Add the Rockchip-sepcific dual-dsi setup and hook it into the VOP as well.
As described in the general dual-dsi devicetree binding, the panel should
define two input ports and point each of them to one of the used dsi-
controllers, as well as declare one of them as clock-master.
This is used to determine the dual-dsi state and get access to both
controller instances.
v6:
handle master+slave component in dsi-attach
v5:
use driver-internal mechanism to find dual dsi slave
v4:
add component directly in probe when adding empty dsi slave controller
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-8-heiko@sntech.de
Allow to also drive a slave dw-mipi-dsi controller in a dual-dsi
setup. This will require additional implementation-specific
code to look up the slave instance and do specific setup.
Also will probably need code in the specific crtcs as dual-dsi
does not equal two separate dsi outputs.
To activate, the implementation-specific code should set the slave
using dw_mipi_dsi_set_slave() before calling __dw_mipi_dsi_bind().
v2:
- expect real interface number of lanes
- keep links to both master and slave
v3:
- remove unneeded separate variables
- remove unneeded second slave settings
- disable slave before master
- lane-sum calculation comments
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Philippe Cornu <philippe.cornu@st.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-7-heiko@sntech.de
Add the ROCKCHIP DSI controller driver that uses the Synopsys DesignWare
MIPI DSI host controller bridge and remove the old separate one.
changes:
v2:
add err_pllref, remove unnecessary encoder.enable & disable
correct spelling mistakes
v3:
call dw_mipi_dsi_unbind() in dw_mipi_dsi_rockchip_unbind()
fix typo, use of_device_get_match_data(),
change some bind() logic into probe()
add 'dev_set_drvdata()'
v4:
return -EINVAL when can not get best_freq
add a clarifying comment when get vco
add review tag
v5:
keep our power domain enabled while touching GRF
v6:
change func name dw_mipi_encoder_disable to
dw_mipi_dsi_encoder_disable
v7:
none
v8: Heiko
add Archit's Review tag
adapt to recent changes in the original rockchip-dsi driver
beautify grf-handling
split hw-setup (resources, dsi-host) from bind into probe
v2-new: Heiko
add SPDX header instead of license blurb
drop old versioning to not confuse people
v3-new: Heiko
include ordering
moved hwaccess from mode_set to enable callback
move pllref_clk enablement to bind (needed by bridge mode_set->lane_mbps)
v4-new: Heiko
rebase against recent rockchip-dsi changes
move to call component_add in the new glue host-attach
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-6-heiko@sntech.de
With the regular means of adding the dsi-component in probe it creates
a race condition with the panel probing, as the panel device only gets
created after the dsi-bus got created.
When the panel-driver is build as a module it currently fails hard as the
panel cannot be probed directly:
dw_mipi_dsi_bind()
__dw_mipi_dsi_probe()
creates dsi bus
creates panel device
triggers panel module load
panel not probed (module not loaded or panel probe slow)
drm_bridge_attach
fails with -EINVAL due to empty panel_bridge
Additionally the panel probing can run concurrently with dsi bringup
making it possible that the panel can already be found but dsi-attach
hasn't finished running.
To solve that cleanly we may want to only create the component after
the panel has finished probing, by calling component_add from the
host-attach dsi callback.
As that is specific to glue drivers, add a new struct for host_ops
so that glue drivers can tell the bridge to call specific functions
after the common host-attach and before the common host-detach run.
Suggested-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-4-heiko@sntech.de
__dw_mipi_dsi_probe() does all the grabbing of resources and does it using
devm-helpers. So this is happening on each try of master bringup possibly
slowing down things a lot.
Drivers using the component framework may instead want to call
dw_mipi_dsi_probe separately in their probe function to setup resources
early. That way the dsi bus also gets created earlier and also not
recreated on each bind-try, so that attached panels can load their modules
and be probed way before the bridge-attach in the bind call.
So drop the call to __dw_mipi_dsi_probe and modify the function to take
a struct dw_mipi_dsi instead of the platform-device.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181001123845.11818-3-heiko@sntech.de
Move virtio_gpu_resource_id_{get,put} to virtgpu_object.c and make them
static. Allocate and free the id on creation and destroy, drop all
other calls. That way objects have a valid handle for the whole
lifetime of the object.
Also fixes ids leaking. Worst offender are dumb buffers, and I think
some error paths too.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181019061847.18958-7-kraxel@redhat.com
Track whenever the virtio_gpu_object is already created (i.e. host knows
about it) in a new variable. Add checks to virtio_gpu_object_attach()
to do nothing on objects not created yet.
