Pull USB fixes from Greg KH:
"Here are some USB and PHY fixes for 4.2-rc6 that resolve some reported
issues.
All of these have been in the linux-next tree for a while, full
details on the patches are in the shortlog below"
* tag 'usb-4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
ARM: dts: dra7: Add syscon-pllreset syscon to SATA PHY
drivers/usb: Delete XHCI command timer if necessary
xhci: fix off by one error in TRB DMA address boundary check
usb: udc: core: add device_del() call to error pathway
phy: ti-pipe3: i783 workaround for SATA lockup after dpll unlock/relock
phy-sun4i-usb: Add missing EXPORT_SYMBOL_GPL for sun4i_usb_phy_set_squelch_detect
USB: sierra: add 1199:68AB device ID
usb: gadget: f_printer: actually limit the number of instances
usb: gadget: f_hid: actually limit the number of instances
usb: gadget: f_uac2: fix calculation of uac2->p_interval
usb: gadget: bdc: fix a driver crash on disconnect
usb: chipidea: ehci_init_driver is intended to call one time
USB: qcserial: Add support for Dell Wireless 5809e 4G Modem
USB: qcserial/option: make AT URCs work for Sierra Wireless MC7305/MC7355
Kishon writes:
phy: for 4.2-rc6
*) Fix compiler error when sun4i usb phy driver is built as module
*) Fix SATA Lockup issue in dra7 SoC
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
This register is required to be passed to the SATA PHY driver
to workaround errata i783 (SATA Lockup After SATA DPLL Unlock/Relock).
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Pull ARM SoC fixes from Olof Johansson:
"Things are calming down nicely here w.r.t. fixes. This batch
includes two week's worth since I missed to send before -rc4.
Nothing particularly scary to point out, smaller fixes here and there.
Shortlog describes it pretty well"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: keystone: fix dt bindings to use post div register for mainpll
ARM: nomadik: disable UART0 on Nomadik boards
ARM: dts: i.MX35: Fix can support.
ARM: OMAP2+: hwmod: Fix _wait_target_ready() for hwmods without sysc
ARM: dts: add CPU OPP and regulator supply property for exynos4210
ARM: dts: Update video-phy node with syscon phandle for exynos3250
ARM: DRA7: hwmod: fix gpmc hwmod
All of the keystone devices have a separate register to hold post
divider value for main pll clock. Currently the fixed-postdiv
value used for k2hk/l/e SoCs works by sheer luck as u-boot happens to
use a value of 2 for this. Now that we have fixed this in the pll
clock driver change the dt bindings for the same.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The i.MX fixes for 4.2, 2nd round:
- Add the required second clock for i.MX35 FlexCAN in device tree,
so that the device can be probed by kernel successfully.
* tag 'imx-fixes-4.2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: i.MX35: Fix can support.
Signed-off-by: Olof Johansson <olof@lixom.net>
The UART0 is not used on these boards, yet active and blocking
other use. Fix this by disabling UART0 and setting port aliases
to maintain port enumeration to userspace.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Since commit 3d42a379b6
("can: flexcan: add 2nd clock to support imx53 and newer")
the can driver requires a dt nodes to have a second clock.
Add them to imx35 to fix probing the flex can driver on the
respective platforms.
Signed-off-by: Denis Carikli <denis@eukrea.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
cd-gpios polarity should be changed to GPIO_ACTIVE_LOW and wp-gpios
should be changed to GPIO_ACTIVE_HIGH.
Otherwise, the SD may not work properly due to wrong polarity inversion
specified in DT after switch to common parsing function mmc_of_parse().
Signed-off-by: Dong Aisheng <aisheng.dong@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Merge "Samsung fixes for v4.2" from Kukjin Kim:
From Krzysztof Kozlowski:
1. Fix exynos3250 MIPI DSI display and MIPI CSIS-2 camera sensorx
after adding support for PMU regmap in exynos-video-mipi driver
(issue introduced in v4.0).
2. Bring back cpufreq for exynos4210 after incomplete switch to
cpufreq-dt driver in 4.2 merge window. The necessary DT changes
for exynos4210 cpufreq was not applied to the same tree as rest
of patchset because of multiple conflicts between clk and arm-soc
trees. Unfortunately without the change the exynos4210 boards
loose cpufreq feature.
