commit 83810f84ecf11dfc5a9414a8b762c3501b328185 upstream.
If ports are not turned off in shutdown then runtime suspended
self-powered USB devices may survive in U3 link state over S5.
During subsequent boot, if firmware sends an IPC command to program
the port in DISCONNECT state, it will time out, causing significant
delay in the boot time.
Turning off roothub port power is also recommended in xhci
specification 4.19.4 "Port Power" in the additional note.
Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220623111945.1557702-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit dc92944a014cd6a6f6c94299aaa36164dd2c238a upstream.
While rebooting, XHCI controller and its bus device will be shut down
in order by .shutdown callback. Stopping roothubs polling in
xhci_shutdown() can prevent XHCI driver from accessing port status
after its bus device shutdown.
Take PCIe XHCI controller as example, if XHCI driver doesn't stop roothubs
polling, XHCI driver may access PCIe BAR register for port status after
parent PCIe root port driver is shutdown and cause PCIe bus error.
[check shared hcd exist before stopping its roothub polling -Mathias]
Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220408134823.2527272-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 14073ce951b5919da450022c050772902f24f054 upstream.
xhci_reset() timeout was increased from 250ms to 10 seconds in order to
give Renesas 720201 xHC enough time to get ready in probe.
xhci_reset() is called with interrupts disabled in other places, and
waiting for 10 seconds there is not acceptable.
Add a timeout parameter to xhci_reset(), and adjust it back to 250ms
when called from xhci_stop() or xhci_shutdown() where interrupts are
disabled, and successful reset isn't that critical.
This solves issues when deactivating host mode on platforms like SM8450.
For now don't change the timeout if xHC is reset in xhci_resume().
No issues are reported for it, and we need the reset to succeed.
Locking around that reset needs to be revisited later.
Additionally change the signed integer timeout parameter in
xhci_handshake() to a u64 to match the timeout value we pass to
readl_poll_timeout_atomic()
Fixes: 22ceac1912 ("xhci: Increase reset timeout for Renesas 720201 host.")
Cc: stable@vger.kernel.org
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reported-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 243a1dd7ba48c120986dd9e66fee74bcb7751034 upstream.
The -ENODEV return value from xhci_check_args() is incorrectly changed
to -EINVAL in a couple places before propagated further.
xhci_check_args() returns 4 types of value, -ENODEV, -EINVAL, 1 and 0.
xhci_urb_enqueue and xhci_check_streams_endpoint return -EINVAL if
the return value of xhci_check_args <= 0.
This causes problems for example r8152_submit_rx, calling usb_submit_urb
in drivers/net/usb/r8152.c.
r8152_submit_rx will never get -ENODEV after submiting an urb when xHC
is halted because xhci_urb_enqueue returns -EINVAL in the very beginning.
[commit message and header edit -Mathias]
Fixes: 203a86613f ("xhci: Avoid NULL pointer deref when host dies.")
Cc: stable@vger.kernel.org
Signed-off-by: Hongyu Xie <xiehongyu1@kylinos.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220215123320.1253947-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 7faac1953ed1f658f719cdf7bb7303fa5eef822c upstream.
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 811ae81320da53a5670c36970cefacca8519f90e upstream.
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b7a0a792f864583207c593b50fd1b752ed89f4c1 upstream.
Set "HCD_FLAG_DEFER_RH_REGISTER" to hcd->flags in xhci_run() to defer
registering primary roothub in usb_add_hcd(). This will make sure both
primary roothub and secondary roothub will be registered along with the
second HCD. This is required for cold plugged USB devices to be detected
in certain PCIe USB cards (like Inateck USB card connected to AM64 EVM
or J7200 EVM).
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-3-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 2847c46c61486fd8bca9136a6e27177212e78c69 ]
This reverts commit 5d5323a6f3625f101dbfa94ba3ef7706cce38760.
That commit effectively disabled Intel host initiated U1/U2 lpm for devices
with periodic endpoints.
