Pull thermal management updates from Zhang Rui:
- add thermal driver for R-Car Gen3 thermal sensors.
- add thermal driver for ZTE' zx2967 family thermal sensors.
- convert thermal ID allocation from IDR to IDA.
- fix a possible NULL dereference in imx thermal driver.
- fix a ti-soc-thermal driver dependency issue so that critical thermal
control is still available when CPU_THERMAL is not defined.
- update binding information for QorIQ thermal driver.
- a couple of cleanups in thermal core, intel_powerclamp, exynos,
dra752-thermal, mtk-thermal driver.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
powerpc/mpc85xx: Update TMU device tree node for T1023/T1024
powerpc/mpc85xx: Update TMU device tree node for T1040/T1042
dt-bindings: Update QorIQ TMU thermal bindings
thermal: mtk_thermal: Staticise a number of data variables
thermal: arm: dra752: Remove all TSHUT related definitions
thermal: arm: dra752: Remove TSHUT configuration
thermal: ti-soc-thermal: Remove CPU_THERMAL Dependency from TI_THERMAL
thermal: imx: Fix possible NULL dereference.
thermal: exynos: Remove parsing unused samsung,tmu_cal_mode property
thermal: zx2967: add thermal driver for ZTE's zx2967 family
thermal: use cpumask_var_t for on-stack cpu masks
dt: bindings: add documentation for zx2967 family thermal sensor
thermal/intel_powerclamp: Remove set-but-not-used variables
thermal: rcar_gen3_thermal: Add R-Car Gen3 thermal driver
thermal: rcar_gen3_thermal: Document the R-Car Gen3
thermal: convert devfreq_cooling to use an IDA
thermal: convert cpu_cooling to use an IDA
thermal: convert clock cooling to use an IDA
thermal core: convert ID allocation to IDA
Pull pwm updates from Thierry Reding:
"This set contains mostly fixes to existing drivers as well as cleanup
of code that's not been in active use for a while"
* tag 'pwm/for-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (27 commits)
acpi: lpss: call pwm_add_table() for BSW PWM device
pwm: Try to load modules during pwm_get()
pwm: Don't hold pwm_lookup_lock longer than necessary
pwm: Make the PWM_POLARITY flag in DTB optional
pwm: Print error messages with pr_err() instead of pr_debug()
pwm: imx: Add polarity inversion support to i.MX's PWMv2
pwm: imx: doc: Update imx-pwm.txt documentation entry
pwm: imx: Remove redundant i.MX PWMv2 code
pwm: imx: Provide atomic PWM support for i.MX PWMv2
pwm: imx: Move PWMv2 wait for fifo slot code to a separate function
pwm: imx: Move PWMv2 software reset code to a separate function
pwm: imx: Rewrite v1 code to facilitate switch to atomic PWM
pwm: imx: Add separate set of PWM ops for v1 and v2
pwm: imx: Remove ipg clock and enable per clock when required
pwm: lpss: Add Intel Gemini Lake PCI ID
pwm: lpss: Do not export board infos for different PWM types
pwm: lpss: Avoid reconfiguring while UPDATE bit is still enabled
pwm: lpss: Switch to new atomic API
pwm: lpss: Allow duty cycle to be 0
pwm: lpss: Avoid potential overflow of base_unit
...
Pull IPMI updates from Corey Minyard:
"This is a few small fixes to the main IPMI driver, make some things
const, fix typos, etc.
The last patch came in about a week ago, but IMHO it's best to go in
now. It is not for the main driver, it's for the bt-bmc driver, which
runs on the managment controller side, not on the host side, so the
scope is limited and the change is necessary"
* tag 'for-linus-4.11' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: bt-bmc: Use a regmap for register access
char: ipmi: constify ipmi_smi_handlers structures
acpi:ipmi: Make IPMI user handler const
ipmi: make ipmi_usr_hndl const
Documentation: Fix a typo in IPMI.txt.
Pull ceph updates from Ilya Dryomov:
"This time around we have:
- support for rbd data-pool feature, which enables rbd images on
erasure-coded pools (myself). CEPH_PG_MAX_SIZE has been bumped to
allow erasure-coded profiles with k+m up to 32.
- a patch for ceph_d_revalidate() performance regression introduced
in 4.9, along with some cleanups in the area (Jeff Layton)
- a set of fixes for unsafe ->d_parent accesses in CephFS (Jeff
Layton)
- buffered reads are now processed in rsize windows instead of rasize
windows (Andreas Gerstmayr). The new default for rsize mount option
is 64M.
- ack vs commit distinction is gone, greatly simplifying ->fsync()
and MOSDOpReply handling code (myself)
... also a few filesystem bug fixes from Zheng, a CRUSH sync up (CRUSH
computations are still serialized though) and several minor fixes and
cleanups all over"
* tag 'ceph-for-4.11-rc1' of git://github.com/ceph/ceph-client: (52 commits)
libceph, rbd, ceph: WRITE | ONDISK -> WRITE
libceph: get rid of ack vs commit
ceph: remove special ack vs commit behavior
ceph: tidy some white space in get_nonsnap_parent()
crush: fix dprintk compilation
crush: do is_out test only if we do not collide
ceph: remove req from unsafe list when unregistering it
rbd: constify device_type structure
rbd: kill obj_request->object_name and rbd_segment_name_cache
rbd: store and use obj_request->object_no
rbd: RBD_V{1,2}_DATA_FORMAT macros
rbd: factor out __rbd_osd_req_create()
rbd: set offset and length outside of rbd_obj_request_create()
rbd: support for data-pool feature
rbd: introduce rbd_init_layout()
rbd: use rbd_obj_bytes() more
rbd: remove now unused rbd_obj_request_wait() and helpers
rbd: switch rbd_obj_method_sync() to ceph_osdc_call()
libceph: pass reply buffer length through ceph_osdc_call()
rbd: do away with obj_request in rbd_obj_read_sync()
...
Pull x86 fixes from Ingo Molnar:
"Two documentation updates, plus a debugging annotation fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/crash: Update the stale comment in reserve_crashkernel()
x86/irq, trace: Add __irq_entry annotation to x86's platform IRQ handlers
Documentation, x86, resctrl: Recommend locking for resctrlfs
Pull cgroup updates from Tejun Heo:
"Several noteworthy changes.
- Parav's rdma controller is finally merged. It is very straight
forward and can limit the abosolute numbers of common rdma
constructs used by different cgroups.
- kernel/cgroup.c got too chubby and disorganized. Created
kernel/cgroup/ subdirectory and moved all cgroup related files
under kernel/ there and reorganized the core code. This hurts for
backporting patches but was long overdue.
- cgroup v2 process listing reimplemented so that it no longer
depends on allocating a buffer large enough to cache the entire
result to sort and uniq the output. v2 has always mangled the sort
order to ensure that users don't depend on the sorted output, so
this shouldn't surprise anybody. This makes the pid listing
functions use the same iterators that are used internally, which
have to have the same iterating capabilities anyway.
- perf cgroup filtering now works automatically on cgroup v2. This
patch was posted a long time ago but somehow fell through the
cracks.
