We were sending malformed EOMA with total message size set to 0. This
issue has been fixed in the previous patch.
In this patch a sanity check is added to the RX path and a error message
is displayed.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Filters array is coped from user space and linked to the j1939 socket.
On socket release this memory was not freed.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Currently the error return paths do not free skb and this results in a
memory leak. Fix this by freeing them before the return.
Addresses-Coverity: ("Resource leak")
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While the ti_hecc has interrupts to report when the error counters increase
to a certain level and which change state it doesn't handle the case that
the error counters go down again, so the reported state can actually be
wrong. Since there is no interrupt for that, do update state based on the
error counters, when the state is not error active and goes down again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The HECC_CANES register handles the flags specially, it only updates
the flags after a one is written to them. Since the interrupt for
frame errors is not enabled an old error can hence been seen when a
state interrupt arrives. For example if the device is not connected
to the CAN-bus the error warning interrupt will have HECC_CANES
indicating there is no ack. The error passive interrupt thereafter
will have HECC_CANES flagging that there is a warning level. And if
thereafter there is a message successfully send HECC_CANES points to
an error passive event, while in reality it became error warning
again. In summary, the state is not always reported correctly.
So handle the state changes and frame errors separately. The state
changes are now based on the interrupt flags and handled directly
when they occur. The reporting of the frame errors is still done as
before, as a side effect of another interrupt.
note: the hecc_clear_bit will do a read, modify, write. So it will
not only clear the bit, but also reset all other bits being set as
a side affect, hence it is replaced with only clearing the flags.
note: The HECC_CANMC_CCR is no longer cleared in the state change
interrupt, it is completely unrelated.
And use net_ratelimit to make checkpatch happy.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the rx FIFO overflows the ti_hecc would silently drop them since
the overwrite protection is enabled for all mailboxes. So disable it for
the lowest priority mailbox and return a proper error value when receive
message lost is set. Drop the message itself in that case, since it
might be partially updated.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Release the mailbox after reading it, so it can be reused a bit earlier.
Since "can: rx-offload: continue on error" all pending message bits are
cleared directly, so remove clearing them in ti_hecc.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The HECC_CANMIM is set in the xmit path and cleared in the interrupt.
Since this is done with a read, modify, write action the register might
end up with some more MIM enabled then intended, since it is not
protected. That doesn't matter at all, since the tx interrupt disables
the mailbox with HECC_CANME (while holding a spinlock). So lets just
always keep MIM set.
While at it, since the mailbox direction never changes, don't set it
every time a message is send, ti_hecc_reset() already sets them to tx.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the interface goes down, the CPK should no longer take an active
part in the CAN-bus communication, like sending acks and error frames.
So enable configuration mode in ti_hecc_stop, so the CPK is no longer
active.
When a transceiver switch is present the acks and errors don't make it
to the bus, but disabling the CPK then does prevent oddities, like
ti_hecc_reset() failing, since the CPK can become bus-off and starts
counting the 11 bit recessive bits, which seems to block the reset. It
can also cause invalid interrupts and disrupt the CAN-bus, since
transmission can be stopped in the middle of a message, by disabling the
tranceiver while the CPK is sending.
Since the CPK is disabled after normal power on, it is typically only
seen when the interface is restarted.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.
In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.
Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.
Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.
With this patch the loop is left in case of empty FIFO, but not on
errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.
Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Before this patch can_rx_offload_offload_one() returns a pointer to a
skb containing the read CAN frame or a NULL pointer.
However the meaning of the NULL pointer is ambiguous, it can either mean
the requested mailbox is empty or there was an error.
This patch fixes this situation by returning:
- pointer to skb on success
- NULL pointer if mailbox is empty
- ERR_PTR() in case of an error
All users of can_rx_offload_offload_one() have been adopted, no
functional change intended.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the rx-offload skb_queue is full or the skb allocation fails (due to OOM),
the mailbox contents is discarded.