Make virtio_gpu_ttm_bo_destroy() use the new variable too, instead of
expecting hw_res_handle indicating the object state.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20181019061847.18958-2-kraxel@redhat.com
commit ac657f6461 ("drm/i915: Introduce IS_GEN macro") introduced
GEN_FOREVER that was never used.
My first attempt was to rename it to FOREVER since GEN is
already part of the macro. Then I used coccinelle to change all
-INTEL_GEN(e1) >= e2
+INTEL_GEN_RANGE(e1, e2, FOREVER)
-INTEL_GEN(e1) <= e2
+INTEL_GEN_RANGE(e1, 0, e2)
and I liked it.
However I didn't like very much the remaining
INTEL_GEN(dev_priv) < n
and:
INTEL_GEN(e1) < n
INTEL_GEN_RANGE(e1, 0, n - 1)
didn't make much sense either.
So INTEL_GEN use for > or < seems a better unified way for unlimited
bounds. So, no reason to keep GEN_FOREVER here.
Let's kill before someone start using it.
v2: Remove remaining GEN_FOREVER forgotten in a comment. (Daniel)
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20181026195143.20353-2-rodrigo.vivi@intel.com
As far as I can tell the panel that was added in commit da50bd4258
("drm/panel: simple: Add Innolux TV123WAM panel driver support")
wasn't actually an Innolux TV123WAM but was actually an Innolux
P120ZDG-BF1.
As far as I can tell the Innolux TV123WAM isn't a real panel and but
it's a mosh between the TI TV123WAM and the Innolux P120ZDG-BF1.
Let's unmosh.
Here's my evidence:
* Searching for TV123WAM on the Internet turns up a TI panel. While
it's possible that an Innolux panel has the same model number as the
TI Panel, it seems a little doubtful. Looking up the datasheet from
the TI Panel shows that it's 1920 x 1280 and 259.2 mm x 172.8 mm.
* As far as I know, the patch adding the Innolux Panel was supposed to
be for the board that's sitting in front of me as I type this
(support for that board is not yet upstream). On the back of that
panel I see Innolux P120ZDZ-EZ1 rev B1.
* Someone pointed me at a datasheet that's supposed to be for the
panel in front of me (sorry, I can't share the datasheet). That
datasheet has the string "p120zdg-bf1"
* If I search for "P120ZDG-BF1" on the Internet I get hits for panels
that are 2160x1440. They don't have datasheets, but the fact that
the resolution matches is a good sign.
In any case, let's update the name and also the physical size to match
the correct panel.
Fixes: da50bd4258 ("drm/panel: simple: Add Innolux TV123WAM panel driver support")
Cc: Sandeep Panda <spanda@codeaurora.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-6-dianders@chromium.org
Let's solve the mystery of commit bf1178c989 ("drm/bridge:
ti-sn65dsi86: Add mystery delay to enable()"). Specifically the
reason we needed that mystery delay is that we weren't paying
attention to HPD.
Looking at the datasheet for the same panel that was tested for the
original commit, I see there's a timing "t3" that times from power on
to the aux channel being operational. This time is specced as 0 - 200
ms. The datasheet says that the aux channel is operational at exactly
the same time that HPD is asserted.
Scoping the signals on this board showed that HPD was asserted 84 ms
after power was asserted. That very closely matches the magic 70 ms
delay that we had. ...and actually, in my testing the 70 ms wasn't
quite enough of a delay and some percentage of the time the display
didn't come up until I bumped it to 100 ms (presumably 84 ms would
have worked too).
To solve this, we tried to hook up the HPD signal in the bridge.
...but in doing so we found that that the bridge didn't report that
HPD was asserted until ~280 ms after we powered it (!). This is
explained by looking at the sn65dsi86 datasheet section "8.4.5.1 HPD
(Hot Plug/Unplug Detection)". Reading there we see that the bridge
isn't even intended to report HPD until 100 ms after it's asserted.
...but that would have left us at 184 ms. The extra 100 ms
(presumably) comes from this part in the datasheet:
> The HPD state machine operates off an internal ring oscillator. The
> ring oscillator frequency will vary [ ... ]. The min/max range in
> the HPD State Diagram refers to the possible times based off
> variation in the ring oscillator frequency.
Given that the 280 ms we'll end up delaying if we hook up HPD is
_slower_ than the 200 ms we could just hardcode, for now we'll solve
the problem by just hardcoding a 200 ms delay in the panel driver
using the patch in this series ("drm/panel: simple: Support panels
with HPD where HPD isn't connected").
