The current guest mitigation of TAA is both too heavy and not really
sufficient. It is too heavy because it will cause some affected CPUs
(those that have MDS_NO but lack TAA_NO) to fall back to VERW and
get the corresponding slowdown. It is not really sufficient because
it will cause the MDS_NO bit to disappear upon microcode update, so
that VMs started before the microcode update will not be runnable
anymore afterwards, even with tsx=on.
Instead, if tsx=on on the host, we can emulate MSR_IA32_TSX_CTRL for
the guest and let it run without the VERW mitigation. Even though
MSR_IA32_TSX_CTRL is quite heavyweight, and we do not want to write
it on every vmentry, we can use the shared MSR functionality because
the host kernel need not protect itself from TSX-based side-channels.
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Because KVM always emulates CPUID, the CPUID clear bit
(bit 1) of MSR_IA32_TSX_CTRL must be emulated "manually"
by the hypervisor when performing said emulation.
Right now neither kvm-intel.ko nor kvm-amd.ko implement
MSR_IA32_TSX_CTRL but this will change in the next patch.
Reviewed-by: Jim Mattson <jmattson@google.com>
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
"Shared MSRs" are guest MSRs that are written to the host MSRs but
keep their value until the next return to userspace. They support
a mask, so that some bits keep the host value, but this mask is
only used to skip an unnecessary MSR write and the value written
to the MSR is always the guest MSR.
Fix this and, while at it, do not update smsr->values[slot].curr if
for whatever reason the wrmsr fails. This should only happen due to
reserved bits, so the value written to smsr->values[slot].curr
will not match when the user-return notifier and the host value will
always be restored. However, it is untidy and in rare cases this
can actually avoid spurious WRMSRs on return to userspace.
Cc: stable@vger.kernel.org
Reviewed-by: Jim Mattson <jmattson@google.com>
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM does not implement MSR_IA32_TSX_CTRL, so it must not be presented
to the guests. It is also confusing to have !ARCH_CAP_TSX_CTRL_MSR &&
!RTM && ARCH_CAP_TAA_NO: lack of MSR_IA32_TSX_CTRL suggests TSX was not
hidden (it actually was), yet the value says that TSX is not vulnerable
to microarchitectural data sampling. Fix both.
Cc: stable@vger.kernel.org
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
KVM/arm updates for Linux 5.5:
- Allow non-ISV data aborts to be reported to userspace
- Allow injection of data aborts from userspace
- Expose stolen time to guests
- GICv4 performance improvements
- vgic ITS emulation fixes
- Simplify FWB handling
- Enable halt pool counters
- Make the emulated timer PREEMPT_RT compliant
Conflicts:
include/uapi/linux/kvm.h
Move the static keyword to the front of declaration of
cpu_pmu_of_device_ids, and resolve the following compiler
warning that can be seen when building with warnings
enabled (W=1):
arch/nds32/kernel/perf_event_cpu.c:1122:1: warning:
‘static’ is not at beginning of declaration [-Wold-style-declaration]
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Acked-by: Greentime Hu <green.hu@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Many callsites want to fetch the values of system, user, user_nice, guest
or guest_nice kcpustat fields altogether or at least a pair of these.
In that case calling kcpustat_field() for each requested field brings
unecessary overhead when we could fetch all of them in a row.
So provide kcpustat_cpu_fetch() that fetches the whole kcpustat array
in a vtime safe way under the same RCU and seqcount block.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wanpeng Li <wanpengli@tencent.com>
Cc: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Link: https://lkml.kernel.org/r/20191121024430.19938-3-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Provide support for user, nice, guest and guest_nice fields through
kcpustat_field().
Whether we account the delta to a nice or not nice field is decided on
top of the nice value snapshot taken at the time we call kcpustat_field().
If the nice value of the task has been changed since the last vtime
update, we may have inacurrate distribution of the nice VS unnice
cputime.
However this is considered as a minor issue compared to the proper fix
that would involve interrupting the target on nice updates, which is
undesired on nohz_full CPUs.
Signed-off-by: Frederic Weisbecker <frederic@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wanpeng Li <wanpengli@tencent.com>
Cc: Yauheni Kaliuta <yauheni.kaliuta@redhat.com>
Link: https://lkml.kernel.org/r/20191121024430.19938-2-frederic@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Add support for the soft status and control register, which allows
TX_FAULT and RX_LOS to be monitored and TX_DISABLE to be set. We
make use of this when the board does not support GPIOs for these
signals.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Russell King says:
====================
Add rudimentary SFP module quirk support
The SFP module EEPROM describes the capabilities of the module, but
doesn't describe the host interface. We have a certain amount of
guess-work to work out how to configure the host - which works most
of the time.
However, there are some (such as GPON) modules which are able to
support different host interfaces, such as 1000BASE-X and 2500BASE-X.
The module will switch between each mode until it achieves link with
the host.