- misc fixes asnd documentation updates"
* 'for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (27 commits)
kernfs: fix locking around kernfs_ops->release() callback
cgroup: drop the matching uid requirement on migration for cgroup v2
cgroup, perf_event: make perf_event controller work on cgroup2 hierarchy
cgroup: misc cleanups
cgroup: call subsys->*attach() only for subsystems which are actually affected by migration
cgroup: track migration context in cgroup_mgctx
cgroup: cosmetic update to cgroup_taskset_add()
rdmacg: Fixed uninitialized current resource usage
cgroup: Add missing cgroup-v2 PID controller documentation.
rdmacg: Added documentation for rdmacg
IB/core: added support to use rdma cgroup controller
rdmacg: Added rdma cgroup controller
cgroup: fix a comment typo
cgroup: fix RCU related sparse warnings
cgroup: move namespace code to kernel/cgroup/namespace.c
cgroup: rename functions for consistency
cgroup: move v1 mount functions to kernel/cgroup/cgroup-v1.c
cgroup: separate out cgroup1_kf_syscall_ops
cgroup: refactor mount path and clearly distinguish v1 and v2 paths
cgroup: move cgroup v1 specific code to kernel/cgroup/cgroup-v1.c
...
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- constify rtc_class_ops structures
New driver:
- STM32
Drivers:
- armada38x: fix errata, Armada 7K/8K support
- ds3232: fix wakeup support
- gemini: DT support
- m48t86: huge cleanup and platform_data removal
- mcp795: alarm support
- sun6i: proper oscillator handling
- tegra: proper clock handling
- tps65910: calibration support"
* tag 'rtc-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (44 commits)
rtc: ds3232: Call device_init_wakeup before device_register
rtc: pcf2127: bulk read only date and time registers.
rtc: armada38x: Add support for Armada 7K/8K
rtc: armada38x: Prepare driver to manage different versions
rtc: ds3232: Add regmap max_register definition.
rtc: ds3232: Cleanup whitespace around register and bit definitions.
rtc: m48t86: remove unused platform_data
ARM: Orion5x: ts78xx: allow rtc-m48t86 to manage it's own resources
ARM: Orion5x: ts78xx: remove RTC detection
ARM: ep93xx: ts72xx: allow rtc-m48t86 to manage its own resources
rtc: m48t86: verify that the RTC is actually present
rtc: m48t86: add NVRAM support
rtc: m48t86: allow driver to manage its resources
rtc: m48t86: shorten register name defines
bindings: rtc: correct wrong reference in required properties
rtc: sun6i: Fix return value check in sun6i_rtc_clk_init()
rtc: sun6i: extend test coverage
rtc: sun6i: Fix compatibility with old DT binding
rtc: snvs: add a missing write sync
rtc: bq32000: add support to enable disable the trickle charge FET bypass
...
Pull tracing updates from Steven Rostedt:
"This release has no new tracing features, just clean ups, minor fixes
and small optimizations"
* tag 'trace-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: (25 commits)
tracing: Remove outdated ring buffer comment
tracing/probes: Fix a warning message to show correct maximum length
tracing: Fix return value check in trace_benchmark_reg()
tracing: Use modern function declaration
jump_label: Reduce the size of struct static_key
tracing/probe: Show subsystem name in messages
tracing/hwlat: Update old comment about migration
timers: Make flags output in the timer_start tracepoint useful
tracing: Have traceprobe_probes_write() not access userspace unnecessarily
tracing: Have COMM event filter key be treated as a string
ftrace: Have set_graph_function handle multiple functions in one write
ftrace: Do not hold references of ftrace_graph_{notrace_}hash out of graph_lock
tracing: Reset parser->buffer to allow multiple "puts"
ftrace: Have set_graph_functions handle write with RDWR
ftrace: Reset fgd->hash in ftrace_graph_write()
ftrace: Replace (void *)1 with a meaningful macro name FTRACE_GRAPH_EMPTY
ftrace: Create a slight optimization on searching the ftrace_hash
tracing: Add ftrace_hash_key() helper function
ftrace: Convert graph filter to use hash tables
ftrace: Expose ftrace_hash_empty and ftrace_lookup_ip
...
Pull watchdog updates from Guenter Roeck:
"Wim asked me to handle the watchdog pull request this time around.
Key changes:
- New drivers: Cortina Gemini, ZTE's zx2967 family, NIC7018
- Convert to use device managed functions: ebc-c384_wdt, tegra_wdt,
da9063_wdt, da9062_wdt, da9055_wdt, da9052_wdt, bcm2835_wdt,
mena21_wdt, wm831x_wdt, digicolor_wdt, intel-mid_wdt, meson_wdt,
sunxi_wdt, aspeed_wdt, coh901327_wdt, iTCO_wdt
- Use watchdog core to install restart handler: tangox, dw_wdt,
bcm2835_wdt, asm9260_wdt, bcm47xx_wdt
- Convert ts72xx_wdt driver to watchdog core
- Let core handle heartbeat in ep93xx_wdt driver
- Enable COMPILE_TEST where possible
- Various other improvements"
* tag 'watchdog-for-linus-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (54 commits)
watchdog: s3c2410: Add prefix to local function
watchdog: s3c2410: Select MFD_SYSCON on all Exynos platforms
watchdog: s3c2410: Use dev_dbg instead of pr_info
watchdog: s3c2410: Fix infinite interrupt in soft mode
watchdog: s3c2410: Remove confusing CONFIG prefix from local defines
watchdog: softdog: make pretimeout support a compile option
watchdog: zx2967: add watchdog controller driver for ZTE's zx2967 family
dt: bindings: add documentation for zx2967 family watchdog controller
watchdog: sama5d4: Implement resume hook
watchdog: sama5d4: Cache MR instead of a partial config
watchdog: ts72xx_wdt: convert driver to watchdog core
watchdog: ep93xx_wdt: cleanup and let the core handle the heartbeat
watchdog: RDC321X_WDT always depends on PCI
watchdog: add driver for Cortina Gemini watchdog
watchdog: add DT bindings for Cortina Gemini
watchdog: constify watchdog_ops structures
watchdog: Introduce watchdog_stop_on_unregister helper
watchdog: ebc-c384_wdt: Utilize devm_ functions in driver probe callback
watchdog: tegra_wdt: Convert to use device managed functions
watchdog: da9063_wdt: Convert to use device managed functions
...
Pull Kselftest update from Shuah Khan:
"This update consists of:
- fixes to several existing tests from Stafford Horne
- cpufreq tests from Viresh Kumar
- Selftest build and install fixes from Bamvor Jian Zhang and Michael
Ellerman
- Fixes to protection-keys tests from Dave Hansen
- Warning fixes from Shuah Khan"
* tag 'linux-kselftest-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest: (28 commits)
selftests/powerpc: Fix remaining fallout from recent changes
selftests/powerpc: Fix the clean rule since recent changes
selftests: Fix the .S and .S -> .o rules
selftests: Fix the .c linking rule
selftests: Fix selftests build to just build, not run tests
selftests, x86, protection_keys: fix wrong offset in siginfo
selftests, x86, protection_keys: fix uninitialized variable warning
selftest: cpufreq: Update MAINTAINERS file
selftest: cpufreq: Add special tests
selftest: cpufreq: Add support to test cpufreq modules
selftest: cpufreq: Add suspend/resume/hibernate support
selftest: cpufreq: Add support for cpufreq tests
selftests: Add intel_pstate to TARGETS
selftests/intel_pstate: Update makefile to match new style
selftests/intel_pstate: Fix warning on loop index overflow
cpupower: Restore format of frequency-info limit
selftests/futex: Add headers to makefile dependencies
selftests/futex: Add stdio used for logging
selftests: x86 protection_keys remove dead code
selftests: x86 protection_keys fix unused variable compile warnings
...