* tag 'samsung-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add CPU OPP and regulator supply property for exynos4210
ARM: dts: Update video-phy node with syscon phandle for exynos3250
Signed-off-by: Olof Johansson <olof@lixom.net>
As a follow-up to recent changes to Exynos mipi video phy driver,
introducing support for PMU regmap in commit e4b3d38088 ("phy:
exynos-video-mipi: Fix regression by adding support for PMU regmap")
add a syscon phandle to video-phy node to bring back to life both
MIPI DSI display and MIPI CSIS-2 camera sensor on Exynos3250.
Signed-off-by: Beata Michalska <b.michalska@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Pull ARM SoC fixes from Olof Johansson:
"By far most of the fixes here are updates to DTS files to deal with
some mostly minor bugs.
There's also a fix to deal with non-PM kernel configs on i.MX, a
regression fix for ethernet on PXA platforms and a dependency fix for
OMAP"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
ARM: pxa: fix dm9000 platform data regression
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
MAINTAINERS: digicolor: add dts files
ARM: ux500: fix MMC/SD card regression
ARM: ux500: define serial port aliases
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
ARM: dts: omap3: overo: Update LCD panel names
ARM: dts: cros-ec-keyboard: Add support for some Japanese keys
ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
ARM: dts: imx53-qsb: fix TVE entry
ARM: dts: mx23: fix iio-hwmon support
ARM: dts: imx27: Adjust the GPT compatible string
ARM: socfpga: dts: Fix entries order
ARM: socfpga: dts: Fix adxl34x formating and compatible string
Merge "ARM: Couple of dts fixes for v4.2-rcx" from Santosh Shilimkar:
Couple of DTS fixes 4.2-rcx for Keystone EVMs:
K2E EVM boot hangs because of missing serdes driver which is needed to bring up
PCIe on K2E. These couple of fixes makes the PCIE disabled on common default and
let the specific board DTS to enable it.
* tag 'keystone-dts-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: keystone: dts: rename pcie nodes to help override status
ARM: keystone: dts: fix dt bindings for PCIe
Signed-off-by: Olof Johansson <olof@lixom.net>
Now that PCIe DT binding is disabled in SoC specific DTS,
we need a way to override it in a board specific DTS. So
rename the PCIe nodes accordingly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Currently PCIe DT bindings are broken. PCIe driver can't function
without having a SerDes driver that provide the phy configuration.
On K2E EVM, this causes problem since the EVM has Marvell SATA
controller present and with default values in the SerDes register,
it seems to pass the PCIe link check, but causes issues since
the configuration is not correct. The manifestation is that when
EVM is booted with NFS rootfs, the boot hangs. We shouldn't enable
PCIe on this EVM since to work, SerDes driver has to be present as
well. So by default, the PCIe DT binding should be disabled in SoC
specific DTS. It can be enabled in the board specific DTS when the
SerDes device driver is also present.
So fix the status of PCIe DT bindings in the SoC specific DTS to
"disabled". To enable PCIe, the status should be set to "ok" in
the EVM DTS file when SerDes driver support becomes available in
the upstream tree.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Fixes for omaps, all dts changes except for one:
- Fix up LCD panel name for overo boards
- Three fixes for pepper board for regulators, freqeuncy
scaling and audio input. Note that there is still one
issue being worked on for booting with multi_v7_defconfig
- Add missing #iommu-cells for omap4 and 5
- Add missing HAVE_ARM_SCU for am43xx
* tag 'omap-for-v4.2/fixes-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (210 commits)
ARM: dts: Correct audio input route & set mic bias for am335x-pepper
ARM: OMAP2+: Add HAVE_ARM_SCU for AM43XX
ARM: dts: OMAP5: Add #iommu-cells property to IOMMUs
ARM: dts: OMAP4: Add #iommu-cells property to IOMMUs
ARM: dts: Fix frequency scaling on Gumstix Pepper
ARM: dts: configure regulators for Gumstix Pepper
ARM: dts: omap3: overo: Update LCD panel names
+ Linux 4.2-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
Audio-in was incorrectly routed to Line In. It should be Mic3L as per
schematic.
Using mic-bias voltage at 2.0v (<0x1>) does not work for some reason. There
is no voltage seen on micbias (R127). Mic-bias voltage of 2.5v (<0x2>) works.
I see voltage of 2.475v across GND and micbias.
