commit f23643306430f86e2f413ee2b986e0773e79da31 upstream.
Some usb hubs will negotiate DisplayPort Alt mode with the device
but will then negotiate a data role swap after entering the alt
mode. The data role swap causes the device to unregister all alt
modes, however the usb hub will still send Attention messages
even after failing to reregister the Alt Mode. type_altmode_attention
currently does not verify whether or not a device's altmode partner
exists, which results in a NULL pointer error when dereferencing
the typec_altmode and typec_altmode_ops belonging to the altmode
partner.
Verify the presence of a device's altmode partner before sending
the Attention message to the Alt Mode driver.
Fixes: 8a37d87d72 ("usb: typec: Bus type for alternate modes")
Cc: stable@vger.kernel.org
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20230814180559.923475-1-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ce7d0008c2356626f69f37ef1afce8fbc83fe142 ]
Some UDCs may have constraints on how many high bandwidth endpoints it can
support in a certain configuration. This API allows for the composite
driver to pass down the total number of endpoints to the UDC so it can verify
it has the required resources to support the configuration.
Signed-off-by: Wesley Cheng <wcheng@codeaurora.org>
Link: https://lore.kernel.org/r/1625908395-5498-2-git-send-email-wcheng@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: dbe678f6192f ("usb: cdns3: fix NCM gadget RX speed 20x slow than expection at iMX8QM")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit edd60d24bd858cef165274e4cd6cab43bdc58d15 ]
Currently if we bootup a device without cable connected, then
usb-conn-gpio won't call set_role() since last_role is same as
current role. This happens because during probe last_role gets
initialised to zero.
To avoid this, added a new constant in enum usb_role, last_role
is set to USB_ROLE_UNKNOWN before performing initial detection.
While at it, also handle default case for the usb_role switch
in cdns3, intel-xhci-usb-role-switch & musb/jz4740 to avoid
build warnings.
Fixes: 4602f3bff2 ("usb: common: add USB GPIO based connection detection driver")
Signed-off-by: Prashanth K <quic_prashk@quicinc.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Message-ID: <1685544074-17337-1-git-send-email-quic_prashk@quicinc.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 0143d148d1e882fb1538dc9974c94d63961719b9 upstream.
The current implementation of usbdev_mmap uses usb_alloc_coherent to
allocate memory pages that will later be mapped into the user space.
Meanwhile, usb_alloc_coherent employs three different methods to
allocate memory, as outlined below:
* If hcd->localmem_pool is non-null, it uses gen_pool_dma_alloc to
allocate memory;
* If DMA is not available, it uses kmalloc to allocate memory;
* Otherwise, it uses dma_alloc_coherent.
However, it should be noted that gen_pool_dma_alloc does not guarantee
that the resulting memory will be page-aligned. Furthermore, trying to
map slab pages (i.e., memory allocated by kmalloc) into the user space
is not resonable and can lead to problems, such as a type confusion bug
when PAGE_TABLE_CHECK=y [1].
To address these issues, this patch introduces hcd_alloc_coherent_pages,
which addresses the above two problems. Specifically,
hcd_alloc_coherent_pages uses gen_pool_dma_alloc_align instead of
gen_pool_dma_alloc to ensure that the memory is page-aligned. To replace
kmalloc, hcd_alloc_coherent_pages directly allocates pages by calling
__get_free_pages.
Reported-by: syzbot+fcf1a817ceb50935ce99@syzkaller.appspotmail.comm
Closes: https://lore.kernel.org/lkml/000000000000258e5e05fae79fc1@google.com/ [1]
Fixes: f7d34b445a ("USB: Add support for usbfs zerocopy.")
Fixes: ff2437befd ("usb: host: Fix excessive alignment restriction for local memory allocations")
Cc: stable@vger.kernel.org
Signed-off-by: Ruihan Li <lrh2000@pku.edu.cn>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20230515130958.32471-2-lrh2000@pku.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 52c2d15703c3a900d5f78cd599b823db40d5100b ]
The USB "maximum-speed" property can now take the SSP signaling rate
generation and lane count with these new strings:
"super-speed-plus-gen2x2"
"super-speed-plus-gen2x1"
"super-speed-plus-gen1x2"
Introduce usb_get_maximum_ssp_rate() to parse for the corresponding
usb_ssp_rate enum. The original usb_get_maximum_speed() will return
USB_SPEED_SUPER_PLUS if it matches one of these new strings.