Pull clk updates from Stephen Boyd:
"The usual collection of new drivers, non-critical fixes, and updates
to existing clk drivers. The bulk of the work is on Allwinner and
Rockchip SoCs, but there's also an Intel Atom driver in here too.
New Drivers:
- Tegra BPMP firmware
- Hisilicon hi3660 SoCs
- Rockchip rk3328 SoCs
- Intel Atom PMC
- STM32F746
- IDT VersaClock 5P49V5923 and 5P49V5933
- Marvell mv98dx3236 SoCs
- Allwinner V3s SoCs
Removed Drivers:
- Samsung Exynos4415 SoCs
Updates:
- Migrate ABx500 to OF
- Qualcomm IPQ4019 CPU clks and general PLL support
- Qualcomm MSM8974 RPM
- Rockchip non-critical fixes and clk id additions
- Samsung Exynos4412 CPUs
- Socionext UniPhier NAND and eMMC support
- ZTE zx296718 i2s and other audio clks
- Renesas CAN and MSIOF clks for R-Car M3-W
- Renesas resets for R-Car Gen2 and Gen3 and RZ/G1
- TI CDCE913, CDCE937, and CDCE949 clk generators
- Marvell Armada ap806 CPU frequencies
- STM32F4* I2S/SAI support
- Broadcom BCM2835 DSI support
- Allwinner sun5i and A80 conversion to new style clk bindings"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (130 commits)
clk: renesas: mstp: ensure register writes complete
clk: qcom: Do not drop device node twice
clk: mvebu: adjust clock handling for the CP110 system controller
clk: mvebu: Expand mv98dx3236-core-clock support
clk: zte: add i2s clocks for zx296718
clk: sunxi-ng: sun9i-a80: Fix wrong pointer passed to PTR_ERR()
clk: sunxi-ng: select SUNXI_CCU_MULT for sun5i
clk: sunxi-ng: Check kzalloc() for errors and cleanup error path
clk: tegra: Add BPMP clock driver
clk: uniphier: add eMMC clock for LD11 and LD20 SoCs
clk: uniphier: add NAND clock for all UniPhier SoCs
ARM: dts: sun9i: Switch to new clock bindings
clk: sunxi-ng: Add A80 Display Engine CCU
clk: sunxi-ng: Add A80 USB CCU
clk: sunxi-ng: Add A80 CCU
clk: sunxi-ng: Support separately grouped PLL lock status register
clk: sunxi-ng: mux: Get closest parent rate possible with CLK_SET_RATE_PARENT
clk: sunxi-ng: mux: honor CLK_SET_RATE_NO_REPARENT flag
clk: sunxi-ng: mux: Fix determine_rate for mux clocks with pre-dividers
clk: qcom: SDHCI enablement on Nexus 5X / 6P
...
Pull i2c updates from Wolfram Sang:
"I2C has for you two new drivers (Tegra BPMP and STM32F4), interrupt
support for pca954x muxes, and a bunch of driver bugfixes and
improvements. Nothing really special this cycle.
A few commits have been added to my tree just recently. Those are the
Tegra BPMP driver and a few straightforward bugfixes or cleanups which
I prefer to have upstream rather soonish. The rest had proper
linux-next exposure"
* 'i2c/for-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (25 commits)
i2c: thunderx: Replace pci_enable_msix()
i2c: exynos5: fix arbitration lost handling
i2c: exynos5: disable fifo-almost-empty irq signal when necessary
i2c: at91: ensure state is restored after suspending
i2c: bcm2835: Avoid possible NULL ptr dereference
i2c: Add Tegra BPMP I2C proxy driver
dt-bindings: Add Tegra186 BPMP I2C binding
misc: eeprom: at24: use device_property_*() functions instead of of_get_property()
i2c: mux: pca954x: Add interrupt controller support
dt: bindings: i2c-mux-pca954x: Add documentation for interrupt controller
i2c: mux: pca954x: Add missing pca9542 definition to chip_desc
i2c: riic: correctly finish transfers
i2c: i801: Add support for Intel Gemini Lake
i2c: mux: pca9541: Export OF device ID table as module aliases
i2c: mux: pca954x: Export OF device ID table as module aliases
i2c: mux: mlxcpld: remove unused including <linux/version.h>
i2c: busses: constify i2c_algorithm structures
i2c: i2c-mux-gpio: rename i2c-gpio-mux to i2c-mux-gpio
i2c: sh_mobile: document support for r8a7796 (R-Car M3-W)
i2c: i2c-cros-ec-tunnel: Reduce logging noise
...
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
- fix for font color when console is switched to another fb driver
- deferred probing fixes for simplefb driver
- preparations to add support of an optional GPIO to enable panel for
ARM CLCD driver
- some improvements for ssd1307fb driver
- cleanups for OMAP fbdev LCD drivers
- misc fixes/cleanups for various fb drivers
* tag 'fbdev-v4.11' of git://github.com/bzolnier/linux: (30 commits)
video: fbdev: fsl-diu-fb: fix spelling mistake "palette"
fbdev: ssd1307fb: include linux/gpio/consumer.h
video: fbdev: fsl-diu-fb: remove impossible condition
video: fbdev: amifb: remove impossible condition
fbdev/ssd1307fb: clear screen in probe
fbdev/ssd1307fb: add support to enable VBAT
fbdev: ssd1307fb: Make reset gpio devicetree property optional
fbdev: ssd1307fb: Remove reset-active-low from the DT binding document
fbdev: ssd1307fb: Start to use gpiod API for reset gpio
video: fbdev: sh_mobile_lcdcfb: fix error return code in sh_mobile_lcdc_probe()
video: fbdev: offb: switch to using for_each_node_by_type
video/console: use setup_timer and mod_timer instead of init_timer
fbdev: omap/lcd: Make callbacks optional
fbdev: omap/lcd: Staticize non-exported lcd_panel structs
fbdev: omap/lcd: Remove no-op driver callbacks
video/mbx: use simple_open()
video: fbdev: stifb: handle NULL return value from ioremap_nocache
video: fbdev: pmagb-b-fb: Remove bad `__init' annotation
video: fbdev: pmag-ba-fb: Remove bad `__init' annotation
video: ARM CLCD: use panel device node for getting backlight and mode
...
These are the current source files that should not have
executable attributes set.
