Without TSC_KNOWN_FREQ the TSC clocksource is registered so late that the
kernel first switches to the HPET. Using HPET on large CPU count machines is
undesirable.
Therefore register a tsc-early clocksource using the preliminary tsc_khz
from quick calibration. Then when the final TSC calibration is done, it
can switch to the tuned frequency.
The only notably problem is that the real tsc clocksource must be marked
with CLOCK_SOURCE_VALID_FOR_HRES, otherwise it will not be selected when
unregistering tsc-early. tsc-early cannot be left registered, because then
the clocksource code would fall back to it when we tsc clocksource is
marked unstable later.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: len.brown@intel.com
Cc: rui.zhang@intel.com
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20171222092243.431585460@infradead.org
Zhang Rui reported that a Surface Pro 4 will fail to boot with
lapic=notscdeadline. Part of the problem is that that machine doesn't have
a PIT.
If, for some reason, the TSC init has to fall back to TSC calibration, it
relies on the PIT to be present.
Allow TSC calibration to reliably fall back to HPET.
The below results in an accurate TSC measurement when forced on a IVB:
tsc: Unable to calibrate against PIT
tsc: No reference (HPET/PMTIMER) available
tsc: Unable to calibrate against PIT
tsc: using HPET reference calibration
tsc: Detected 2792.451 MHz processor
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: len.brown@intel.com
Cc: rui.zhang@intel.com
Link: https://lkml.kernel.org/r/20171222092243.333145937@infradead.org
Pull x86 pti updates from Thomas Gleixner:
"This contains:
- a PTI bugfix to avoid setting reserved CR3 bits when PCID is
disabled. This seems to cause issues on a virtual machine at least
and is incorrect according to the AMD manual.
- a PTI bugfix which disables the perf BTS facility if PTI is
enabled. The BTS AUX buffer is not globally visible and causes the
CPU to fault when the mapping disappears on switching CR3 to user
space. A full fix which restores BTS on PTI is non trivial and will
be worked on.
- PTI bugfixes for EFI and trusted boot which make sure that the user
space visible page table entries have the NX bit cleared
- removal of dead code in the PTI pagetable setup functions
- add PTI documentation
- add a selftest for vsyscall to verify that the kernel actually
implements what it advertises.
- a sysfs interface to expose vulnerability and mitigation
information so there is a coherent way for users to retrieve the
status.
- the initial spectre_v2 mitigations, aka retpoline:
+ The necessary ASM thunk and compiler support
+ The ASM variants of retpoline and the conversion of affected ASM
code
+ Make LFENCE serializing on AMD so it can be used as speculation
trap
+ The RSB fill after vmexit
- initial objtool support for retpoline
As I said in the status mail this is the most of the set of patches
which should go into 4.15 except two straight forward patches still on
hold:
- the retpoline add on of LFENCE which waits for ACKs
- the RSB fill after context switch
Both should be ready to go early next week and with that we'll have
covered the major holes of spectre_v2 and go back to normality"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (28 commits)
x86,perf: Disable intel_bts when PTI
security/Kconfig: Correct the Documentation reference for PTI
x86/pti: Fix !PCID and sanitize defines
selftests/x86: Add test_vsyscall
x86/retpoline: Fill return stack buffer on vmexit
x86/retpoline/irq32: Convert assembler indirect jumps
x86/retpoline/checksum32: Convert assembler indirect jumps
x86/retpoline/xen: Convert Xen hypercall indirect jumps
x86/retpoline/hyperv: Convert assembler indirect jumps
x86/retpoline/ftrace: Convert ftrace assembler indirect jumps
x86/retpoline/entry: Convert entry assembler indirect jumps
x86/retpoline/crypto: Convert crypto assembler indirect jumps
x86/spectre: Add boot time option to select Spectre v2 mitigation
x86/retpoline: Add initial retpoline support
objtool: Allow alternatives to be ignored
objtool: Detect jumps to retpoline thunks
x86/pti: Make unpoison of pgd for trusted boot work for real
x86/alternatives: Fix optimize_nops() checking
sysfs/cpu: Fix typos in vulnerability documentation
x86/cpu/AMD: Use LFENCE_RDTSC in preference to MFENCE_RDTSC
...
