Currently both the oscillator and the PLL are powered up in
set_bias_level. This can be problematic when using output clocks from
the wm8804 for other devices. The snd_soc_codec_set_pll API defines that
a clock should be available once the call returns, however, with all the
clocking controlled in set_bias_level this is not currently the case.
This patch enables pm_runtime for the wm8804, enabling both the
regulators and the oscillator when the chip resumes, and enabling the
PLL in the snd_soc_codec_set_pll call. Naturally the enabling the PLL
will also cause the chip to resume.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change converts the driver to use DAPM to control the power for the
various blocks on the chip. As part of this change the existing controls
"TX Playback Switch" (controlled power for the SPDIF TX block) and "AIF
Playback Switch" (controlled power for the AIF block) are both removed,
as they are now redundant since the power state of those blocks is
controlled automatically by DAPM.
There are several benefits of this change, the most important of which
is this change adds support for powering down the SPDIF RX block. The RX
block will automatically assume control of the PLL on the chip when it
is receiving a signal, so leaving this enabled all the time as was
currently done in the driver can be problematic. An incoming SPDIF signal
that is not being used can completely destroy the clocking for an in use
TX signal. But this change ensures that the RX block will only be
powered when the user intends to be receiving data, thus avoiding this
issue.
Additional benefits include the chip being simpler to operate as the
power no longer needs to be manually controlled between use-cases and a
small power saving (although it is acknowledged that this is likely
unimportant in the typical use-cases for this chip).
Signed-off-by: Sapthagiri Baratam <sapthagiri.baratam@incubesol.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is best to use the physical reset if it is available. This patch adds
support for a GPIO controlled physical reset for the chip.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The earpiece on wm5102 is mono, thus there is no output 3R. Don't toggle
the volume update bits for this output, although worth noting that doing
so had no negative effects it is just redundant.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The delay time after a reset in the codec probe callback was too short,
and did not work on certain hw because the codec needs more time to
power on. This increases the delay time from 1us to 1ms.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The wm8350 driver is the last driver that still uses the delayed_work field
from the snd_soc_dapm_context struct. Moving this over to the driver's
private data struct will allow us to remove the field from the DAPM context,
which will drastically reduce its size.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When being powered on, either initially on probe or when resuming from
suspend, the wm8971 configures the device for quick output capacitor
charging. Since the charging can take a rather long time (up to multiple
seconds) it is done asynchronously without blocking. A delayed work item is
run once the charging is finished and the device is switched to the target
bias level.
This all done asynchronously to the regular DAPM sequence accessing the same
data structures and registers without any looking, which can lead to race
conditions. Furthermore this potentially delays the start of stream on the
CODEC while the rest of the system is already up and running, meaning the
first bytes of audio are lost. It also does no comply with the assumption of
the DAPM core that if set_bias_level() returned successfully the device will
be at the requested bias level.
This patch slightly refactors things and makes sure that the caps charging
is properly integrated into the DAPM sequence. When transitioning from
SND_SOC_BIAS_OFF to SND_SOC_BIAS_STANDBY the part will be put into fast
charging mode and a work item will be scheduled that puts it back into
standby charging once the charging period has elapsed. If a playback or
capture stream is started while charging is in progress the driver will now
wait in SND_SOC_BIAS_PREPARE until the charging is done. This makes sure
that charging is done asynchronously in the background when the chip is
idle, but at the same time makes sure that playback/capture is not started
before the charging is done.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When being powered on, either initially on probe or when resuming from
suspend, the wm8971 configures the device for quick output capacitor
charging. Since the charging can take a rather long time (up to multiple
seconds) it is done asynchronously without blocking. A delayed work item is
run once the charging is finished and the device is switched to the target
bias level.
This all done asynchronously to the regular DAPM sequence accessing the same
data structures and registers without any looking, which can lead to race
conditions. Furthermore this potentially delays the start of stream on the
CODEC while the rest of the system is already up and running, meaning the
first bytes of audio are lost. It also does no comply with the assumption of
the DAPM core that if set_bias_level() returned successfully the device will
be at the requested bias level.
This patch slightly refactors things and makes sure that the caps charging
is properly integrated into the DAPM sequence. When transitioning from
SND_SOC_BIAS_OFF to SND_SOC_BIAS_STANDBY the part will be put into fast
charging mode and a work item will be scheduled that puts it back into
standby charging once the charging period has elapsed. If a playback or
capture stream is started while charging is in progress the driver will now
wait in SND_SOC_BIAS_PREPARE until the charging is done. This makes sure
that charging is done asynchronously in the background when the chip is
idle, but at the same time makes sure that playback/capture is not started
before the charging is done.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The delayed work used by the wm8971 driver to manage the caps charging
doesn't have any special requirements that would justify using a custom
workqueue, just use the generic system_power_efficient_wq instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Chanwoo writes:
Update extcon for v4.1
This patchset include two new extcon driver and fix minor issue of extcon
driver.