With these changes, I can record audio with a pair of proliferate TRRS earbuds.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Acked-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Merge "ARM: imx: fixes for 4.2" from Shawn Guo:
The i.MX fixes for 4.2:
- Correct compatible string for i.MX27 GPT which actually shares the
same programming model as i.MX21 GPT rather than i.MX1 one.
- Add missing #io-channel-cells property for i.MX23 LRADC device, which
is required for the device to be an IIO provider.
- Correct HSYNC/VSYNC pins and add ddc-i2c-bus property for TVE device
on imx53-qsb to work properly.
- Always enable PU domain if CONFIG_PM is not set. This fixes a couple
of failure scenarios which will hang the system if one of the devices
in the PU domain is accessed.
* tag 'imx-fixes-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx6: gpc: always enable PU domain if CONFIG_PM is not set
ARM: dts: imx53-qsb: fix TVE entry
ARM: dts: mx23: fix iio-hwmon support
ARM: dts: imx27: Adjust the GPT compatible string
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "SoCFPGA fixes for v4.2-rc1" from Dinh Nguyen:
SoCFPGA fixes against v4.2-rc1
- Update compatible "adxl345x" compatible string
- Alphabetize the DTS nodes for the C5 sockit board file
* tag 'socfpga_fixes_for_v4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: socfpga: dts: Fix entries order
ARM: socfpga: dts: Fix adxl34x formating and compatible string
Ux500 is regressing due to commit
a21763a0b1
"pinctrl: nomadik: activate strict mux mode" which disallows
Nomadik GPIO 5 to be muxed in as a level shifter voltage select
pin, as it is currently described as being used for RX on UART1.
The behaviour is correct, instead the hardware config has been
incorrecly specified: UART1 is indeed unused on HREFv60plus and
Snowball and that is why HREFv60plus can use the pins it would
normally occupy as the voltage select line for the MMC/SD
levelshifter (Snowball uses it for I2C4).
The reason UART1 was anyway enabled on these platforms was
probably to secure the port enumeration to userspace. This
can be solved by using aliases (done in a separate patch) so
we can now deactivate UART1 and let MMC/SD use it properly
on HREFv60plus. We explicitly activate it only for the
older HREFprev60 board.
To complete, we set up the pin configuration for these pins
properly in the sdi0 node.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This enumerates the PL011 serial ports on the Ux500. This is
necessary to do if we want to remove one of the serial ports,
since userspace depends on console to be present on ttyAMA2
and we must not break userspace.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP5 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing #iommu-cells property to the DSP and IPU IOMMU nodes
for OMAP4 platforms. This property is required as per the generic
iommu binding.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The device tree for Gumstix Pepper has DCDC2 and
DCDC3 correctly labelled but the upper limit values
are wrong. The confusion is due to the hardware
quirk where the DCDC2 and DCDC3 wires are flipped
in Pepper.
Signed-off-by: Arun Bharadwaj <arun@gumstix.com>
Tested-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Boot process is halting in midway because some of the necessary voltage
regulators are deemed unused and subsequently powered off, leading to
a completely unresponsive system.
Most of the device nodes had correct voltage regulator attachments.
Yet these nodes had to set stricter enforcement on them through
'regulator-boot-on' and 'regulator-always-on' to function correctly.
The consumers of the regulators this commit affect are the followings:
DCDC1: vdd_1v8 system supply, USB-PHY, and ADC
DCDC2: Core domain
DCDC3: MPU core domain
LDO1: RTC
LDO2: 3v3 IO domain
LDO3: USB-PHY; not a boot-time requirement
LDO4: LCD [16:23]
All but LDO3 need to be always-on for the system to be functional.
Additionally regulator-name properties have been added for the kernel to
display the name from the schematic. This will improve diagnostics.
Signed-off-by: Adam YH Lee <adam.yh.lee@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
For Gumstix Overo COMs, the u-boot bootloader typically passes an
argument specifying the default display via the omapdss.def_disp
parameter. When a default display is specified, DSS2 tries to match
this name with either the device tree label (e.g. label=dvi) or,
failing this, the device tree alias (e.g. label=display0). Update the
panel names for the 'lcd43' and 'lcd35' displays in the device tree
such that they match the names passed by u-boot.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull networking fixes from David Miller:
1) Missing list head init in bluetooth hidp session creation, from Tedd
Ho-Jeong An.
2) Don't leak SKB in bridge netfilter error paths, from Florian
Westphal.
3) ipv6 netdevice private leak in netfilter bridging, fixed by Julien
Grall.