There is no defined way to describe this in the SFP EEPROM, so we can
only recognise the module and handle it appropriately. This series
adds the necessary recognition of the modules using a quirk system,
and tweaks the support mask to allow them to link with the host at
2500BASE-X, thereby allowing the user to achieve full line rate.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc Micalizzi reports that Huawei MA5671A and Alcatel/Lucent G-010S-P
modules are capable of 2500base-X, but incorrectly report their
capabilities in the EEPROM. It seems rather common that GPON modules
mis-report.
Let's fix these modules by adding some quirks.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
snprintf returns the number of chars that would be written, not number
of chars that were actually written. As such, 'offs' may get larger than
'tbl.maxlen', causing the 'tbl.maxlen - offs' being < 0, and since the
parameter is size_t, it would overflow.
Since using scnprintf may hide the limit error, while the buffer is still
enough now, let's just add a WARN_ON_ONCE in case it reach the limit
in future.
v2: Use WARN_ON_ONCE as Jiri and Eric suggested.
Suggested-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently collect_md gre tunnel will store the tunnel info(metadata_dst)
to skb_dst.
And now the non-tun-dst gre tunnel already can add tunnel header through
lwtunnel.
When received a arp_request on the non-tun-dst gre tunnel. The packet of
arp response will send through the non-tun-dst tunnel without tunnel info
which will lead the arp response packet to be dropped.
If the non-tun-dst gre tunnel also store the tunnel info as metadata_dst,
The arp response packet will set the releted tunnel info in the
iptunnel_metadata_reply.
The following is the test script:
ip netns add cl
ip l add dev vethc type veth peer name eth0 netns cl
ifconfig vethc 172.168.0.7/24 up
ip l add dev tun1000 type gretap key 1000
ip link add user1000 type vrf table 1
ip l set user1000 up
ip l set dev tun1000 master user1000
ifconfig tun1000 10.0.1.1/24 up
ip netns exec cl ifconfig eth0 172.168.0.17/24 up
ip netns exec cl ip l add dev tun type gretap local 172.168.0.17 remote 172.168.0.7 key 1000
ip netns exec cl ifconfig tun 10.0.1.7/24 up
ip r r 10.0.1.7 encap ip id 1000 dst 172.168.0.17 key dev tun1000 table 1
With this patch
ip netns exec cl ping 10.0.1.1 can success
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to check the host page size is big enough to accomodate the
EQ. Let's do this before taking a reference on the EQ page to avoid
a potential leak if the check fails.
Cc: stable@vger.kernel.org # v5.2
Fixes: 13ce3297c5 ("KVM: PPC: Book3S HV: XIVE: Add controls for the EQ configuration")
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
The EQ page is allocated by the guest and then passed to the hypervisor
with the H_INT_SET_QUEUE_CONFIG hcall. A reference is taken on the page
before handing it over to the HW. This reference is dropped either when
the guest issues the H_INT_RESET hcall or when the KVM device is released.
But, the guest can legitimately call H_INT_SET_QUEUE_CONFIG several times,
either to reset the EQ (vCPU hot unplug) or to set a new EQ (guest reboot).
In both cases the existing EQ page reference is leaked because we simply
overwrite it in the XIVE queue structure without calling put_page().
This is especially visible when the guest memory is backed with huge pages:
start a VM up to the guest userspace, either reboot it or unplug a vCPU,
quit QEMU. The leak is observed by comparing the value of HugePages_Free in
/proc/meminfo before and after the VM is run.
Ideally we'd want the XIVE code to handle the EQ page de-allocation at the
platform level. This isn't the case right now because the various XIVE
drivers have different allocation needs. It could maybe worth introducing
hooks for this purpose instead of exposing XIVE internals to the drivers,
but this is certainly a huge work to be done later.
In the meantime, for easier backport, fix both vCPU unplug and guest reboot
leaks by introducing a wrapper around xive_native_configure_queue() that
does the necessary cleanup.
Reported-by: Satheesh Rajendran <sathnaga@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # v5.2
Fixes: 13ce3297c5 ("KVM: PPC: Book3S HV: XIVE: Add controls for the EQ configuration")
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Tested-by: Lijun Pan <ljp@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
On PowerNV the PCIe topology is (currently) managed by the powernv platform
code in Linux in cooperation with the platform firmware. Linux's native
PCIe port service drivers operate independently of both and this can cause
problems.
The main issue is that the portbus driver will conflict with the platform
specific hotplug driver (pnv_php) over ownership of the MSI used to notify
the host when a hotplug event occurs. The portbus driver claims this MSI on
behalf of the individual port services because the same interrupt is used
for hotplug events, PMEs (on root ports), and link bandwidth change
notifications. The portbus driver will always claim the interrupt even if
the individual port service drivers, such as pciehp, are compiled out.
The second, bigger, problem is that the hotplug port service driver
fundamentally does not work on PowerNV. The platform assumes that all
PCI devices have a corresponding arch-specific handle derived from the DT
node for the device (pci_dn) and without one the platform will not allow
a PCI device to be enabled. This problem is largely due to historical
baggage, but it can't be resolved without significant re-factoring of the
platform PCI support.