[ Normally this would be sent through Andrew Morton's tree
but his quilt tools don't like permission only patches. ]
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge more updates from Andrew Morton:
- almost all of the rest of MM
- misc bits
- KASAN updates
- procfs
- lib/ updates
- checkpatch updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (124 commits)
checkpatch: remove false unbalanced braces warning
checkpatch: notice unbalanced else braces in a patch
checkpatch: add another old address for the FSF
checkpatch: update $logFunctions
checkpatch: warn on logging continuations
checkpatch: warn on embedded function names
lib/lz4: remove back-compat wrappers
fs/pstore: fs/squashfs: change usage of LZ4 to work with new LZ4 version
crypto: change LZ4 modules to work with new LZ4 module version
lib/decompress_unlz4: change module to work with new LZ4 module version
lib: update LZ4 compressor module
lib/test_sort.c: make it explicitly non-modular
lib: add CONFIG_TEST_SORT to enable self-test of sort()
rbtree: use designated initializers
linux/kernel.h: fix DIV_ROUND_CLOSEST to support negative divisors
lib/find_bit.c: micro-optimise find_next_*_bit
lib: add module support to atomic64 tests
lib: add module support to glob tests
lib: add module support to crc32 tests
kernel/ksysfs.c: add __ro_after_init to bin_attribute structure
...
The idea is that without doing more calculations we extend zero pages to
same element pages for zram. zero page is special case of same element
page with zero element.
1. the test is done under android 7.0
2. startup too many applications circularly
3. sample the zero pages, same pages (none-zero element)
and total pages in function page_zero_filled
the result is listed as below:
ZERO SAME TOTAL
36214 17842 598196
ZERO/TOTAL SAME/TOTAL (ZERO+SAME)/TOTAL ZERO/SAME
AVERAGE 0.060631909 0.024990816 0.085622726 2.663825038
STDEV 0.00674612 0.005887625 0.009707034 2.115881328
MAX 0.069698422 0.030046087 0.094975336 7.56043956
MIN 0.03959586 0.007332205 0.056055193 1.928985507
from the above data, the benefit is about 2.5% and up to 3% of total
swapout pages.
The defect of the patch is that when we recovery a page from non-zero
element the operations are low efficient for partial read.
This patch extends zero_page to same_page so if there is any user to
have monitored zero_pages, he will be surprised if the number is
increased but it's not harmful, I believe.
[minchan@kernel.org: do not free same element pages in zram_meta_free]
Link: http://lkml.kernel.org/r/20170207065741.GA2567@bbox
Link: http://lkml.kernel.org/r/1483692145-75357-1-git-send-email-zhouxianrong@huawei.com
Link: http://lkml.kernel.org/r/1486307804-27903-1-git-send-email-minchan@kernel.org
Signed-off-by: zhouxianrong <zhouxianrong@huawei.com>
Signed-off-by: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If madvise(2) advice will result in the underlying vma being split and
the number of areas mapped by the process will exceed
/proc/sys/vm/max_map_count as a result, return ENOMEM instead of EAGAIN.
EAGAIN is returned by madvise(2) when a kernel resource, such as slab,
is temporarily unavailable. It indicates that userspace should retry
the advice in the near future. This is important for advice such as
MADV_DONTNEED which is often used by malloc implementations to free
memory back to the system: we really do want to free memory back when
madvise(2) returns EAGAIN because slab allocations (for vmas, anon_vmas,
or mempolicies) cannot be allocated.
Encountering /proc/sys/vm/max_map_count is not a temporary failure,
however, so return ENOMEM to indicate this is a more serious issue. A
followup patch to the man page will specify this behavior.
Link: http://lkml.kernel.org/r/alpine.DEB.2.10.1701241431120.42507@chino.kir.corp.google.com
Signed-off-by: David Rientjes <rientjes@google.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: Anshuman Khandual <khandual@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some architectures have a set of zero pages (coloured zero pages)
instead of only one zero page, in order to improve the cache
performance. In those cases, the kernel samepage merger (KSM) would
merge all the allocated pages that happen to be filled with zeroes to
the same deduplicated page, thus losing all the advantages of coloured
zero pages.
This behaviour is noticeable when a process accesses large arrays of
allocated pages containing zeroes. A test I conducted on s390 shows
that there is a speed penalty when KSM merges such pages, compared to
not merging them or using actual zero pages from the start without
breaking the COW.
This patch fixes this behaviour. When coloured zero pages are present,
the checksum of a zero page is calculated during initialisation, and
compared with the checksum of the current canditate during merging. In
case of a match, the normal merging routine is used to merge the page
with the correct coloured zero page, which ensures the candidate page is
checked to be equal to the target zero page.
A sysfs entry is also added to toggle this behaviour, since it can
potentially introduce performance regressions, especially on
architectures without coloured zero pages. The default value is
disabled, for backwards compatibility.
With this patch, the performance with KSM is the same as with non
COW-broken actual zero pages, which is also the same as without KSM.
[akpm@linux-foundation.org: make zero_checksum and ksm_use_zero_pages __read_mostly, per Andrea]
[imbrenda@linux.vnet.ibm.com: documentation for coloured zero pages deduplication]
Link: http://lkml.kernel.org/r/1484927522-1964-1-git-send-email-imbrenda@linux.vnet.ibm.com
Link: http://lkml.kernel.org/r/1484850953-23941-1-git-send-email-imbrenda@linux.vnet.ibm.com
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull sparc updates from David Miller:
1) Support multiple huge page sizes, from Nitin Gupta.
2) Improve boot time on large memory configurations, from Pavel
Tatashin.
3) Make BRK handling more consistent and documented, from Vijay Kumar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Fix build error in flush_tsb_user_page
sparc64: memblock resizes are not handled properly
sparc64: use latency groups to improve add_node_ranges speed
sparc64: Add 64K page size support
sparc64: Multi-page size support
Documentation/sparc: Steps for sending break on sunhv console
sparc64: Send break twice from console to return to boot prom
sparc64: Migrate hvcons irq to panicked cpu
sparc64: Set cpu state to offline when stopped
sunvdc: Add support for setting physical sector size
sparc64: fix for user probes in high memory
sparc: topology_64.h: Fix condition for including cpudata.h
sparc32: mm: srmmu: add __ro_after_init to sparc32_cachetlb_ops structures
Pull md updates from Shaohua Li:
"Mainly fixes bugs and improves performance:
- Improve scalability for raid1 from Coly
- Improve raid5-cache read performance, disk efficiency and IO
pattern from Song and me
- Fix a race condition of disk hotplug for linear from Coly
- A few cleanup patches from Ming and Byungchul
- Fix a memory leak from Neil
- Fix WRITE SAME IO failure from me
- Add doc for raid5-cache from me"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md: (23 commits)
md/raid1: fix write behind issues introduced by bio_clone_bioset_partial
md/raid1: handle flush request correctly
md/linear: shutup lockdep warnning
md/raid1: fix a use-after-free bug
RAID1: avoid unnecessary spin locks in I/O barrier code
RAID1: a new I/O barrier implementation to remove resync window
md/raid5: Don't reinvent the wheel but use existing llist API
md: fast clone bio in bio_clone_mddev()
md: remove unnecessary check on mddev
md/raid1: use bio_clone_bioset_partial() in case of write behind
md: fail if mddev->bio_set can't be created
block: introduce bio_clone_bioset_partial()
md: disable WRITE SAME if it fails in underlayer disks
md/raid5-cache: exclude reclaiming stripes in reclaim check
md/raid5-cache: stripe reclaim only counts valid stripes
MD: add doc for raid5-cache
Documentation: move MD related doc into a separate dir
md: ensure md devices are freed before module is unloaded.
md/r5cache: improve journal device efficiency
md/r5cache: enable chunk_aligned_read with write back cache
...
