Add flow control support. The functionality was tested on AR9331 SoC and
confirmed by iperf3 results and HW counters exported over ethtool.
Following test configurations was used:
iMX6S receiver <--- TL-SG1005D switch <---- AR9331 sender
The switch is supporting symmytric flow control:
Settings for eth0:
Supported ports: [ MII ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
Advertised pause frame use: Symmetric
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
--->> Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 100Mb/s
Duplex: Full
Auto-negotiation: on
Port: MII
PHYAD: 4
Transceiver: external
Link detected: yes
The iMX6S system was configured to 10Mbit, to let the switch use flow
control:
- ethtool -s eth0 speed 10
With flow control disabled on AR9331:
- ethtool -A eth0 rx off tx off
- iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-10.00 sec 66.2 MBytes 55.5 Mbits/sec 0.000 ms 0/47155 (0%) sender
[ 5] 0.00-10.04 sec 11.5 MBytes 9.57 Mbits/sec 1.309 ms 38986/47146 (83%) receiver
With flow control enabled on AR9331:
- ethtool -A eth0 rx on tx on
- iperf3 -u -c 172.17.0.1 -b100M -l1472 -t10
[ ID] Interval Transfer Bitrate Jitter Lost/Total Datagrams
[ 5] 0.00-10.00 sec 15.1 MBytes 12.6 Mbits/sec 0.000 ms 0/10727 (0%) sender
[ 5] 0.00-10.05 sec 11.5 MBytes 9.57 Mbits/sec 1.371 ms 2525/10689 (24%) receiver
Similar results are get in opposite direction by introducing extra CPU
load on AR9331:
- chrt 40 dd if=/dev/zero of=/dev/null &
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found the following warning when using W=1 to build kernel:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:3634:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
int ret, coe = priv->hw->rx_csum;
When digging stmmac_get_rx_header_len(), dwmac4_get_rx_header_len() and
dwxgmac2_get_rx_header_len() return 0 only, without any error code to
report. Therefore, it's better to define get_rx_header_len() as void.
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows the driver to report the device link speed
when the ethtool command:
ethtool <nic name>
is run.
Getting the link speed is done via a new admin queue command:
ReportLinkSpeed.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes the driver better aware of the connectivity status of the
device. Based on the device's status register, the driver can call
netif_carrier_{on,off}.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Patricio Noyola <patricion@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds per queue NIC stats to ethtool stats and to report-stats.
These stats are always exposed to guest whether or not the
report-stats flag is turned on.
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds functionality to report driver stats to Hypervisor.
(Users may want to turn this feature off as a matter of privacy
so a "report-stats" flag is added as an ethtool priv option.
It is also disabled by default.)
The hypervisor would trigger a stats report in case "too many"
packets dropped; the stats would be useful in debugging stuck
queues.
A "stats_report_trigger_cnt" stat is added to count the number of times
the hypervisor attempts to trigger stats report.
A timer is also added so that when report-stats is enabled, stat are
updated once every 20 seconds.
Reviewed-by: Yangchun Fu <yangchun@google.com>
Signed-off-by: Kuo Zhao <kuozhao@google.com>
Signed-off-by: David Awogbemila <awogbemila@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following warning when using W=1 to build kernel:
drivers/net/ethernet/smsc/smc91x.c: In function ‘smc_phy_configure’:
drivers/net/ethernet/smsc/smc91x.c:1039:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
int status;
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase Rx ring size to address issue where hardware is reaching
the receive work limit.
