This patch adds helpers for calculating the maximum compressed BPP
supported with small joiner.
This also adds a helper for calculating the slice count in case
of small joiner.
These are inside intel_dp since they take into account hardware
limitations.
v6:
* Take mode_clock and mode_hdisplay as input arguments
so that this can be called in intel_dp_mode_valid (Manasi)
v5:
* Get the max slice width from DPCD
* Check against Min_Slice_width of 2560 (Anusha)
v4:
* #defines for PPR in slice count helper (Gaurav)
v3:
* Simply logic for bpp (DK)
* Limit the valid slice count by max supported by Sink (Manasi)
v2:
* Change the small joiner RAM buffer constant as bspec changed (Manasi)
* rename it as SMALL_JOINER since we are not enabling
big joiner yet (Anusha)
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-5-manasi.d.navare@intel.com
DSC is supported on eDP starting GEN 10 display (on GLK) and on DP starting
GEN 11.
This patch implements the discovery phase of DSC. On hotplug,
source reads the DSC DPCD register set (0x00060 - 0x0006F) to
read the decompression capabilities of the sink device.
This entire block of registers is cached in intel_dp so that
capability information can be used during DSC configuration
phase during compute_config phase of the modeset.
For eDP, this caching happens during the eDP initialization.
This caching is done only for eDP and DP rev >= 1.4
v5:
* Fix the block comment (Gaurav)
* Fix the commit message DSC DPCD addresses (Gaurav)
* Use DRM_ERROR for dpcd_read fail (Gaurav,Anusha)
v4:
* Cache these only for Gen >= 11
v3:
* Remove the dsc_sink_support field in intel_dp (Jani N)
v2:
* Clear the cached registers on hotplug always (Jani N)
* Combine the eDP and DP caching in same function (Jani N)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181031001923.31442-3-manasi.d.navare@intel.com
ICL supports DC5, DC6, and DC9. Enable DC9 during screen-off, and enable
DC5/6 when appropriate.
v2: (James Ausmus)
- Also handle ICL as GEN9_LP in i915_drm_suspend_late and
i915_drm_suspend_early
- Add DC9 to gen9_dc_mask for ICL
- Re-order GEN checks for newest platform first
- Use INTEL_GEN instead of INTEL_INFO->gen
- Use INTEL_GEN >= 11 instead of IS_ICELAKE
- Consolidate GEN checks
v3: (James Ausmus)
- Also allow DC6 for ICL (Imre, Art)
- Simplify !(GEN >= 11) to GEN < 11 (Imre)
v4: (James Ausmus)
- Don't call intel_power_sequencer_reset after DC9 for Gen11+, as the
PPS regs are Always On
- Rebase against upstream changes
v5: (Anusha Srivatsa)
- rebased against the latest upstream changes.
v6: (Anusha Srivatsa)
- rebased.Use INTEL_GEN consistently.
- Simplify the code (Rodrigo)
v7: rebased. Change order according to platforms(Jyoti)
v8: rebased. Change the check from platform specific to
HAS_PCH_SPLIT(). Add comment in code to be more clear.(Rodrigo)
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Signed-off-by: James Ausmus <james.ausmus@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Tested-by: Jyoti Yadav <jyoti.r.yadav@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181029221410.4423-1-anusha.srivatsa@intel.com
Considering significant number of HDCP specific variables, it will
be clean to have separate struct for HDCP.
New structure called intel_hdcp is added within intel_connector.
v2:
struct hdcp statically allocated. [Sean Paul]
enable and disable function parameters are retained.[Sean Paul]
v3:
No Changes.
v4:
Commit msg is rephrased [Uma]
v5:
Comment for mutex definition.
v6:
hdcp_ prefix from all intel_hdcp members are removed [Sean Paul]
inline function intel_hdcp_to_connector is defined [Sean Paul]
v7:
%s/uint64_t/u64
v8:
Rebased
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1540806351-7137-2-git-send-email-ramalingam.c@intel.com
The first 3 planes (primary, sprite 0 and 1) have a dedicated chroma
upsampler to upscale YUV420 to YUV444 and the scaler should only be
used for upscaling. Because of this we shouldn't program the scalers
in planar mode if NV12 and the chroma upsampler are used. Instead
program the scalers like on normal planes.
