All callers for process_mad allocate MAD structures with proper sizes,
there is no need to recheck it.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
This fixes the following DT schemas check errors:
meson-gxbb-nanopi-k2.dt.yaml: i2c@8500: compatible: Additional items are not allowed ('amlogic,meson-gxbb-i2c' was unexpected)
meson-gxbb-nanopi-k2.dt.yaml: i2c@8500: compatible:0: 'amlogic,meson-gx-i2c' is not one of ['amlogic,meson6-i2c', 'amlogic,meson-gxbb-i2c', 'amlogic,meson-axg-i2c']
meson-gxbb-nanopi-k2.dt.yaml: i2c@8500: compatible: ['amlogic,meson-gx-i2c', 'amlogic,meson-gxbb-i2c'] is too long
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxl-s905x-hwacom-amazetv.dt.yaml: cec@100: 'hdmi-phandle' is a required property
meson-gxm-rbox-pro.dt.yaml: cec@100: 'hdmi-phandle' is a required property
because CEC is not enabled on these boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-g12b-odroid-n2.dt.yaml: /: compatible: ['hardkernel,odroid-n2', 'amlogic,g12b'] is not valid under any of the given schemas
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-gxm-khadas-vim2.dt.yaml: gpu@c0000: interrupt-names:0: 'job' was expected
meson-gxm-khadas-vim2.dt.yaml: gpu@c0000: interrupt-names:2: 'gpu' was expected
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This fixes the following DT schemas check errors:
meson-g12b-s922x-khadas-vim3.dt.yaml: gpu@ffe40000: interrupt-names:0: 'job' was expected
meson-g12b-s922x-khadas-vim3.dt.yaml: gpu@ffe40000: interrupt-names:2: 'gpu' was expected
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Following commit 73e86cb03c ("arm64: Move PTE_RDONLY bit handling out
of set_pte_at()"), the PTE_RDONLY bit is no longer managed by
set_pte_at() but built into the PAGE_* attribute definitions.
Consequently, pte_same() must include this bit when checking two PTEs
for equality.
Remove the arm64-specific pte_same() function, practically reverting
commit 747a70e60b ("arm64: Fix copy-on-write referencing in HugeTLB")
Fixes: 73e86cb03c ("arm64: Move PTE_RDONLY bit handling out of set_pte_at()")
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Will Deacon <will@kernel.org>
Cc: Steve Capper <steve.capper@arm.com>
Reported-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Pull Samsung clk driver updates from Sylwester Nawrocki:
- Addition of rate table for the VPLL and GPU related clock
tree definition update to allow the GPU driver for setting
the GPU's clock without requiring detailed knowledge of
clock topology on each exynos542x SoC
- Fix for potential CPU performance degradation after system
suspend/resume cycle on exynos542x SoCs
* tag 'clk-v5.5-samsung' of https://git.kernel.org/pub/scm/linux/kernel/git/snawrocki/clk:
clk: samsung: exynos5420: Add SET_RATE_PARENT flag to clocks on G3D path
clk: samsung: exynos5420: Preserve CPU clocks configuration during suspend/resume
clk: samsung: exynos5420: Add VPLL rate table
clk: samsung: exynos5420: Preserve PLL configuration during suspend/resume
clk: samsung: exynos542x: Move G3D subsystem clocks to its sub-CMU
clk: samsung: exynos5433: Fix error paths
Pull Amlogic clk updates from Jerome Brunet:
- Add sm1 support in the Amlogic audio clock controller
* tag 'clk-meson-v5.5-1' of https://github.com/BayLibre/clk-meson:
clk: meson: axg-audio: use devm_platform_ioremap_resource() to simplify code
clk: meson: axg_audio: add sm1 support
clk: meson: axg-audio: provide clk top signal name
clk: meson: axg-audio: prepare sm1 addition
clk: meson: axg-audio: fix regmap last register
clk: meson: axg-audio: remove useless defines
dt-bindings: clock: meson: add sm1 resets to the axg-audio controller
dt-bindings: clk: axg-audio: add sm1 bindings
clk: meson: g12a: set CLK_MUX_ROUND_CLOSEST on the cpu clock muxes
clk: meson: g12a: fix cpu clock rate setting
clk: meson: gxbb: let sar_adc_clk_div set the parent clock rate
[Why]
doing kthread_park()/unpark() from drm_sched_entity_fini
while GPU reset is in progress defeats all the purpose of
drm_sched_stop->kthread_park.