4) Fix regression in IP over hamradio bpq encapsulation, from Ralf
Baechle.
5) Fix race between rhashtable resize events and table walks, from Phil
Sutter.
6) Missing validation of IFLA_VF_INFO netlink attributes, fix from
Daniel Borkmann.
7) Missing security layer socket state initialization in tipc code,
from Stephen Smalley.
8) Fix shared IRQ handling in boomerang 3c59x interrupt handler, from
Denys Vlasenko.
9) Missing minor_idr destroy on module unload on macvtap driver, from
Johannes Thumshirn.
10) Various pktgen kernel thread races, from Oleg Nesterov.
11) Fix races that can cause packets to be processed in the backlog even
after a device attached to that SKB has been fully unregistered.
From Julian Anastasov.
12) bcmgenet driver doesn't account packet drops vs. errors properly,
fix from Petri Gynther.
13) Array index validation and off by one fix in DSA layer from Florian
Fainelli
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (66 commits)
can: replace timestamp as unique skb attribute
ARM: dts: dra7x-evm: Prevent glitch on DCAN1 pinmux
can: c_can: Fix default pinmux glitch at init
can: rcar_can: unify error messages
can: rcar_can: print request_irq() error code
can: rcar_can: fix typo in error message
can: rcar_can: print signed IRQ #
can: rcar_can: fix IRQ check
net: dsa: Fix off-by-one in switch address parsing
net: dsa: Test array index before use
net: switchdev: don't abort unsupported operations
net: bcmgenet: fix accounting of packet drops vs errors
cdc_ncm: update specs URL
Doc: z8530book: Fix typo in API-z8530-sync-txdma-open.html
net: inet_diag: always export IPV6_V6ONLY sockopt for listening sockets
bridge: mdb: allow the user to delete mdb entry if there's a querier
net: call rcu_read_lock early in process_backlog
net: do not process device backlog during unregistration
bridge: fix potential crash in __netdev_pick_tx()
net: axienet: Fix devm_ioremap_resource return value check
...
Driver core sets "default" pinmux on on probe and CAN driver
sets "sleep" pinmux during register. This causes a small window
where the CAN pins are in "default" state with the DCAN module
being disabled.
Change the "default" state to be like sleep so this glitch is
avoided. Add a new "active" state that is used by the driver
when CAN is actually active.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Merge "omap fixes against v4.2-rc1" from Tony Lindgren:
Minor fixes for omaps against v4.2-rc1. Mostly just minor dts changes
except for a GPMC fix to not use names for probing devices. Also a
one liner clean-up to remove unecessary return from a void function.
The summary for the changes being:
- Fix probe for GPMC devices by reoving limitations based on device
name
- Remove unnecessary return from a void function
- Revert beaglebone RTC sleep fix, we now have a better fix merged
- Add am4372 EMIF node to fix a warning
- Add am57xx-beagle-x15 power supply to fix USB2 if USB1 is disabled
- Disable rfbi for am4372 as it does not have a driver
* tag 'omap-for-v4.2/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am4372.dtsi: disable rfbi
ARM: dts: am57xx-beagle-x15: Provide supply for usb2_phy2
ARM: dts: am4372: Add emif node
Revert "ARM: dts: am335x-boneblack: disable RTC-only sleep"
ARM: OMAP2+: Remove unnessary return statement from the void function, omap2_show_dma_caps
memory: omap-gpmc: Fix parsing of devices
The CCI device node was added to vexpress CA15_A7(i.e. TC2) much before
the CCI PMU support and binding was added. This patch adds the missing
PMU node so that CCI PMUs can be used on TC2.
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Punit Agrawal <punit.agrawal@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
The dts for the CoreTile Express A15x2 A7x3 (TC2) only describes the
PMUs of the Cortex-A15 CPUs, and not the Cortex-A7 CPUs.
Now that we have a mechanism for describing disparate PMUs and their
interrupts in device tree, this patch makes use of these to describe the
PMUs for all CPUs in the system. For consistency, the existing A15 PMU
interrupt-affinity property is reflowed across two lines.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Merge "CSR atlas7 pinctrl descriptions for 4.2" from Barry Song:
add atlas7 pinctrl dts stuff
add atlas7 pin groups and gpio/pin mapping descriptions
* tag 'atlas7-pinctrl-dts-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux:
ARM: dts: atlas7: add pinctrl and gpio descriptions
include/soc/imx/timer.h describes well the different versions of
the GPT block among the imx family:
enum imx_gpt_type {
GPT_TYPE_IMX1, /* i.MX1 */
GPT_TYPE_IMX21, /* i.MX21/27 */
GPT_TYPE_IMX31, /* i.MX31/35/25/37/51/6Q */
GPT_TYPE_IMX6DL, /* i.MX6DL/SX/SL */
};
So the proper compatible string for the MX27 case should be
"fsl,imx21-gpt".