Before:
[ 102.223342] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.245695] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.251387] de2104x 0000:17:00.0 eth0: rx work limit reached
[ 102.267444] de2104x 0000:17:00.0 eth0: rx work limit reached
Signed-off-by: Lucy Yan <lucyyan@google.com>
Reviewed-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/huawei/hinic/hinic_hw_eqs.c:115: warning: Excess function parameter 'hw_handler' description in 'hinic_aeq_register_hw_cb'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/huawei/hinic/hinic_hw_api_cmd.c:382: warning: Excess function parameter 'size' description in 'api_cmd'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1841: warning: Excess function parameter 'netdev' description in 'hns_set_multicast_list'
drivers/net/ethernet/hisilicon/hns/hns_enet.c:1841: warning: Excess function parameter 'p' description in 'hns_set_multicast_list'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:137: warning: Excess function parameter 'drv' description in 'hns_xgmac_enable'
drivers/net/ethernet/hisilicon/hns/hns_dsaf_xgmac.c:497: warning: Excess function parameter 'cmd' description in 'hns_xgmac_get_regs'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename cdev to hdev.
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/hisilicon/hns/hnae.c:444: warning: Excess function parameter 'cdev' description in 'hnae_ae_unregister'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/huawei/hinic/hinic_hw_io.c:373: warning: Excess function parameter 'sq_msix_entry' description in 'hinic_io_create_qps'
drivers/net/ethernet/huawei/hinic/hinic_hw_io.c:373: warning: Excess function parameter 'rq_msix_entry' description in 'hinic_io_create_qps'
Rename these wrong names.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the functions mvpp2_isr_handle_xlg() and
mvpp2_isr_handle_gmac_internal(), the bool variable link is assigned a
true value in the case that a given bit of val is set. However, if the
bit is unset, no value is assigned to link and it is then passed to
mvpp2_isr_handle_link() without being initialised. Fix by assigning to
link the value of the bit test.
Build-tested on x86.
Fixes: 36cfd3a6e5 ("net: mvpp2: restructure "link status" interrupt handling")
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/chelsio/cxgb3/t3_hw.c:2209: warning: Excess function parameter 'adapter' description in 'clear_sge_ctxt'
drivers/net/ethernet/chelsio/cxgb3/t3_hw.c:2975: warning: Excess function parameter 'adapter' description in 't3_set_proto_sram'
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using XDP every ingress packet is passed to an eBPF (xdp) program
which returns an action for this packet.
This patch adds counters for the number of times each such action was
received. It also counts all the invalid actions received from the eBPF
program.
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added statistics for TX queues that are used for XDP TX. The statistics
are the same as the ones printed for regular non-XDP TX queues.
The XDP queue statistics can be queried using
`ethtool -S <ifname>`
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new metrics provide granular visibility along multiple network
dimensions and enable troubleshooting and remediation of issues caused
by instances exceeding network performance allowances.
The new statistics can be queried using ethtool command.
Signed-off-by: Guy Tzalik <gtzalik@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type of all stat fields is u64, therefore when iterating over stat
fields in a stats struct, it makes sense to use an offset in 64 bit
resolution. Doing so allows us to drop some of the casting that is
currently used when referencing stats.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Release first buffer as last one since it contains references
to subsequent fragments. This code will be optimized introducing
multi-buffer bit in xdp_buff structure.
Fixes: ca0e014609 ("net: mvneta: move skb build after descriptors processing")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove mvneta_stats from mvneta_swbm_rx_frame signature since now stats
are accounted in mvneta_run_xdp routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We allow drivers to call napi_hash_del() before calling
netif_napi_del() to batch RCU grace periods. This makes
the API asymmetric and leaks internal implementation details.
Soon we will want the grace period to protect more than just
the NAPI hash table.
Restructure the API and have drivers call a new function -
__netif_napi_del() if they want to take care of RCU waits.
Note that only core was checking the return status from
napi_hash_del() so the new helper does not report if the
NAPI was actually deleted.
Some notes on driver oddness:
- veth observed the grace period before calling netif_napi_del()
but that should not matter
- myri10ge observed normal RCU flavor
- bnx2x and enic did not actually observe the grace period
(unless they did so implicitly)
- virtio_net and enic only unhashed Rx NAPIs
The last two points seem to indicate that the calls to
napi_hash_del() were a left over rather than an optimization.
Regardless, it's easy enough to correct them.
