Turns out the undocumented and reserved bits of port status/control
register of the root port need to be set to use the HCI in HSIC mode.
Typically the firmware does this, but that is not always good enough,
because the bits get lost if the HSIC clock is disabled (e.g. when
ehci-mv is build as a module).
This supplements commit 7b104f890a ("USB: EHCI: ehci-mv: add HSIC
support").
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200309130014.548168-1-lkundrak@v3.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
NVIDIA VirtualLink (svid 0x955) has two altmode, vdo=0x1 for
VirtualLink DP mode and vdo=0x3 for NVIDIA test mode. NVIDIA
test device FTB (Function Test Board) reports altmode list with
vdo=0x3 first and then vdo=0x1. The list is:
SVID VDO
0xff01 0xc05
0x28de 0x8085
0x955 0x3
0x955 0x1
Current logic to assign mode value is based on order
in altmode list. This causes a mismatch of CON and SOP altmodes
since NVIDIA GPU connector has order of vdo=0x1 first and then
vdo=0x3. Fixing this by changing the order of vdo values
reported by NVIDIA test device. the new list will be:
SVID VDO
0xff01 0xc05
0x28de 0x8085
0x955 0x1085
0x955 0x3
Also NVIDIA VirtualLink (svid 0x955) uses pin E for display mode.
NVIDIA test device reports vdo of 0x1 so make sure vdo values
always have pin E assignement.
Signed-off-by: Ajay Gupta <ajayg@nvidia.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200310121912.57879-1-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop the struct tty_port pointer and rename the struct usb_serial_port
pointer "port", which is the named used throughout the subsystem and
incidentally also matches the kernel-doc comment.
Signed-off-by: Johan Hovold <johan@kernel.org>
libtraceevent (used by perf and trace-cmd) failed to parse the
xhci_urb_dequeue trace event. This is because the user space trace
event format parsing is not a full C compiler. It can handle some basic
logic, but is not meant to be able to handle everything C can do.
In cases where a trace event field needs to be converted from a number
to a string, there's the __print_symbolic() macro that should be used:
See samples/trace_events/trace-events-sample.h
Some xhci trace events open coded the __print_symbolic() causing the
user spaces tools to fail to parse it. This has to be replaced with
__print_symbolic() instead.
CC: stable@vger.kernel.org
Reported-by: Tzvetomir Stoyanov <tstoyanov@vmware.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=206531
Fixes: 5abdc2e6e1 ("usb: host: xhci: add urb_enqueue/dequeue/giveback tracers")
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200306150858.21904-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Intel PMC microcontroller on the latest Intel platforms
has a new function that allows configuration of the USB
Multiplexer/DeMultiplexer switches that are under the
control of the PMC.
The Intel PMC mux control (aka. mux-agent) can be used for
swapping the USB data role and for entering alternate modes,
DisplayPort or Thunderbolt3.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200302135353.56659-10-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If scatter-gather operation is allowed, a large USB request is split
into multiple TRBs. For preparing TRBs for sg list, driver iterates
over the list and creates TRB for each sg and mark the chain bit to
false for the last sg. The current IOMMU driver is clubbing the list
of sgs which shares a page boundary into one and giving it to USB driver.
With this the number of sgs mapped it not equal to the the number of sgs
passed. Because of this USB driver is not marking the chain bit to false
since it couldn't iterate to the last sg. This patch addresses this issue
by marking the chain bit to false if it is the last mapped sg.
At a practical level, this patch resolves USB transfer stalls
seen with adb on dwc3 based db845c, pixel3 and other qcom
hardware after functionfs gadget added scatter-gather support
around v4.20.
Credit also to Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
who implemented a very similar fix to this issue.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org> #4.20+
Signed-off-by: Pratham Pratap <prathampratap@codeaurora.org>
[jstultz: Slight tweak to remove sg_is_last() usage, reworked
commit message, minor comment tweak]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200302214443.55783-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Address below Coverity complaint (Feb 25, 2020, 8:06 AM CET):
*** CID 1458999: Error handling issues (CHECKED_RETURN)
/drivers/usb/core/hub.c: 1869 in hub_probe()
1863
1864 if (id->driver_info & HUB_QUIRK_CHECK_PORT_AUTOSUSPEND)
1865 hub->quirk_check_port_auto_suspend = 1;
1866
1867 if (id->driver_info & HUB_QUIRK_DISABLE_AUTOSUSPEND) {
1868 hub->quirk_disable_autosuspend = 1;
>>> CID 1458999: Error handling issues (CHECKED_RETURN)
>>> Calling "usb_autopm_get_interface" without checking return value (as is done elsewhere 97 out of 111 times).