This patch adds the incrementing of the rx_fifo_errors statistics counter.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The skb_queue is a linked list, holding the skb to be processed in the
next NAPI call.
Without this patch, the queue length in can_rx_offload_offload_one() is
limited to skb_queue_len_max + 1. As the skb_queue is a linked list, no
array or other resources are accessed out-of-bound, however this
behaviour is counterintuitive.
This patch limits the rx-offload skb_queue length to skb_queue_len_max.
Fixes: d254586c34 ("can: rx-offload: Add support for HW fifo based irq offloading")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the rx-offload skb_queue is full can_rx_offload_queue_tail() will not
queue the skb and return with an error.
This patch frees the skb in case of a full queue, which brings
can_rx_offload_queue_tail() in line with the
can_rx_offload_queue_sorted() function, which has been adjusted in the
previous patch.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the caller.
Fixes: d254586c34 ("can: rx-offload: Add support for HW fifo based irq offloading")
Reported-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If the rx-offload skb_queue is full can_rx_offload_queue_sorted() will
not queue the skb and return with an error.
None of the callers of this function, issue a kfree_skb() to free the
not queued skb. This results in a memory leak.
This patch fixes the problem by freeing the skb in case of a full queue.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the callers, as this function might
be used in both the rx and tx path.
Fixes: 55059f2b7f ("can: rx-offload: introduce can_rx_offload_get_echo_skb() and can_rx_offload_queue_sorted() functions")
Cc: linux-stable <stable@vger.kernel.org>
Cc: Martin Hundebøll <martin@geanix.com>
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
AXI CANIP doesn't support tx fifo empty interrupt feature(TXFEMP),
update the flags filed in the driver for AXI CAN case accordingly.
Fixes: 3281b380ec ("can: xilinx_can: Fix flags field initialization for axi can and canps")
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While the state is updated when the error counters increase and
decrease, there is no event when the bus recovers and the error counters
decrease again. So add that event as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Tested-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When the status register is read without the status IRQ pending, the
chip may not raise the interrupt line for an upcoming status interrupt
and the driver may miss a status interrupt.
It is critical that the BUSOFF status interrupt is forwarded to the
higher layers, since no more interrupts will follow without
intervention.
Thanks to Wolfgang and Joe for bringing up the first idea.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Joe Burmeister <joe.burmeister@devtank.co.uk>
Fixes: fa39b54ccf ("can: c_can: Get rid of pointless interrupts")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fix a small slab info leak due to a failure to clear the command buffer
at allocation.
The first 16 bytes of the command buffer are always sent to the device
in pcan_usb_send_cmd() even though only the first two may have been
initialised in case no argument payload is provided (e.g. when waiting
for a response).
Fixes: bb4785551f ("can: usb: PEAK-System Technik USB adapters driver core")
Cc: stable <stable@vger.kernel.org> # 3.4
Reported-by: syzbot+863724e7128e14b26732@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When decoding a buffer received from PCAN-USB, the first timestamp read in
a packet is a 16-bit coded time base, and the next ones are an 8-bit
offset to this base, regardless of the type of packet read.
This patch corrects a potential loss of synchronization by using a
timestamp index read from the buffer, rather than an index of received
data packets, to determine on the sizeof the timestamp to be read from the
packet being decoded.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Fixes: 46be265d33 ("can: usb: PEAK-System Technik PCAN-USB specific part")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The ECC (memory error detection and correction) mechanism can be
activated or not, controlled by the ECCDIS bit in CAN_MECR. When
disabled, updates on indications and reporting registers are stopped.
So if want to disable ECC completely, had better assert ECCDIS bit, not
just mask the related interrupts.
Fixes: cdce844865 ("can: flexcan: add vf610 support for FlexCAN")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In gs_can_open() if usb_submit_urb() fails the allocated urb should be
released.
Fixes: d08e973a77 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
of_node_put() needs to be called when the device node which is got
from of_get_child_by_name() finished using.
