After making use of the gro_flush_timeout attribute I once got a
tx timeout due to an interrupt that wasn't handled. Seems using
irq_enabled can be racy, and it's not needed any longer anyway,
so remove it. I've never seen a report about such a race before,
therefore treat the change as an improvement.
There's just one small drawback: If a legacy PCI interrupt is used,
and if this interrupt is shared with a device with high interrupt
rate, then we may handle interrupts even if NAPI disabled them,
and we may see a certain performance decrease under high network load.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the return value of napi_complete_done(), this allows users to
use the gro_flush_timeout sysfs attribute as an alternative to classic
interrupt coalescing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We return the VLAN table size through devlink as a simple parameter, we
do not support altering it at runtime:
devlink resource show mdio_bus/fixed-0:1f
mdio_bus/fixed-0:1f:
name VTU size 4096 occ 0 unit entry dpipe_tables none
and after configure a bridge with VLAN filtering:
devlink resource show mdio_bus/fixed-0:1f
mdio_bus/fixed-0:1f:
name VTU size 4096 occ 1 unit entry dpipe_tables none
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this is a mock-up driver with no real data path for now, but we
will have one at some point, enable VLANs while not filtering.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When firmware crashes it's possible to create a coredump for later analysis,
add support to collect the register and memory info from SDIO devices.
The coredump configuration is different between QCA6174 PCI and QCA6174 SDIO,
so add specific registers and memory regions for the latter.
QCA6174 SDIO has two methods to dump the firmware: fastdump and slowdump.
Fastdump is not supported in olded versions of firmware, and for these ath10k
will automatically select slowdump. If firmware supports fastdump, ath10k will
automatically select it. QCA6174 SDIO firmware version
WLAN.RMH.4.4.1-00017-QCARMSWPZ-2 is the first version supporting fastdump.
For slowdump, ath10k_sdio_hif_diag_read() can not be used as the diag
window has a limit value, it is 4 bytes and the dump's buffer length is larger
than it, it will trigger error. So this patch adds ath10k_sdio_read_mem() to
read 4 bytes for each time.
Example output of a firmware crash:
ath10k_sdio mmc1:0001:1: simulating soft firmware crash
ath10k_sdio mmc1:0001:1: firmware crashed! (guid 413d98b1-84c0-4298-b605-2b10ec0c54a5)
ath10k_sdio mmc1:0001:1: qca6174 hw3.2 sdio target 0x05030000 chip_id 0x00000000 sub 0000:0000
ath10k_sdio mmc1:0001:1: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 1
ath10k_sdio mmc1:0001:1: firmware ver WLAN.RMH4.4.1-00126-QCARMSWP-1 api 6 features wowlan,ignore-otp,raw-mode crc32 b84317cf
ath10k_sdio mmc1:0001:1: board_file api 2 bmi_id 0:4 crc32 6364cfcc
ath10k_sdio mmc1:0001:1: htt-ver 3.69 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
ath10k_sdio mmc1:0001:1: firmware register dump:
ath10k_sdio mmc1:0001:1: [00]: 0x05030000 0x000015B3 0x0099908D 0x00955B31
ath10k_sdio mmc1:0001:1: [04]: 0x0099908D 0x00060730 0x00000018 0x004641A0
ath10k_sdio mmc1:0001:1: [08]: 0x0041FAA4 0x0041FA9C 0x00999070 0x00404490
ath10k_sdio mmc1:0001:1: [12]: 0x00000009 0xFFFFFFFF 0x00952CD0 0x00952CE6
ath10k_sdio mmc1:0001:1: [16]: 0x00952CC4 0x00910712 0x00000000 0x00000000
ath10k_sdio mmc1:0001:1: [20]: 0x4099908D 0x0040E9E8 0x00000001 0x00423AC0
ath10k_sdio mmc1:0001:1: [24]: 0x809F3189 0x0040EA48 0x00426240 0xC099908D
ath10k_sdio mmc1:0001:1: [28]: 0x809143A7 0x0040EA68 0x0041FAA4 0x00423A80
ath10k_sdio mmc1:0001:1: [32]: 0x809F1193 0x0040EA88 0x00411770 0x004117E0
ath10k_sdio mmc1:0001:1: [36]: 0x809F0EEE 0x0040EAA8 0x00000000 0x00000000
ath10k_sdio mmc1:0001:1: [40]: 0x80911210 0x0040EAC8 0x00000008 0x00404130
ath10k_sdio mmc1:0001:1: [44]: 0x80911154 0x0040EB28 0x00400000 0x00000000