If we later find a panel that needs to use this bridge where we need
HPD then we'll have to come up with some new code to handle it. Given
the silly debouncing in the bridge chip, though, it seems unlikely.
One last note is that I tried to solve this through another way: In
ti_sn_bridge_enable() I tried to use various combinations of
dp_dpcd_writeb() and dp_dpcd_readb() to detect when the aux channel
was up. In theory that would let me detect _exactly_ when I could
continue and do link training. Unfortunately even if I did an aux
transfer w/out waiting I couldn't see any errors. Possibly I could
keep looping over link training until it came back with success, but
that seemed a little overly hacky to me.
Reviewed-by: Sean Paul <sean@poorly.run>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-4-dianders@chromium.org
Some eDP panels that are designed to be always connected to a board
use their HPD signal to signal that they've finished powering on and
they're ready to be talked to.
However, for various reasons it's possible that the HPD signal from
the panel isn't actually hooked up. In the case where the HPD isn't
hooked up you can look at the timing diagram on the panel datasheet
and insert a delay for the maximum amount of time that the HPD might
take to come up.
Let's add support in simple-panel for this concept.
At the moment we will co-opt the existing "prepare" delay to keep
track of the delay and we'll use a boolean to specify that a given
panel should only apply the delay if the "no-hpd" property was
specified.
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20181025222134.174583-2-dianders@chromium.org
Considering significant number of HDCP specific variables, it will
be clean to have separate struct for HDCP.
New structure called intel_hdcp is added within intel_connector.
v2:
struct hdcp statically allocated. [Sean Paul]
enable and disable function parameters are retained.[Sean Paul]
v3:
No Changes.
v4:
Commit msg is rephrased [Uma]
v5:
Comment for mutex definition.
v6:
hdcp_ prefix from all intel_hdcp members are removed [Sean Paul]
inline function intel_hdcp_to_connector is defined [Sean Paul]
v7:
%s/uint64_t/u64
v8:
Rebased
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540806351-7137-2-git-send-email-ramalingam.c@intel.com
Pull drm updates from Dave Airlie:
"This is going to rebuild more than drm as it adds a new helper to
list.h for doing bulk updates. Seemed like a reasonable addition to
me.
Otherwise the usual merge window stuff lots of i915 and amdgpu, not so
much nouveau, and piles of everything else.
Core:
- Adds a new list.h helper for doing bulk list updates for TTM.
- Don't leak fb address in smem_start to userspace (comes with EXPORT
workaround for people using mali out of tree hacks)
- udmabuf device to turn memfd regions into dma-buf
- Per-plane blend mode property
- ref/unref replacements with get/put
- fbdev conflicting framebuffers code cleaned up
- host-endian format variants
- panel orientation quirk for Acer One 10
bridge:
- TI SN65DSI86 chip support
vkms:
- GEM support.
- Cursor support
amdgpu:
- Merge amdkfd and amdgpu into one module
- CEC over DP AUX support
- Picasso APU support + VCN dynamic powergating
- Raven2 APU support
- Vega20 enablement + kfd support
- ACP powergating improvements
- ABGR/XBGR display support
- VCN jpeg support
- xGMI support
- DC i2c/aux cleanup
- Ycbcr 4:2:0 support
- GPUVM improvements
- Powerplay and powerplay endian fixes
- Display underflow fixes
vmwgfx:
- Move vmwgfx specific TTM code to vmwgfx
- Split out vmwgfx buffer/resource validation code
- Atomic operation rework
bochs:
- use more helpers
- format/byteorder improvements
qxl:
- use more helpers
i915:
- GGTT coherency getparam
- Turn off resource streamer API
- More Icelake enablement + DMC firmware
- Full PPGTT for Ivybridge, Haswell and Valleyview
- DDB distribution based on resolution
- Limited range DP display support
nouveau:
- CEC over DP AUX support
- Initial HDMI 2.0 support
virtio-gpu:
- vmap support for PRIME objects
tegra:
- Initial Tegra194 support
- DMA/IOMMU integration fixes
msm:
- a6xx perf improvements + clock prefix
- GPU preemption optimisations
- a6xx devfreq support
- cursor support
rockchip:
- PX30 support
- rgb output interface support
mediatek:
- HDMI output support on mt2701 and mt7623
rcar-du:
- Interlaced modes on Gen3
- LVDS on R8A77980
- D3 and E3 SoC support
hisilicon:
- misc fixes
mxsfb:
- runtime pm support
sun4i:
- R40 TCON support
- Allwinner A64 support
- R40 HDMI support
omapdrm:
- Driver rework changing display pipeline ordering to use common code
- DMM memory barrier and irq fixes
- Errata workarounds
exynos:
- out-bridge support for LVDS bridge driver
- Samsung 16x16 tiled format support
- Plane alpha and pixel blend mode support
tilcdc:
- suspend/resume update
mali-dp:
- misc updates"
* tag 'drm-next-2018-10-24' of git://anongit.freedesktop.org/drm/drm: (1382 commits)
firmware/dmc/icl: Add missing MODULE_FIRMWARE() for Icelake.
