Few ti-sysc related fixes for v5.5 merge window
Just few minor changes that can be merged when suitable, but would
be good to have these in v5.5-rc1 to remove dependencies between branches
for more changes later on in v5.6:
- Add quirk handling for AESS (Audio Engine Sub System)
- We want to drop the useless gptimer option for omap4 as there are local
timers
- A minor error path handling improvment for sysc_child_add_named_clock()
that will make further patching a bit easier
* tag 'omap-for-v5.5/ti-sysc-late-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: ti-sysc: Adjust exception handling in sysc_child_add_named_clock()
ARM: OMAP2+: Drop useless gptimer option for omap4
bus: ti-sysc: Add module enable quirk for audio AESS
Link: https://lore.kernel.org/r/pull-1574273726-31367@atomide.com
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull ARM SoC driver updates from Olof Johansson:
"Various driver updates for platforms:
- A larger set of work on Tegra 2/3 around memory controller and
regulator features, some fuse cleanups, etc..
- MMP platform drivers, in particular for USB PHY, and other smaller
additions.
- Samsung Exynos 5422 driver for DMC (dynamic memory configuration),
and ASV (adaptive voltage), allowing the platform to run at more
optimal operating points.
- Misc refactorings and support for RZ/G2N and R8A774B1 from Renesas
- Clock/reset control driver for TI/OMAP
- Meson-A1 reset controller support
- Qualcomm sdm845 and sda845 SoC IDs for socinfo"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (150 commits)
firmware: arm_scmi: Fix doorbell ring logic for !CONFIG_64BIT
soc: fsl: add RCPM driver
dt-bindings: fsl: rcpm: Add 'little-endian' and update Chassis definition
memory: tegra: Consolidate registers definition into common header
memory: tegra: Ensure timing control debug features are disabled
memory: tegra: Introduce Tegra30 EMC driver
memory: tegra: Do not handle error from wait_for_completion_timeout()
memory: tegra: Increase handshake timeout on Tegra20
memory: tegra: Print a brief info message about EMC timings
memory: tegra: Pre-configure debug register on Tegra20
memory: tegra: Include io.h instead of iopoll.h
memory: tegra: Adapt for Tegra20 clock driver changes
memory: tegra: Don't set EMC rate to maximum on probe for Tegra20
memory: tegra: Add gr2d and gr3d to DRM IOMMU group
memory: tegra: Set DMA mask based on supported address bits
soc: at91: Add Atmel SFR SN (Serial Number) support
memory: atmel-ebi: switch to SPDX license identifiers
memory: atmel-ebi: move NUM_CS definition inside EBI driver
soc: mediatek: Refactor bus protection control
soc: mediatek: Refactor sram control
...
Pull chrome platform changes from Benson Leung:
"CrOS EC / MFD / IIO:
- Contains tag-ib-chrome-mfd-iio-input-5.5, which is the first part
of a series from Gwendal to refactor sensor code between MFD, CrOS
EC, iio and input in order to add a new sensorhub driver and FIFO
processing
Wilco EC:
- Add support for Dell's USB PowerShare policy control, keyboard
backlight LED driver, and a new test_event file.
- Fixes use after free in wilco_ec's telemetry driver.
Misc:
- bugfix in cros_usbpd_logger (missing destroy workqueue)"
* tag 'tag-chrome-platform-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: wilco_ec: fix use after free issue
platform/chrome: cros_ec: Add Kconfig default for cros-ec-sensorhub
Revert "Input: cros_ec_keyb: mask out extra flags in event_type"
Revert "Input: cros_ec_keyb - add back missing mask for event_type"
platform/chrome: cros_ec: handle MKBP more events flag
platform/chrome: cros_ec: Do not attempt to register a non-positive IRQ number
platform/chrome: cros-ec: Record event timestamp in the hard irq
mfd / platform / iio: cros_ec: Register sensor through sensorhub
iio / platform: cros_ec: Add cros-ec-sensorhub driver
mfd / platform: cros_ec: Add sensor_count and make check_features public
platform/chrome: cros_ec: Put docs with the code
platform/chrome: cros_usbpd_logger: add missed destroy_workqueue in remove
platform/chrome: cros_ec: Fix Kconfig indentation
platform/chrome: wilco_ec: Add keyboard backlight LED support
platform/chrome: wilco_ec: Add charging config driver
platform/chrome: wilco_ec: Add Dell's USB PowerShare Policy control
platform/chrome: wilco_ec: Add debugfs test_event file
Pull input updates from Dmitry Torokhov:
- updates to Ilitech driver to support ILI2117
- face lift of st1232 driver to support MT-B protocol
- a new driver for i.MX system controller keys
- mpr121 driver now supports polling mode
- various input drivers have been switched away from input_polled_dev
to use polled mode of regular input devices
- other assorted cleanups and fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (70 commits)
Input: synaptics-rmi4 - fix various V4L2 compliance problems in F54
Input: synaptics - switch another X1 Carbon 6 to RMI/SMbus
Input: fix Kconfig indentation
Input: imx_sc_key - correct SCU message structure to avoid stack corruption
Input: ili210x - optionally show calibrate sysfs attribute
Input: ili210x - add resolution to chip operations structure
Input: ili210x - do not retrieve/print chip firmware version
Input: mms114 - use device_get_match_data
Input: ili210x - remove unneeded suspend and resume handlers
Input: ili210x - do not unconditionally mark touchscreen as wakeup source
Input: ili210x - define and use chip operations structure
Input: ili210x - do not set parent device explicitly
Input: ili210x - handle errors from input_mt_init_slots()
Input: ili210x - switch to using threaded IRQ
Input: ili210x - add ILI2117 support
dt-bindings: input: touchscreen: ad7879: generic node names in example
Input: ar1021 - fix typo in preprocessor macro name
Input: synaptics-rmi4 - simplify data read in rmi_f54_work
Input: kxtj9 - switch to using polled mode of input devices
Input: kxtj9 - switch to using managed resources
...
