This adds labels to commonly used device-tree nodes so that derivative
boards can avoid ahb/apb hierarchy.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
The Marvell switches report their interrupts in a level sensitive way.
When using edge sensitive detection a race condition in the interrupt
handler of the swich might result in the OS to miss all future events
which might make the switch non-functional.
The problem is that both mv88e6xxx_g2_irq_thread_fn() and
mv88e6xxx_g1_irq_thread_work() sample the irq cause register
(MV88E6XXX_G2_INT_SRC and MV88E6XXX_G1_STS respectively) once and then
handle the observed sources. If after sampling but before all observed
irq sources are handled a new irq source gets active this is not noticed
by the handler which returns unsuspecting, but the interrupt line stays
active which prevents the edge detector to kick in.
All device trees but imx6qdl-zii-rdu2 get this right (most of them by
not specifying an interrupt parent). So fix imx6qdl-zii-rdu2
accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: f64992d1a9 ("ARM: dts: imx6: RDU2: Add Switch interrupts")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
One omap dts mismerge fix
The dts patch for droid4 PWM vibrator has added gpio6 entries to the wrong
node. Let's fix it with a note that there seems to be also other GPIO PWM
issues to fix still to get the PWM vibrator working. So this can wait for
v4.19 merge cycle if necessary.
* tag 'omap-for-v4.18/fixes-rc5-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: fix dts w.r.t. pwm
Signed-off-by: Olof Johansson <olof@lixom.net>
According to the system control bindings, the A3-A4 SRAM node should be
a child node of the SRAM it belongs to. However, it was introduced at the
same level, therefore breaking the binding. Fix this.
Fixes: 8587019625 ("ARM: sun5i: a13: Merge common controllers into the common DTSI")
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
address-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
address-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
ddress-cells/size-cells is unnecessary for dwmac-sun8i node.
It was in early days, but since a mdio node is used, it could be
removed.
This patch fix the following DT warning:
Warning (avoid_unnecessary_addr_size): /soc/ethernet@1c50000: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
dts reports incorrect usage of these properties in gpio-keys node.
Warning (avoid_unnecessary_addr_size): /gpio-keys: unnecessary
The patch is removing these useless properties.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Include GPIO dt-bindings and use GPIO_ACTIVE_* constants
to improve readability
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
According to the reference manual, the board has two Micron
MT41K256M16HA-125 DDR3L memory ICs, which have 512 MiB each
Tested on a ZYBO-Z7-20 board
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Replace the current value of the model property by a more accurate
description of each board (which includes the manufacturer), as some
of the boards had the same value ("Xilinx Zynq")
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Both boards are made by Avnet, Inc. So add an additional
value to the compatible property
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a dts for MYIR Z-turn board and respective target in Makefile.
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The aspeed pwm driver always sets the clock source to 24MHz, specify
the fixed clock in device tree to make sure the driver is using the
correct clock frequency to calculate the fan speed.
Signed-off-by: Lei YU <mine260309@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the Ethernet and Realtek switch device to the
D-Link DIR-685 Gemini-based device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Tested on a revision G board.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are two variants of imx6ul-pico boards: one with 256MB and
another one with 512MB of RAM.
Do not hardcode the memory size in the device tree and let the
bootloader fill the correct value instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SL EVK board, pfuze100 sw4 supplies
LPDDR2 which is critical for system, must be
always on.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, pfuze100 sw4 supplies
LPDDR3 which is critical for system, must be
always on.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SX SDB Rev-A board, pfuze100 sw4 supplies
csi, audio codec and i2c etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6QDL Sabre-SD board, pfuze100 sw4 supplies
GPS, touch and RGMII etc., these modules do NOT
implement power domain control, so pfuze100 sw4
needs to be always on to make sure these modules
work normally.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SL EVK board, the MX6SL_PAD_KEY_ROW5 pin is
used as lcd 3v3 regulator control pin, need to make
sure MX6SL_PAD_KEY_ROW5 is muxed as GPIO function
for controlling lcd 3v3 regulator.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by; Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
pwm node should not be under gpio6 node in the device tree.
This fixes detection of the pwm on Droid 4.
Fixes: 6d7bdd328d ("ARM: dts: omap4-droid4: update touchscreen")
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[tony@atomide.com: added fixes tag]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This display configuration isn't working as-is as it depends on the
tfp410 LCD to HDMI bridge. This will need to be updated later once
the DRM MXSFB driver will be the default.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6sl soc has gpu_2d and gpu_vg, no 3d support:
etnaviv-gpu 2200000.gpu: model: GC320, revision: 5007
etnaviv-gpu 2204000.gpu: model: GC355, revision: 1215
The IP blocks seem to be already supported.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6SLL EVK board, lcd regulator is controlled
by GPIO4 IO03 using MX6SLL_PAD_KEY_ROW5__GPIO4_IO03 pin,
NOT MX6SLL_PAD_ECSPI1_SCLK__GPIO4_IO08, correct it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add 'secure-reg-access' property to enable PMU and hardware counters
so that they can be properly used with the 'perf' tool.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
[fabio: kept the change only in imx53-ppd context]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ConnectCore 6UL Single Board Computer (SBC) Express contains the
ConnectCore 6UL System-On-Module.
Its hardware specifications are:
* 256MB DDR3 memory
* 256MB NAND flash
* Single Ethernet
* USB Host and USB-OTG
* MicroSD external storage
* Groove connectors and Raspberry Pi Hat compatible expansion header
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ConnectCore 6UL System-On-Module has the following hardware
specification:
* Based on a NXP i.MX6UL SoC
* Industrial temperature ranges (-40ºC to +85ºC)
* Up to 1GB DDR3 memory
* Up to 2GB NAND flash
* Dual Ethernet
* On module 802.11 WiFi and Bluetooth 4.2 (QCA6564)
* On module NXP Kinetis KL03
* On module Microchip ATECC508A crypto element
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx51-zii-rdu1 has an external watchdog in the environment
microcontroller, so disable the internal one.
This aligns with what was done in commit 7055f71403 ("ARM: dts:
imx6: RDU2: disable internal watchdog") for imx6 rdu2 board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Normally, we didn't release this kind of baord to user. This specific
board exists only in the early stage of development inside MediaTek -
and that may confuse peoples.
Hence this patch removes related files accordingly.
Cc: John Crispin <john@phrozen.org>
Cc: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The reserved memory for the VGA frame buffer is at the wrong address
for this system.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