This patch may introduce extra synchronize_net() calls for
interfaces which set NAPI_STATE_NO_BUSY_POLL and depend on
free_netdev() to call netif_napi_del(). This seems inevitable
since we want to use RCU for netpoll dev->napi_list traversal,
and almost no drivers set IFF_DISABLE_NETPOLL.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even tho mlx4_core registers the devlink ports, it's mlx4_en
and mlx4_ib which set their type. In situations where one of
the two is not built yet the machine has ports of given type
we see the devlink warning from devlink_port_type_warn() trigger.
Having ports of a type not supported by the kernel may seem
surprising, but it does occur in practice - when the unsupported
port is not plugged in to a switch anyway users are more than happy
not to see it (and potentially allocate any resources to it).
Set the type in mlx4_core if type-specific driver is not built.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to easily change the rx buffer size, rely on
MVNETA_MAX_RX_BUF_SIZE instead of PAGE_SIZE in mvneta_swbm_rx_frame
routine for rx buffer split. Currently this is not an issue since we set
MVNETA_MAX_RX_BUF_SIZE to PAGE_SIZE - MVNETA_SKB_PAD but it is a good to
have to configure a different rx buffer size.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When timestamping a packet there's a delay between the start of the
packet and the point where the hardware actually captures the
timestamp. This difference needs to be considered if we want accurate
timestamps.
This was done on the RX side, but not on the TX side.
Fixes: 2c344ae245 ("igc: Add support for TX timestamping")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The previous timestamping latency numbers were obtained by
interpolating the i210 numbers with the i225 crystal clock value. That
calculation was wrong.
Use the correct values from real measurements.
Fixes: 81b055205e ("igc: Add support for RX timestamping")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The for loop in i40e_set_vsi_promisc() reports errors via dev_err() but
does not propagate the error up the call chain. Instead it continues the
loop and potentially overwrites the reported error value.
This results in the error being recorded in the log buffer, but the
caller might never know anything went the wrong way.
To avoid this situation i40e_set_vsi_promisc() needs to temporarily store
the error after reporting it. This is still not optimal as multiple
different errors may occur, so store the first error and hope that's
the main issue.
Fixes: 37d318d780 (i40e: Remove scheduling while atomic possibility)
Reported-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c: In function ‘i40e_set_vsi_promisc’:
drivers/net/ethernet/intel/i40e/i40e_virtchnl_pf.c:1176:14: error: ‘aq_ret’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
i40e_status aq_ret;
In case the code inside the if statement and the for loop does not get
executed aq_ret will be uninitialized when the variable gets returned at
the end of the function.
Avoid this by changing num_vlans from int to u16, so aq_ret always gets
set. Making this change in additional places as num_vlans should never
be negative.
Fixes: 37d318d780 ("i40e: Remove scheduling while atomic possibility")
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In CMT and NPAR the PF is unknown when the GFS block processes the
packet. Therefore cannot use searcher as it has a per PF database,
and thus ARFS must be disabled.
Fixes: d51e4af5c2 ("qed: aRFS infrastructure support")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for timestamping transmit packets. We allocate SYNC
messages to queue 1, every other message to queue 0.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for receive timestamping. When enabled, the hardware adds
a timestamp into the receive queue descriptor for all received packets
with no filtering. Hence, we can only support NONE or ALL receive
filter modes.
The timestamp in the receive queue contains two bit sof seconds and
the full nanosecond timestamp. This has to be merged with the remainder
of the seconds from the TAI clock to arrive at a full timestamp before
we can convert it to a ktime for the skb hardware timestamp field.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the first level interrupt status registers to determine how to
further process the port interrupt. We will need this to know whether
to invoke the link status processing and/or the PTP processing for
both XLG and GMAC.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link interrupt is used for way more than just the link status; it
comes from a collection of units to do with the port. The Marvell
documentation describes the interrupt as "GOP port X interrupt".
Since we are adding PTP support, and the PTP interrupt uses this,
rename it to be more inline with the documentation.
This interrupt is also mis-named in the DT binding, but we leave that
alone.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "link status" interrupt is used for more than just link status.