ath10k_sdio mmc1:0001:1: [48]: 0x8091122D 0x0040EB48 0x00000000 0x00400600
ath10k_sdio mmc1:0001:1: [52]: 0x40910024 0x0040EB78 0x0040AB98 0x0040AB98
ath10k_sdio mmc1:0001:1: [56]: 0x00000000 0x0040EB98 0x009BB001 0x00040020
Tested-on: QCA6174 SDIO WLAN.RMH.4.4.1-00018-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1569310030-834-3-git-send-email-wgong@codeaurora.org
The Kconfig help text contains the phrase "the the" in the help
text. Fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the ARP monitor is used for link detection, ARP replies are
validated for all slaves (arp_validate=3) and fail_over_mac is set to
active, two slaves of an active-backup bond may get stuck in a state
where both of them are active and pass packets that they receive to
the bond. This state makes IPv6 duplicate address detection fail. The
state is reached thus:
1. The current active slave goes down because the ARP target
is not reachable.
2. The current ARP slave is chosen and made active.
3. A new slave is enslaved. This new slave becomes the current active
slave and can reach the ARP target.
As a result, the current ARP slave stays active after the enslave
action has finished and the log is littered with "PROBE BAD" messages:
> bond0: PROBE: c_arp ens10 && cas ens11 BAD
The workaround is to remove the slave with "going back" status from
the bond and re-enslave it. This issue was encountered when DPDK PMD
interfaces were being enslaved to an active-backup bond.
I would be possible to fix the issue in bond_enslave() or
bond_change_active_slave() but the ARP monitor was fixed instead to
keep most of the actions changing the current ARP slave in the ARP
monitor code. The current ARP slave is set as inactive and backup
during the commit phase. A new state, BOND_LINK_FAIL, has been
introduced for slaves in the context of the ARP monitor. This allows
administrators to see how slaves are rotated for sending ARP requests
and attempts are made to find a new active slave.
Fixes: b2220cad58 ("bonding: refactor ARP active-backup monitor")
Signed-off-by: Jiri Wiesner <jwiesner@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every iteration of for_each_available_child_of_node() decrements
reference count of the previous node, however when control
is transferred from the middle of the loop, as in the case of
a return or break or goto, there is no decrement thus ultimately
resulting in a memory leak.
Fix a potential memory leak in gianfar.c by inserting of_node_put()
before the goto statement.
Issue found with Coccinelle.
Signed-off-by: Sumera Priyadarsini <sylphrenadin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even after Tx queues are marked stopped, there exists a
small window where the current packet in the normal Tx
path is still being sent out and loopback selftest ends
up corrupting the same Tx ring. So, ensure selftest takes
the Tx lock to synchronize access the Tx ring.
Fixes: 7235ffae3d ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Work request used for sending loopback packet needs to add
the firmware work request only once. So, fix by using
correct structure size.
Fixes: 7235ffae3d ("cxgb4: add loopback ethtool self-test")
Signed-off-by: Ganji Aravind <ganji.aravind@chelsio.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If efx_nic_init_interrupt fails, or was never run (e.g. due to an earlier
failure in ef100_net_open), freeing irqs in efx_nic_fini_interrupt is not
needed and will cause error messages and stack traces.
So instead, only do this if efx_nic_init_interrupt successfully completed,
as indicated by the new efx->irqs_hooked flag.
Fixes: 965b549f3c ("sfc_ef100: implement ndo_open/close and EVQ probing")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an ef100_net_open() fails, ef100_net_stop() may be called without
channel->rps_flow_id having been written; thus it may hold the address
freed by a previous ef100_net_stop()'s call to efx_remove_filters().