In soft (no-reboot) mode, the driver self-pings watchdog upon expiration
of an interrupt. However the interrupt itself was not cleared thus on
first hit, the system enters infinite interrupt handling loop.
On Odroid U3 (Exynos4412), when booted with s3c2410_wdt.soft_noboot=1
argument the console is flooded:
# killall -9 watchdog
[ 60.523760] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
[ 60.536744] s3c2410-wdt 10060000.watchdog: watchdog timer expired (irq)
Fix this by writing something to the WTCLRINT register to clear the
interrupt. The register WTCLRINT however appeared in S3C6410 so a new
watchdog quirk and flavor are needed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Many watchdog drivers explicitly stop the watchdog when unregistering it.
While it is unclear if this is actually needed (the whatdog should not be
running at that time if it can be stopped), introduce a helper to
explicitly stop the watchdog in the watchdog core when unregistering it.
This helps reducing driver code size while retaining functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Pull drm updates from Dave Airlie:
"This is the main drm pull request for v4.11.
Nothing too major, the tinydrm and mmu-less support should make
writing smaller drivers easier for some of the simpler platforms, and
there are a bunch of documentation updates.
Intel grew displayport MST audio support which is hopefully useful to
people, and FBC is on by default for GEN9+ (so people know where to
look for regressions). AMDGPU has a lot of fixes that would like new
firmware files installed for some GPUs.
Other than that it's pretty scattered all over.
I may have a follow up pull request as I know BenH has a bunch of AST
rework and fixes and I'd like to get those in once they've been tested
by AST, and I've got at least one pull request I'm just trying to get
the author to fix up.
Core:
- drm_mm reworked
- Connector list locking and iterators
- Documentation updates
- Format handling rework
- MMU-less support for fbdev helpers
- drm_crtc_from_index helper
- Core CRC API
- Remove drm_framebuffer_unregister_private
- Debugfs cleanup
- EDID/Infoframe fixes
- Release callback
- Tinydrm support (smaller drivers for simple hw)
panel:
- Add support for some new simple panels
i915:
- FBC by default for gen9+
- Shared dpll cleanups and docs
- GEN8 powerdomain cleanup
- DMC support on GLK
- DP MST audio support
- HuC loading support
- GVT init ordering fixes
- GVT IOMMU workaround fix
amdgpu/radeon:
- Power/clockgating improvements
- Preliminary SR-IOV support
- TTM buffer priority and eviction fixes
- SI DPM quirks removed due to firmware fixes
- Powerplay improvements
- VCE/UVD powergating fixes
- Cleanup SI GFX code to match CI/VI
- Support for > 2 displays on 3/5 crtc asics
- SI headless fixes
nouveau:
- Rework securre boot code in prep for GP10x secure boot
- Channel recovery improvements
- Initial power budget code
- MMU rework preperation
vmwgfx:
- Bunch of fixes and cleanups
exynos:
- Runtime PM support for MIC driver
- Cleanups to use atomic helpers
- UHD Support for TM2/TM2E boards
- Trigger mode fix for Rinato board
etnaviv:
- Shader performance fix
- Command stream validator fixes
- Command buffer suballocator
rockchip:
- CDN DisplayPort support
- IOMMU support for arm64 platform
imx-drm:
- Fix i.MX5 TV encoder probing
- Remove lower fb size limits
msm:
- Support for HW cursor on MDP5 devices
- DSI encoder cleanup
- GPU DT bindings cleanup
sti:
- stih410 cleanups
- Create fbdev at binding
- HQVDP fixes
- Remove stih416 chip functionality
- DVI/HDMI mode selection fixes
- FPS statistic reporting
omapdrm:
- IRQ code cleanup
dwi-hdmi bridge:
- Cleanups and fixes
adv-bridge:
- Updates for nexus
sii8520 bridge:
- Add interlace mode support
- Rework HDMI and lots of fixes
qxl:
- probing/teardown cleanups
ZTE drm:
- HDMI audio via SPDIF interface
- Video Layer overlay plane support
- Add TV encoder output device
atmel-hlcdc:
- Rework fbdev creation logic
tegra:
- OF node fix
fsl-dcu:
- Minor fixes
mali-dp:
- Assorted fixes
sunxi:
- Minor fix"
[ This was the "fixed" pull, that still had build warnings due to people
not even having build tested the result. I'm not a happy camper
I've fixed the things I noticed up in this merge. - Linus ]
* tag 'drm-for-v4.11-less-shouty' of git://people.freedesktop.org/~airlied/linux: (1177 commits)
lib/Kconfig: make PRIME_NUMBERS not user selectable
drm/tinydrm: helpers: Properly fix backlight dependency
drm/tinydrm: mipi-dbi: Fix field width specifier warning
drm/tinydrm: mipi-dbi: Silence: ‘cmd’ may be used uninitialized
drm/sti: fix build warnings in sti_drv.c and sti_vtg.c files
drm/amd/powerplay: fix PSI feature on Polars12
drm/amdgpu: refuse to reserve io mem for split VRAM buffers
drm/ttm: fix use-after-free races in vm fault handling
drm/tinydrm: Add support for Multi-Inno MI0283QT display
dt-bindings: Add Multi-Inno MI0283QT binding
dt-bindings: display/panel: Add common rotation property
of: Add vendor prefix for Multi-Inno
drm/tinydrm: Add MIPI DBI support
drm/tinydrm: Add helper functions
drm: Add DRM support for tiny LCD displays
drm/amd/amdgpu: post card if there is real hw resetting performed
drm/nouveau/tmr: provide backtrace when a timeout is hit
drm/nouveau/pci/g92: Fix rearm
drm/nouveau/drm/therm/fan: add a fallback if no fan control is specified in the vbios
drm/nouveau/hwmon: expose power_max and power_crit
..
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs.
A handful of driver changes this time around. The larger changes are:
- Reset drivers for hi3660 and zx2967
- AHCI driver for Davinci, acked by Tejun and brought in here due to
platform dependencies
- Cleanups of atmel-ebi (External Bus Interface)
- Tweaks for Rockchip GRF (General Register File) usage (kitchensink
misc register range on the SoCs)
- PM domains changes for support of two new ZTE SoCs (zx296718 and
zx2967)"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (53 commits)
soc: samsung: pmu: Add register defines for pad retention control
reset: make zx2967 explicitly non-modular
reset: core: fix reset_control_put
soc: samsung: pm_domains: Read domain name from the new label property
soc: samsung: pm_domains: Remove message about failed memory allocation
soc: samsung: pm_domains: Remove unused name field
soc: samsung: pm_domains: Use full names in subdomains registration log
sata: ahci-da850: un-hardcode the MPY bits
sata: ahci-da850: add a workaround for controller instability
sata: ahci: export ahci_do_hardreset() locally
sata: ahci-da850: implement a workaround for the softreset quirk
sata: ahci-da850: add device tree match table
sata: ahci-da850: get the sata clock using a connection id
soc: samsung: pmu: Remove duplicated define for ARM_L2_OPTION register
memory: atmel-ebi: Enable the SMC clock if specified
soc: samsung: pmu: Remove unused and duplicated defines
memory: atmel-ebi: Properly handle multiple reference to the same CS
memory: atmel-ebi: Fix the test to enable generic SMC logic
soc: samsung: pm_domains: Add new Exynos5433 compatible
soc: samsung: pmu: Add dummy support for Exynos5433 SoC
...