Fixes: 2290aefa2e ("can: dev: Add support for limiting configured bitrate")
Cc: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The two ioctls START_SYNC and WAIT_SYNC were mistakenly marked as
deprecated and scheduled for removal but we actualy do use them for
'btrfs subvolume delete -C/-c'. The deprecated thing in ebc87351e5
should have been just the async flag for subvolume creation.
The deprecation has been added in this development cycle, remove it
until it's time.
Fixes: ebc87351e5 ("btrfs: Deprecate BTRFS_SUBVOL_CREATE_ASYNC flag")
Signed-off-by: David Sterba <dsterba@suse.com>
We hit a regression while rolling out 5.2 internally where we were
hitting the following panic
kernel BUG at mm/page-writeback.c:2659!
RIP: 0010:clear_page_dirty_for_io+0xe6/0x1f0
Call Trace:
__process_pages_contig+0x25a/0x350
? extent_clear_unlock_delalloc+0x43/0x70
submit_compressed_extents+0x359/0x4d0
normal_work_helper+0x15a/0x330
process_one_work+0x1f5/0x3f0
worker_thread+0x2d/0x3d0
? rescuer_thread+0x340/0x340
kthread+0x111/0x130
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x1f/0x30
This is happening because the page is not locked when doing
clear_page_dirty_for_io. Looking at the core dump it was because our
async_extent had a ram_size of 24576 but our async_chunk range only
spanned 20480, so we had a whole extra page in our ram_size for our
async_extent.
This happened because we try not to compress pages outside of our
i_size, however a cleanup patch changed us to do
actual_end = min_t(u64, i_size_read(inode), end + 1);
which is problematic because i_size_read() can evaluate to different
values in between checking and assigning. So either an expanding
truncate or a fallocate could increase our i_size while we're doing
writeout and actual_end would end up being past the range we have
locked.
I confirmed this was what was happening by installing a debug kernel
that had
actual_end = min_t(u64, i_size_read(inode), end + 1);
if (actual_end > end + 1) {
printk(KERN_ERR "KABOOM\n");
actual_end = end + 1;
}
and installing it onto 500 boxes of the tier that had been seeing the
problem regularly. Last night I got my debug message and no panic,
confirming what I expected.
[ dsterba: the assembly confirms a tiny race window:
mov 0x20(%rsp),%rax
cmp %rax,0x48(%r15) # read
movl $0x0,0x18(%rsp)
mov %rax,%r12
mov %r14,%rax
cmovbe 0x48(%r15),%r12 # eval
Where r15 is inode and 0x48 is offset of i_size.
The original fix was to revert 62b3762271 that would do an
intermediate assignment and this would also avoid the doulble
evaluation but is not future-proof, should the compiler merge the
stores and call i_size_read anyway.
There's a patch adding READ_ONCE to i_size_read but that's not being
applied at the moment and we need to fix the bug. Instead, emulate
READ_ONCE by two barrier()s that's what effectively happens. The
assembly confirms single evaluation:
mov 0x48(%rbp),%rax # read once
mov 0x20(%rsp),%rcx
mov $0x20,%edx
cmp %rax,%rcx
cmovbe %rcx,%rax
mov %rax,(%rsp)
mov %rax,%rcx
mov %r14,%rax
Where 0x48(%rbp) is inode->i_size stored to %eax.
]
Fixes: 62b3762271 ("btrfs: Remove isize local variable in compress_file_range")
CC: stable@vger.kernel.org # v5.1+
Reviewed-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ changelog updated ]
Signed-off-by: David Sterba <dsterba@suse.com>
When doing cat /proc/<PID>/stack, the output is missing the first entry.
When the current code walks the stack starting in stack_trace_save_tsk,
it skips all scheduler functions (that's OK) plus one more function. But
this one function should be skipped only for the 'current' task as it is
stack_trace_save_tsk proper.
The original code (before the common infrastructure) skipped one
function only for the 'current' task -- see save_stack_trace_tsk before
3599fe12a1. So do so also in the new infrastructure now.