We can fix these problems in the interim by setting the
"pcie_ports_disabled" flag during platform initialisation. The flag
indicates the platform owns the PCIe ports which stops the portbus driver
from being registered.
This does have the side effect of disabling all port services drivers
that is: AER, PME, BW notifications, hotplug, and DPC. However, this is
not a huge disadvantage on PowerNV since these services are either unused
or handled through other means.
Fixes: 66725152fb ("PCI/hotplug: PowerPC PowerNV PCI hotplug driver")
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191118065553.30362-1-oohall@gmail.com
There is a config item CONFIG_SIMPLE_GPIO which
provides simple memory mapped GPIOs specific to powerpc.
However, the only platform which selects this option is
mpc5200, and this platform doesn't use it.
There are three boards calling simple_gpiochip_init(), but
as they don't select CONFIG_SIMPLE_GPIO, this is just a nop.
Simple_gpio is just redundant with the generic MMIO GPIO
driver which can be found in driver/gpio/ and selected via
CONFIG_GPIO_GENERIC_PLATFORM, so drop simple_gpio driver.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/bf930402613b41b42d0441b784e0cc43fc18d1fb.1572529632.git.christophe.leroy@c-s.fr
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-11-20
The following pull-request contains BPF updates for your *net-next* tree.
We've added 81 non-merge commits during the last 17 day(s) which contain
a total of 120 files changed, 4958 insertions(+), 1081 deletions(-).
There are 3 trivial conflicts, resolve it by always taking the chunk from
196e8ca748:
<<<<<<< HEAD
=======
void *bpf_map_area_mmapable_alloc(u64 size, int numa_node);
>>>>>>> 196e8ca748
<<<<<<< HEAD
void *bpf_map_area_alloc(u64 size, int numa_node)
=======
static void *__bpf_map_area_alloc(u64 size, int numa_node, bool mmapable)
>>>>>>> 196e8ca748
<<<<<<< HEAD
if (size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
=======
/* kmalloc()'ed memory can't be mmap()'ed */
if (!mmapable && size <= (PAGE_SIZE << PAGE_ALLOC_COSTLY_ORDER)) {
>>>>>>> 196e8ca748
The main changes are:
1) Addition of BPF trampoline which works as a bridge between kernel functions,
BPF programs and other BPF programs along with two new use cases: i) fentry/fexit
BPF programs for tracing with practically zero overhead to call into BPF (as
opposed to k[ret]probes) and ii) attachment of the former to networking related
programs to see input/output of networking programs (covering xdpdump use case),
from Alexei Starovoitov.
2) BPF array map mmap support and use in libbpf for global data maps; also a big
batch of libbpf improvements, among others, support for reading bitfields in a
relocatable manner (via libbpf's CO-RE helper API), from Andrii Nakryiko.
3) Extend s390x JIT with usage of relative long jumps and loads in order to lift
the current 64/512k size limits on JITed BPF programs there, from Ilya Leoshkevich.
4) Add BPF audit support and emit messages upon successful prog load and unload in
order to have a timeline of events, from Daniel Borkmann and Jiri Olsa.
5) Extension to libbpf and xdpsock sample programs to demo the shared umem mode
(XDP_SHARED_UMEM) as well as RX-only and TX-only sockets, from Magnus Karlsson.
6) Several follow-up bug fixes for libbpf's auto-pinning code and a new API
call named bpf_get_link_xdp_info() for retrieving the full set of prog
IDs attached to XDP, from Toke Høiland-Jørgensen.
7) Add BTF support for array of int, array of struct and multidimensional arrays
and enable it for skb->cb[] access in kfree_skb test, from Martin KaFai Lau.
8) Fix AF_XDP by using the correct number of channels from ethtool, from Luigi Rizzo.
9) Two fixes for BPF selftest to get rid of a hang in test_tc_tunnel and to avoid
xdping to be run as standalone, from Jiri Benc.
10) Various BPF selftest fixes when run with latest LLVM trunk, from Yonghong Song.
11) Fix a memory leak in BPF fentry test run data, from Colin Ian King.
12) Various smaller misc cleanups and improvements mostly all over BPF selftests and
samples, from Daniel T. Lee, Andre Guedes, Anders Roxell, Mao Wenan, Yue Haibing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On compat interfaces, the high order bits of nanoseconds should be zeroed
out. This is because the application code or the libc do not guarantee
zeroing of these. If used without zeroing, kernel might be at risk of using
timespec values incorrectly.
Originally it was handled correctly, but lost during is_compat_syscall()
cleanup. Revert the condition back to check CONFIG_64BIT.
Fixes: 98f76206b3 ("compat: Cleanup in_compat_syscall() callers")
Reported-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Dmitry Safonov <dima@arista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20191121000303.126523-1-dima@arista.com
For fine grained dpm, there is only two levels supported. However
to reflect correctly the current clock frequency, there is an
intermediate level faked. Thus on forcing level setting, we
need to treat level 2 correctly as level 1.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