Pull ARM 64-bit DT updates from Arnd Bergmann:
"ARM64 DT updates are fairly small this time, only two new SoCs and a
handful of new machines get added, all of them similar to other
hardware we already support.
New SoC:
- HiSilicon Kirin960/Hi3660 and HiKey960 development board
- NXP LS1012a with three reference boards:
http://www.nxp.com/products/microcontrollers-and-processors/arm-processors/qoriq-layerscape-arm-processors/qoriq-layerscape-1012a-low-power-communication-processor:LS1012A
New development board:
- Banana Pi M64, based on Allwinner A64:
http://www.banana-pi.org/m64.html
- SolidRun MACCHIATOBin based on Marvell Armada 8K:
https://www.solid-run.com/marvell-armada-family/armada-8040-community-board/
- Broadcom BCM958712DxXMC NorthStar2 reference board (another one)
A lot of platforms improve support for existing machines by adding
extra devices for which a binding and driver is availabe:
Allwinner:
- MMC, USB
ARM Juno:
- Coresight, STM
Broadcom:
- NS2 GICv2m irqchip and PCIe
Marvell:
- Armada 3700 SPI, I2C, ethernet switch
Mediatek:
- MT8173 thermal
NXP i.MX:
- LS1046A thermal
Qualcomm:
- coresight on MSM8916, HDMI, WCNSS, SCM
Renesas:
- r8a779[56] thermal, powerdomain, ethernet, sound, pwm, can, can fd
Rockchip:
- thermal, eDP, pinctrl enhancements
Samsung:
- TM2 touchkey, Exynos5433 HDMI and power management improvements
UniPhier:
- SD reset, eMMC controller
ZTE:
- oppv2 cpufreq"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (110 commits)
arm64: dts: qcom: Add msm8916 CoreSight components
arm64: dts: marvell: adjust name of sd-mmc-gop clock in syscon
arm64: allwinner: add BananaPi-M64 support
arm64: allwinner: a64: add UART1 pin nodes
arm64: allwinner: pine64: add MMC support
arm64: allwinner: a64: Increase the MMC max frequency
arm64: allwinner: a64: Add MMC pinctrl nodes
arm64: allwinner: a64: Add MMC nodes
dt-bindings: clockgen: Add compatible string for LS1012A
Documentation: DT: add LS1012A compatible for SCFG and DCFG
Documentation: DT: Add entry for FSL LS1012A RDB, FRDM, QDS boards
arm64: dts: marvell: add generic-ahci compatibles for CP110 ahci
arm64: tegra: Use symbolic reset identifiers
arm64: dts: r8a7796: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: Mark EthernetAVB device node disabled
arm64: dts: r8a7795: tidyup audma definition order
arm64: dts: r8a7796: Link ARM GIC to clock and clock domain
arm64: dts: r8a7795: Link ARM GIC to clock and clock domain
arm64: dts: r8a7796: Add R-Car Gen3 thermal support
arm64: dts: r8a7795: Add R-Car Gen3 thermal support
...
Pull ARM DT updates from Arnd Bergmann:
"A total of 380 patches this time, mostly adding support for more
hardware in the device tree descriptions. There is not much exciting
here for 4.11, but I've tried my best to condense the information from
the pull requests I got into a readable summary.
Noteworthy changes to existing platforms include:
- The GIC memory map was a bit wrong almost everywhere and now gets
fixed up
- The Allwinner platforms convert to the generic pinmux properties
- The Marvell EBU platforms now use the new DSA binding
- Samsung Exynos4212 was unused and gets removed
- The Renesas power management got improved
New production machines:
- Lego Mindstorms EV3:
https://www.lego.com/en-us/mindstorms/about-ev3
- Beelink X2 Android media box:
http://linux-sunxi.org/Beelink_X2
- "Romulus" baseboard management controller for OpenPower
- Axentia TSE-850 Data Radio Channel (DARC) encoder:
http://www.axentia.se/db/equipment.html
- Luxul XAP-1410 and XWR-1200 wireless access points:
https://luxul.com/xap-1410
New SoCs:
- Allwinner H2+ and V3s, both minor variations of already supported
chips:
http://www.allwinnertech.com/index.php?c=product&a=index&id=38
- Marvell Prestera DX packet processors based on Armada XP
architecture:
http://www.marvell.com/switching/prestera-dx/
- Samsung Exynos4412 Prime gets added, a minor variation of
Exynos4412
New developer and reference boards:
- Lichee Pi One, Lichee Pi Zero and Orange Pi Zero, all based on
Allwinner SoCs:
http://linux-sunxi.org/LicheePi_One
http://www.orangepi.org/orangepizero/
- SAMA5d36ek Reference platform:
http://www.atmel.com/tools/sama5d36-ek.aspx
- Beaglebone Green Wireless and Black Wireless:
https://beagleboard.org/black-wireless
https://beagleboard.org/green-wireless
- phyCORE-AM335x System on Module:
http://phytec.com/products/system-on-modules/phycore/am335x/
- New revision of "vf610-zii" Zodiac Inflight Innovations board
- Various i.MX System-on-Module: Is.IoT MX6UL, SavageBoard, Engicam
i.Core:
http://www.opossom.com/english/index.html
http://www.savageboard.org/
http://www.engicam.com/en/products/embedded/som/sodimm/is-iot-mx6ul
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q
- Liebherr (LWN) monitor 6 based on i.MX6 Quad, no idea what this is
- Cleanups and bugfixes on at91, bcm53xx, i.MX, mvebu, omap, oxnas,
qcom, rockchip, sti, stm32 and tegra
New device supports added to some boards and SoCs, briefly by platform:
- Allwinner: SPDIF, A33 cpufreq, A33 Mali GPU
- Aspeed: network, ipmi bt, gpio, pinmux
- Broadcom: video encoder for raspberry pi, qspi, ethernet, sd/mmc
- TI DaVinci: gpio, lcdc, usb, video-in, uart
- TI Keystone 2: MSM RAM, power/reset, uart
- Mediatek MT2701: clocks, iommu, spi, nand, adc, thermal
- Marvell EBU: ethernet switch on Turris Omnia
- NXP i.MX: otp ram, USB, wifi, bluetooth, spdif, spi, pmic, eeprom,
mmc, nand
- TI OMAP:
- Qualcomm: coresight, gyro/accelerometer, hdmi
- Renesas: pmic, soc-id
- Rockchip: qos
- Samsung: audio on Odroid-X
- Socfpga: FPGA manager, i2c, led, can, watchdog, nand, power monitor
- STi: video in/out
- STM32: timer, pwm, i2c, rtc, add, i2s
- NVIDIA Tegra: tpm
- Uniphier: mmc/sd pinmux"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (380 commits)
ARM: dts: armada-385-linksys: fix DSA compatible property
ARM: dts: Fix typo in armada-xp-98dx4251
ARM: DTS: Fix register map for virt-capable GIC
dt-bindings: arm,gic: Fix binding example for a virt-capable GIC
ARM: dts: sun8i: sinlinx: Enable audio nodes
ARM: dts: sun8i: parrot: Enable audio nodes
ARM: dts: sun8i: Add audio codec, dai and card for A33
ARM: dts: Add EMAC AXI settings for Arria10
ARM: dts: am335x-chiliboard: Support charger
ARM: dts: am335x-chiliboard: Support power button
ARM: sun8i: dt: Add mali node
dt-bindings: gpu: Add Mali Utgard bindings
ARM: dts: stm32: Add I2C1 support for STM32429 eval board
ARM: dts: stm32: Add I2C1 support for STM32F429 SoC
ARM: dts: stm32: Use clock DT binding definition on stm32f429 family
dt-bindings: mfd: stm32f4: Add missing binding definition
dt-bindings: mfd: stm32f4: Fix STM32F4_X_CLOCK() macro
ARM: dts: stm32: Enable pwm1 and pwm3 for stm32f469-disco
ARM: dts: stm32: add Timers driver for stm32f429 MCU
ARM: dts: add the AB8500 sysclk to the device trees
...