The INTEL_FAM6_SKYLAKE_X hardcoded crystal_khz value of 25MHZ is
problematic:
- SKX workstations (with same model # as server variants) use a 24 MHz
crystal. This results in a -4.0% time drift rate on SKX workstations.
- SKX servers subject the crystal to an EMI reduction circuit that reduces its
actual frequency by (approximately) -0.25%. This results in -1 second per
10 minute time drift as compared to network time.
This issue can also trigger a timer and power problem, on configurations
that use the LAPIC timer (versus the TSC deadline timer). Clock ticks
scheduled with the LAPIC timer arrive a few usec before the time they are
expected (according to the slow TSC). This causes Linux to poll-idle, when
it should be in an idle power saving state. The idle and clock code do not
graciously recover from this error, sometimes resulting in significant
polling and measurable power impact.
Stop using native_calibrate_tsc() for INTEL_FAM6_SKYLAKE_X.
native_calibrate_tsc() will return 0, boot will run with tsc_khz = cpu_khz,
and the TSC refined calibration will update tsc_khz to correct for the
difference.
[ tglx: Sanitized change log ]
Fixes: 6baf3d6182 ("x86/tsc: Add additional Intel CPU models to the crystal quirk list")
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/ff6dcea166e8ff8f2f6a03c17beab2cb436aa779.1513920414.git.len.brown@intel.com
If the crystal frequency cannot be determined via CPUID(15).crystal_khz or
the built-in table then native_calibrate_tsc() will still set the
X86_FEATURE_TSC_KNOWN_FREQ flag which prevents the refined TSC calibration.
As a consequence such systems use cpu_khz for the TSC frequency which is
incorrect when cpu_khz != tsc_khz resulting in time drift.
Return early when the crystal frequency cannot be retrieved without setting
the X86_FEATURE_TSC_KNOWN_FREQ flag. This ensures that the refined TSC
calibration is invoked.
[ tglx: Steam-blastered changelog. Sigh ]
Fixes: 4ca4df0b7e ("x86/tsc: Mark TSC frequency determined by CPUID as known")
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Cc: Bin Gao <bin.gao@intel.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/0fe2503aa7d7fc69137141fc705541a78101d2b9.1513920414.git.len.brown@intel.com
Enable the use of -mindirect-branch=thunk-extern in newer GCC, and provide
the corresponding thunks. Provide assembler macros for invoking the thunks
in the same way that GCC does, from native and inline assembler.
This adds X86_FEATURE_RETPOLINE and sets it by default on all CPUs. In
some circumstances, IBRS microcode features may be used instead, and the
retpoline can be disabled.
On AMD CPUs if lfence is serialising, the retpoline can be dramatically
simplified to a simple "lfence; jmp *\reg". A future patch, after it has
been verified that lfence really is serialising in all circumstances, can
enable this by setting the X86_FEATURE_RETPOLINE_AMD feature bit in addition
to X86_FEATURE_RETPOLINE.
Do not align the retpoline in the altinstr section, because there is no
guarantee that it stays aligned when it's copied over the oldinstr during
alternative patching.
[ Andi Kleen: Rename the macros, add CONFIG_RETPOLINE option, export thunks]
[ tglx: Put actual function CALL/JMP in front of the macros, convert to
symbolic labels ]
[ dwmw2: Convert back to numeric labels, merge objtool fixes ]
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: gnomes@lxorguk.ukuu.org.uk
Cc: Rik van Riel <riel@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: thomas.lendacky@amd.com
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Jiri Kosina <jikos@kernel.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Kees Cook <keescook@google.com>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: https://lkml.kernel.org/r/1515707194-20531-4-git-send-email-dwmw@amazon.co.uk
On machines where the GART aperture is mapped over physical RAM
/proc/vmcore contains the remapped range and reading it may cause hangs or
reboots.
