GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW = 1 = IRQ_TYPE_EDGE_RISING
Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most of the definitions for peripheral base addresses, interrupt and
DMA information is no longer used, so get rid of them.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that imx35 has been converted to a devicetree-only platform,
retrieve the IIM base address from devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that imx31 and imx35 has been converted to a devicetree-only platform,
retrieve the AVIC base address from devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that imx31 and imx35 has been converted to a devicetree-only platform,
retrieve the CCM base address from devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that imx31 has been converted to a devicetree-only platform,
retrieve the IIM base address from devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that imx27 has been converted to a devicetree-only platform,
retrieve the CCM base address from devicetree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Now that imx27 has been converted to a devicetree-only platform,
retrieve the SYSCTRL base address from devicetree.
To keep devicetree compatibilty the SYSCTRL base address will be
retrieved from the CCM base address plus an 0x800 offset.
This is not a problem as the imx27.dtsi describes the CCM register
range as 0x1000.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable the kernel modules for the board management controller "sl28cpld"
which is used on the SMARC-sAL28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Select the eLCDIF display controller and Raydium RM67191 panel drivers,
so that MIPI DSI can be functional by default on a imx8mq-evk board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Using the native SPI chipselect on i.MX6 is known to be problematic.
Doing it on a imx6q-sabresd causes the SPI NOR probe to fail:
[ 5.388704] spi-nor spi0.0: unrecognized JEDEC id bytes: 00 00 00 00 00 00
Use the GPIO chipselect to avoid such problem.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add an entry for imx6q-logicpd.dtb so that it can be built by default.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is standard practice to have a specific board compatible string, so
pass "logicpd,imx6q-logicpd".
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
dtschema for pca95xx expects GPIO hogs to end with 'hog' prefix. While
touching the hogs, fix indentation (spaces -> tabs).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Build the kernel with `C=2`:
arch/powerpc/kvm/book3s_hv_nested.c:572:25: warning: symbol
'kvmhv_alloc_nested' was not declared. Should it be static?
arch/powerpc/kvm/book3s_64_mmu_radix.c:350:6: warning: symbol
'kvmppc_radix_set_pte_at' was not declared. Should it be static?
arch/powerpc/kvm/book3s_hv.c:3568:5: warning: symbol
'kvmhv_p9_guest_entry' was not declared. Should it be static?
arch/powerpc/kvm/book3s_hv_rm_xics.c:767:15: warning: symbol 'eoi_rc'
was not declared. Should it be static?
arch/powerpc/kvm/book3s_64_vio_hv.c:240:13: warning: symbol
'iommu_tce_kill_rm' was not declared. Should it be static?
arch/powerpc/kvm/book3s_64_vio.c:492:6: warning: symbol
'kvmppc_tce_iommu_do_map' was not declared. Should it be static?
arch/powerpc/kvm/book3s_pr.c:572:6: warning: symbol 'kvmppc_set_pvr_pr'
was not declared. Should it be static?
Those symbols are used only in the files that define them so make them
static to fix the warnings.
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The pin configuration for PMIC interrupt is already set by
imx8mn-evk.dtsi with exactly the same values.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Symphony board uses GPIO from expander as Ethernet PHY reset pin,
not the GPIO1_IO9.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i2c3 clock frequency and pin configuration are already set by
imx8mm-var-som.dtsi.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
FPU initialization handles them currently. However, in the case
of clearcpuid=, some other early initialization code may check for
features before the FPU initialization code is called. Handling the
argument earlier allows the command line to influence those early
initializations.
Signed-off-by: Mike Hommey <mh@glandium.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200921215638.37980-1-mh@glandium.org
The @node passed to cpumask_of_node() can be NUMA_NO_NODE, in that
case it will trigger the following WARN_ON(node >= nr_node_ids) due to
mismatched data types of @node and @nr_node_ids. Actually we should
return cpu_all_mask just like most other architectures do if passed
NUMA_NO_NODE.
Also add a similar check to the inline cpumask_of_node() in numa.h.
Signed-off-by: Zhengyuan Liu <liuzhengyuan@tj.kylinos.cn>
Reviewed-by: Gavin Shan <gshan@redhat.com>
Link: https://lore.kernel.org/r/20200921023936.21846-1-liuzhengyuan@tj.kylinos.cn
Signed-off-by: Will Deacon <will@kernel.org>
When the kernel crashkernel parameter is specified with just a size,
we are supposed to allocate a region from RAM to store the crashkernel.
However, MIPS merely reserves physical address zero with no checking
that there is even RAM there.
Fix this by lifting similar code from x86, importing it to MIPS with the
MIPS specific parameters added. In the absence of any platform specific
information, we allocate the crashkernel region from the first 512MB of
physical memory (limited to CKSEG0 or KSEG0 address range).
When X is not specified, crash_base defaults to 0 (crashkernel=YM@XM).
E.g. without this patch:
The environment as follows:
[ 0.000000] MIPS: machine is loongson,loongson64c-4core-ls7a
...
[ 0.000000] Kernel command line: root=/dev/sda2 crashkernel=96M ...
The warning as follows:
[ 0.000000] Invalid memory region reserved for crash kernel
And the iomem as follows:
00200000-0effffff : System RAM
00200000-00b47f87 : Kernel code
00b47f88-00dfffff : Kernel data
00e60000-01f73c7f : Kernel bss
1a000000-1bffffff : pci@1a000000
...
With this patch:
After increasing crash_base <= 0 handling.