Before that commit we disabled host initiated U1/U2 lpm if the exit latency
was larger than any periodic endpoint service interval, this is according
to xhci spec xhci 1.1 specification section 4.23.5.2
After that commit we incorrectly checked that service interval was smaller
than U1/U2 inactivity timeout. This is not relevant, and can't happen for
Intel hosts as previously set U1/U2 timeout = 105% * service interval.
Patch claimed it solved cases where devices can't be enumerated because of
bandwidth issues. This might be true but it's a side effect of accidentally
turning off lpm.
exit latency calculations have been revised since then
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210820123503.2605901-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit dda32c00c9a0fa103b5d54ef72c477b7aa993679 upstream.
'xhci_urb_enqueue()' is passed a 'mem_flags' argument, because "URBs may be
submitted in interrupt context" (see comment related to 'usb_submit_urb()'
in 'drivers/usb/core/urb.c')
So this flag should be used in all the calling chain.
Up to now, 'xhci_check_maxpacket()' which is only called from
'xhci_urb_enqueue()', uses GFP_KERNEL.
Be safe and pass the mem_flags to this function as well.
Fixes: ddba5cd0ae ("xhci: Use command structures when queuing commands on the command ring")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210512080816.866037-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 286fd02fd54b6acab65809549cf5fb3f2a886696 ]
The Max Interrupters supported by the controller is given in a 10bit
wide bitfield, but the driver uses a fixed 128 size array to index these
interrupters.
Klockwork reports a possible array out of bounds case which in theory
is possible. In practice this hasn't been hit as a common number of Max
Interrupters for new controllers is 8, not even close to 128.
This needs to be fixed anyway
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210406070208.3406266-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit d26c00e7276fc92b18c253d69e872f6b03832bad upstream.
If port terminations are detected in suspend, but link never reaches U0
then xHCI may have an internal uncleared wake state that will cause an
immediate wake after suspend.
This wake state is normally cleared when driver clears the PORT_CSC bit,
which is set after a device is enabled and in U0.
Write 1 to clear PORT_CSC for ports that don't have anything connected
when suspending. This makes sure any pending internal wake states in
xHCI are cleared.
Cc: stable@vger.kernel.org
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 253f588c70f66184b1f3a9bbb428b49bbda73e80 upstream.
A xHC USB 3 port might miss the first wake signal from a USB 3 device
if the port LFPS reveiver isn't enabled fast enough after xHC resume.
xHC host will anyway be resumed by a PME# signal, but will go back to
suspend if no port activity is seen.
The device resends the U3 LFPS wake signal after a 100ms delay, but
by then host is already suspended, starting all over from the
beginning of this issue.
USB 3 specs say U3 wake LFPS signal is sent for max 10ms, then device
needs to delay 100ms before resending the wake.
Don't suspend immediately if port activity isn't detected in resume.
Instead add a retry. If there is no port activity then delay for 120ms,
and re-check for port activity.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20210311115353.2137560-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1d69f9d901ef14d81c3b004e3282b8cc7b456280 upstream.
xhci-mtk needs XHCI_MTK_HOST quirk functions in add_endpoint() and
drop_endpoint() to handle its own sw bandwidth management.
It stores bandwidth data into an internal table every time
add_endpoint() is called, and drops those in drop_endpoint().
But when bandwidth allocation fails at one endpoint, all earlier
allocation from the same interface could still remain at the table.
This patch moves bandwidth management codes to check_bandwidth() and
reset_bandwidth() path. To do so, this patch also adds those functions
to xhci_driver_overrides and lets mtk-xhci to release all failed
endpoints in reset_bandwidth() path.
Fixes: 08e469de87 ("usb: xhci-mtk: supports bandwidth scheduling with multi-TT")
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Link: https://lore.kernel.org/r/20210113180444.v6.1.Id0d31b5f3ddf5e734d2ab11161ac5821921b1e1e@changeid
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5d5323a6f3625f101dbfa94ba3ef7706cce38760 upstream.