Sprite 2 and 3 have no dedicated scaler, and need to program the
selected Y plane in the scaler mode.
Changes since v1:
- Make the comment less confusing.
Changes since v2:
- Fix checkpatch warning (Matt)
- gen10- -> Pre-gen11 (Ville)
- PS_SCALER_MODE_PACKED -> PS_SCALER_MODE_NORMAL. (Matt)
- Add comment about scaler mode in intel_atomic_setup_scaler(). (Matt)
- Rename need_scaling to need_scaler. (Matt)
- Move the crtc need_scaling check to skl_update_scaler_crtc().
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181018115134.9061-6-maarten.lankhorst@linux.intel.com
To make NV12 working on icl, we need to update 2 planes simultaneously.
I've chosen to do this in the CRTC step after plane validation is done,
so we know what planes are (in)visible. The linked Y plane will get
updated in intel_plane_update_planes_on_crtc(), by the call to
update_slave, which gets the master's plane_state as argument.
The link requires both planes for atomic_update to work,
so make sure skl_ddb_add_affected_planes() adds both states.
Changes since v1:
- Introduce icl_is_nv12_y_plane(), instead of hardcoding sprite numbers.
- Put all the state updating login in intel_plane_atomic_check_with_state().
- Clean up changes in intel_plane_atomic_check().
Changes since v2:
- Fix intel_atomic_get_old_plane_state() to actually return old state.
- Move visibility changes to preparation patch.
- Only try to find a Y plane on gen11, earlier platforms only require
a single plane.
Changes since v3:
- Fix checkpatch warning about to_intel_crtc() usage.
- Add affected planes from icl_add_linked_planes() before check_planes(),
it's a cleaner way to do this. (Ville)
Changes since v4:
- Clear plane links in icl_check_nv12_planes() for clarity.
- Only pass crtc_state to icl_check_nv12_planes().
- Use for_each_new_intel_plane_in_state() in icl_check_nv12_planes.
- Rename aux to linked. (Ville)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181022135152.15324-1-maarten.lankhorst@linux.intel.com
[mlankhorst: Change bool slave to u32, to satisfy checkpatch]
[mlankhorst: Add WARN_ON's based on Ville's suggestion]
LSPCON chips can generate YCBCR outputs, if asked nicely :).
In order to generate YCBCR 4:2:0 outputs, a source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:2:0 in AVI infoframes
Whereas for YCBCR 4:4:4 outputs, the source must:
- send YCBCR 4:4:4 signals to LSPCON
- program color space as 4:4:4 in AVI infoframes
So for both 4:2:0 as well as 4:4:4 outputs, we are driving the
pipe for YCBCR 4:4:4 output, but AVI infoframe's color space
information indicates LSPCON FW to start scaling down from YCBCR
4:4:4 and generate YCBCR 4:2:0 output. As the scaling is done by
LSPCON device, we need not to reserve a scaler for 4:2:0 outputs.
V2: rebase
V3: Addressed review comments from Ville
- add enum crtc_output_format instead of bool ycbcr420
- use crtc_output_format=4:4:4 for modeset of LSPCON 4:2:0 output
cases in this way we will have YCBCR 4:4:4 framework ready (except
the ABI part)
V4: Added r-b from Maarten (for v3)
Addressed review comments from Ville:
- Do not add a non-atomic state variable to determine lspcon output.
Instead add bool in CRTC state to indicate lspcon based scaling.
V5: Addressed review comments from Ville:
- Change the state bool name from external scaling to something more
relavent.
- Keep the info and adjusted_mode structures const.
- use crtc_state instead of pipe_config.
- Push all the config change into lspcon_ycbcr420_config function.
V6: Rebase, small changes to accommodate changes in patch 2.