1869 usb_autopm_get_interface(intf);
1870 }
1871
1872 if (hub_configure(hub, &desc->endpoint[0].desc) >= 0)
1873 return 0;
1874
Rather than checking the return value of 'usb_autopm_get_interface()',
switch to the usb_autopm_get_interface_no_resume() API, as per:
On Tue, Feb 25, 2020 at 10:32:32AM -0500, Alan Stern wrote:
------ 8< ------
> This change (i.e. 'ret = usb_autopm_get_interface') is not necessary,
> because the resume operation cannot fail at this point (interfaces
> are always powered-up during probe). A better solution would be to
> call usb_autopm_get_interface_no_resume() instead.
------ 8< ------
Fixes: 1208f9e1d7 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: Hardik Gajjar <hgajjar@de.adit-jv.com>
Cc: stable@vger.kernel.org # v4.14+
Reported-by: scan-admin@coverity.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-1-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 4d7201cda2 ("usb: usb251xb: add vdd supply support") didn't
covered the non-DT use-case and so the regualtor_enable() call during
probe will fail on those platforms. Also the commit didn't handled the
error case correctly.
Move devm_regulator_get() out of usb251xb_get_ofdata() to address the
1st issue. This can be done without worries because devm_regulator_get()
handles the non-DT use-case too. Add devm_add_action_or_reset() to
address the 2nd bug.
Fixes: 4d7201cda2 ("usb: usb251xb: add vdd supply support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20200226072644.18490-1-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If there are TRBs pending during reset endpoint operation, the
DMA will advance after reset operation, but it isn't expected,
since the data is not yet available (For OUT, the data is not
yet available). After the data is ready, there won't be any
interrupt since the EP_TRADDR already points to next TRB entry
and doorbell is not set.
To fix it, it toggles cycle bit before reset operation, and restores
it after reset, it could avoid unexpected DMA advance due to
cycle bit is for software during the endpoint reset operation.
Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver uses only GPIO Descriptor Consumer Interface so include
proper header. This fixes compile test failures (e.g. on i386):
drivers/usb/phy/phy-tegra-usb.c: In function ‘ulpi_phy_power_on’:
drivers/usb/phy/phy-tegra-usb.c:695:2: error:
implicit declaration of function ‘gpiod_set_value_cansleep’ [-Werror=implicit-function-declaration]
drivers/usb/phy/phy-tegra-usb.c: In function ‘tegra_usb_phy_probe’:
drivers/usb/phy/phy-tegra-usb.c:1167:11: error:
implicit declaration of function ‘devm_gpiod_get_from_of_node’ [-Werror=implicit-function-declaration]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/1583234960-24909-1-git-send-email-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variables declared in a switch statement before any case statements
cannot be automatically initialized with compiler instrumentation (as
they are not part of any execution flow). With GCC's proposed automatic
stack variable initialization feature, this triggers a warning (and they
don't get initialized). Clang's automatic stack variable initialization
(via CONFIG_INIT_STACK_ALL=y) doesn't throw a warning, but it also
doesn't initialize such variables[1]. Note that these warnings (or silent
skipping) happen before the dead-store elimination optimization phase,
so even when the automatic initializations are later elided in favor of
direct initializations, the warnings remain.
To avoid these problems, move such variables into the "case" where
they're used or lift them up into the main function body.
drivers/usb/gadget/udc/net2280.c: In function ‘handle_stat0_irqs_superspeed’:
drivers/usb/gadget/udc/net2280.c:2871:22: warning: statement will never be executed [-Wswitch-unreachable]
2871 | struct net2280_ep *e;
| ^
[1] https://bugs.llvm.org/show_bug.cgi?id=44916
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/202002201515.DFC51CF@keescook
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Fintek F81532A/534A/535/536 is USB-to-2/4/8/12 serial ports device
and the serial ports are default disabled. Each port contains max 3 pins
GPIO and the 3 pins are default pull high with input mode.
When the serial port had activated (running probe()), we'll transform the
3 pins from GPIO function publicly to control Tranceiver privately use.
We'll default set to 0/0/1 for control transceiver to RS232 mode.
Otherwise, If the serial port is not active, the 3 pins is in GPIO mode
and controlled by global GPIO device with VID/PID: 2c42/16f8.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The Fintek F81532A/534A/535/536 is USB-to-2/4/8/12 serial ports device
and the serial port is default disabled when plugin computer.
The IC is contains devices as following:
1. HUB (all devices is connected with this hub)
2. GPIO/Control device. (enable serial port and control GPIOs)
3. serial port 1 to x (2/4/8/12)
It's most same with F81232, the UART device is difference as follow:
1. TX/RX bulk size is 128/512bytes
2. RX bulk layout change:
F81232: [LSR(1Byte)+DATA(1Byte)][LSR(1Byte)+DATA(1Byte)]...
F81534A:[LEN][Data.....][LSR]
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
[johan: reword an error message]
Signed-off-by: Johan Hovold <johan@kernel.org>
Add tx_empty() function for F81232. Without this, console redirection will
get garbage data.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Extract LSR handler to function that can be re-used by
F81532A/534A/535/536.
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200220132017.GA29262@embeddedor
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
