The order between "syscon" and "simple-mfd" is important because in these
particular cases, the node needs to be first a "simple-mfd" to expose
it's sub-nodes, and later on a "syscon" to permit other nodes to access
this register space through the "syscon" mechanism.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
DMC is a small memory region with various registers,
including the ones needed for the canvas module.
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Devices using the new V4L2 mem2mem vdec require a larger CMA pool. As
nearly all GX* devices are video/media focused and will use it, set a
larger (256MB) default value.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Vendor firmware/uboot has different reserved regions depending on
firmware version, but current codebase reserves the same regions on
GXL and GXBB, so move the additional reserved memory region to common
.dtsi.
Found when putting a recent vendor u-boot on meson-gxbb-p200.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Based on updated information from Amlogic, correct the register range
for the SD/eMMC blocks to the right size.
Reported-by: Yixun Lan <yixun.lan@amlogic.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
efuse is one time programmable, so it is safer to deny write request
to this memory, unless the user is savvy enough to remove the read-only
flag from DTB
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move the SPDX-License-Identifier lines to the top and drop the
license splat.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The DT spec recommends that node-names have generic names like "bus".
Fix that in the Amlogic DTs, while leaving the label names to have more
SoC-specific names that match with the HW documentation.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now the Amlogic Meson GX SoCs datasheet documents all the Reset registers,
grow the memory in the node to allow usage of the level registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds support for the VPU Power Domain nodes, and attaches the
VPU power domain to the VPU node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Since the switch to documented uart bindings, the old undocumented
compatible binding was left for simplicity.
This patch removes these unneeded compatible strings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Since the switch to documented uart bindings, the clocks are
redefined in the SoC family dtsi file.
This patch removes these unneeded properties.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds the AO CEC node in all the HDMI enabled boards DTS.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The AO clkc needs to be updated to new bindings with an system control parent
node and moving the clkc node as subnode.
Also adds the SoC specific compatible following the bindings requirements.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch switches to the stable UART bindings but also add the correct
gate clock to the non-AO UART nodes for GXBB and GXL SoCs.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
the mailbox and ethmac nodes used the magic number "0" instead of the
GIC_SPI preprocessor macro. Additionally the ethmac used the magic
number "1" instead of IRQ_TYPE_EDGE_RISING.
Fix this to make the .dtsi easier to read.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Use the specific compatible for AO pwms so the pwms input can
be correctly set
FDIV4 is not present on the pwm A0, so change kadhas vim input
clocks to xtal.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add nodes for the SPICC controller on GX common dtsi, GXBB and
GXL dtsi files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Switch to use the new compatible for the SCPI sensors so that the
sensor readings are reported using the correct scale.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
The HDMI modes needs more CMA memory to be reserved at boot-time.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Prepend the compatible strings with a GX generic name in nodes compatible with
the GXBB HW and keep the same scheme as other nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Since we know the GXBB and GXL/GXM share more hardware, we can safely move
the remaining peripheral nodes present in the GXBB dtsi to the common GX dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The ethmac node has to be configured for each board due to different
pinctrl nodes for RGMII/RMII. Thus the phy-mode should be specified at
the same place (= in the board .dts), making it easier to read the board
.dts file (because the phy-mode is stated explicitly, without requiring
developers to read all "parent" .dtsi as well).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add the SAR ADC to meson-gxbb.dtsi and meson-gxl.dtsi. GXBB provides a
10-bit ADC while GXL and GXM provide a 12-bit ADC.
Some boards use resistor ladder buttons connected through one of the ADC
channels. On newer devices (GXL and GXM) some boards use pull-ups/downs
to change the resistance (and thus the ADC value) on one of the ADC
channels to indicate the board revision.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
All Meson GX SoCs (GXBB, GXL and GXM) have a PWM controller within the
AO domain. When one of the board's LEDs is connected to one of the AO
PWM pins then this can be used to dim that LED (when the leds-pwm driver
is used).
Add the pwm_AO_ab to allow such devices to use the leds-pwm driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Amlogic Meson GXBB/GXL/GXM secure monitor uses part of the memory space,
this patch adds these reserved zones.
Without such reserved memory zones, running the following stress command :
$ stress-ng --vm 16 --vm-bytes 128M --timeout 10s
multiple times:
Could lead to the following kernel crashes :
[ 46.937975] Bad mode in Error handler detected on CPU1, code 0xbf000000 -- SError
...
[ 47.058536] Internal error: Attempting to execute userspace memory: 8600000f [#3] PREEMPT SMP
...
Instead of the OOM killer.
Fixes: 4f24eda840 ("ARM64: dts: Prepare configs for Amlogic Meson GXBaby")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
[khilman: added Fixes tag, added _reserved and unit addresses]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds the missing node for the uart_AO_B port to the meson-gx.dtsi
(as this is supported by GXBB, GXL and GXM) along with the required
pinctrl pins. This is required as some boards are using it (the boards
from the Khadas VIM series for example have it exposed on the pin
headers).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
SCPI and SRAM are identical on GXBB and GXL. Moving the corresponding
nodes to meson-gx adds support for the thermal sensor on GXL based
devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: add scpi_clocks label]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
meson-gx.dtsi was directly derived from meson-gxbb.dtsi, so keep the
copyrights in chronological order to not give a wrong impression.
Fixes: c328666d58 ("ARM64: dts: amlogic: Add Meson GX dtsi from GXBB")
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Move common nodes between GXBB and GXL in to the common GX dtsi.
Leave the clock attributes in the GXBB dtsi for now.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add binding and basic support for the SD/eMMC controller on Amlogic
S905/GXBB devices.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: added nodes for GX, enabled SDIO on P20x]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
In order to remove the boot warning :
[ 2.290933] Unable to detect cache hierarchy from DT for CPU 0
And add missing L2 cache hierarchy information, add a simple l2 cache node
and reference it from the A53 cpu nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