V7: Fixed checkpatch warnings for alignment
V8: Rebase
PS: Ignored following warnings to match the current formatting:
drm/i915: Add YCBCR 4:2:0/4:4:4 support for LSPCON
-:53: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#53: FILE: drivers/gpu/drm/i915/i915_reg.h:8721:
+#define TRANS_MSA_SAMPLING_444 (2<<1)
^
-:54: CHECK:SPACING: spaces preferred around that '<<' (ctx:VxV)
#54: FILE: drivers/gpu/drm/i915/i915_reg.h:8722:
+#define TRANS_MSA_CLRSP_YCBCR (2<<3)
V9: Rebase
V10: Rebase
V11: Rebase
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-8-git-send-email-shashank.sharma@intel.com
In order to pass AVI infoframes to LSPCON devices, a source has to
write them in a vendor recommended method and location.
This patch series:
- adds generic LSPCON infoframe setup functions.
- registers these functions into existing AVI infoframe framework.
- triggers these functions from modeset sequence.
Next patches in the series will add vendor specific code.
V2: Added new parameter to align with new definition of
drm_hdmi_avi_infoframe_quant_range
V3: Added r-b from Maarten (for V2)
Added new parameter output_format in struct lspcon to accommodate
Ville's review comments on last patch of the series
V4: Addressed Ville's review comment
- Do not add output_format in LSPCON state, as its non-atomic. Add
this into CRTC state (added in a later patch).
V5: Rebase
V6: Rebase
V7: Rebase
V8: Rebase
V9: Rebase
V10: Rebase
V11: Accommodated rebasing changes in intel_git_port fptrs (set_infoframes and infoframe_enabled)
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-5-git-send-email-shashank.sharma@intel.com
This patch adds support for YCBCR 4:4:4 CRTC output format.
To do this, this patch extends the existing YCBCR 4:2:0
framework by:
- Adding new parameter in for YCBCR 4:4:4 enum crtc_iutput_format.
- Adding case for YCBCR 4:4:4 in while setting AVI infoframes.
- Adding necessary checks in modeset sequence.
V3: Added this patch in the series
V4: Added r-b from Maarten (for v3)
Addressed review comment from Ville:
Do not use (config->output_format > CRTC_OUTPUT_RGB)
V5: Rebase
V6: Rebase and small change, to accommodate changes in patch 2
V7: Fixed checkpatch alignment warnings
V8: Rebase
V9: Rebase
V10: Rebase
V11: Addressed review comment from Ville
Missing output_format_str[INTEL_OUTPUT_FORMAT_YCBCR444]
Added Ville's R-B.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-3-git-send-email-shashank.sharma@intel.com
Currently, we are using a bool in CRTC state (state->ycbcr420),
to indicate modeset, that the output format is YCBCR 4:2:0. Now in
order to support other YCBCR formats, we will need more such flags.
This patch adds a new enum parameter for YCBCR 4:2:0 outputs, in the
CRTC output formats and then plugs it during the modeset.
V3: Added this patch in the series, to address review comments from
second patchset.
V4: Added r-b from Maarten (on v3)
Addressed review comments from Ville:
- Change the enum name to intel_output_format.
- Start the enum value (INVALID) from 0 instaed of 1.
- Set the crtc's output_format to RGB in encoder's compute_config.
V5: Broke previous patch 1 into two parts,
- first patch to add CRTC output format in general
- second patch (this one) to add YCBCR 4:2:0 output
format specifically.
- Use ARRAY_SIZE(format_str) for output format validity check (Ville)
V6: Added a separate function to calculate crtc_state->output_format, and
calling it from various get_config function (Fix CI build warning)
V7: Fixed checkpatch warnings for alignment
V8: Rebase
V9: Rebase
V10: Rebase
V11: Addressed review comments from Ville:
- Change check for CRTC output format from > ARRAY_SIZE to >= ARRAY_SIZE.
- Check for values < INTEL_OUTPUT_FORMAT_RGB is unnecessary.
- No need to get CRTC YCBCR config, for pre-BDW functions.