Pull i2c updates from Wolfram Sang:
"I2C has mostly driver updates this time.
The few noteworthy changes are: the core has now support for analog
and digital filters with at91 being the first user, a core addition to
replace the NULL returning i2c_new_probed_device() with an ERR_PTR
variant, and the pxa driver has finally being moved to use the generic
I2C slave interface. We have quite a significant number of reviews per
patch this time, so thank you to all involved!"
* 'i2c/for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (37 commits)
video: fbdev: matrox: convert to i2c_new_scanned_device
i2c: icy: convert to i2c_new_scanned_device
i2c: replace i2c_new_probed_device with an ERR_PTR variant
i2c: Fix Kconfig indentation
i2c: smbus: Don't filter out duplicate alerts
i2c: i801: Correct Intel Jasper Lake SOC naming
i2c: i2c-stm32f7: fix 10-bits check in slave free id search loop
i2c: iproc: Add i2c repeated start capability
i2c: remove helpers for ref-counting clients
i2c: tegra: Use dma_request_chan() directly for channel request
i2c: sh_mobile: Use dma_request_chan() directly for channel request
i2c: qup: Use dma_request_chan() directly for channel request
i2c: at91: Use dma_request_chan() directly for channel request
i2c: rcar: Remove superfluous call to clk_get_rate()
i2c: pxa: remove unused i2c-slave APIs
i2c: pxa: migrate to new i2c_slave APIs
i2c: cros-ec-tunnel: Make the device acpi compatible
i2c: stm32f7: report dma error during probe
i2c: icy: no need to populate address for scanned device
i2c: xiic: Fix kerneldoc warnings
...
Pull backlight updates from Lee Jones:
"New Functionality:
- Add support for an enable GPIO; lm3630a_bl
- Add support for short circuit handling; qcom-wled
- Add support for automatic string detection; qcom-wled
Fix-ups:
- Update Device Tree bindings; lm3630a-backlight, led-backlight,
qcom-wled
- Constify; ipaq_micro_bl
- Optimise for CPU cycles; pwm_bl
- Coding style fix-ups; pwm_bl
- Trivial fix-ups (white space, comments, renaming); pwm_bl,
gpio_backlight, qcom-wled
- Kconfig dependency hacking; LCD_HP700
- Rename, refactor and add peripherals; pm8941-wled => qcom-wled
- Make use of GPIO look-up tables; tosa_bl, tosa_lcd
- Remove superfluous code; gpio_backlight
- Adapt GPIO direction handling; gpio_backlight
- Remove legacy use of platform data; gpio_backlight
Bug Fixes:
- Provide modules aliases; lm3630a_bl"
* tag 'backlight-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight: (32 commits)
backlight: qcom-wled: Fix spelling mistake "trigged" -> "triggered"
backlight: gpio: Pull gpio_backlight_initial_power_state() into probe
backlight: gpio: Use a helper variable for &pdev->dev
backlight: gpio: Remove unused fields from platform data
sh: ecovec24: don't set unused fields in platform data
backlight: gpio: Simplify the platform data handling
sh: ecovec24: add additional properties to the backlight device
backlight: gpio: Explicitly set the direction of the GPIO
backlight: gpio: Remove stray newline
backlight: gpio: Remove unneeded include
video: backlight: tosa: Use GPIO lookup table
backlight: qcom-wled: Add auto string detection logic
backlight: qcom-wled: Add support for short circuit handling
backlight: qcom-wled: Add support for WLED4 peripheral
backlight: qcom-wled: Restructure the driver for WLED3
backlight: qcom-wled: Rename PM8941* to WLED3
backlight: qcom-wled: Add new properties for PMI8998
backlight: qcom-wled: Restructure the qcom-wled bindings
backlight: qcom-wled: Rename pm8941-wled.c to qcom-wled.c
dt-bindings: backlight: lm3630a: Fix missing include
...