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch fixes the formating of DTS bindings for the adxl34x digital
accelerometer, and updates the compatible string after the deprecation
of "adxl345x" compatible string.
Signed-off-by: Walter Lozano <walter@vanguardiasur.com.ar>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
When DSS nodes were added to am4372.dtsi, the rfbi node was not marked
as disabled. This should have been done, as the rule of thumb is to
disable all DSS nodes that are not used, and especially rfbi, as we
don't have a driver for rfbi.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this USB2 breaks if USB1 is disabled or USB1
initializes after USB2 e.g. due to deferred probing.
Fixes: 5a0f93c657 ("ARM: dts: Add am57xx-beagle-x15")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Cc: stable@vger.kernel.org (v3.19+)
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node for TI AM4372 EMIF. Without this we get a warning with the
recent commit fabbe6df (ARM: OMAP: AM43xx hwmod: Add data for am43xx
emif hwmod).
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
[tony@atomide.com: updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 3d76be5b93.
The latest revision of Beaglebone Black does not support RTC-only mode.
To avoid potential hardware damage, RTC-only mode was disabled by
default by commit 7a6cb0abe1 ("ARM: dts: am335x-boneblack: disable
RTC-only sleep to avoid hardware damage").
Unfortunately, an incorrect fix had already been applied, which instead
of just disabling RTC-only mode, prevents the Beaglebone from powering
down at all.
Revert this patch to fix the power-off regression.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pull ARM SoC late fixes and dependencies from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
Other than the fixes, the primary feature being added is the
conversion of some OMAP drivers to the new generic wakeirq interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: multi_v7_defconfig: Enable BRCMNAND driver
ARM: BCM: Do not select CONFIG_MTD_NAND_BRCMNAND
ARM: at91/dt: update udc compatible strings
ARM: at91/dt: trivial: fix USB udc compatible string
arm64: dts: Add APM X-Gene standby GPIO controller DTS entries
soc: qcom: spm: Fix idle on THUMB2 kernels
ARM: dove: fix legacy dove IRQ numbers
ARM: mvebu: fix suspend to RAM on big-endian configurations
ARM: mvebu: adjust Armada XP DT spi muxing after pinctrl function rename
serial: 8250_omap: Move wake-up interrupt to generic wakeirq
serial: omap: Switch wake-up interrupt to generic wakeirq
mmc: omap_hsmmc: Change wake-up interrupt to use generic wakeirq
Pull clock framework updates from Michael Turquette:
"The changes to the common clock framework for 4.2 are dominated by new
drivers and updates to existing ones, as usual.
There are some fixes to the framework itself and several cleanups for
sparse warnings, etc"
* tag 'clk-for-linus-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (135 commits)
clk: stm32: Add clock driver for STM32F4[23]xxx devices
dt-bindings: Document the STM32F4 clock bindings
cpufreq: exynos: remove Exynos4210 specific cpufreq driver support
ARM: Exynos: switch to using generic cpufreq driver for Exynos4210
clk: samsung: exynos4: add cpu clock configuration data and instantiate cpu clock
clk: samsung: add infrastructure to register cpu clocks
clk: add CLK_RECALC_NEW_RATES clock flag for Exynos cpu clock support
doc: dt: add documentation for lpc1850-ccu clk driver
clk: add lpc18xx ccu clk driver
doc: dt: add documentation for lpc1850-cgu clk driver
clk: add lpc18xx cgu clk driver
clk: keystone: add support for post divider register for main pll
clk: mvebu: flag the crypto clk as CLK_IGNORE_UNUSED
clk: cygnus: remove Cygnus dummy clock binding
clk: cygnus: add clock support for Broadcom Cygnus
clk: Change bcm clocks build dependency
clk: iproc: add initial common clock support
clk: iproc: define Broadcom iProc clock binding
MAINTAINERS: update email for Michael Turquette
clk: meson: add some error handling in meson_clk_register_cpu()
...
