The R40 HDMI PHY seems to be different to the A64 one, the A64 one
has no input mux, but the R40 one has.
Drop the A64 fallback compatible from the HDMI PHY node in R40 DT.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[wens@csie.org: Fix subject prefix order]
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Add KVM_CAP_MSR_PLATFORM_INFO so that userspace can disable guest access
to reads of MSR_PLATFORM_INFO.
Disabling access to reads of this MSR gives userspace the control to "expose"
this platform-dependent information to guests in a clear way. As it exists
today, guests that read this MSR would get unpopulated information if userspace
hadn't already set it (and prior to this patch series, only the CPUID faulting
information could have been populated). This existing interface could be
confusing if guests don't handle the potential for incorrect/incomplete
information gracefully (e.g. zero reported for base frequency).
Signed-off-by: Drew Schmitt <dasch@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Allow userspace to set turbo bits in MSR_PLATFORM_INFO. Previously, only
the CPUID faulting bit was settable. But now any bit in
MSR_PLATFORM_INFO would be settable. This can be used, for example, to
convey frequency information about the platform on which the guest is
running.
Signed-off-by: Drew Schmitt <dasch@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to section "Checks on VMX Controls" in Intel SDM vol 3C, the
following check needs to be enforced on vmentry of L2 guests:
If the 'enable VPID' VM-execution control is 1, the value of the
of the VPID VM-execution control field must not be 0000H.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
According to section "Checks on VMX Controls" in Intel SDM vol 3C,
the following check needs to be enforced on vmentry of L2 guests:
- Bits 5:0 of the posted-interrupt descriptor address are all 0.
- The posted-interrupt descriptor address does not set any bits
beyond the processor's physical-address width.
Signed-off-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Mark Kanda <mark.kanda@oracle.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Reviewed-by: Karl Heubaum <karl.heubaum@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In case L1 do not intercept L2 HLT or enter L2 in HLT activity-state,
it is possible for a vCPU to be blocked while it is in guest-mode.
According to Intel SDM 26.6.5 Interrupt-Window Exiting and
Virtual-Interrupt Delivery: "These events wake the logical processor
if it just entered the HLT state because of a VM entry".
Therefore, if L1 enters L2 in HLT activity-state and L2 has a pending
deliverable interrupt in vmcs12->guest_intr_status.RVI, then the vCPU
should be waken from the HLT state and injected with the interrupt.
In addition, if while the vCPU is blocked (while it is in guest-mode),
it receives a nested posted-interrupt, then the vCPU should also be
waken and injected with the posted interrupt.
To handle these cases, this patch enhances kvm_vcpu_has_events() to also
check if there is a pending interrupt in L2 virtual APICv provided by
L1. That is, it evaluates if there is a pending virtual interrupt for L2
by checking RVI[7:4] > VPPR[7:4] as specified in Intel SDM 29.2.1
Evaluation of Pending Interrupts.
Note that this also handles the case of nested posted-interrupt by the
fact RVI is updated in vmx_complete_nested_posted_interrupt() which is
called from kvm_vcpu_check_block() -> kvm_arch_vcpu_runnable() ->
kvm_vcpu_running() -> vmx_check_nested_events() ->
vmx_complete_nested_posted_interrupt().
Reviewed-by: Nikita Leshenko <nikita.leshchenko@oracle.com>
Reviewed-by: Darren Kenny <darren.kenny@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
VMX cannot be enabled under SMM, check it when CR4 is set and when nested
virtualization state is restored.
This should fix some WARNs reported by syzkaller, mostly around
alloc_shadow_vmcs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The functions
kvm_load_guest_fpu()
kvm_put_guest_fpu()
are only used locally, make them static. This requires also that both
functions are moved because they are used before their implementation.
Those functions were exported (via EXPORT_SYMBOL) before commit
e5bb40251a ("KVM: Drop kvm_{load,put}_guest_fpu() exports").