The commit 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit
latency is too long") was constraining the xhci code not to allow U1/U2
sleep states if the latency to wake up from the U-states reached the
service interval of an periodic endpoint. This fix was not taking into
account that in case the quirk XHCI_INTEL_HOST is set, the wakeup time
will be calculated and configured differently.
It checks for u1_params.mel/u2_params.mel as a limit. But the code could
decide to write another MEL into the hardware. This leads to broken
cases where not enough bandwidth is available for other devices:
usb 1-2: can't set config #1, error -28
This patch is fixing that case by checking for timeout_ns after the
wakeup time was calculated depending on the quirks.
Fixes: 0472bf06c6 ("xhci: Prevent U1/U2 link pm states if exit latency is too long")
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201215193147.11738-1-m.grzeschik@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Creating debugfs files while loding the spin_lock_irqsave(xhci->lock)
creates a lock dependecy that could possibly deadlock.
Lockdep warns:
=====================================================
WARNING: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected
5.10.0-rc1pdx86+ #8 Not tainted
-----------------------------------------------------
systemd-udevd/386 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
ffffffffb1a94038 (pin_fs_lock){+.+.}-{2:2}, at: simple_pin_fs+0x22/0xa0
and this task is already holding:
ffff9e7b87fbc430 (&xhci->lock){-.-.}-{2:2}, at: xhci_alloc_streams+0x5f9/0x810
which would create a new lock dependency:
(&xhci->lock){-.-.}-{2:2} -> (pin_fs_lock){+.+.}-{2:2}
Create the files a bit later after lock is released.
Fixes: 673d746836 ("usb: xhci: add debugfs support for ep with stream")
CC: Li Jun <jun.li@nxp.com>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20201028203124.375344-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To show the trb ring of streams, use the exsiting ring files of bulk ep
to show trb ring of one specific stream ID, which stream ID's trb ring
will be shown, is controlled by a new debugfs file stream_id, this is to
avoid to create a large number of dir for every allocate stream IDs,
another debugfs file stream_context_array is created to show all the
allocated stream context array entries.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-11-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure xHC completes the configure endpoint command and xhci driver
sets the ring pointers correctly before we create the user readable
debugfs file.
In theory there was a small gap where a user could have read the
debugfs file and cause a NULL pointer dereference error as ring
pointer was not yet set, in practise we want this change to simplify
the upcoming streams debugfs support.
Fixes: 02b6fdc2a1 ("usb: xhci: Add debugfs interface for xHCI driver")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the xhci-plat.c is the platform driver, after the runtime pm is
enabled, the xhci_suspend is called if nothing is connected on
the port. When the system goes to suspend, it will call xhci_suspend again
if USB wakeup is enabled.
Since the runtime suspend wakeup setting is not always the same as
system suspend wakeup setting, eg, at runtime suspend we always need
wakeup if the controller is in low power mode; but at system suspend,
we may not need wakeup. So, we move the judgement after changing
wakeup setting.
[commit message rewording -Mathias]
Reviewed-by: Jun Li <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200918131752.16488-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull USB fixes from Greg KH:
"Let's try this again... Here are some USB fixes for 5.9-rc3.
This differs from the previous pull request for this release in that
the usb gadget patch now does not break some systems, and actually
does what it was intended to do. Many thanks to Marek Szyprowski for
quickly noticing and testing the patch from Andy Shevchenko to resolve
this issue.
Additionally, some more new USB quirks have been added to get some new
devices to work properly based on user reports.
Other than that, the patches are all here, and they contain:
- usb gadget driver fixes
- xhci driver fixes
- typec fixes
- new quirks and ids
- fixes for USB patches that went into 5.9-rc1.