Pull staging / iio updates from Greg KH:
"Here is the big staging and iio set of patches for the 5.5-rc1
release.
It's the usual huge collection of cleanup patches all over the
drivers/staging/ area, along with a new staging driver, and a bunch of
new IIO drivers as well.
Full details are in the shortlog, but all of these have been in
linux-next for a long time with no reported issues"
* tag 'staging-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (548 commits)
staging: vchiq: Have vchiq_dump_* functions return an error code
staging: vchiq: Refactor indentation in vchiq_dump_* functions
staging: fwserial: Fix Kconfig indentation (seven spaces)
staging: vchiq_dump: Replace min with min_t
staging: vchiq: Fix block comment format in vchiq_dump()
staging: octeon: indent with tabs instead of spaces
staging: comedi: usbduxfast: usbduxfast_ai_cmdtest rounding error
staging: most: core: remove sysfs attr remove_link
staging: vc04: Fix Kconfig indentation
staging: pi433: Fix Kconfig indentation
staging: nvec: Fix Kconfig indentation
staging: most: Fix Kconfig indentation
staging: fwserial: Fix Kconfig indentation
staging: fbtft: Fix Kconfig indentation
fbtft: Drop OF dependency
fbtft: Make use of device property API
fbtft: Drop useless #ifdef CONFIG_OF and dead code
fbtft: Describe function parameters in kernel-doc
fbtft: Make sure string is NULL terminated
staging: rtl8723bs: remove set but not used variable 'change', 'pos'
...
Pull MMC updates from Ulf Hansson:
"These are the updates for MMC and MEMSTICK for v5.5.
Note that this also contains quite some additional changes reaching
beyond both the MMC and MEMSTICK subsystems. This is primarily because
of fixing an old regression for a WiFi driver based on the SDIO
interface on an OMAP openpandora board
MMC core:
- Add CMD13 polling for MMC IOCTLS with R1B response.
- Add common DT properties for clk-phase-delays for various speed
modes.
- Fix size overflow for mmc gp-partitions.
- Re-work HW reset for SDIO cards, which also includes a re-work for
Marvell's WiFi mwifiex SDIO func driver.
MMC host:
- jz4740: Add support for X1000 and JZ4760.
- jz4740: Add support for 8-bit bus and for low power mode.
- mmci: Add support for HW busy timeout for the stm32_sdmmc variant.
- owl-mmc: Add driver for Actions Semi Owl SoCs SD/MMC controller.
- renesas_sdhi: Add support for r8a774b1.
- sdhci_am654: Add support for Command Queuing Engine for J721E.
- sdhci-milbeaut: Add driver for the Milbeaut SD controller.
- sdhci-of-arasan: Add support for ZynqMP tap-delays.
- sdhci-of-arasan: Add support for clk-phase-delays for SD cards.
- sdhci-of-arasan: Add support for Intel LGM SDXC.
- sdhci-of-aspeed: Allow inversion of the internal card detect
signal.
- sdhci-of-esdhc: Fixup workaround for erratum A-008171 for tunings.
- sdhci-of-at91: Improve support for calibration.
- sdhci-pci: Add support for Intel JSL.
- sdhci-pci: Add quirk for AMD SDHC Device 0x7906.
- tmio: Enable support for erase/discard/trim requests.
MMC/OMAP/pandora/wl1251:
The TI wl1251 WiFi driver for SDIO on the OMAP openpandora board has
been broken since v4.7. To fix the problems, changes have been made
cross subsystems, but also to OMAP2 machine code and to openpandora
DTS files, as summarized below. Relevant changes have been tagged for
stable.