In the past, the GART region was added into the resource map, implemented
by commit 56dd669a13 ("[PATCH] Insert GART region into resource map")
However, inserting the iomem_resource from the early GART code caused
resource conflicts with some AGP drivers (bko#72201), which got avoided by
reverting the patch in commit 707d4eefbd ("Revert [PATCH] Insert GART
region into resource map"). This revert introduced the /proc/vmcore bug.
The vmcore ELF header is either prepared by the kernel (when using the
kexec_file_load syscall) or by the kexec userspace (when using the kexec_load
syscall). Since we no longer have the GART iomem resource, the userspace
kexec has no way of knowing which region to exclude from the ELF header.
Changes from v1 of this patch:
Instead of excluding the aperture from the ELF header, this patch
makes /proc/vmcore return zeroes in the second kernel when attempting to
read the aperture region. This is done by reusing the
gart_oldmem_pfn_is_ram infrastructure originally intended to exclude XEN
balooned memory. This works for both, the kexec_file_load and kexec_load
syscalls.
[Note that the GART region is the same in the first and second kernels:
regardless whether the first kernel fixed up the northbridge/bios setting
and mapped the aperture over physical memory, the second kernel finds the
northbridge properly configured by the first kernel and the aperture
never overlaps with e820 memory because the second kernel has a fake e820
map created from the crashkernel memory regions. Thus, the second kernel
keeps the aperture address/size as configured by the first kernel.]
register_oldmem_pfn_is_ram can only register one callback and returns an error
if the callback has been registered already. Since XEN used to be the only user
of this function, it never checks the return value. Now that we have more than
one user, I added a WARN_ON just in case agp, XEN, or any other future user of
register_oldmem_pfn_is_ram were to step on each other's toes.
Fixes: 707d4eefbd ("Revert [PATCH] Insert GART region into resource map")
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Baoquan He <bhe@redhat.com>
Cc: Toshi Kani <toshi.kani@hpe.com>
Cc: David Airlie <airlied@linux.ie>
Cc: yinghai@kernel.org
Cc: joro@8bytes.org
Cc: kexec@lists.infradead.org
Cc: Borislav Petkov <bp@alien8.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Link: https://lkml.kernel.org/r/20180106010013.73suskgxm7lox7g6@dwarf.suse.cz
phys_to_dma, dma_to_phys and dma_capable are helpers published by
architecture code for use of swiotlb and xen-swiotlb only. Drivers are
not supposed to use these directly, but use the DMA API instead.
Move these to a new asm/dma-direct.h helper, included by a
linux/dma-direct.h wrapper that provides the default linear mapping
unless the architecture wants to override it.
In the MIPS case the existing dma-coherent.h is reused for now as
untangling it will take a bit of work.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Instead of blacklisting all model 79 CPUs when attempting a late
microcode loading, limit that only to CPUs with microcode revisions <
0x0b000021 because only on those late loading may cause a system hang.
For such processors either:
a) a BIOS update which might contain a newer microcode revision
or
b) the early microcode loading method
should be considered.
Processors with revisions 0x0b000021 or higher will not experience such
hangs.
For more details, see erratum BDF90 in document #334165 (Intel Xeon
Processor E7-8800/4800 v4 Product Family Specification Update) from
September 2017.
[ bp: Heavily massage commit message and pr_* statements. ]
Fixes: 723f2828a9 ("x86/microcode/intel: Disable late loading on model 79")
Signed-off-by: Jia Zhang <qianyue.zj@alibaba-inc.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Cc: <stable@vger.kernel.org> # v4.14
Link: http://lkml.kernel.org/r/1514772287-92959-1-git-send-email-qianyue.zj@alibaba-inc.com
Pull more x86 pti fixes from Thomas Gleixner:
"Another small stash of fixes for fallout from the PTI work:
- Fix the modules vs. KASAN breakage which was caused by making
MODULES_END depend of the fixmap size. That was done when the cpu
entry area moved into the fixmap, but now that we have a separate
map space for that this is causing more issues than it solves.
