happen
when subtype abstraction layer change is introduced.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update 10.4 WMI service map to sync to the latest 10.4 firmware
as of 1/20/2016.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI_10_4_SERVICE_MESH bit is for non IEEE802.11s Mesh.
Hence rename it to WMI_10_4_SERVICE_MESH_NON_11S.
Also add _11S as post-fix to each of WMI_SERVICE_MESH and
WMI_VDEV_SUBTYPE_MESH specifying the service is for 11s Mesh.
This will help users to distinguish 11s Mesh from non 11s Mesh.
Signed-off-by: Peter Oh <poh@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case there are multiple WMI commands with the same reply_id,
the following scenario can occur:
- Driver sends the first command to the device
- The reply didn’t get on time and there is timeout
- Reply_id, reply_buf and reply_size are set to 0
- Driver sends second wmi command with the same reply_id as the first
- Driver sets wil->reply_id
- Reply for the first wmi command arrives and handled by wmi_recv_cmd
- As its ID fits the reply_id but the reply_buf is not set yet it is
handled as a reply with event handler, and WARN_ON is printed
This patch guarantee atomic setting of all the reply variables and
prevents the above scenario.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211_ops.disconnect() should wait for disconnect flow to
complete. If it does not, internal state becomes out of sync with
one in cfg80211. If one does stress test connect/disconnect
sequence, cfg80211 will issue next connect before disconnect
completed internally.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
wil_tx_vring locks the vring_tx_data lock before accessing the TX
vring to check if it is enabled and valid for use.
In case of quick disconnect / connect events for the same station,
spin_lock(&txdata->lock) can be called during the lock initialization
in the vring init function.
To prevent such a race, the TX vrings spin lock should be initialized
once during wil6210 driver initialization.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Pull networking fixes from David Miller:
"This looks like a lot but it's a mixture of regression fixes as well
as fixes for longer standing issues.
1) Fix on-channel cancellation in mac80211, from Johannes Berg.
2) Handle CHECKSUM_COMPLETE properly in xt_TCPMSS netfilter xtables
module, from Eric Dumazet.
3) Avoid infinite loop in UDP SO_REUSEPORT logic, also from Eric
Dumazet.
4) Avoid a NULL deref if we try to set SO_REUSEPORT after a socket is
bound, from Craig Gallek.
5) GRO key comparisons don't take lightweight tunnels into account,
from Jesse Gross.
6) Fix struct pid leak via SCM credentials in AF_UNIX, from Eric
Dumazet.
7) We need to set the rtnl_link_ops of ipv6 SIT tunnels before we
register them, otherwise the NEWLINK netlink message is missing
the proper attributes. From Thadeu Lima de Souza Cascardo.
8) Several Spectrum chip bug fixes for mlxsw switch driver, from Ido
Schimmel
9) Handle fragments properly in ipv4 easly socket demux, from Eric
Dumazet.
10) Don't ignore the ifindex key specifier on ipv6 output route
lookups, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (128 commits)
tcp: avoid cwnd undo after receiving ECN
irda: fix a potential use-after-free in ircomm_param_request
net: tg3: avoid uninitialized variable warning
net: nb8800: avoid uninitialized variable warning
net: vxge: avoid unused function warnings
net: bgmac: clarify CONFIG_BCMA dependency
net: hp100: remove unnecessary #ifdefs
net: davinci_cpdma: use dma_addr_t for DMA address
ipv6/udp: use sticky pktinfo egress ifindex on connect()
ipv6: enforce flowi6_oif usage in ip6_dst_lookup_tail()
netlink: not trim skb for mmaped socket when dump
vxlan: fix a out of bounds access in __vxlan_find_mac
net: dsa: mv88e6xxx: fix port VLAN maps
fib_trie: Fix shift by 32 in fib_table_lookup
net: moxart: use correct accessors for DMA memory
ipv4: ipconfig: avoid unused ic_proto_used symbol
bnxt_en: Fix crash in bnxt_free_tx_skbs() during tx timeout.
bnxt_en: Exclude rx_drop_pkts hw counter from the stack's rx_dropped counter.
bnxt_en: Ring free response from close path should use completion ring
net_sched: drr: check for NULL pointer in drr_dequeue
...
When in AP mode we need to filter in beacons from other APs to update HT
operation mode. As a power optimization the beacons are filtered out when
there are no associated stations. As a result, when there are no
associated stations, we will not update the HT operation mode until a
station connects.
Add a debugfs parameter that allows to disable this optimization.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Final API of iwl_mpdu_desc has a change in the order of
the fields and does not include energy from the third
antenna (which is perfectly fine, since we don't have one).
Update the structure accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Previous patches enabled new 9000 hardware DMA for one queue
only.
Enable the actual multi-queue path and configuration now.
This requires also per-queue NAPI struct.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
9000 series supports multi-queue rx. The hardware needs
to be configured with the hash functions to perform and
indirection table that maps hash results to the relevant
CPUs\queues.
Support this configuration.
Add debugfs hook to configure the indirection table in
order to enable performance analysis. The configuration
is stateless, receives a partial or full pattern and sends
the command to the firmware.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Decreasing Tx power is allowed only when success ratio is
above the threshold defined in the algorithm. Add this condition.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 9000 hardware introduces the frame releaser, which
keeps track of the aggregation window and notifies host
of the window status. This requires in turn updating
the hardware with the RX BA session window size.
Firmware API was changed to enable that, update the driver
accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It is only called from iwl_mvm_power_set_ba() so simplify things
by removing it.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This member is actually not needed as beacon abort
is only allowed for a bss station.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The MAC address parameters passed to iwl_parse_nvm_data() are passed on
to iwl_set_hw_address_family_8000() which treats them as little endian.
Annotate them as such, and add the missing byte-swapping in mvm.
While at it, add the MAC address to the error to make debugging issues
with it easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Previous patches enabled the multi-queue rx path based on
iwl_mvm_has_new_rx_api() which returned false by default.
Change it to return the actual value based on the firmware
TLV which is now defined.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware will return the baid for BA session in the
ADD_STA command response.
This requires masking the check of the status, which is
actually only 8 bits, and not the whole 32 bits.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