- mmc/wl1251: Re-introduce lost SDIO quirks and vendor-id for wl1251
- omap/omap_hsmmc: Remove redundant platform config for openpandora
- omap_hsmmc: Initialize non-std SDIO card for wl1251 for pandora
- omap/dts/pandora: Specify wl1251 through a child node of mmc3
- wl1251: Add devicetree support for TI wl1251 SDIO"
* tag 'mmc-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (73 commits)
dt-bindings: mmc: Correct the type of the clk phase properties
Revert "mmc: tmio: remove workaround for NON_REMOVABLE"
memstick: Fix Kconfig indentation
mmc: sdhci-of-arasan: Add support for ZynqMP Platform Tap Delays Setup
dt-bindings: mmc: arasan: Document 'xlnx,zynqmp-8.9a' controller
firmware: xilinx: Add SDIO Tap Delay nodes
mmc: sdhci-of-arasan: Add support to set clock phase delays for SD
dt-bindings: mmc: Add optional generic properties for mmc
mmc: sdhci-of-arasan: Add sampling clock for a phy to use
dt-bindings: mmc: arasan: Update Documentation for the input clock
mmc: sdhci-of-arasan: Separate out clk related data to another structure
mmc: sdhci: Fix grammar in warning message
mmc: sdhci-of-aspeed: add inversion signal presence
mmc: sdhci-of-aspeed: enable CONFIG_MMC_SDHCI_IO_ACCESSORS
mmc: sdhci_am654: Add Support for Command Queuing Engine to J721E
mmc: core: Fix size overflow for mmc partitions
mmc: tmio: Add MMC_CAP_ERASE to allow erase/discard/trim requests
net: wireless: ti: remove local VENDOR_ID and DEVICE_ID definitions
net: wireless: ti: wl1251 use new SDIO_VENDOR_ID_TI_WL1251 definition
mmc: core: fix wl1251 sdio quirks
...
Pull sound updates from Takashi Iwai:
"There have been some significant changes in the core side, both for
ALSA and ASoC, while lots of development have been seen in SOF, as
well as many small fixes/improvements for ASoC codecs and platforms.
Below is a highlight in this cycle:
Core:
- The unification of PCM vmalloc buffer allocation helpers into the
standard API
- Clean up of the default PCM mmap handling for vmalloc & SG-buffer
- Fix potential races at ALSA timer open
- A few new PCM API extensions; just preliminary core changes, the
actual changes in drivers will be merged in 5.6
- Continued ASoC componentization works; now almost everything is a
common ASoC component object. A lot of refactoring and
simplification have been done along with it.
ASoC:
- Many fixes to the Sound Open Firmware (SOF) code
- Wake on voice support for Chromebooks
- SPI support and trigger word detection for RT5677
- New drivers for Analog Devices ADAU7118, Intel Cannonlake systems
with RT1011 and RT5682, Texas Instruments TAS2562 and TAS2770
HD-audio:
- Improved Intel DSP configuration / probe code for SOF
- Plumbing the legacy HD-audio driver with Intel SOF HDMI
- DP-MST support for Nvidia HDMI codecs
- Realtek quirks cleanups and new additions as usual
Others:
- Lots of refactoring and cleanups for FireWire; period-size sharing,
h/w IRQ interval configuration, clock recovery improvements, etc
- USB-audio: Scarlett mixer quirks
- Cleanups of PCM calls in various drivers (including media and USB)
to adapt the core API changes"
* tag 'sound-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (497 commits)
ALSA: usb-audio: Fix Focusrite Scarlett 6i6 gen1 - input handling
ALSA: hda/realtek - Enable internal speaker of ASUS UX431FLC
ALSA: aloop: Fix dependency on timer API
ASoC: DMI long name - avoid to add board name if matches with product name
ASoC: improve the DMI long card code in asoc-core
ASoC: rsnd: fix DALIGN register for SSIU
ALSA: aloop: Avoid unexpected timer event callback tasklets
ALSA: aloop: Remove redundant locking in timer open function
ASoC: component: Add sync_stop PCM ops
ASoC: pcm: Make ioctl ops optional
ALSA: hda/hdmi - Clear codec->relaxed_resume flag at unbinding
ALSA: hda - Disable audio component for legacy Nvidia HDMI codecs
ALSA: cs4236: fix error return comparison of an unsigned integer
ALSA: usb-audio: Fix NULL dereference at parsing BADD
ALSA: usb-audio: Fix Scarlett 6i6 Gen 2 port data
ALSA: hda/realtek - Enable the headset-mic on a Xiaomi's laptop
ALSA: hda/realtek - Move some alc236 pintbls to fallback table
ALSA: hda/realtek - Move some alc256 pintbls to fallback table
ALSA: docs: Update about the new PCM sync_stop ops
ALSA: pcm: Add card sync_irq field
...
Pull spi updates from Mark Brown:
"Lots of stuff going on in the core for SPI this time around, the two
big changes both being around time in different forms:
- A rework of delay times from Alexandru Ardelean which makes the
ways in which they are specified more consistent between drivers so
that what's available to clients is less dependent on the hardware
implementation.
- Support for PTP timestamping of transfers from Vladimir Oltean,
useful for use with precision clocks with SPI control interfaces.