- Use the proper cache flush methods for the debugstore buffers as
they are mapped/unmapped during runtime and not statically mapped
at boot time like the rest of the cpu entry area.
- Make the map layout of the cpu_entry_area consistent for 4 and 5
level paging and fix the KASLR vaddr_end wreckage.
- Use PER_CPU_EXPORT for per cpu variable and while at it unbreak
nvidia gfx drivers by dropping the GPL export. The subject line of
the commit tells it the other way around, but I noticed that too
late.
- Fix the ASM alternative macros so they can be used in the middle of
an inline asm block.
- Rename the BUG_CPU_INSECURE flag to BUG_CPU_MELTDOWN so the attack
vector is properly identified. The Spectre mitigations will come
with their own bug bits later"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/pti: Rename BUG_CPU_INSECURE to BUG_CPU_MELTDOWN
x86/alternatives: Add missing '\n' at end of ALTERNATIVE inline asm
x86/tlb: Drop the _GPL from the cpu_tlbstate export
x86/events/intel/ds: Use the proper cache flush method for mapping ds buffers
x86/kaslr: Fix the vaddr_end mess
x86/mm: Map cpu_entry_area at the same place on 4/5 level
x86/mm: Set MODULES_END to 0xffffffffff000000
Pull EFI updates from Thomas Gleixner:
- A fix for a add_efi_memmap parameter regression which ensures that
the parameter is parsed before it is used.
- Reinstate the virtual capsule mapping as the cached copy turned out
to break Quark and other things
- Remove Matt Fleming as EFI co-maintainer. He stepped back a few days
ago. Thanks Matt for all your great work!
* 'efi-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Remove Matt Fleming as EFI co-maintainer
efi/capsule-loader: Reinstate virtual capsule mapping
x86/efi: Fix kernel param add_efi_memmap regression
acpi_get_override_irq() followed by acpi_register_gsi() returns negative
error code on failure.
Propagate it from acpi_gsi_to_irq() to callers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[ rjw : Subject/changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull x86 page table isolation fixes from Thomas Gleixner:
"A couple of urgent fixes for PTI:
- Fix a PTE mismatch between user and kernel visible mapping of the
cpu entry area (differs vs. the GLB bit) and causes a TLB mismatch
MCE on older AMD K8 machines
- Fix the misplaced CR3 switch in the SYSCALL compat entry code which
causes access to unmapped kernel memory resulting in double faults.
- Fix the section mismatch of the cpu_tss_rw percpu storage caused by
using a different mechanism for declaration and definition.
- Two fixes for dumpstack which help to decode entry stack issues
better
- Enable PTI by default in Kconfig. We should have done that earlier,
but it slipped through the cracks.
- Exclude AMD from the PTI enforcement. Not necessarily a fix, but if
AMD is so confident that they are not affected, then we should not
burden users with the overhead"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/process: Define cpu_tss_rw in same section as declaration
x86/pti: Switch to kernel CR3 at early in entry_SYSCALL_compat()
x86/dumpstack: Print registers for first stack frame
x86/dumpstack: Fix partial register dumps
x86/pti: Make sure the user/kernel PTEs match
x86/cpu, x86/pti: Do not enable PTI on AMD processors
x86/pti: Enable PTI by default
The show_regs_safe() logic is wrong. When there's an iret stack frame,
it prints the entire pt_regs -- most of which is random stack data --
instead of just the five registers at the end.
show_regs_safe() is also poorly named: the on_stack() checks aren't for
safety. Rename the function to show_regs_if_on_stack() and add a
comment to explain why the checks are needed.
These issues were introduced with the "partial register dump" feature of
the following commit:
b02fcf9ba1 ("x86/unwinder: Handle stack overflows more gracefully")
That patch had gone through a few iterations of development, and the
above issues were artifacts from a previous iteration of the patch where
'regs' pointed directly to the iret frame rather than to the (partially
empty) pt_regs.