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
These structures are going to be used from KVM code so let's make
their names reflect their Hyper-V origin.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A VMX preemption timer value of '0' is guaranteed to cause a VMExit
prior to the CPU executing any instructions in the guest. Use the
preemption timer (if it's supported) to trigger immediate VMExit
in place of the current method of sending a self-IPI. This ensures
that pending VMExit injection to L1 occurs prior to executing any
instructions in the guest (regardless of nesting level).
When deferring VMExit injection, KVM generates an immediate VMExit
from the (possibly nested) guest by sending itself an IPI. Because
hardware interrupts are blocked prior to VMEnter and are unblocked
(in hardware) after VMEnter, this results in taking a VMExit(INTR)
before any guest instruction is executed. But, as this approach
relies on the IPI being received before VMEnter executes, it only
works as intended when KVM is running as L0. Because there are no
architectural guarantees regarding when IPIs are delivered, when
running nested the INTR may "arrive" long after L2 is running e.g.
L0 KVM doesn't force an immediate switch to L1 to deliver an INTR.
For the most part, this unintended delay is not an issue since the
events being injected to L1 also do not have architectural guarantees
regarding their timing. The notable exception is the VMX preemption
timer[1], which is architecturally guaranteed to cause a VMExit prior
to executing any instructions in the guest if the timer value is '0'
at VMEnter. Specifically, the delay in injecting the VMExit causes
the preemption timer KVM unit test to fail when run in a nested guest.
Note: this approach is viable even on CPUs with a broken preemption
timer, as broken in this context only means the timer counts at the
wrong rate. There are no known errata affecting timer value of '0'.
[1] I/O SMIs also have guarantees on when they arrive, but I have
no idea if/how those are emulated in KVM.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
[Use a hook for SVM instead of leaving the default in x86.c - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Provide a singular location where the VMX preemption timer bit is
set/cleared so that future usages of the preemption timer can ensure
the VMCS bit is up-to-date without having to modify unrelated code
paths. For example, the preemption timer can be used to force an
immediate VMExit. Cache the status of the timer to avoid redundant
VMREAD and VMWRITE, e.g. if the timer stays armed across multiple
VMEnters/VMExits.
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
A VMX preemption timer value of '0' at the time of VMEnter is
architecturally guaranteed to cause a VMExit prior to the CPU
executing any instructions in the guest. This architectural
definition is in place to ensure that a previously expired timer
is correctly recognized by the CPU as it is possible for the timer
to reach zero and not trigger a VMexit due to a higher priority
VMExit being signalled instead, e.g. a pending #DB that morphs into
a VMExit.
Whether by design or coincidence, commit f4124500c2 ("KVM: nVMX:
Fully emulate preemption timer") special cased timer values of '0'
and '1' to ensure prompt delivery of the VMExit. Unlike '0', a
timer value of '1' has no has no architectural guarantees regarding
when it is delivered.
Modify the timer emulation to trigger immediate VMExit if and only
if the timer value is '0', and document precisely why '0' is special.
Do this even if calibration of the virtual TSC failed, i.e. VMExit
will occur immediately regardless of the frequency of the timer.
Making only '0' a special case gives KVM leeway to be more aggressive
in ensuring the VMExit is injected prior to executing instructions in
the nested guest, and also eliminates any ambiguity as to why '1' is
a special case, e.g. why wasn't the threshold for a "short timeout"
set to 10, 100, 1000, etc...
Signed-off-by: Sean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm_commit_zap_page() has been renamed to kvm_mmu_commit_zap_page()
This patch is to fix the commit.
Signed-off-by: Lan Tianyu <Tianyu.Lan@microsoft.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Here is the code path which shows kvm_mmu_setup() is invoked after
kvm_mmu_create(). Since kvm_mmu_setup() is only invoked in this code path,
this means the root_hpa and prev_roots are guaranteed to be invalid. And
it is not necessary to reset it again.
kvm_vm_ioctl_create_vcpu()
kvm_arch_vcpu_create()
vmx_create_vcpu()
kvm_vcpu_init()
kvm_arch_vcpu_init()
kvm_mmu_create()
kvm_arch_vcpu_setup()
kvm_mmu_setup()
kvm_init_mmu()
This patch set reset_roots to false in kmv_mmu_setup().