If drm_sched_entity_fini->kthread_unpark() happens AFTER
drm_sched_stop->kthread_park nothing prevents from another
(third) thread to keep submitting job to HW which will be
picked up by the unparked scheduler thread and try to submit
to HW but fail because the HW ring is deactivated.
[How]
grab the reset lock before calling drm_sched_entity_fini()
Signed-off-by: Shirish S <shirish.s@amd.com>
Suggested-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Chip on the board is S905D3 not S905X3:
[ 0.098998] soc soc0: Amlogic Meson SM1 (S905D3) Revision 2b:c (b0:2) Detected
Change from v1: use 0xf0 mask instead of 0xf2 as advised by Neil Armstrong.
Fixes: 1d7c541b8a ("soc: amlogic: meson-gx-socinfo: Add S905X3 ID for VIM3L")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Added tests for u8/u32 clear value, u8/16 retain value, u16/32 invert value,
u8/u16/u32 preserve value and test for negative offsets.
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netdevsim object is reused by all the tests, but the resource
tests puts it into a broken state (failed reload in a different
namespace). Make sure it's fixed up at the end of that test
otherwise subsequent tests fail.
Fixes: b74c37fd35 ("selftests: netdevsim: add tests for devlink reload with resources")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when cross compiling perf tool for ARM64 on my x86 machine I
get this error:
arch/arm64/util/sym-handling.c:9:10: fatal error: gelf.h: No such file or directory
#include <gelf.h>
For the build, libelf is reported off:
Auto-detecting system features:
...
... libelf: [ OFF ]
Indeed, test-libelf is not built successfully:
more ./build/feature/test-libelf.make.output
test-libelf.c:2:10: fatal error: libelf.h: No such file or directory
#include <libelf.h>
^~~~~~~~~~
compilation terminated.
I have no such problems natively compiling on ARM64, and I did not
previously have this issue for cross compiling. Fix by relocating the
gelf.h include.
Signed-off-by: John Garry <john.garry@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Link: http://lore.kernel.org/lkml/1573045254-39833-1-git-send-email-john.garry@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Doug Berger says:
====================
net: bcmgenet: restore internal EPHY support (part 2)
This is a follow up to my previous submission (see [1]).
The first commit provides what is intended to be a complete solution
for the issues that can result from insufficient clocking of the MAC
during reset of its state machines. It should be backported to the
stable releases.
It is intended to replace the partial solution of commit 1f51548627
("net: bcmgenet: soft reset 40nm EPHYs before MAC init") which is
reverted by the second commit of this series and should not be back-
ported as noted in [2].
The third commit corrects a timing hazard with a polled PHY that can
occur when the MAC resumes and also when a v3 internal EPHY is reset
by the change in commit 25382b991d ("net: bcmgenet: reset 40nm EPHY
on energy detect"). It is expected that commit 25382b991d be back-
ported to stable first before backporting this commit.
[1] https://lkml.org/lkml/2019/10/16/1706
[2] https://lkml.org/lkml/2019/10/31/749
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_init_hw() function may reset the PHY to a configuration
that does not match manual network settings stored in the phydev
structure. If the phy state machine is polled rather than event
driven this can create a timing hazard where the phy state machine
might alter the settings stored in the phydev structure from the
value read from the BMCR.