This then causes a double-free when efx_remove_filters() is called
again, leading to a panic.
To prevent this, after freeing it, overwrite it with NULL.
Fixes: a9dc3d5612 ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When downing and upping the ef100 filter table, we need to take a write
lock on efx->filter_sem, not just a read lock, because we may kfree()
the table pointers.
Without this, resets cause a WARN_ON from efx_rwsem_assert_write_locked().
Fixes: a9dc3d5612 ("sfc_ef100: RX filter table management and related gubbins")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remote source MAC addresses can be set on a 'source mode' macvlan
interface via the IFLA_MACVLAN_MACADDR_DATA attribute. This commit
tightens the validation of these MAC addresses to match the validation
already performed when setting or adding a single MAC address via the
IFLA_MACVLAN_MACADDR attribute.
iproute2 uses IFLA_MACVLAN_MACADDR_DATA for its 'macvlan macaddr set'
command, and IFLA_MACVLAN_MACADDR for its 'macvlan macaddr add' command,
which demonstrates the inconsistent behaviour that this commit
addresses:
# ip link add link eth0 name macvlan0 type macvlan mode source
# ip link set link dev macvlan0 type macvlan macaddr add 01:00:00:00:00:00
RTNETLINK answers: Cannot assign requested address
# ip link set link dev macvlan0 type macvlan macaddr set 01:00:00:00:00:00
# ip -d link show macvlan0
5: macvlan0@eth0: <BROADCAST,MULTICAST,DYNAMIC,UP,LOWER_UP> mtu 1500 ...
link/ether 2e:ac:fd:2d:69:f8 brd ff:ff:ff:ff:ff:ff promiscuity 0
macvlan mode source remotes (1) 01:00:00:00:00:00 numtxqueues 1 ...
With this change, the 'set' command will (rightly) fail in the same way
as the 'add' command.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change places that open-code NLA_POLICY_MIN_LEN() to
use the macro instead, giving us flexibility in how we
handle the details of the macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change places that open-code NLA_POLICY_EXACT_LEN() to
use the macro instead, giving us flexibility in how we
handle the details of the macro.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 4329 throughput drops from 40.2 Mbits/sec to 190 Kbits/sec in 2G
11n mode because the commit b41c232d33 ("brcmfmac: reserve 2 credits
for host tx control path"). To fix the issue, host driver only reserves
tx control credit when there is a txctl frame is pending to send. And
we also check available credit by using "not equal to 0" instead of
"greater than 0" because tx_max and tx_seq are circled positive numbers.
Reported-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: b41c232d33 ("brcmfmac: reserve 2 credits for host tx control path")
Signed-off-by: Wright Feng <wright.feng@cypress.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200813070017.89023-1-wright.feng@cypress.com
ath.git patches for v5.10. Major changes:
ath11k
* add support for QCA6390 PCI devices
wcn36xx
* add support for TX ack
ath9k
* add support for NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 to improve PTK0
rekeying
clang static analysis reports this problem
rndis_wlan.c:3147:25: warning: Assigned value is garbage or undefined
wiphy->max_num_pmkids = le32_to_cpu(caps.num_pmkids);
^ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The setting of caps happens here, with a call to rndis_query_oid()
retval = rndis_query_oid(usbdev,
if (retval >= 0) {
Reviewing rndis_query_oid() shows that on success 0 is returned,
failure is otherwise. So the retval check is not tight enough.
So tighten the retval check. Similar problem in
rndis_wlan_get_caps().
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200811140219.8412-1-trix@redhat.com
A possible call chain is as follow:
mwifiex_sdio_interrupt (sdio.c)
--> mwifiex_main_process (main.c)
--> mwifiex_process_cmdresp (cmdevt.c)
--> mwifiex_process_sta_cmdresp (sta_cmdresp.c)
--> mwifiex_ret_802_11_scan (scan.c)
--> mwifiex_parse_single_response_buf (scan.c)
'mwifiex_sdio_interrupt()' is an interrupt function.