Fixes: 50c28f21d0
Signed-off-by: Wei Yang <richard.weiyang@gmail.com>
Reviewed-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
kvm should not attempt to read guest PDPTEs when CR0.PG = 0 and
CR4.PAE = 1.
Signed-off-by: Junaid Shahid <junaids@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
When VMX is used with flexpriority disabled (because of no support or
if disabled with module parameter) MMIO interface to lAPIC is still
available in x2APIC mode while it shouldn't be (kvm-unit-tests):
PASS: apic_disable: Local apic enabled in x2APIC mode
PASS: apic_disable: CPUID.1H:EDX.APIC[bit 9] is set
FAIL: apic_disable: *0xfee00030: 50014
The issue appears because we basically do nothing while switching to
x2APIC mode when APIC access page is not used. apic_mmio_{read,write}
only check if lAPIC is disabled before proceeding to actual write.
When APIC access is virtualized we correctly manipulate with VMX controls
in vmx_set_virtual_apic_mode() and we don't get vmexits from memory writes
in x2APIC mode so there's no issue.
Disabling MMIO interface seems to be easy. The question is: what do we
do with these reads and writes? If we add apic_x2apic_mode() check to
apic_mmio_in_range() and return -EOPNOTSUPP these reads and writes will
go to userspace. When lAPIC is in kernel, Qemu uses this interface to
inject MSIs only (see kvm_apic_mem_write() in hw/i386/kvm/apic.c). This
somehow works with disabled lAPIC but when we're in xAPIC mode we will
get a real injected MSI from every write to lAPIC. Not good.
The simplest solution seems to be to just ignore writes to the region
and return ~0 for all reads when we're in x2APIC mode. This is what this
patch does. However, this approach is inconsistent with what currently
happens when flexpriority is enabled: we allocate APIC access page and
create KVM memory region so in x2APIC modes all reads and writes go to
this pre-allocated page which is, btw, the same for all vCPUs.
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
There's no need to treat mismatched cache-line sizes reported by CTR_EL0
differently to any other mismatched fields that we treat as "STRICT" in
the cpufeature code. In both cases we need to trap and emulate EL0
accesses to the register, so drop ARM64_MISMATCHED_CACHE_LINE_SIZE and
rely on ARM64_MISMATCHED_CACHE_TYPE instead.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
[catalin.marinas@arm.com: move ARM64_HAS_CNP in the empty cpucaps.h slot]
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fix wrong usage of pr_info introduced by the commit e728e4f201 ("ARM:
s3c24xx: formatting cleanup in mach-mini2440.c").
Since the idea is to print on a single line, pr_cont has to be used.
Signed-off-by: Cedric Roux <sed@free.fr>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
dtc has new checks for I2C and SPI buses. Fix the warnings in node names
and unit-addresses.
arch/arm/boot/dts/at91-dvk_som60.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/eeprom@87: I2C bus unit address format error, expected "57"
arch/arm/boot/dts/at91-dvk_som60.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f0018000/ft5426@56: I2C bus unit address format error, expected "38"
arch/arm/boot/dts/at91-vinco.dtb: Warning (i2c_bus_reg): /ahb/apb/i2c@f8024000/rtc@64: I2C bus unit address format error, expected "32"
arch/arm/boot/dts/at91sam9260ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9g20ek_2mmc.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9g20ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/mtd_dataflash@0: SPI bus unit address format error, expected "1"
arch/arm/boot/dts/at91sam9261ek.dtb: Warning (spi_bus_reg): /ahb/apb/spi@fffc8000/tsc2046@0: SPI bus unit address format error, expected "2"
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Add devicetree support for HiKey970 development board which
based on Hi3670 SoC and is also one of the 96Boards Consumer
Edition and AI platform.
Only UART6 is enabled which is the default console required
by the 96Boards Consumer Edition Specification.
This patch has been tested on HiKey970 Board.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Add initial devicetree support for Hisilicon Hi3670 SoC which
is similar to Hi3660 SoC with NPU support.