All of these have been tested in linux-next with no reported issues"
* tag 'usb-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: storage: Add unusual_uas entry for Sony PSZ drives
USB: Ignore UAS for JMicron JMS567 ATA/ATAPI Bridge
usb: host: ohci-exynos: Fix error handling in exynos_ohci_probe()
USB: gadget: u_f: Unbreak offset calculation in VLAs
USB: quirks: Ignore duplicate endpoint on Sound Devices MixPre-D
usb: typec: tcpm: Fix Fix source hard reset response for TDA 2.3.1.1 and TDA 2.3.1.2 failures
USB: PHY: JZ4770: Fix static checker warning.
USB: gadget: f_ncm: add bounds checks to ncm_unwrap_ntb()
USB: gadget: u_f: add overflow checks to VLA macros
xhci: Always restore EP_SOFT_CLEAR_TOGGLE even if ep reset failed
xhci: Do warm-reset when both CAS and XDEV_RESUME are set
usb: host: xhci: fix ep context print mismatch in debugfs
usb: uas: Add quirk for PNY Pro Elite
tools: usb: move to tools buildsystem
USB: Fix device driver race
USB: Also match device drivers using the ->match vfunc
usb: host: xhci-tegra: fix tegra_xusb_get_phy()
usb: host: xhci-tegra: otg usb2/usb3 port init
usb: hcd: Fix use after free in usb_hcd_pci_remove()
usb: typec: ucsi: Hold con->lock for the entire duration of ucsi_register_port()
...
Some device drivers call libusb_clear_halt when target ep queue
is not empty. (eg. spice client connected to qemu for usb redir)
Before commit f5249461b5 ("xhci: Clear the host side toggle
manually when endpoint is soft reset"), that works well.
But now, we got the error log:
EP not empty, refuse reset
xhci_endpoint_reset failed and left ep_state's EP_SOFT_CLEAR_TOGGLE
bit still set
So all the subsequent urb sumbits to the ep will fail with the
warn log:
Can't enqueue URB while manually clearing toggle
We need to clear ep_state EP_SOFT_CLEAR_TOGGLE bit after
xhci_endpoint_reset, even if it failed.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: stable <stable@vger.kernel.org> # v4.17+
Signed-off-by: Ding Hui <dinghui@sangfor.com.cn>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200821091549.20556-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB2 devices with LPM enabled may interrupt the system suspend:
[ 932.510475] usb 1-7: usb suspend, wakeup 0
[ 932.510549] hub 1-0:1.0: hub_suspend
[ 932.510581] usb usb1: bus suspend, wakeup 0
[ 932.510590] xhci_hcd 0000:00:14.0: port 9 not suspended
[ 932.510593] xhci_hcd 0000:00:14.0: port 8 not suspended
..
[ 932.520323] xhci_hcd 0000:00:14.0: Port change event, 1-7, id 7, portsc: 0x400e03
..
[ 932.591405] PM: pci_pm_suspend(): hcd_pci_suspend+0x0/0x30 returns -16
[ 932.591414] PM: dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -16
[ 932.591418] PM: Device 0000:00:14.0 failed to suspend async: error -16
During system suspend, USB core will let HC suspends the device if it
doesn't have remote wakeup enabled and doesn't have any children.
However, from the log above we can see that the usb 1-7 doesn't get bus
suspended due to not in U0. After a while the port finished U2 -> U0
transition, interrupts the suspend process.
The observation is that after disabling LPM, port doesn't transit to U0
immediately and can linger in U2. xHCI spec 4.23.5.2 states that the
maximum exit latency for USB2 LPM should be BESL + 10us. The BESL for
the affected device is advertised as 400us, which is still not enough
based on my testing result.
So let's use the maximum permitted latency, 10000, to poll for U0
status to solve the issue.
Cc: stable@vger.kernel.org
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unable to complete the enumeration of a USB TV Tuner device.
Per XHCI spec (4.6.5), the EP state field of the input context shall
be cleared for a set address command. In the special case of an FS
device that has "MaxPacketSize0 = 8", the Linux XHCI driver does
not do this before evaluating the context. With an XHCI controller
that checks the EP state field for parameter context error this
causes a problem in cases such as the device getting reset again
after enumeration.