This commit follows invocations of phy_init_hw() by the bcmgenet
driver with invocations of the genphy_config_aneg() function to
ensure that the BMCR is written to match the settings held in the
phydev structure. This prevents the risk of manual settings being
accidentally altered.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1f51548627.
This commit improved the chances of the umac resetting cleanly by
ensuring that the PHY was restored to its normal operation prior
to resetting the umac. However, there were still cases when the
PHY might not be driving a Tx clock to the umac during this window
(e.g. when the PHY detects no link).
The previous commit now ensures that the unimac receives clocks
from the MAC during its reset window so this commit is no longer
needed. This commit also has an unintended negative impact on the
MDIO performance of the UniMAC MDIO interface because it is used
before the MDIO interrupts are reenabled, so it should be removed.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted in commit 28c2d1a7a0 ("net: bcmgenet: enable loopback
during UniMAC sw_reset") the UniMAC must be clocked while sw_reset
is asserted for its state machines to reset cleanly.
The transmit and receive clocks used by the UniMAC are derived from
the signals used on its PHY interface. The bcmgenet MAC can be
configured to work with different PHY interfaces including MII,
GMII, RGMII, and Reverse MII on internal and external interfaces.
Unfortunately for the UniMAC, when configured for MII the Tx clock
is always driven from the PHY which places it outside of the direct
control of the MAC.
The earlier commit enabled a local loopback mode within the UniMAC
so that the receive clock would be derived from the transmit clock
which addressed the observed issue with an external GPHY disabling
it's Rx clock. However, when a Tx clock is not available this
loopback is insufficient.
This commit implements a workaround that leverages the fact that
the MAC can reliably generate all of its necessary clocking by
enterring the external GPHY RGMII interface mode with the UniMAC in
local loopback during the sw_reset interval. Unfortunately, this
has the undesirable side efect of the RGMII GTXCLK signal being
driven during the same window.
In most configurations this is a benign side effect as the signal
is either not routed to a pin or is already expected to drive the
pin. The one exception is when an external MII PHY is expected to
drive the same pin with its TX_CLK output creating output driver
contention.
This commit exploits the IEEE 802.3 clause 22 standard defined
isolate mode to force an external MII PHY to present a high
impedance on its TX_CLK output during the window to prevent any
contention at the pin.
The MII interface is used internally with the 40nm internal EPHY
which agressively disables its clocks for power savings leading to
incomplete resets of the UniMAC and many instabilities observed
over the years. The workaround of this commit is expected to put
an end to those problems.
Fixes: 1c1008c793 ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to show ranges of variables (--range and --vars option) in functions
which DIE has only ranges but no entry_pc attribute.
Without this fix:
# perf probe --range -V clear_tasks_mm_cpumask
Available variables at clear_tasks_mm_cpumask
@<clear_tasks_mm_cpumask+0>
(No matched variables)
With this fix:
# perf probe --range -V clear_tasks_mm_cpumask
Available variables at clear_tasks_mm_cpumask
@<clear_tasks_mm_cpumask+0>
[VAL] int cpu @<clear_tasks_mm_cpumask+[0-35,317-317,2052-2059]>
Committer testing:
Before:
[root@quaco ~]# perf probe --range -V clear_tasks_mm_cpumask
Available variables at clear_tasks_mm_cpumask
@<clear_tasks_mm_cpumask+0>
(No matched variables)
[root@quaco ~]#
After:
[root@quaco ~]# perf probe --range -V clear_tasks_mm_cpumask
Available variables at clear_tasks_mm_cpumask
@<clear_tasks_mm_cpumask+0>
[VAL] int cpu @<clear_tasks_mm_cpumask+[0-23,23-105,105-106,106-106,1843-1850,1850-1862]>
[root@quaco ~]#
Using it:
[root@quaco ~]# perf probe clear_tasks_mm_cpumask cpu
Added new event:
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask with cpu)
You can now use it in all perf tools, such as:
perf record -e probe:clear_tasks_mm_cpumask -aR sleep 1
[root@quaco ~]# perf probe -l
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask@kernel/cpu.c with cpu)
[root@quaco ~]#
[root@quaco ~]# perf trace -e probe:*cpumask
^C[root@quaco ~]#
Fixes: 349e8d2611 ("perf probe: Add --range option to show a variable's location range")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/157199323018.8075.8179744380479673672.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Since debuginfo__find_probe_point() uses dwarf_entrypc() for finding the
entry address of the function on which a probe is, it will fail when the
function DIE has only ranges attribute.