This SoC has Octal core BigLittle CPUs in two clusters(4 * A53 & 4 * A73).
Only UART6 has been added for console support which is
pre configured by the bootloader. A fixed clock is sourcing
the UART6 which will get replaced by the clock driver when available.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The clocks property should either be present for all the CPUs of a
cluster or none. If these are present only for a subset of CPUs of a
cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add missing clocks property.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
The code for conditionally printing unhanded signals is duplicated twice
in arch/x86/kernel/traps.c. Factor it out into it's own subroutine
called show_signal to make the code clearer and easier to maintain.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This separates the logic of generating the signal from the logic of
gathering the information about the bounds violation.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The value passed in to addr_referenced is of type void __user *, so update
the addr_referenced parameter in trace_mpx_bounds_register_exception to match.
Also update the addr_referenced paramater in TP_STRUCT__entry as it again
holdes the same value.
I don't know why this was missed earlier but sparse was complaining when
testing test branch so fix this now.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This simplifies the code making it clearer what is going on.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Only the call from do_sigbus will send SIGBUS due to a memory machine
check error. Consolidate all of the machine check signal generation
code in do_sigbus and remove the now unnecessary fault parameter from
force_sig_info_fault.
Explicitly use the now constant si_code BUS_ADRERR in the call
to force_sig_info_fault from do_sigbus.
This makes the code in arch/x86/mm/fault.c easier to follower and
simpler to maintain.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
The function fill_sigtrap_info now only has one caller so remove
it and put it's contents in it's caller.
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace user_single_step_siginfo with user_single_step_report
that allocates siginfo structure on the stack and sends it.
This allows tracehook_report_syscall_exit to become a simple
if statement that calls user_single_step_report or ptrace_report_syscall
depending on the value of step.
Update the default helper function now called user_single_step_report
to explicitly set si_code to SI_USER and to set si_uid and si_pid to 0.
The default helper has always been doing this (using memset) but it
was far from obvious.
The powerpc helper can now just call force_sig_fault.
The x86 helper can now just call send_sigtrap.
Unfortunately the default implementation of user_single_step_report
can not use force_sig_fault as it does not use a SIGTRAP si_code.
So it has to carefully setup the siginfo and use use force_sig_info.
The net result is code that is easier to understand and simpler
to maintain.
Ref: 85ec7fd9f8 ("ptrace: introduce user_single_step_siginfo() helper")
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Firmware-Assisted Dump (FADump) needs to be registered again after any
memory hot add/remove operation to update the crash memory ranges. But
currently, the kernel returns '-EEXIST' if we try to register without
uregistering it first. This could expose the system to racing issues
while unregistering and registering FADump from userspace during udev
events. Spare the userspace of this and let it be taken care of in the
kernel space for a simpler interface.
Since this change, running 'echo 1 > /sys/kernel/fadump_registered'
would result in re-regisering (unregistering and registering) FADump,
if it was already registered.
Signed-off-by: Hari Bathini <hbathini@linux.ibm.com>
Acked-by: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In lparcfg_write we hard code kbuf_sz and then use this as the variable
length of kbuf creating a variable length array. Since we're hard coding
the length anyway just define the array using this as the length and
remove the need for kbuf_sz, thus removing the variable length array.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
In prom_check_platform_support() we retrieve and parse the
"ibm,arch-vec-5-platform-support" property of the chosen node.
Currently we use a variable length array however to avoid this use an
array of constant length 8.
This property is used to indicate the supported options of vector 5
bytes 23-26 of the ibm,architecture.vec node. Each of these options
is a pair of bytes, thus for 4 options we have a max length of 8 bytes.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
This re-applies commit b91c1e3e7a ("powerpc: Fix duplicate const
clang warning in user access code") (Jun 2015) which was undone in
commits:
f2ca809059 ("powerpc/sparse: Constify the address pointer in __get_user_nosleep()") (Feb 2017)
d466f6c5ca ("powerpc/sparse: Constify the address pointer in __get_user_nocheck()") (Feb 2017)
f84ed59a61 ("powerpc/sparse: Constify the address pointer in __get_user_check()") (Feb 2017)
We see a large number of duplicate const errors in the user access
code when building with llvm/clang:
include/linux/pagemap.h:576:8: warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
ret = __get_user(c, uaddr);
The problem is we are doing const __typeof__(*(ptr)), which will hit
the warning if ptr is marked const.