And the iomem as follows:
00200000-0effffff : System RAM
00200000-00b47f87 : Kernel code
00b47f88-00dfffff : Kernel data
00e60000-01f73c7f : Kernel bss
04000000-09ffffff : Crash kernel
1a000000-1bffffff : pci@1a000000
...
Signed-off-by: Youling Tang <tangyouling@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
When I update the latest kernel on the Loongson platform used with
LS7A bridge chip, the serial console has no output, this is because
the machine uses LS7A UART0 instead of CPU UART0, add UART node for
LS7A PCH to enhance the compatibility.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
To clean up mach-* directories move external declaration of malta_dt_shim()
to mips-boards/malta.h and remove malta-dtshim.h.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Move HEART specific parts of mach-ip30/irq.h to asm/sgi/heart.h and IP30
specific parts to sgi-ip30/ip30-common.h.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Loongson-3 has 16-bytes load/store instructions: gslq and gssq. This
patch calculate ra properly when unwinding the stack, if ra is saved
by gssq and restored by gslq.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Loongson-3's COP2 is Multi-Media coprocessor, it is disabled in kernel
mode by default. However, gslq/gssq (16-bytes load/store instructions)
overrides the instruction format of lwc2/swc2. If we wan't to use gslq/
gssq for optimization in kernel, we should enable COP2 usage in kernel.
Please pay attention that in this patch we only enable COP2 in kernel,
which means it will lose ST0_CU2 when a process go to user space (try
to use COP2 in user space will trigger an exception and then grab COP2,
which is similar to FPU). And as a result, we need to modify the context
switching code because the new scheduled process doesn't contain ST0_CU2
in its THERAD_STATUS probably.
For zboot, we disable gslq/gssq be generated by toolchain.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Some processors (such as Loongson-3) need to enable CU2 in kernel mode,
current set/clear method will lose Status.CU2 during context switching,
so use save/restore method instead.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
arch/mips/kernel/branch.c:876:5: error: no previous prototype for '__insn_is_compact_branch' [-Werror=missing-prototypes]
Signed-off-by: Pujin Shi <shipujin.t@gmail.com>
Signed-off-by: Pujin Shi <shipj@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
This addresses the following sparse warning:
arch/mips/kernel/setup.c:446:33: warning: symbol 'setup_elfcorehdr_size'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Currently the code for displaying a stack trace on the console is located
in traps.c rather than stacktrace.c, using the unwinding code that is in
stacktrace.c. This can be confusing and make the code hard to find since
such output is often referred to as a stack trace which might mislead the
unwary. Due to this and since traps.c doesn't interact with this code
except for via the public interfaces move the code to stacktrace.c to
make it easier to find.
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200921122341.11280-1-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Commit 73f3816609 ("arm64: Advertise mitigation of Spectre-v2, or lack
thereof") changed the way we deal with ARCH_WORKAROUND_1, by moving most
of the enabling code to the .matches() callback.
This has the unfortunate effect that the workaround gets only enabled on
the first affected CPU, and no other.
In order to address this, forcefully call the .matches() callback from a
.cpu_enable() callback, which brings us back to the original behaviour.
Fixes: 73f3816609 ("arm64: Advertise mitigation of Spectre-v2, or lack thereof")
Cc: <stable@vger.kernel.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
We seem to be pretending that we don't have any firmware mitigation
when KVM is not compiled in, which is not quite expected.
Bring back the mitigation in this case.
Fixes: 4db61fef16 ("arm64: kvm: Modernize __smccc_workaround_1_smc_start annotations")
Cc: <stable@vger.kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
The current version of the macro "for" is not able to work when the
counter is used to generate registers using mnemonics. This is because
gas is not able to evaluate the expression generated if used in
register's name (i.e x\n).
Gas offers a way to evaluate macro arguments by using % in front of
them under the alternate macro mode.
The implementation of "for" is updated to use the alternate macro mode
and %, so we can use the macro in more cases. As the alternate macro
mode may have side-effects, this is disabled when expanding the body.
While it is enough to prefix the argument of the macro "__for_body"
with %, the arguments of "__for" are also prefixed to get a more
bearable value in case of compilation error.
Suggested-by: Dave Martin <dave.martin@arm.com>
Signed-off-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Dave Martin <Dave.Martin@arm.com>
Link: https://lore.kernel.org/r/20200828181155.17745-4-broonie@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
The watchdog driver for MT8183 relies on DT data, so the fallback
compatible MT6589 won't work, need to update watchdog device node
to sync with watchdog dt-binding document.
Signed-off-by: Crystal Guo <crystal.guo@mediatek.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Pull kvm fixes from Paolo Bonzini:
"ARM:
- fix fault on page table writes during instruction fetch
s390:
- doc improvement
x86:
- The obvious patches are always the ones that turn out to be
completely broken. /me hangs his head in shame"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
Revert "KVM: Check the allocation of pv cpu mask"
KVM: arm64: Remove S1PTW check from kvm_vcpu_dabt_iswrite()
KVM: arm64: Assume write fault on S1PTW permission fault on instruction fetch
docs: kvm: add documentation for KVM_CAP_S390_DIAG318
We intend to use one header file for SERDES MUX for all
TI SoCs so rename the header file.
The exsting macros are too generic. Prefix them with SoC name.
While at that, add the missing configurations for completeness.
Fixes: b766e3b0d5 ("arm64: dts: ti: k3-j721e-main: Add system controller node and SERDES lane mux")
Reported-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Peter Rosin <peda@axentia.se>
Link: https://lore.kernel.org/r/20200918165930.2031-1-rogerq@ti.com