Pull ARM SoC platform updates from Arnd Bergmann:
"In the SoC branch we normally collect classic arch/arm/mach-*
contents, i.e. C code changes for SoC platforms. This release cycle
the diffstat is quite nice, in that we're removing 3x the amount of
code that's being added.
The main reason for this is that there's a removal of camera drivers
for Freescale i.MX chips (driver was removed so the device
registration isn't needed any more). There's also removal of display
initialization code for OMAP that is no longer needed.
The rest are mostly minor tweaks and cleanups; constification on
Samsung platforms, cleanup of ux500 platform data, purge of other
unused platform data/device seutp on i.MX and other good stuff.
New SoC support this cycle is for two Allwinner platforms, H2+ and
V3s"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (55 commits)
ARM: ux500: remove deleted file from Makefile
ARM: ep93xx: Disable TS-72xx watchdog before uncompressing
ARM: ux500: cut some platform data
MAINTAINERS: Update for the current location of the bcm2835 tree.
ARM: davinci: remove BUG_ON() from da850_register_sata()
ARM: davinci: da850: model the SATA refclk
ARM: davinci: da850: add con_id for the SATA clock
ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for SATA
arm: mvebu: support for SMP on 98DX3336 SoC
dt-bindings: video: exynos7-decon: Remove obsolete samsung,power-domain property
soc: dove: constify reset_control_ops structures
ARM: mv78xx0: fix possible PCI buffer overflow
MAINTAINERS: transfer maintainership for the EZX platform
ARM: shmobile: rcar-gen2: Add more register documentation
ARM: tegra: paz00: Fix __initdata placement
ARM: OMAP: clock: Remove unused mpurate cmdline option
ARM: davinci: add skeleton for pdata-quirks
arm: sunxi: add support for V3s SoC
ARM: OMAP2+: omap_hwmod: Add support for earlycon
arm: hisi: drop extern hip01_cpu_die
...
drm/panel: Changes for v4.11-rc1
This set contains a couple of cleanups as well as support for a few more
simple panels.
* tag 'drm/panel/for-4.11-rc1' of git://anongit.freedesktop.org/tegra/linux:
drm/panel: simple: Specify bus width and flags for EDT displays
drm/panel: simple: Add Netron DY E231732
of: Add vendor prefix for Netron DY
drm/panel: simple: Add support for Tianma TM070JDHG30
of: Add vendor prefix for Tianma Micro-electronics
drm/panel: simple: Add support BOE NV101WXMN51
dt-bindings: display: Add BOE NV101WXMN51 panel binding
drm/panel: Constify device node argument to of_drm_find_panel()
Pull PCI updates from Bjorn Helgaas:
- add ASPM L1 substate support
- enable PCIe Extended Tags when supported
- configure PCIe MPS settings on iProc, Versatile, X-Gene, and Xilinx
- increase VPD access timeout
- add ACS quirks for Intel Union Point, Qualcomm QDF2400 and QDF2432
- use new pci_irq_alloc_vectors() in more drivers
- fix MSI affinity memory leak
- remove unused MSI interfaces and update documentation
- remove unused AER .link_reset() callback
- avoid pci_lock / p->pi_lock deadlock seen with perf
- serialize sysfs enable/disable num_vfs operations
- move DesignWare IP from drivers/pci/host/ to drivers/pci/dwc/ and
refactor so we can support both hosts and endpoints
- add DT ECAM-like support for HiSilicon Hip06/Hip07 controllers
- add Rockchip system power management support
- add Thunder-X cn81xx and cn83xx support
- add Exynos 5440 PCIe PHY support
* tag 'pci-v4.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (93 commits)
PCI: dwc: Remove dependency of designware on CONFIG_PCI
PCI: dwc: Add CONFIG_PCIE_DW_HOST to enable PCI dwc host
PCI: dwc: Split pcie-designware.c into host and core files
PCI: dwc: designware: Fix style errors in pcie-designware.c
PCI: dwc: designware: Parse "num-lanes" property in dw_pcie_setup_rc()
PCI: dwc: all: Split struct pcie_port into host-only and core structures
PCI: dwc: designware: Get device pointer at the start of dw_pcie_host_init()
PCI: dwc: all: Rename cfg_read/cfg_write to read/write
PCI: dwc: all: Use platform_set_drvdata() to save private data
PCI: dwc: designware: Move register defines to designware header file
PCI: dwc: Use PTR_ERR_OR_ZERO to simplify code
PCI: dra7xx: Group PHY API invocations
PCI: dra7xx: Enable MSI and legacy interrupts simultaneously
PCI: dra7xx: Add support to force RC to work in GEN1 mode
PCI: dra7xx: Simplify probe code with devm_gpiod_get_optional()
PCI: Move DesignWare IP support to new drivers/pci/dwc/ directory
PCI: exynos: Support the PHY generic framework
Documentation: binding: Modify the exynos5440 PCIe binding
phy: phy-exynos-pcie: Add support for Exynos PCIe PHY
Documentation: samsung-phy: Add exynos-pcie-phy binding
...
Pull rpmsg updates from Bjorn Andersson:
"This introduces an interface for user space to directly communicate on
rpmsg endpoints without the implementation of specific kernel drivers,
which is useful for e.g. debug channels:
* tag 'rpmsg-v4.11' of git://github.com/andersson/remoteproc:
rpmsg: rpmsg_create_ept() returns NULL on error
rpmsg: qcom: smd: Return positively when not enabled
rpmsg: unlock on error in rpmsg_eptdev_read()
rpmsg: char: add CONFIG_NET dependency
rpmsg: smd: Register rpmsg user space interface for edges
rpmsg: Driver for user space endpoint interface
rpmsg: qcom_smd: Implement endpoint "poll"
rpmsg: Introduce "poll" to endpoint ops
rpmsg: qcom_smd: Add support for "label" property
Pull remoteproc updates from Bjorn Andersson:
"This introduces support for booting the dedicated sensor core in the
Qualcomm MSM8996, updates the Qualcomm ADSP and Hexagon drivers to
utilize SMD subdevice helpers for properly handle shutdowns and
restarts of the remoteproc, add virtio support to the ST remoteproc
and refactor the Qualcomm Hexagon driver to handle variations between
platforms.