Restructure mvpp2_link_status_isr() so we can add additional handling.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
A devlink port may be for a controller consist of PCI device.
A devlink instance holds ports of two types of controllers.
(1) controller discovered on same system where eswitch resides
This is the case where PCI PF/VF of a controller and devlink eswitch
instance both are located on a single system.
(2) controller located on external host system.
This is the case where a controller is located in one system and its
devlink eswitch ports are located in a different system.
When a devlink eswitch instance serves the devlink ports of both
controllers together, PCI PF/VF numbers may overlap.
Due to this a unique phys_port_name cannot be constructed.
For example in below such system controller-0 and controller-1, each has
PCI PF pf0 whose eswitch ports can be present in controller-0.
These results in phys_port_name as "pf0" for both.
Similar problem exists for VFs and upcoming Sub functions.
An example view of two controller systems:
---------------------------------------------------------
| |
| --------- --------- ------- ------- |
----------- | | vf(s) | | sf(s) | |vf(s)| |sf(s)| |
| server | | ------- ----/---- ---/----- ------- ---/--- ---/--- |
| pci rc |=== | pf0 |______/________/ | pf1 |___/_______/ |
| connect | | ------- ------- |
----------- | | controller_num=1 (no eswitch) |
------|--------------------------------------------------
(internal wire)
|
---------------------------------------------------------
| devlink eswitch ports and reps |
| ----------------------------------------------------- |
| |ctrl-0 | ctrl-0 | ctrl-0 | ctrl-0 | ctrl-0 |ctrl-0 | |
| |pf0 | pf0vfN | pf0sfN | pf1 | pf1vfN |pf1sfN | |
| ----------------------------------------------------- |
| |ctrl-1 | ctrl-1 | ctrl-1 | ctrl-1 | ctrl-1 |ctrl-1 | |
| |pf1 | pf1vfN | pf1sfN | pf1 | pf1vfN |pf0sfN | |
| ----------------------------------------------------- |
| |
| |
| --------- --------- ------- ------- |
| | vf(s) | | sf(s) | |vf(s)| |sf(s)| |
| ------- ----/---- ---/----- ------- ---/--- ---/--- |
| | pf0 |______/________/ | pf1 |___/_______/ |
| ------- ------- |
| |
| local controller_num=0 (eswitch) |
---------------------------------------------------------
An example devlink port for external controller with controller
number = 1 for a VF 1 of PF 0:
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev ens2f0pf0vf1 flavour pcivf controller 1 pfnum 0 vfnum 1 external true splittable false
function:
hw_addr 00:00:00:00:00:00
$ devlink port show pci/0000:06:00.0/2 -jp
{
"port": {
"pci/0000:06:00.0/2": {
"type": "eth",
"netdev": "ens2f0pf0vf1",
"flavour": "pcivf",
"controller": 1,
"pfnum": 0,
"vfnum": 1,
"external": true,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:00:00"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A devlink eswitch port may represent PCI PF/VF ports of a controller.
A controller either located on same system or it can be an external
controller located in host where such NIC is plugged in.
Add the ability for driver to specify if a port is for external
controller.
Use such flag in the mlx5_core driver.
An example of an external controller having VF1 of PF0 belong to
controller 1.
$ devlink port show pci/0000:06:00.0/2
pci/0000:06:00.0/2: type eth netdev ens2f0pf0vf1 flavour pcivf pfnum 0 vfnum 1 external true splittable false
function:
hw_addr 00:00:00:00:00:00
$ devlink port show pci/0000:06:00.0/2 -jp
{
"port": {
"pci/0000:06:00.0/2": {
"type": "eth",
"netdev": "ens2f0pf0vf1",
"flavour": "pcivf",
"pfnum": 0,
"vfnum": 1,
"external": true,
"splittable": false,
"function": {
"hw_addr": "00:00:00:00:00:00"
}
}
}
}
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ECPF supports one external host controller. Read controller number
from the device.
Signed-off-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