Tested-by: Alexander Tsoy <alexander@tsoy.me>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toralf Förster <toralf.foerster@gmx.de>
Cc: stable@vger.kernel.org
Fixes: b02fcf9ba1 ("x86/unwinder: Handle stack overflows more gracefully")
Link: http://lkml.kernel.org/r/5b05b8b344f59db2d3d50dbdeba92d60f2304c54.1514736742.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
AMD processors are not subject to the types of attacks that the kernel
page table isolation feature protects against. The AMD microarchitecture
does not allow memory references, including speculative references, that
access higher privileged data when running in a lesser privileged mode
when that access would result in a page fault.
Disable page table isolation by default on AMD processors by not setting
the X86_BUG_CPU_INSECURE feature, which controls whether X86_FEATURE_PTI
is set.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20171227054354.20369.94587.stgit@tlendack-t1.amdoffice.net
Pull x86 fixes from Thomas Gleixner:
"A couple of fixlets for x86:
- Fix the ESPFIX double fault handling for 5-level pagetables
- Fix the commandline parsing for 'apic=' on 32bit systems and update
documentation
- Make zombie stack traces reliable
- Fix kexec with stack canary
- Fix the delivery mode for APICs which was missed when the x86
vector management was converted to single target delivery. Caused a
regression due to the broken hardware which ignores affinity
settings in lowest prio delivery mode.
- Unbreak modules when AMD memory encryption is enabled
- Remove an unused parameter of prepare_switch_to"
* 'x86/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic: Switch all APICs to Fixed delivery mode
x86/apic: Update the 'apic=' description of setting APIC driver
x86/apic: Avoid wrong warning when parsing 'apic=' in X86-32 case
x86-32: Fix kexec with stack canary (CONFIG_CC_STACKPROTECTOR)
x86: Remove unused parameter of prepare_switch_to
x86/stacktrace: Make zombie stack traces reliable
x86/mm: Unbreak modules that use the DMA API
x86/build: Make isoimage work on Debian
x86/espfix/64: Fix espfix double-fault handling on 5-level systems
Pull x86 page table isolation fixes from Thomas Gleixner:
"Four patches addressing the PTI fallout as discussed and debugged
yesterday:
- Remove stale and pointless TLB flush invocations from the hotplug
code
- Remove stale preempt_disable/enable from __native_flush_tlb()
- Plug the memory leak in the write_ldt() error path"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ldt: Make LDT pgtable free conditional
x86/ldt: Plug memory leak in error path
x86/mm: Remove preempt_disable/enable() from __native_flush_tlb()
x86/smpboot: Remove stale TLB flush invocations
Pull irq fixes from Thomas Gleixner:
"A rather large update after the kaisered maintainer finally found time
to handle regression reports.
- The larger part addresses a regression caused by the x86 vector
management rework.
The reservation based model does not work reliably for MSI
interrupts, if they cannot be masked (yes, yet another hw
engineering trainwreck). The reason is that the reservation mode
assigns a dummy vector when the interrupt is allocated and switches
to a real vector when the interrupt is requested.
If the MSI entry cannot be masked then the initialization might
raise an interrupt before the interrupt is requested, which ends up
as spurious interrupt and causes device malfunction and worse. The
fix is to exclude MSI interrupts which do not support masking from
reservation mode and assign a real vector right away.
- Extend the extra lockdep class setup for nested interrupts with a
class for the recently added irq_desc::request_mutex so lockdep can
differeniate and does not emit false positive warnings.
- A ratelimit guard for the bad irq printout so in case a bad irq
comes back immediately the system does not drown in dmesg spam"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/msi, x86/vector: Prevent reservation mode for non maskable MSI
genirq/irqdomain: Rename early argument of irq_domain_activate_irq()
x86/vector: Use IRQD_CAN_RESERVE flag
genirq: Introduce IRQD_CAN_RESERVE flag
genirq/msi: Handle reactivation only on success
gpio: brcmstb: Make really use of the new lockdep class
genirq: Guard handle_bad_irq log messages
kernel/irq: Extend lockdep class for request mutex
Andy prefers to be paranoid about the pagetable free in the error path of
write_ldt(). Make it conditional and warn whenever the installment of a
secondary LDT fails.