When that field is cleared, the problem does not occur.
This was found and fixed by Sasi Kumar.
Cc: stable@vger.kernel.org
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200624135949.22611-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a class driver cancels its only URB then the endpoint ring buffer will
appear empty to the xhci driver. xHC hardware may still process cached
TRBs, and complete with a STALL, halting the endpoint.
This halted endpoint was not handled correctly by xhci driver as events on
empty rings were all assumed to be spurious events.
xhci driver refused to restart the ring with EP_HALTED flag set, so class
driver was never informed the endpoint halted even if it queued new URBs.
The host side of the endpoint needs to be reset, and dequeue pointer should
be moved in order to clear the cached TRBs and resetart the endpoint.
Small adjustments in finding the new dequeue pointer are needed to support
the case of stall on an empty ring and unknown current TD.
Cc: <stable@vger.kernel.org>
cc: Jeremy Compostella <jeremy.compostella@intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200421140822.28233-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bail out early if the xHC host needs to be reset at resume
but driver can't access xHC PCI registers.
If xhci driver already fails to reset the controller then there
is no point in attempting to free, re-initialize, re-allocate and
re-start the host. If failure to access the host is detected later,
failing the resume, xhci interrupts will be double freed
when remove is called.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200312144517.1593-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patch "USB: HCD: support giveback of URB in tasklet context"[1]
introduced giveback of urb in tasklet context. [1] This patch was
applied to ehci but not xhci. [2] This patch significantly reduces
the hard irq time of xhci. Especially for uvc driver, the hard irq
including the uvc completion function runs quite long but applying
this patch reduces the hard irq time of xhci.
I have tested four SS devices to check if performance degradation
occurs when urb completion functions run in the tasklet context.
As a result of the test, all devices works well and shows very
similar performance with the upstream kernel. Moreover, usb ethernet
adapter show better performance than the upstream kernel about 5% for
RX and 2% for TX. Four SS devices is as follows.
SS devices for test
1. WD My Passport 2TB (external hard drive)
2. Sandisk Ultra Flair USB 3.0 32GB
3. Logitech Brio webcam
4. Iptime 1gigabit ethernet adapter (Mediatek RTL8153)
Test description
1. Mass storage (hard drive) performance test
- run below command 10 times and compute the average performance
dd if=/dev/sdN iflag=direct of=/dev/null bs=1G count=1
2. Mass storage (flash memory) performance test
- run below command 10 times and compute the average performance
dd if=/dev/sdN iflag=direct of=/dev/null bs=1G count=1
3. Webcam streaming performance test
- run simple capture program and get the average frame rate per second
- capture 1500 frames
- program link
https://github.com/asfaca/Webcam-performance-analyzing-tool
- video resolution : 4096 X 2160 (4K) at 30 or 24 fps
- device (Logitech Brio) spec url for the highest resolution and fps
https://support.logitech.com/en_gb/product/brio-stream/specs
4. USB Ethernet adapter performance test
- directly connect two linux machines with ethernet cable
- run pktgen of linux kernel and send 1500 bytes packets
- run vnstat to measure the network bandwidth for 180 seconds
Test machine
- CPU : Intel i5-7600 @ 3.5GHz
Test results
1. Mass storage (hard drive) performance test
WD My Passport 2TB (external hard drive)
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
103.667MB/s | 103.692MB/s
--------------------------------------------------------------------
2. Mass storage (flash memory) performance test
Sandisk Ultra Flair USB 3.0 32GB
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
129.727MB/s | 130.2MB/s
--------------------------------------------------------------------
3. Webcam streaming performance test
Logitech Brio webcam
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
26.4451 fps | 26.3949 fps
--------------------------------------------------------------------
4. USB Ethernet adapter performance test
Iptime 1gigabit ethernet adapter (Mediatek RTL8153)
--------------------------------------------------------------------
xhci without tasklet | xhci with tasklet
--------------------------------------------------------------------
RX 933.86 Mbit/s | 983.86 Mbit/s
--------------------------------------------------------------------
TX 830.18 Mbit/s | 882.75 Mbit/s
--------------------------------------------------------------------
[1], https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=94dfd7edfd5c9b605caf7b562de7a813d216e011
[2], https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=428aac8a81058e2303677a8fbf26670229e51d3a
Signed-off-by: Suwan Kim <suwan.kim027@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1573836603-10871-4-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer") schedules work
to clear TT buffer, but causes a use-after-free regression at the same time
Make sure hub_tt_work finishes before endpoint is disabled, otherwise
the work will dereference already freed endpoint and device related
pointers.