drm/i915/icl: Fix signal_levels
drm/i915/icl: Fix DDI/TC port clk_off bits
drm/i915/icl: create function to identify combophy port
drm/i915/gen9+: Fix initial readout for Y tiled framebuffers
drm/i915: Large page offsets for pread/pwrite
drm/i915/selftests: Disable shrinker across mmap-exhaustion
drm/i915/dp: Link train Fallback on eDP only if fallback link BW can fit panel's native mode
drm/i915: Fix intel_dp_mst_best_encoder()
drm/i915: Skip vcpi allocation for MSTB ports that are gone
drm/i915: Don't unset intel_connector->mst_port
drm/i915: Only reset seqno if actually idle
drm/i915: Use the correct crtc when sanitizing plane mapping
drm/i915: Restore vblank interrupts earlier
drm/i915: Check fb stride against plane max stride
drm/amdgpu/vcn:Fix uninitialized symbol error
drm: panel-orientation-quirks: Add quirk for Acer One 10 (S1003)
drm/amd/amdgpu: Fix debugfs error handling
drm/amdgpu: Update gc_9_0 golden settings.
drm/amd/powerplay: update PPtable with DC BTC and Tvr SocLimit fields
...
Pull VLA removal from Kees Cook:
"Globally warn on VLA use.
This turns on "-Wvla" globally now that the last few trees with their
VLA removals have landed (crypto, block, net, and powerpc).
Arnd mentioned that there may be a couple more VLAs hiding in
hard-to-find randconfigs, but nothing big has shaken out in the last
month or so in linux-next.
We should be basically VLA-free now! Wheee. :)
Summary:
- Remove unused fallback for BUILD_BUG_ON (which technically contains
a VLA)
- Lift -Wvla to the top-level Makefile"
* tag 'vla-v4.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
Makefile: Globally enable VLA warning
compiler.h: give up __compiletime_assert_fallback()
Pull XArray conversion from Matthew Wilcox:
"The XArray provides an improved interface to the radix tree data
structure, providing locking as part of the API, specifying GFP flags
at allocation time, eliminating preloading, less re-walking the tree,
more efficient iterations and not exposing RCU-protected pointers to
its users.
This patch set
1. Introduces the XArray implementation
2. Converts the pagecache to use it
3. Converts memremap to use it
The page cache is the most complex and important user of the radix
tree, so converting it was most important. Converting the memremap
code removes the only other user of the multiorder code, which allows
us to remove the radix tree code that supported it.
I have 40+ followup patches to convert many other users of the radix
tree over to the XArray, but I'd like to get this part in first. The
other conversions haven't been in linux-next and aren't suitable for
applying yet, but you can see them in the xarray-conv branch if you're
interested"
* 'xarray' of git://git.infradead.org/users/willy/linux-dax: (90 commits)
radix tree: Remove multiorder support
radix tree test: Convert multiorder tests to XArray
radix tree tests: Convert item_delete_rcu to XArray
radix tree tests: Convert item_kill_tree to XArray
radix tree tests: Move item_insert_order
radix tree test suite: Remove multiorder benchmarking
radix tree test suite: Remove __item_insert
memremap: Convert to XArray
xarray: Add range store functionality
xarray: Move multiorder_check to in-kernel tests
xarray: Move multiorder_shrink to kernel tests
xarray: Move multiorder account test in-kernel
radix tree test suite: Convert iteration test to XArray
radix tree test suite: Convert tag_tagged_items to XArray
radix tree: Remove radix_tree_clear_tags
radix tree: Remove radix_tree_maybe_preload_order
radix tree: Remove split/join code
radix tree: Remove radix_tree_update_node_t
page cache: Finish XArray conversion
dax: Convert page fault handlers to XArray
...