Requested-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pull x86 page table isolation updates from Thomas Gleixner:
"This is the final set of enabling page table isolation on x86:
- Infrastructure patches for handling the extra page tables.
- Patches which map the various bits and pieces which are required to
get in and out of user space into the user space visible page
tables.
- The required changes to have CR3 switching in the entry/exit code.
- Optimizations for the CR3 switching along with documentation how
the ASID/PCID mechanism works.
- Updates to dump pagetables to cover the user space page tables for
W+X scans and extra debugfs files to analyze both the kernel and
the user space visible page tables
The whole functionality is compile time controlled via a config switch
and can be turned on/off on the command line as well"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (32 commits)
x86/ldt: Make the LDT mapping RO
x86/mm/dump_pagetables: Allow dumping current pagetables
x86/mm/dump_pagetables: Check user space page table for WX pages
x86/mm/dump_pagetables: Add page table directory to the debugfs VFS hierarchy
x86/mm/pti: Add Kconfig
x86/dumpstack: Indicate in Oops whether PTI is configured and enabled
x86/mm: Clarify the whole ASID/kernel PCID/user PCID naming
x86/mm: Use INVPCID for __native_flush_tlb_single()
x86/mm: Optimize RESTORE_CR3
x86/mm: Use/Fix PCID to optimize user/kernel switches
x86/mm: Abstract switching CR3
x86/mm: Allow flushing for future ASID switches
x86/pti: Map the vsyscall page if needed
x86/pti: Put the LDT in its own PGD if PTI is on
x86/mm/64: Make a full PGD-entry size hole in the memory map
x86/events/intel/ds: Map debug buffers in cpu_entry_area
x86/cpu_entry_area: Add debugstore entries to cpu_entry_area
x86/mm/pti: Map ESPFIX into user space
x86/mm/pti: Share entry text PMD
x86/entry: Align entry text section to PMD boundary
...
Some of the APIC incarnations are operating in lowest priority delivery
mode. This worked as long as the vector management code allocated the same
vector on all possible CPUs for each interrupt.
Lowest priority delivery mode does not necessarily respect the affinity
setting and may redirect to some other online CPU. This was documented
somewhere in the old code and the conversion to single target delivery
missed to update the delivery mode of the affected APIC drivers which
results in spurious interrupts on some of the affected CPU/Chipset
combinations.
Switch the APIC drivers over to Fixed delivery mode and remove all
leftovers of lowest priority delivery mode.
Switching to Fixed delivery mode is not a problem on these CPUs because the
kernel already uses Fixed delivery mode for IPIs. The reason for this is
that th SDM explicitely forbids lowest prio mode for IPIs. The reason is
obvious: If the irq routing does not honor destination targets in lowest
prio mode then an IPI targeted at CPU1 might end up on CPU0, which would be
a fatal problem in many cases.
As a consequence of this change, the apic::irq_delivery_mode field is now
pointless, but this needs to be cleaned up in a separate patch.
Fixes: fdba46ffb4 ("x86/apic: Get rid of multi CPU affinity")
Reported-by: vcaputo@pengaru.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: vcaputo@pengaru.com
Cc: Pavel Machek <pavel@ucw.cz>
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1712281140440.1688@nanos
As per note in 5.2.9 Fixed ACPI Description Table (FADT) chapter of ACPI
specification, on HW-reduced platforma OSPM should ignore fields related
to the ACPI HW register interface, one of which is SCI_INT.
Follow the spec and ignore any configuration done for interrupt line
defined by SCI_INT if FADT specifies a HW-reduced platform.
HW-reduced platforms will still be able to use SCI in case it provides
an override record in MADT table.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
0 is valid hardware interrupt which might be in some cases overridden.
Due to this, switch to INVALID_ACPI_IRQ to mark SCI override not set.
While here, change the type of the variable from int to u32 to match
the GSI type used in the rest of the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