This was triggered when usb core failed to read the configuration
descriptor of a FS/LS device during enumeration.
xhci driver queued clear_tt_work while usb core freed and reallocated
a new device for the next enumeration attempt.
EHCI driver implents ehci_endpoint_disable() that makes sure
clear_tt_work has finished before it returns, but xhci lacks this support.
usb core will call hcd->driver->endpoint_disable() callback before
disabling endpoints, so we want this in xhci as well.
The added xhci_endpoint_disable() is based on ehci_endpoint_disable()
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Cc: <stable@vger.kernel.org> # v5.3
Reported-by: Johan Hovold <johan@kernel.org>
Suggested-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Johan Hovold <johan@kernel.org>
Tested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-2-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The system can hit a deadlock if an xhci adapter breaks while initializing.
The deadlock is between two threads: thread 1 is tearing down the
adapter and is stuck in usb_unlocked_disable_lpm waiting to lock the
hcd->handwidth_mutex. Thread 2 is holding this mutex (while still trying
to add a usb device), but is stuck in xhci_endpoint_reset waiting for a
stop or config command to complete. A reboot is required to resolve.
It turns out when calling xhci_queue_stop_endpoint and
xhci_queue_configure_endpoint in xhci_endpoint_reset, the return code is
not checked for errors. If the timing is right and the adapter dies just
before either of these commands get issued, we hang indefinitely waiting
for a completion on a command that didn't get issued.
This wasn't a problem before the following fix because we didn't send
commands in xhci_endpoint_reset:
commit f5249461b5 ("xhci: Clear the host side toggle manually when
endpoint is soft reset")
With the patch I am submitting, a duration test which breaks adapters
during initialization (and which deadlocks with the standard kernel) runs
without issue.
Fixes: f5249461b5 ("xhci: Clear the host side toggle manually when endpoint is soft reset")
Cc: <stable@vger.kernel.org> # v4.17+
Cc: Torez Smith <torez@redhat.com>
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Signed-off-by: Torez Smith <torez@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1570190373-30684-7-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Xhci re-enables a slot on transaction error in set_address using
xhci_disable_slot() + xhci_alloc_dev().
But in this case, xhci_alloc_dev() creates debugfs entries upon an
existing device without cleaning up old entries, thus memory leaks.
So this patch simply moves calling xhci_debugfs_free_dev() from
xhci_free_dev() to xhci_disable_slot().
[added "possible" to header as this is about failure codepath -Mathias]
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1567172356-12915-5-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb core is the only major place in the kernel that checks for
a non-NULL device dma_mask to see if a device is DMA capable. This
is generally a bad idea, as all major busses always set up a DMA mask,
even if the device is not DMA capable - in fact bus layers like PCI
can't even know if a device is DMA capable at enumeration time. This
leads to lots of workaround in HCD drivers, and also prevented us from
setting up a DMA mask for platform devices by default last time we
tried.
Replace this guess with an explicit HCD_DMA that is set by drivers that
appear to have DMA support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190816062435.881-4-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Usb core will reset the default control endpoint "ep0" before resetting
a device. if the endpoint has a valid pointer back to the usb device
then the xhci driver reset callback will try to clear the toggle for
the endpoint.
ep0 didn't use to have this pointer set as ep0 was always allocated
by default together with a xhci slot for the usb device. Other endpoints
got their usb device pointer set in xhci_add_endpoint()
This changed with commit ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
which sets the pointer for any endpoint on a FS/LS device behind a
HS hub that halts, including ep0.