- Big cleanups for the Atmel, PXA2xx and Zynq QSPI drivers"
* tag 'spi-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (119 commits)
dt-bindings: spi: Convert stm32 QSPI bindings to json-schema
spi: pic32: Retire dma_request_slave_channel_compat()
spi: Fix Kconfig indentation
spi: mediatek: add SPI_CS_HIGH support
spi: st-ssc4: add missed pm_runtime_disable
spi: tegra20-slink: add missed clk_unprepare
spi: tegra20-slink: Use dma_request_chan() directly for channel request
spi: tegra114: Use dma_request_chan() directly for channel request
spi: s3c64xx: Use dma_request_chan() directly for channel request
spi: qup: Use dma_request_chan() directly for channel request
spi: pl022: Use dma_request_chan() directly for channel request
spi: imx: Use dma_request_chan() directly for channel request
spi: fsl-lpspi: Use dma_request_chan() directly for channel request
spi: atmel: Use dma_request_chan() directly for channel request
spi: at91-usart: Use dma_request_chan() directly for channel request
spi: fsl-cpm: Correct the free:ing
spi: Fix regression to return zero on success instead of positive value
spi: pxa2xx: Add missed security checks
spi: nxp-fspi: Use devm API to fix missed unregistration of controller
spi: omap2-mcspi: Remove redundant checks
...
Pull MTD updates from Miquel Raynal:
"MTD core:
- drop inactive maintainers, update the repositories and add IRC
channel
- debugfs functions improvements
- initialize more structure parameters
- misc fixes reported by robots
MTD devices:
- spear_smi: Fixed Write Burst mode
- new Intel IXP4xx flash probing hook
Raw NAND core:
- useless extra checks dropped
- update the detection of the bad block markers position
Raw NAND controller drivers:
- Cadence: new driver
- Brcmnand: support for flash-dma v0 + fixes
- Denali: drop support for the legacy controller/chip DT representation
- superfluous dev_err() calls removed
SPI NOR core changes:
- introduce 'struct spi_nor_controller_ops'
- clean the Register Operations methods
- use dev_dbg insted of dev_err for low level info
- fix retlen handling in sst_write()
- fix silent truncations in spi_nor_read and spi_nor_read_raw()
- fix the clearing of QE bit on lock()/unlock()
- rework the disabling of the block write protection
- rework the Quad Enable methods
- make sure nor->spimem and nor->controller_ops are mutually exclusive
- set default Quad Enable method for ISSI flashes
- add support for few flashes
SPI NOR controller drivers changes:
- intel-spi:
- support chips without software sequencer
- add support for Intel Cannon Lake and Intel Comet Lake-H flashes
CFI core changes:
- code cleanups related useless initializers and coding style issues
- fix for a possible double free problem in cfi_cmdset_0002
- improved HyperFlash error reporting and handling in cfi_cmdset_0002 core"
* tag 'mtd/for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (73 commits)
mtd: devices: fix mchp23k256 read and write
mtd: no need to check return value of debugfs_create functions
mtd: spi-nor: Set default Quad Enable method for ISSI flashes
mtd: spi-nor: Add support for is25wp256
mtd: spi-nor: Add support for w25q256jw
mtd: spi-nor: Move condition to avoid a NULL check
mtd: spi-nor: Make sure nor->spimem and nor->controller_ops are mutually exclusive
mtd: spi-nor: Rename Quad Enable methods
mtd: spi-nor: Merge spansion Quad Enable methods
mtd: spi-nor: Rename CR_QUAD_EN_SPAN to SR2_QUAD_EN_BIT1
mtd: spi-nor: Extend the SR Read Back test
mtd: spi-nor: Rework the disabling of block write protection
mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()
mtd: cfi_cmdset_0002: fix delayed error detection on HyperFlash
mtd: cfi_cmdset_0002: only check errors when ready in cfi_check_err_status()
mtd: cfi_cmdset_0002: don't free cfi->cfiq in error path of cfi_amdstd_setup()
mtd: cfi_cmdset_*: kill useless 'ret' variable initializers
mtd: cfi_util: use DIV_ROUND_UP() in cfi_udelay()
mtd: spi-nor: Print debug message when the read back test fails
mtd: spi-nor: Check all the bits written, not just the BP ones
...
The ChromeOS EC has support for signaling to the host that a single IRQ
can serve multiple MKBP (Matrix KeyBoard Protocol) events.
Doing this serves an optimization purpose, as it minimizes the number of
round-trips into the interrupt handling machinery, and it proves
beneficial to sensor timestamping as it keeps the desired synchronization
of event times between the two processors.
This patch adds kernel support for this EC feature, allowing the ec_irq
to loop until all events have been served.
Signed-off-by: Enrico Granata <egranata@chromium.org>
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
To improve sensor timestamp precision, given EC and AP are in different
time domains, the AP needs to try to record the exact moment an event
was signalled to the AP by the EC as soon as possible after it happens.
First thing in the hard irq is the best place for this.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Remove the duplicated code in MFD, since MFD just registers cros-ec-sensorhub
if at least one sensor is present.