Added Ville's r-b.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-2-git-send-email-shashank.sharma@intel.com
This patch adds an enum "intel_output_format" to represent
the output format of a particular CRTC. This enum will be
used to produce a RGB/YCBCR4:4:4/YCBCR4:2:0 output format
during the atomic modeset calculations.
V5:
- Created this separate patch to introduce and init output_format.
- Initialize parameters of output_format_str respectively (Jani N).
- Call it intel_output_format than crtc_output_format(Ville).
- Set output format in pipe_config for every encoder (Ville).
- Get rid of extra DRM_DEBUG_KMS during get_pipe_config (Ville)
V6: Rebase
V7: Fixed alignment warnings (checkpatch)
V8: Another check[atch warning for alignment
V9: Rebase
V10: Rebase on top of DSI restructure
V11: Addressed review comment from Ville
- Set CRTC format for pre-HSW get_pipe_config() function too.
Added Ville's R-B
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1539325394-20788-1-git-send-email-shashank.sharma@intel.com
There's not much point in following the primary vs. sprite split
for the SKL+ universal plane init code. The only difference is
of our own doing in the form of the .check_plane(). Let's make
a small exception for that little detail and otherwise share
the same code to initialize all the universal planes.
Eventually we should eliminate the mess around .check_plane()
as well, but for now let's be happy with some code reduction.
v2: Remember to set up plane->has_fbc
Make skl_plane_has_ccs() static
v3: Rebase due to NV12, rename some variables
v4: Don't leave the color_encoding/range props behind
v5: Rebase dur to blend properties, skl_plane_max_stride() and
skl_plane_check()
v6: Make skl_update_plane() static
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com> #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20181005125817.22576-10-ville.syrjala@linux.intel.com
commit 4e0b83a567 ("drm/i915: Extract per-platform plane->check()
functions") removed the plane max stride check for sprite planes.
I was going to add it back when introducing GTT remapping for the
display, but after further thought it seems better to re-introduce
it separately.
So let's add the max stride check back. And let's do it in a nicer
form than what we had before and do it for all plane types (easy
now that we have the ->max_stride() plane vfunc).
Only sprite planes really need this for now since primary planes
are capable of scanning out the current max fb size we allow, and
cursors have more stringent stride checks elsewhere.
Cc: José Roberto de Souza <jose.souza@intel.com>
Fixes: 4e0b83a567 ("drm/i915: Extract per-platform plane->check() functions")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180918140243.12207-1-ville.syrjala@linux.intel.com
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
drm_atomic_helper_commit_planes_on_crtc calls begin_commit,
then plane_update hooks, then flush_commit. Because we keep our own
visibility tracking through plane_state->visible there's no need to
rely on the atomic hooks for this.
By explicitly writing our own helper, we can update visible planes
as needed, which is useful to make NV12 support work as intended.
Changes since v1:
- Reword commit message. (Matt Roper)
- Rename to intel_update_planes_on_crtc(). (Matt)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180920102711.4184-6-maarten.lankhorst@linux.intel.com
Split up intel_check_primary_plane() and intel_check_sprite_plane()
into per-platform variants. This way we can get a unified behaviour
between the SKL universal planes, and we stop checking for non-SKL
specific scaling limits for the "sprite" planes. And we now get
a natural place where to add more plarform specific checks.
v2: Split the .check_plane() calling convention change out (José)
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180907152413.15761-10-ville.syrjala@linux.intel.com
Let's store the final plane stride in the plane state. This avoids
having to pick between the normal vs. rotated stride during hardware
programming. And once we get GTT remapping the plane stride will
no longer match the fb stride so we'll need a place to store it
anyway.
v2: Keep checking fb->pitches[0] for cursor as later on we won't
populate plane_state->color_plane[0].stride for invisible planes
and we have been checking the cursor fb stride even for invisible
planes
v3: s/betwen/between in commit msg (José)
v4: Check color_plane[0].stride instead of fb->pitches[0] in
the skl_check_main_surface() X-tiling kludge
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180911150139.23922-1-ville.syrjala@linux.intel.com