To fix this issue, use die_entrypc() instead of dwarf_entrypc().
Without this fix, perf probe -l shows incorrect offset:
# perf probe -l
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask+18446744071579263632@work/linux/linux/kernel/cpu.c)
probe:clear_tasks_mm_cpumask_1 (on clear_tasks_mm_cpumask+18446744071579263752@work/linux/linux/kernel/cpu.c)
With this:
# perf probe -l
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask@work/linux/linux/kernel/cpu.c)
probe:clear_tasks_mm_cpumask_1 (on clear_tasks_mm_cpumask:21@work/linux/linux/kernel/cpu.c)
Committer testing:
Before:
[root@quaco ~]# perf probe -l
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask+18446744071579765152@kernel/cpu.c)
[root@quaco ~]#
After:
[root@quaco ~]# perf probe -l
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask@kernel/cpu.c)
[root@quaco ~]#
Fixes: 1d46ea2a6a ("perf probe: Fix listing incorrect line number with inline function")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/157199321227.8075.14655572419136993015.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix perf probe to probe an inlne function which has no entry pc
or low pc but only has ranges attribute.
This seems very rare case, but I could find a few examples, as
same as probe_point_search_cb(), use die_entrypc() to get the
entry address in probe_point_inline_cb() too.
Without this patch:
# perf probe -D __amd_put_nb_event_constraints
Failed to get entry address of __amd_put_nb_event_constraints.
Probe point '__amd_put_nb_event_constraints' not found.
Error: Failed to add events.
With this patch:
# perf probe -D __amd_put_nb_event_constraints
p:probe/__amd_put_nb_event_constraints amd_put_event_constraints+43
Committer testing:
Before:
[root@quaco ~]# perf probe -D __amd_put_nb_event_constraints
Failed to get entry address of __amd_put_nb_event_constraints.
Probe point '__amd_put_nb_event_constraints' not found.
Error: Failed to add events.
[root@quaco ~]#
After:
[root@quaco ~]# perf probe -D __amd_put_nb_event_constraints
p:probe/__amd_put_nb_event_constraints _text+33789
[root@quaco ~]#
Fixes: 4ea42b1814 ("perf: Add perf probe subcommand, a kprobe-event setup helper")
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/157199320336.8075.16189530425277588587.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix 'perf probe' to probe a function which has no entry pc or low pc but
only has ranges attribute.
probe_point_search_cb() uses dwarf_entrypc() to get the probe address,
but that doesn't work for the function DIE which has only ranges
attribute. Use die_entrypc() instead.
Without this fix:
# perf probe -k ../build-x86_64/vmlinux -D clear_tasks_mm_cpumask:0
Probe point 'clear_tasks_mm_cpumask' not found.
Error: Failed to add events.
With this:
# perf probe -k ../build-x86_64/vmlinux -D clear_tasks_mm_cpumask:0
p:probe/clear_tasks_mm_cpumask clear_tasks_mm_cpumask+0
Committer testing:
Before:
[root@quaco ~]# perf probe clear_tasks_mm_cpumask:0
Probe point 'clear_tasks_mm_cpumask' not found.
Error: Failed to add events.