If xHC controller needs to be reset at resume, then all the xhci slots
will be lost. Slots will be reenabled and reallocated at device reset,
but unlike other endpoints the ep0 is reset before device reset, while
the xhci slot may still be invalid, causing NULL pointer dereference.
Fix it by checking that the endpoint has both a usb device pointer and
valid xhci slot before trying to clear the toggle.
This issue was not seen earlier as ep0 didn't use to have a valid usb
device pointer, and other endpoints were only reset after device reset
when xhci slots were properly reenabled.
Reported-by: Bob Gleitsmann <rjgleits@bellsouth.net>
Reported-by: Enric Balletbo Serra <eballetbo@gmail.com>
Fixes: ef513be0a9 ("usb: xhci: Add Clear_TT_Buffer")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Link: https://lore.kernel.org/r/1564758044-24748-1-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.2 capability in a host can be detected from the
xHCI Supported Protocol Capability major and minor revision fields.
If major is 0x3 and minor 0x20 then the host is USB 3.2 capable.
For USB 3.2 capable hosts set the root hub lane count to 2.
The Major Revision and Minor Revision fields contain a BCD version number.
The value of the Major Revision field is JJh and the value of the Minor
Revision field is MNh for version JJ.M.N, where JJ = major revision number,
M - minor version number, N = sub-minor version number,
e.g. version 3.1 is represented with a value of 0310h.
Also fix the extra whitespace printed out when announcing regular
SuperSpeed hosts.
Cc: <stable@vger.kernel.org> # v4.18+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A USB3 device needs to be reset and re-enumarated if the port it
connects to goes to a error state, with link state inactive.
There is no use in trying to recover failed transactions by resetting
endpoints at this stage. Tests show that in rare cases, after multiple
endpoint resets of a roothub port the whole host controller might stop
completely.
Several retries to recover from transaction error can happen as
it can take a long time before the hub thread discovers the USB3
port error and inactive link.
We can't reliably detect the port error from slot or endpoint context
due to a limitation in xhci, see xhci specs section 4.8.3:
"There are several cases where the EP State field in the Output
Endpoint Context may not reflect the current state of an endpoint"
and
"Software should maintain an accurate value for EP State, by tracking it
with an internal variable that is driven by Events and Doorbell accesses"
Same appears to be true for slot state.
set a flag to the corresponding slot if a USB3 roothub port link goes
inactive to prevent both queueing new URBs and resetting endpoints.
Reported-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Tested-by: Rapolu Chiranjeevi <chiranjeevi.rapolu@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 2.0 specification chapter 11.17.5 says "as part of endpoint halt
processing for full-/low-speed endpoints connected via a TT, the host
software must use the Clear_TT_Buffer request to the TT to ensure
that the buffer is not in the busy state".
In our case, a full-speed speaker (ConferenceCam) is behind a high-
speed hub (ConferenceCam Connect), sometimes once we get STALL on a
request we may continue to get STALL with the folllowing requests,
like Set_Interface.
Here we invoke usb_hub_clear_tt_buffer() to send Clear_TT_Buffer
request to the hub of the device for the following Set_Interface
requests to the device to get ACK successfully.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Clear_TT_Buffer request sent to the hub includes the address of
the LS/FS child device in wValue field. usb_hub_clear_tt_buffer()
uses udev->devnum to set the address wValue. This won't work for
devices connected to xHC.
For other host controllers udev->devnum is the same as the address of
the usb device, chosen and set by usb core. With xHC the controller
hardware assigns the address, and won't be the same as devnum.
Here we add devaddr in "struct usb_device" for
usb_hub_clear_tt_buffer() to use.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