Detailed description for patchset:
1. new extcon-max77843.c and extcon-usb-gpio.c extcon driver
- extcon-max77843.c driver support the MAXIM MAX77843 MUIC (Micor-USB Interface
Controller) device which handles the various external connectors such as TA/USB
/USB-HOST/JIG and so on.
- extcon-usb-gpio.c driver support the USB and USB-HOST cable detection by
using the GPIO pin which is connected to USB ID pin. This GPIO pin updates the
USB cable states.
2. Rename the filename of extcon core driver and add missing locking mechanism
- Rename the previous extcon-class driver.c as extcon.c because '-class'
postfix is not necessary word.
- extcon core driver (extcon.c) used the raw_notifier_chain. It must be
protected by locking mechanism to avoid the list changing while
extcon_update_state() is executed.
3. Fix minor issue of extcon drviers
- Fix cable name by using the capital letter instead of small letter on
extcon-max77693.c driver.
- Clean-up code of extcon-arizona.c to detect headphone cable.
- Fix the wrong return type and variable type on extcon-max77843.c.
- Fix the checkpatch warning of all extcon drivers.
This driver will set RT5645_DEPOP_MAN bit in headphone power up
depop process. We need to restore it in headphone power down
process. Otherwise, we will get headphone noise when push button
function is enabled.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In codec bias level off, we need to disable gate mode with MCLK
for power saving. It is set by one bit. We don't need to write
while register for that.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5645 doesn't support auto incrementing writes so driver should set
the use_single_rw flag for regmap.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5650 and rt5645 use different register bits for format configuration.
This patch modifies rt5645_hw_params and rt5645_set_dai_fmt to support
both codecs.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The WM8741 DAC supports the following typical audio sampling rates:
44.1kHz, 88.2kHz, 176.4kHz (eg: with a master clock of 22.5792MHz)
32kHz, 48kHz, 96kHz, 192kHz (eg: with a master clock of 24.576MHz)
For the rates lists, we should use 82000 instead of 88235, 176400
instead of 1764000 and 192000 instead of 19200 (seems to be a typo).
Signed-off-by: Sergej Sawazki <ce3a@gmx.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
It is worth to check the regmap_read result for ID check since it
is the first regmap_read. And we can check if there is any i2c
issue.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently GPIO4 is hardcoded to output the pll-lock signal.
Unfortunately this is after the pll-out GPIO is configured which
is selectable in the device tree. Therefore it is not possible to
use GPIO4 for pll-out. Therefore this patch removes the
configuration of GPIO4.
Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
If den=1 and pllin_rate>20MHz then den and num are adjusted to 0
causing a divide by zero error a few lines further on. Therefore
this patch correctly scales num and den such that
pllin_rate/den < 20MHz as required in the device data sheet.
Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk>
Signed-off-by: Mark Brown <broonie@sirena.org.uk>
Cc: stable@vger.kernel.org
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is to ensure that 'alsactl restore' does not apply default
initialisation as the chip reset defaults are preferred.
Signed-off-by: Howard Mitchell <hm@hmbedded.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Constify local structures (snd_soc_dai_ops, snd_soc_codec_driver,
regmap_config) and array (reg_defaults) which are not modified by the
driver and passed to core as pointer to const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It needs DAC -> Playback route instead of direct settings via
SND_SOC_DAPM_DAC. otherwise, it can't find correct path if
sound card used prefix name
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value for the bias_level is SND_SOC_BIAS_OFF when probe is being
called, there is no need to initialize it explicitly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The default value for the bias_level is SND_SOC_BIAS_OFF when probe is being
called, there is no need to initialize it explicitly.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch defines an API to select the clock source for specified filters.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove adc stereo2 filter since it is not in rt5645/rt5650 codec.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5650 and rt5645 use different register bits for TDM configuration.
This patch modifies rt5645_set_tdm_slot to support both codecs.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The codec field of the snd_soc_widget struct is eventually going to be
removed, use snd_soc_dapm_to_codec(w->dapm) instead.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL_GPL;
@@
-EXPORT_SYMBOL_GPL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
We force enable "Mic Det Power" when a jack is inserted. Also, we
set codec idle_bias_off = true. As a result, codec driver will not
suspend as we expect.
On Braswell, we don't need the jack detection when suspend but need
it after resume, so export the jack suspend/resume APIs which are
provided for machine driver to control during suspend/resume.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the IRQ function support of rt5670. We use a flag
named dev_gpio in platform data to inform codec driver if the IRQ
function is used or not. Also, we export rt5670_set_jack_detect
for machine driver to pass the jack point.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
The correct values referred by a boolean control are
value.integer.value[], not value.enumerated.item[].
The former is long while the latter is int, so it's even incompatible
on 64bit architectures.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: <stable@vger.kernel.org>