[root@quaco ~]#
After:
[root@quaco ~]# perf probe clear_tasks_mm_cpumask:0
Added new event:
probe:clear_tasks_mm_cpumask (on clear_tasks_mm_cpumask)
You can now use it in all perf tools, such as:
perf record -e probe:clear_tasks_mm_cpumask -aR sleep 1
[root@quaco ~]#
Using it with 'perf trace':
[root@quaco ~]# perf trace -e probe:clear_tasks_mm_cpumask
Doesn't seem to be used in x86_64:
$ find . -name "*.c" | xargs grep clear_tasks_mm_cpumask
./kernel/cpu.c: * clear_tasks_mm_cpumask - Safely clear tasks' mm_cpumask for a CPU
./kernel/cpu.c:void clear_tasks_mm_cpumask(int cpu)
./arch/xtensa/kernel/smp.c: clear_tasks_mm_cpumask(cpu);
./arch/csky/kernel/smp.c: clear_tasks_mm_cpumask(cpu);
./arch/sh/kernel/smp.c: clear_tasks_mm_cpumask(cpu);
./arch/arm/kernel/smp.c: clear_tasks_mm_cpumask(cpu);
./arch/powerpc/mm/nohash/mmu_context.c: clear_tasks_mm_cpumask(cpu);
$ find . -name "*.h" | xargs grep clear_tasks_mm_cpumask
./include/linux/cpu.h:void clear_tasks_mm_cpumask(int cpu);
$ find . -name "*.S" | xargs grep clear_tasks_mm_cpumask
$
Fixes: e1ecbbc3fa ("perf probe: Fix to handle optimized not-inlined functions")
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/157199319438.8075.4695576954550638618.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Since there are some DIE which has only ranges instead of the
combination of entrypc/highpc, address verification must use
dwarf_haspc() instead of dwarf_entrypc/dwarf_highpc.
Also, the ranges only DIE will have a partial code in different section
(e.g. unlikely code will be in text.unlikely as "FUNC.cold" symbol). In
that case, we can not use dwarf_entrypc() or die_entrypc(), because the
offset from original DIE can be a minus value.
Instead, this simply gets the symbol and offset from symtab.
Without this patch;
# perf probe -D clear_tasks_mm_cpumask:1
Failed to get entry address of clear_tasks_mm_cpumask
Error: Failed to add events.
And with this patch:
# perf probe -D clear_tasks_mm_cpumask:1
p:probe/clear_tasks_mm_cpumask clear_tasks_mm_cpumask+0
p:probe/clear_tasks_mm_cpumask_1 clear_tasks_mm_cpumask+5
p:probe/clear_tasks_mm_cpumask_2 clear_tasks_mm_cpumask+8
p:probe/clear_tasks_mm_cpumask_3 clear_tasks_mm_cpumask+16
p:probe/clear_tasks_mm_cpumask_4 clear_tasks_mm_cpumask+82
Committer testing:
I managed to reproduce the above:
[root@quaco ~]# perf probe -D clear_tasks_mm_cpumask:1
p:probe/clear_tasks_mm_cpumask _text+919968
p:probe/clear_tasks_mm_cpumask_1 _text+919973
p:probe/clear_tasks_mm_cpumask_2 _text+919976
[root@quaco ~]#
But then when trying to actually put the probe in place, it fails if I
use :0 as the offset:
[root@quaco ~]# perf probe -L clear_tasks_mm_cpumask | head -5
<clear_tasks_mm_cpumask@/usr/src/debug/kernel-5.2.fc30/linux-5.2.18-200.fc30.x86_64/kernel/cpu.c:0>
0 void clear_tasks_mm_cpumask(int cpu)
1 {
2 struct task_struct *p;
[root@quaco ~]# perf probe clear_tasks_mm_cpumask:0
Probe point 'clear_tasks_mm_cpumask' not found.
Error: Failed to add events.
[root@quaco
The next patch is needed to fix this case.
Fixes: 576b523721 ("perf probe: Fix probing symbols with optimization suffix")
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lore.kernel.org/lkml/157199318513.8075.10463906803299647907.stgit@devnote2
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