Change IIO cros-ec driver to get the pointer to the cros-ec-dev through
cros-ec-sensorhub.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Similar to HID sensor stack, the new driver sits between cros-ec-dev
and the IIO device drivers:
The EC based IIO device topology would be:
iio:device1 ->
...0/0000:00:1f.0/PNP0C09:00/GOOG0004:00/cros-ec-dev.6.auto/
cros-ec-sensorhub.7.auto/
cros-ec-accel.15.auto/
iio:device1
It will be expanded to control EC sensor FIFO.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
[Fix "unknown type name 'uint32_t'" type errors]
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Add a new function to return the number of MEMS sensors available in a
ChromeOS Embedded Controller. It uses MOTIONSENSE_CMD_DUMP if available
or a specific memory map ACPI registers to find out.
Also, make check_features public as it can be useful for other drivers
to know what the Embedded Controller supports.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
To avoid doc rot, put function documentations with code, not header.
Use kernel-doc style comments for exported functions.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
The EC is in charge of controlling the keyboard backlight on
the Wilco platform. We expose a standard LED class device
named platform::kbd_backlight.
Since the EC will never change the backlight level of its own accord,
we don't need to implement a brightness_get() method.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Signed-off-by: Daniel Campello <campello@chromium.org>
Reviewed-by: Daniel Campello <campello@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Add a device to control the charging algorithm used on Wilco devices,
which will be picked up by the drivers/power/supply/wilco-charger.c
driver. See Documentation/ABI/testing/sysfs-class-power-wilco for the
userspace interface and other info.
Signed-off-by: Nick Crews <ncrews@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Now as we have removed the last user (pandora_wl1251_init_card)
of this callback, we can remove it from the hsmmc code.
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We must set the autogating bit on enable for AESS (Audio Engine SubSystem)
when probed with ti-sysc interconnect target module driver. Otherwise it
won't idle properly.
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the i2c-pxa driver migrated to the standard i2c-slave
APIs, the custom APIs and structures are no longer needed
or used. Remove them.
Signed-off-by: Patrick Williams <alpawi@amazon.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add the possibility to enable/disable wakeup source through
st_sensors_platform_data and not only through device tree
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Illegal memory will be touch if SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3
(41) exceed the size of structure sdma_script_start_addrs(40),
thus cause memory corrupt such as slob block header so that kernel
trap into while() loop forever in slob_free(). Please refer to below
code piece in imx-sdma.c:
for (i = 0; i < sdma->script_number; i++)
if (addr_arr[i] > 0)
saddr_arr[i] = addr_arr[i]; /* memory corrupt here */
That issue was brought by commit a572460be9 ("dmaengine: imx-sdma: Add
support for version 3 firmware") because SDMA_SCRIPT_ADDRS_ARRAY_SIZE_V3
(38->41 3 scripts added) not align with script number added in
sdma_script_start_addrs(2 scripts).
Fixes: a572460be9 ("dmaengine: imx-sdma: Add support for version 3 firmware")
Cc: stable@vger.kernel
Link: https://www.spinics.net/lists/arm-kernel/msg754895.html
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reported-by: Jurgen Lambrecht <J.Lambrecht@TELEVIC.com>
Link: https://lore.kernel.org/r/1569347584-3478-1-git-send-email-yibin.gong@nxp.com
[vkoul: update the patch title]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
All the defined symbols from linux/platform_data/pixcir_i2c_ts.h
are only used by the pixcir_i2c_ts driver, so move all the definitions
locally and get rid of the pixcir_i2c_ts.h file.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
TI SoCs hardware reset signals require the parent clockdomain to be
in force wakeup mode while de-asserting the reset, otherwise it may
never complete. To support this, add pdata hooks to control the
clockdomain directly.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Pull thermal SoC updates from Eduardo Valentin:
"This is a really small pull in the midst of a lot of pending patches.
We are in the middle of restructuring how we are maintaining the
thermal subsystem, as per discussion in our last LPC. For now, I am
sending just some changes that were pending in my tree. Looking
forward to get a more streamlined process in the next merge window"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: db8500: Rewrite to be a pure OF sensor
thermal: db8500: Use dev helper variable
thermal: db8500: Finalize device tree conversion
thermal: thermal_mmio: remove some dead code
Pull networking fixes from David Miller:
1) Sanity check URB networking device parameters to avoid divide by
zero, from Oliver Neukum.
2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6
don't work properly. Longer term this needs a better fix tho. From
Vijay Khemka.
3) Small fixes to selftests (use ping when ping6 is not present, etc.)
from David Ahern.
4) Bring back rt_uses_gateway member of struct rtable, it's semantics
were not well understood and trying to remove it broke things. From
David Ahern.
5) Move usbnet snaity checking, ignore endpoints with invalid
wMaxPacketSize. From Bjørn Mork.