The support code for parsing, loading and authenticating Qualcomm
firmware files (MDT) is refactored and move to drivers/soc/qcom, to
allow for non-remoteproc drivers to utilize this.
Finally it brings some cleanups to the remoteproc core"
* tag 'rproc-v4.11' of git://github.com/andersson/remoteproc: (27 commits)
remoteproc: qcom: mdt_loader: Use signed type for offset
remoteproc: st: add virtio communication support
remoteproc: st: correct probe error management
remoteproc: Modify the function names
remoteproc: Reduce asynchronous request_firmware to auto-boot only
remoteproc: Drop qcom_scm_pas_supported() from adsp_probe()
MAINTAINERS: Add missing rpmsg include path
remoteproc: qcom: Use common SMD edge handler
remoteproc: qcom: wcnss: Make SMD handling common
remoteproc: Move qcom_mdt_loader into drivers/soc/qcom
remoteproc: qcom: mdt_loader: Refactor MDT loader
remoteproc: qcom: mdt_loader: Don't overwrite firmware object
remoteproc: qcom: Extract non-mdt related helper
remoteproc: qcom: q6v5: Decouple driver from MDT loader
remoteproc: qcom: q6v5: Remove mss supply from 8916
remoteproc: qcom: fix initializers for qcom_mss_reg_res array
remoteproc: Drop firmware_loading_complete
remoteproc: Add RPROC_DELETED state
remoteproc: Move rproc_delete_debug_dir() to rproc_del()
remoteproc: qcom: Add SLPI rproc support to load and boot slpi proc.
...
Pull sound updates from Takashi Iwai:
"Here is the update of sound bits for 4.11: again at this time, no big
changes in ALSA and ASoC core but only cosmetic changes like
consitifaction.
Meanwhile, quite a lot of developments are seen in a few driver side.
ALSA Core:
- Clean up, consitification of some ops
HD-audio:
- A slight behavior change of single_cmd option
- Quirks for AmigaOne X1000, Samsung Ativ Book 8, Dell AiO, ALC221
HP, and fixes for Lewisburg controller
- Realtek ALC299, ALC1220 codecs
Others:
- USB-audio: Tascam US-16x08 DSP mixer quirk
- Intel HDMI LPE audio support for Baytrail / Cherrytrail; this
contains some updates in drm/i915 for the new platform binding
ASoC:
- Lots of updates in Intel drivers, mostly for DisplayPort and HDMI
on Skylake and onwards, as well as more Baytrail / Cherrytrail
boards support
- Channel mapping support for HDMI
- Support for AllWinner A31 and A33, Everest Semiconductor ES8328,
Nuvoton NAU8540.
* tag 'sound-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (323 commits)
ALSA: usb-audio: Tidy up mixer_us16x08.c
ALSA: usb-audio: Fix memory leak and corruption in mixer_us16x08.c
ALSA: usb-audio: purge needless variable length array
ALSA: x86: hdmi: select CONFIG_SND_PCM
ALSA: x86: Don't enable runtime PM as default
ALSA: x86: Use runtime PM autosuspend
ALSA: usb-audio: localize function without external linkage
ALSA: usb-audio: localize one-referrer variable
ALSA: usb-audio: Tascam US-16x08 DSP mixer quirk
ALSA: emu10k1: constify snd_emux_operators structure
ASoC: sun4i-spdif: drop unnessary snd_soc_unregister_component()
ASoC: Intel: bxt: Add jack port initialize in bxt_rt298 machine
ASoC: nau8825: automatic BCLK and LRC divde in master mode
ASoC: hdac_hdmi: Add device id for Geminilake
ASoC: Intel: Skylake: Add Geminlake IDs
ASoC: rt298: Add DMI match for Geminilake reference platform
ASoC: Intel: Skylake: Check device type to get endpoint configuration
ASoC: Intel: bxt: Add jack port initialize in da7219_max98357a machine
ASoC: Intel: Skylake: Add jack port initialize in nau88l25_ssm4567 machine
ASoC: Intel: Skylake: Add jack port initialize in nau88l25_max98357a machine
...
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.11 cycle
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do. This is a
treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace ABI
correctly reflect the current in-kernel consumer of a pin taken
using this abstraction. This is a treewide change also updating all
users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide change
also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing a
backend into the pin control subsystem that were also merged into
the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace to fully
test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime PM
support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations"
* tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: reintroduce devm_get_gpiod_from_child()
gpio: pci-idio-16: Fix PCI BAR index
gpio: pci-idio-16: Fix PCI device ID code
gpio: mockup: implement event injecting over debugfs
gpio: mockup: add a dummy irqchip
gpio: mockup: implement naming the lines
gpio: mockup: code shrink
gpio: mockup: readability tweaks
gpio: Add GPIO support for the ACCES PCI-IDIO-16
gpio: Add the devm_fwnode_get_index_gpiod_from_child() helper
gpio: Rename devm_get_gpiod_from_child()
gpio: mcp23s08: Select REGMAP/REGMAP_I2C to fix build error
gpio: ws16c48: Add support for GPIO names
gpio: gpio-mm: Add support for GPIO names
gpio: 104-idio-16: Add support for GPIO names
gpio: 104-idi-48: Add support for GPIO names
gpio: 104-dio-48e: Add support for GPIO names
gpio: ws16c48: Remove unnecessary driver_data set
gpio: gpio-mm: Remove unnecessary driver_data set
gpio: 104-idio-16: Remove unnecessary driver_data set
...
Pull input updates from Dmitry:
- a new driver for Zeitech touchscreen controller
- a new driver for Samsung "touchkeys"
- touchscreen driver for Moorestown platform has been removed because
platform support is gone
- MPU3050 accelerometer driver was removed in favor of IIO driver
- miscellaneous driver cleanup and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (88 commits)
Input: zet6223 - export OF device ID as module aliases
Input: tsc2004/5 - switch to using generic device properties
Input: tsc2004/5 - fix regulator handling
Input: tsc2005 - add OF device table
Input: add driver for Zeitec ZET6223
Input: joydev - do not report stale values on first open
Input: synaptics-rmi4 - forward upper mechanical buttons to PS/2 guest
Input: synaptics-rmi4 - clean up F30 implementation
Input: synaptics - use SERIO_OOB_DATA to handle trackstick buttons
Input: psmouse - add a custom serio protocol to send extra information
Input: synaptics-rmi4 - fix error return code in rmi_probe_interrupts()
Input: xpad - restore LED state after device resume
Input: synaptics-rmi4 - add rmi_find_function()
Input: xpad - fix stuck mode button on Xbox One S pad
Input: joydev - use clamp() macro
Input: refuse to register absolute devices without absinfo
Input: synaptics-rmi4 - add sysfs interfaces for hardware IDs
Input: synaptics-rmi4 - add sysfs attribute update_fw_status
Input: mousedev - stop offering PS/2 to userspace by default
Input: tca8418 - switch to using generic device properties
...