Removing const does not seem to have any effect on GCC code
generation.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When building with clang crt0's _zimage_start is not marked weak, which
breaks the build when linking the kernel image:
$ objdump -t arch/powerpc/boot/crt0.o |grep _zimage_start$
0000000000000058 g .text 0000000000000000 _zimage_start
ld: arch/powerpc/boot/wrapper.a(crt0.o): in function '_zimage_start':
(.text+0x58): multiple definition of '_zimage_start';
arch/powerpc/boot/pseries-head.o:(.text+0x0): first defined here
Clang requires the .weak directive to appear after the symbol is
declared. The binutils manual says:
This directive sets the weak attribute on the comma separated list of
symbol names. If the symbols do not already exist, they will be
created.
So it appears this is different with clang. The only reference I could
see for this was an OpenBSD mailing list post[1].
Changing it to be after the declaration fixes building with Clang, and
still works with GCC.
$ objdump -t arch/powerpc/boot/crt0.o |grep _zimage_start$
0000000000000058 w .text 0000000000000000 _zimage_start
Reported to clang as https://bugs.llvm.org/show_bug.cgi?id=38921
[1] https://groups.google.com/forum/#!topic/fa.openbsd.tech/PAgKKen2YCY
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Disable new features from recent releases, and clean out some other
unused options:
- Enable EXPERT, so we can disable some things
- Disable non-powerpc BPF decoders
- Disable TASKSTATS
- Disable unused syscalls
- Set more things to be modules
- Turn off unused network vendors
- PPC_OF_BOOT_TRAMPOLINE and FB_OF are unused on powernv
- Drop unused Radeon and Matrox GPU drivers
- IPV6 support landed in petitboot
- Bringup related command line powersave=off dropped, switch to quiet
Set CONFIG_I2C_CHARDEV=y as the module is not loaded automatically, and
without this i2cget etc. will fail in the skiroot environment.
This defconfig gets us build coverage of KERNEL_XZ, which was broken in
the 4.19 merge window for powerpc.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
When performing partition migrations all present CPUs must be online
as all present CPUs must make the H_JOIN call as part of the migration
process. Once all present CPUs make the H_JOIN call, one CPU is returned
to make the rtas call to perform the migration to the destination system.
During testing of migration and changing the SMT state we have found
instances where CPUs are offlined, as part of the SMT state change,
before they make the H_JOIN call. This results in a hung system where
every CPU is either in H_JOIN or offline.
To prevent this this patch disables CPU hotplug during the migration
process.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
There are three instances in which dlpar hotplug events are invoked;
handling a hotplug interrupt (in a kvm guest), handling a dlpar
request through sysfs, and updating LMB affinity when handling a
PRRN event. Only in the case of handling a hotplug interrupt do we
have to put the work on a workqueue, the other cases can handle the
dlpar request directly.
This patch exports the handle_dlpar_errorlog() function so that
dlpar hotplug events can be handled directly and updates the two
instances mentioned above to use the direct invocation.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The updates to powerpc numa and memory hotplug code now use the
in-kernel LMB array instead of the device tree. This change allows the
pseries memory DLPAR code to only update the device tree once after
successfully handling a DLPAR request.
Prior to the in-kernel LMB array, the numa code looked up the affinity
for memory being added in the device tree, the code now looks this up
in the LMB array. This change means the memory hotplug code can just
update the affinity for an LMB in the LMB array instead of updating
the device tree.
This also provides a savings in kernel memory. When updating the
device tree old properties are never free'ed since there is no
usecount on properties. This behavior leads to a new copy of the
property being allocated every time a LMB is added or removed (i.e. a
request to add 100 LMBs creates 100 new copies of the property). With
this update only a single new property is created when a DLPAR request
completes successfully.
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