6) Missing Kconfig deps for sja1105 driver, from Mao Wenan.
7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel,
Alex Vesker, and Yevgeny Kliteynik
8) Missing CAP_NET_RAW checks in various places, from Ori Nimron.
9) Fix crash when removing sch_cbs entry while offloading is enabled,
from Vinicius Costa Gomes.
10) Signedness bug fixes, generally in looking at the result given by
of_get_phy_mode() and friends. From Dan Crapenter.
11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet.
12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern.
13) Fix quantization code in tcp_bbr, from Kevin Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits)
net: tap: clean up an indentation issue
nfp: abm: fix memory leak in nfp_abm_u32_knode_replace
tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state
sk_buff: drop all skb extensions on free and skb scrubbing
tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth
mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions
Documentation: Clarify trap's description
mlxsw: spectrum: Clear VLAN filters during port initialization
net: ena: clean up indentation issue
NFC: st95hf: clean up indentation issue
net: phy: micrel: add Asym Pause workaround for KSZ9021
net: socionext: ave: Avoid using netdev_err() before calling register_netdev()
ptp: correctly disable flags on old ioctls
lib: dimlib: fix help text typos
net: dsa: microchip: Always set regmap stride to 1
nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs
nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs
net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N
vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled
net: sched: sch_sfb: don't call qdisc_put() while holding tree lock
...
At some point there was an attempt to convert the DB8500
thermal sensor to device tree: a probe path was added
and the device tree was augmented for the Snowball board.
The switchover was never completed: instead the thermal
devices came from from the PRCMU MFD device and the probe
on the Snowball was confused as another set of configuration
appeared from the device tree.
Move over to a device-tree only approach, as we fixed up
the device trees.
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
Pull ARM SoC late updates from Arnd Bergmann:
"This is some material that we picked up into our tree late or that had
complex inter-depondencies. The fact that there are these
interdependencies tends to meant that these are often actually the
most interesting new additions:
- The new Aspeed AST2600 baseboard management controller is added,
this is a Cortex-A7 based follow-up to the ARM11 based AST2500 and
had some dependencies on other device drivers.
- After many years, support for the MMP2 based OLPC XO-1.75 finally
makes it into the kernel.
- The Armada 3720 based Turris Mox open source router platform is a
late addition and it follows some preparatory work across multiple
branches.
- The OMAP2+ platform had some large-scale cleanup involving driver
changes and DT changes, here we finish it off, dropping a lot of
the now-unused platform data.
- The TI K3 platform that got added for 5.3 gains a lot more support
for individual bits on the SoC, this part just came late for the
merge window"
[ This pull request itself wasn't actually sent late at all by Arnd, but
I waited on the branches that it used to be pulled first, so it ends
up being merged much later than the other ARM SoC pull requests this
merge window - Linus ]
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (57 commits)
ARM: dts: dir685: Drop spi-cpol from the display
ARM: dts: aspeed: Add AST2600 pinmux nodes
ARM: dts: aspeed: Add AST2600 and EVB
ARM: exynos: Enable support for ARM architected timers
ARM: samsung: Fix system restart on S3C6410
ARM: dts: mmp2: add OLPC XO 1.75 machine
ARM: dts: mmp2: rename the USB PHY node
ARM: dts: mmp2: specify reg-shift for the UARTs
ARM: dts: mmp2: add camera interfaces
ARM: dts: mmp2: fix the SPI nodes
ARM: dts: mmp2: trivial whitespace fix
arm64: dts: marvell: add DTS for Turris Mox
dt-bindings: marvell: document Turris Mox compatible
arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
arm64: dts: ti: k3-j721e-main: Fix gic-its node unit-address
arm64: dts: ti: k3-am65-main: Fix gic-its node unit-address
arm64: dts: ti: k3-j721e-main: Add hwspinlock node
arm64: dts: ti: k3-am65-main: Add hwspinlock node
arm64: dts: k3-j721e: Add gpio-keys on common processor board
dt-bindings: pinctrl: k3: Introduce pinmux definitions for J721E
...
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
Pull chrome platform updates from Benson Leung:
"CrOS EC / MFD Migration:
- Move cros_ec core driver from mfd into chrome platform.
Wilco EC:
- Add batt_ppid_info command to Wilco telemetry driver.