Fixes: 214d8ca6ee ("stacktrace: Provide common infrastructure")
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Michal Suchanek <msuchanek@suse.de>
Acked-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lkml.kernel.org/r/20191030072545.19462-1-jslaby@suse.cz
Cpupower tool has set and info options which are being used only by
x86 machines. This patch removes support for these two subcommands
from cpupower utility for POWER. Thus, these two subcommands will now be
available only for intel.
This removes the ambiguous error message while using set option in case
of using non-intel systems.
Without this patch on a POWER system:
root@ubuntu:~# cpupower info
System does not support Intel's performance bias setting
root@ubuntu:~# cpupower set -b 10
Error setting perf-bias value on CPU
With this patch on a POWER box:
root@ubuntu:~# cpupower info
Subcommand not supported on POWER
Same result for set subcommand.
This patch does not affect results on a intel box.
Signed-off-by: Abhishek Goel <huntbag@linux.vnet.ibm.com>
Acked-by: Thomas Renninger <trenn@suse.de>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add zero copy AF_XDP support. This patch adds zero copy support for
Tx and Rx; code for zero copy is added to ice_xsk.h and ice_xsk.c.
For Tx, implement ndo_xsk_wakeup. As with other drivers, reuse
existing XDP Tx queues for this task, since XDP_REDIRECT guarantees
mutual exclusion between different NAPI contexts based on CPU ID. In
turn, a netdev can XDP_REDIRECT to another netdev with a different
NAPI context, since the operation is bound to a specific core and each
core has its own hardware ring.
For Rx, allocate frames as MEM_TYPE_ZERO_COPY on queues that AF_XDP is
enabled.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Between VMSAv8-64 and the various 32-bit formats, there is either one
64-bit MAIR or a pair of 32-bit MAIR0/MAIR1 or NMRR/PMRR registers.
As such, keeping two 64-bit values in io_pgtable_cfg has always been
overkill.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
The nature of the LPAE format means that data->pg_shift is always
redundant with data->bits_per_level, since they represent the size of a
page and the number of PTEs per page respectively, and the size of a PTE
is constant. Thus it works out more efficient to only store the latter,
and derive the former via a trivial addition where necessary.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
[will: Reworked granule check in iopte_to_paddr()]
Signed-off-by: Will Deacon <will@kernel.org>
Jozsef Kadlecsik says:
====================
ipset patches for nf
- Fix the error code in ip_set_sockfn_get() when copy_to_user() is used,
from Dan Carpenter.
- The IPv6 part was missed when fixing copying the right MAC address
in the patch "netfilter: ipset: Copy the right MAC address in bitmap:ip,mac
and hash:ip,mac sets", it is completed now by Stefano Brivio.
- ipset nla_policies are fixed to fully support NL_VALIDATE_STRICT and
the code is converted from deprecated parsings to verified ones.
====================
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Do not try to bind a chain again if it exists, otherwise the driver
returns EBUSY.
Fixes: c9626a2cbd ("netfilter: nf_tables: add hardware offload support")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Userspace never includes the NFT_BASE_CHAIN flag, this flag is inferred
from the NFTA_CHAIN_HOOK atribute. The chain update path does not allow
to update flags at this stage, the existing sanity check bogusly hits
EOPNOTSUPP in the basechain case if the offload flag is set on.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
xt_in() returns NULL in the output hook, skip the pkt_type change for
that case, redirection only makes sense in broute/prerouting hooks.
Reported-by: Tom Yan <tom.ty89@gmail.com>
Cc: Linus Lüssing <linus.luessing@c0d3.blue>
Fixes: cf3cb246e2 ("bridge: ebtables: fix reception of frames DNAT-ed to bridge device/port")
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
If the object type doesn't implement an update operation and the user tries to
update it will silently ignore the update operation.