Also note that 'mwifiex_ret_802_11_scan()' already uses GFP_ATOMIC.
So use GFP_ATOMIC instead of GFP_KERNEL when memory is allocated in
'mwifiex_parse_single_response_buf()'.
Fixes: 7c6fa2a843 ("mwifiex: use cfg80211 dynamic scan table and cfg80211_get_bss API")
or
Fixes: 601216e12c ("mwifiex: process RX packets in SDIO IRQ thread directly")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200809092906.744621-1-christophe.jaillet@wanadoo.fr
Clang static analysis reports this error
brcmfmac/core.c:490:4: warning: Dereference of null pointer
(*ifp)->ndev->stats.rx_errors++;
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In this block of code
if (ret || !(*ifp) || !(*ifp)->ndev) {
if (ret != -ENODATA && *ifp)
(*ifp)->ndev->stats.rx_errors++;
brcmu_pkt_buf_free_skb(skb);
return -ENODATA;
}
(*ifp)->ndev being NULL is caught as an error
But then it is used to report the error.
So add a check before using it.
Fixes: 91b632803e ("brcmfmac: Use net_device_stats from struct net_device")
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200802161804.6126-1-trix@redhat.com
As a part of device shutdown the smmu driver will be
stopped and henceforth any IOVA address translation
will not be done. The wlan driver, being one of the
smmu driver consumer, should stop all the dma related
activity as a part of shutdown, and thereby ensuring
that no dma activity is done once the smmu driver
shuts down.
During the device shutdown, the smmu calls shutdown
for all its consumers in order to indicate them to
stop all their dma activities.
Register the shutdown handler to stop the wlan
driver and avoid any dma operations.
Tested-on: WCN3990 hw1.0 SNOC WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1593193981-30161-1-git-send-email-pillair@codeaurora.org
For QCA6390, normal power up and power down can't bring MHI
to a workable state. This happens especially in warm reboot
and rmmod and insmod. Host needs to write a few registers to
bring MHI to normal state.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeauroro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-10-git-send-email-kvalo@codeaurora.org
For QCA6390, wbm2sw1 is used for other purpose rather than
tx completion ring. So use TCL_DATA_RING 0 only for QCA6390.
Add MISC_CAPS_TCL_0_ONLY to control it.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-9-git-send-email-kvalo@codeaurora.org
QCA6390 doesn't enable V2 map and ummap event, so the addr search
flags and type is different from IPQ8074. Assign correct search flags
and type for QCA6390.
Without this change, ping sometimes fails. With this change, now ping
is always successful.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-7-git-send-email-kvalo@codeaurora.org
For QCA6390, it processes the reg chan list event only for phy0,
and it goes to fallback if the phy_id is not valid. For a valid
phy_id but not 0, just discard the event.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-5-git-send-email-kvalo@codeaurora.org
For QCA6390, only one pdev is created and this pdev manages both lmacs, thus
both rxdmas. So host needs to initialize all rxdma related rings for one pdev.
Another difference is for QCA6390, host fills rxbuf to firmware and firmware
further fills the rxbuf to rxbuf ring for each rxdma.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-4-git-send-email-kvalo@codeaurora.org
For QCA6390, it has 2 lmacs and thus 2 rxdmas. However, each rxdma has rxdma0
only, and doesn't have rxdma1. So for QCA6390, don't initialize rxdma1 related
rings such as rx_mon_buf_ring, rx_mon_dst_ring and rx_mon_desc_ring.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-3-git-send-email-kvalo@codeaurora.org
QCA6390 uses MSI interrupt, so need to configure msi_add and
msi_data to dp srngs. As there are so many DP srngs, so need
to group them. Each group shares one MSI interrupt.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-2-git-send-email-kvalo@codeaurora.org
For QCA6390, host puts hardware to Dual Band Simultaneous (DBS) mode by default
so both 2G and 5G bands can be used. Otherwise only the 5G band can be used.
QCA6390 doesn't provide band_to_mac configuration and firmware will do the
band_to_mac map.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-12-git-send-email-kvalo@codeaurora.org