CrOS EC:
- cros_ec_rpmsg : Add support to inform EC of suspend/resume status
- cros_ec_rpmsg : Fix race condition on probe failed
- cros_ec_chardev : Add a poll handler to receive MKBP events
Misc:
- bugfixes in cros_usbpd_logger and cros_ec_ishtp"
* tag 'tag-chrome-platform-for-v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux:
platform/chrome: cros_usbpd_logger: null check create_singlethread_workqueue
platform/chrome: cros_ec_chardev: Add a poll handler to receive MKBP events
platform/chrome: cros_ec_rpmsg: Fix race with host command when probe failed
platform/chrome: chromeos_tbmc: Report wake events
mfd: cros_ec: Use mfd_add_hotplug_devices() helper
mfd: cros_ec: Add convenience struct to define autodetectable CrOS EC subdevices
mfd: cros_ec: Add convenience struct to define dedicated CrOS EC MCUs
mfd: cros_ec: Use kzalloc and cros_ec_cmd_xfer_status helper
mfd / platform: cros_ec: Reorganize platform and mfd includes
mfd / platform: cros_ec: Rename config to a better name
mfd: cros_ec: Switch to use the new cros-ec-chardev driver
mfd / platform: cros_ec: Miscellaneous character device to talk with the EC
mfd / platform: cros_ec: Move cros-ec core driver out from MFD
mfd / platform: cros_ec: Handle chained ECs as platform devices
platform/chrome: cros_ec_rpmsg: Add host command AP sleep state support
platform/chrome: chromeos_laptop: drop checks of NULL-safe functions
platform/chrome: wilco_ec: Add batt_ppid_info command to telemetry driver
Pull input updates from Dmitry Torokhov:
- input core allows hardware drivers to specify a [more precise]
timestamp (normally taken in top half) to better track velocity of
contacts
- input_dev instances now support "polling" mode so that drivers could
use the same object for polled and interrupt-driven operation. The
plan is to convert existing drivers and retire input_polled_dev API
- a new driver for the FlySky FS-iA6B RC receiver
- a refresh of BU21013 touchpad driver
- w90x900 keyboard and touchpad drivers are removed as the platform is
gone
- assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (45 commits)
Input: sidewinder - make array seq static const, makes object smaller
Input: reset device timestamp on sync
Input: bu21013_ts - switch to using standard touchscreen properties
Input: bu21013_ts - switch to using MT-B (slotted) protocol
Input: bu21013_ts - fix suspend when wake source
Input: bu21013_ts - use interrupt from I2C client
Input: bu21013_ts - remove support for platform data
Input: bu21013_ts - convert to using managed resources
Input: bu21013_ts - remove useless comments
Input: bu21013_ts - annotate supend/resume methods as __maybe_unused
Input: bu21013_ts - rename some variables
Input: bu21013_ts - convert to use GPIO descriptors
ARM: ux500: improve BU21013 touchpad bindings
Input: i8042 - enable wakeup on a stable struct device
Input: soc_button_array - use platform_device_register_resndata()
Input: psmouse - drop all unneeded functions from mouse headers
Input: add support for polling to input devices
Input: wacom_w8001 - allocate additional space for 'phys'
Input: cros_ec_keyb - add back missing mask for event_type
Input: remove dev_err() usage after platform_get_irq()
...
Pull networking updates from David Miller:
1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski.
2) Use bio_vec in the networking instead of custom skb_frag_t, from
Matthew Wilcox.
3) Make use of xmit_more in r8169 driver, from Heiner Kallweit.
4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen.
5) Support all variants of 5750X bnxt_en chips, from Michael Chan.
6) More RTNL avoidance work in the core and mlx5 driver, from Vlad
Buslov.
7) Add TCP syn cookies bpf helper, from Petar Penkov.
8) Add 'nettest' to selftests and use it, from David Ahern.
9) Add extack support to drop_monitor, add packet alert mode and
support for HW drops, from Ido Schimmel.
10) Add VLAN offload to stmmac, from Jose Abreu.
11) Lots of devm_platform_ioremap_resource() conversions, from
YueHaibing.
12) Add IONIC driver, from Shannon Nelson.
13) Several kTLS cleanups, from Jakub Kicinski.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits)
mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer
mlxsw: spectrum: Register CPU port with devlink
mlxsw: spectrum_buffers: Prevent changing CPU port's configuration
net: ena: fix incorrect update of intr_delay_resolution
net: ena: fix retrieval of nonadaptive interrupt moderation intervals
net: ena: fix update of interrupt moderation register
net: ena: remove all old adaptive rx interrupt moderation code from ena_com
net: ena: remove ena_restore_ethtool_params() and relevant fields
net: ena: remove old adaptive interrupt moderation code from ena_netdev
net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*()
net: ena: enable the interrupt_moderation in driver_supported_features
net: ena: reimplement set/get_coalesce()
net: ena: switch to dim algorithm for rx adaptive interrupt moderation
net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it
net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable
ethtool: implement Energy Detect Powerdown support via phy-tunable
xen-netfront: do not assume sk_buff_head list is empty in error handling
s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb”
net: ena: don't wake up tx queue when down
drop_monitor: Better sanitize notified packets
...