Fixes: aa4095a156 ("netfilter: nf_tables: fix possible null-pointer dereference in object update")
Signed-off-by: Fernando Fernandez Mancera <ffmancera@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Invoking the following commands on a 32-bit architecture with strict
alignment requirements (such as an ARMv7-based Raspberry Pi) results
in an alignment exception:
# nft add table ip test-ip4
# nft add chain ip test-ip4 output { type filter hook output priority 0; }
# nft add rule ip test-ip4 output quota 1025 bytes
Alignment trap: not handling instruction e1b26f9f at [<7f4473f8>]
Unhandled fault: alignment exception (0x001) at 0xb832e824
Internal error: : 1 [#1] PREEMPT SMP ARM
Hardware name: BCM2835
[<7f4473fc>] (nft_quota_do_init [nft_quota])
[<7f447448>] (nft_quota_init [nft_quota])
[<7f4260d0>] (nf_tables_newrule [nf_tables])
[<7f4168dc>] (nfnetlink_rcv_batch [nfnetlink])
[<7f416bd0>] (nfnetlink_rcv [nfnetlink])
[<8078b334>] (netlink_unicast)
[<8078b664>] (netlink_sendmsg)
[<8071b47c>] (sock_sendmsg)
[<8071bd18>] (___sys_sendmsg)
[<8071ce3c>] (__sys_sendmsg)
[<8071ce94>] (sys_sendmsg)
The reason is that nft_quota_do_init() calls atomic64_set() on an
atomic64_t which is only aligned to 32-bit, not 64-bit, because it
succeeds struct nft_expr in memory which only contains a 32-bit pointer.
Fix by aligning the nft_expr private data to 64-bit.
Fixes: 96518518cc ("netfilter: add nftables")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.13+
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since v5.2 (commit "netlink: re-add parse/validate functions in strict
mode") NL_VALIDATE_STRICT is enabled. Fix the ipset nla_policies which did
not support strict mode and convert from deprecated parsings to verified ones.
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
Same as commit 1b4a75108d ("netfilter: ipset: Copy the right MAC
address in bitmap:ip,mac and hash:ip,mac sets"), another copy and paste
went wrong in commit 8cc4ccf583 ("netfilter: ipset: Allow matching on
destination MAC address for mac and ipmac sets").
When I fixed this for IPv4 in 1b4a75108d, I didn't realise that
hash:ip,mac sets also support IPv6 as family, and this is covered by a
separate function, hash_ipmac6_kadt().
In hash:ip,mac sets, the first dimension is the IP address, and the
second dimension is the MAC address: check the IPSET_DIM_TWO_SRC flag
in flags while deciding which MAC address to copy, destination or
source.
This way, mixing source and destination matches for the two dimensions
of ip,mac hash type works as expected, also for IPv6. With this setup:
ip netns add A
ip link add veth1 type veth peer name veth2 netns A
ip addr add 2001:db8::1/64 dev veth1
ip -net A addr add 2001:db8::2/64 dev veth2
ip link set veth1 up
ip -net A link set veth2 up
dst=$(ip netns exec A cat /sys/class/net/veth2/address)
ip netns exec A ipset create test_hash hash:ip,mac family inet6
ip netns exec A ipset add test_hash 2001:db8::1,${dst}
ip netns exec A ip6tables -A INPUT -p icmpv6 --icmpv6-type 135 -j ACCEPT
ip netns exec A ip6tables -A INPUT -m set ! --match-set test_hash src,dst -j DROP
ipset now correctly matches a test packet:
# ping -c1 2001:db8::2 >/dev/null
# echo $?
0
Reported-by: Chen, Yi <yiche@redhat.com>
Fixes: 8cc4ccf583 ("netfilter: ipset: Allow matching on destination MAC address for mac and ipmac sets")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
The copy_to_user() function returns the number of bytes remaining to be
copied. In this code, that positive return is checked at the end of the
function and we return zero/success. What we should do instead is
return -EFAULT.
Fixes: a7b4f989a6 ("netfilter: ipset: IP set core support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@netfilter.org>