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/f8ed896313d8cd8e2d2b540fc82db92b3ddf8a47.1611106162.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Stable-dep-of: b6155eaf6b05 ("usb: common: debug: Check non-standard control requests")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c1e5c2f0cb8a22ec2e14af92afc7006491bebabb upstream.
Fix incorrect pin assignment values when connecting to a monitor with
Type-C receptacle instead of a plug.
According to specification, an UFP_D receptacle's pin assignment
should came from the UFP_D pin assignments field (bit 23:16), while
an UFP_D plug's assignments are described in the DFP_D pin assignments
(bit 15:8) during Mode Discovery.
For example the LG 27 UL850-W is a monitor with Type-C receptacle.
The monitor responds to MODE DISCOVERY command with following
DisplayPort Capability flag:
dp->alt->vdo=0x140045
The existing logic only take cares of UPF_D plug case,
and would take the bit 15:8 for this 0x140045 case.
This results in an non-existing pin assignment 0x0 in
dp_altmode_configure.
To fix this problem a new set of macros are introduced
to take plug/receptacle differences into consideration.
Fixes: 0e3bb7d689 ("usb: typec: Add driver for DisplayPort alternate mode")
Cc: stable@vger.kernel.org
Co-developed-by: Pablo Sun <pablo.sun@mediatek.com>
Co-developed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Reviewed-by: Guillaume Ranquet <granquet@baylibre.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Pablo Sun <pablo.sun@mediatek.com>
Signed-off-by: Macpaul Lin <macpaul.lin@mediatek.com>
Link: https://lore.kernel.org/r/20220804034803.19486-1-macpaul.lin@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26c6c2f8a907c9e3a2f24990552a4d77235791e6 upstream.
Usb core introduce the mechanism of giveback of URB in tasklet context to
reduce hardware interrupt handling time. On some test situation(such as
FIO with 4KB block size), when tasklet callback function called to
giveback URB, interrupt handler add URB node to the bh->head list also.
If check bh->head list again after finish all URB giveback of local_list,
then it may introduce a "dynamic balance" between giveback URB and add URB
to bh->head list. This tasklet callback function may not exit for a long
time, which will cause other tasklet function calls to be delayed. Some
real-time applications(such as KB and Mouse) will see noticeable lag.
In order to prevent the tasklet function from occupying the cpu for a long
time at a time, new URBS will not be added to the local_list even though
the bh->head list is not empty. But also need to ensure the left URB
giveback to be processed in time, so add a member high_prio for structure
giveback_urb_bh to prioritize tasklet and schelule this tasklet again if
bh->head list is not empty.
At the same time, we are able to prioritize tasklet through structure
member high_prio. So, replace the local high_prio_bh variable with this
structure member in usb_hcd_giveback_urb.
Fixes: 94dfd7edfd ("USB: HCD: support giveback of URB in tasklet context")
Cc: stable <stable@kernel.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Weitao Wang <WeitaoWang-oc@zhaoxin.com>
Link: https://lore.kernel.org/r/20220726074918.5114-1-WeitaoWang-oc@zhaoxin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a44623d9279086c89f631201d993aa332f7c9e66 upstream.
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
This patch has been added and reverted earier as it triggered a race
in usb device enumeration.
That race is now fixed in 5.16-rc3, and in stable back to 5.4
commit 6cca13de26ee ("usb: hub: Fix locking issues with address0_mutex")
commit 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0
race")
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20220510091630.16564-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 58877b0824da15698bd85a0a9dbfa8c354e6ecb7 upstream.
It has been observed with certain PCIe USB cards (like Inateck connected
to AM64 EVM or J7200 EVM) that as soon as the primary roothub is
registered, port status change is handled even before xHC is running
leading to cold plug USB devices not detected. For such cases, registering
both the root hubs along with the second HCD is required. Add support for
deferring roothub registration in usb_add_hcd(), so that both primary and
secondary roothubs are registered along with the second HCD.
CC: stable@vger.kernel.org # 5.4+
Suggested-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Chris Chiu <chris.chiu@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210909064200.16216-2-kishon@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit bf88fef0b6f1488abeca594d377991171c00e52a upstream.
The HNP work can be re-scheduled while it's still in-fly. This results in
re-initialization of the busy work, resetting the hrtimer's list node of
the work and crashing kernel with null dereference within kernel/timer
once work's timer is expired. It's very easy to trigger this problem by
re-plugging USB cable quickly. Initialize HNP work only once to fix this
trouble.
Unable to handle kernel NULL pointer dereference at virtual address 00000126)
...
PC is at __run_timers.part.0+0x150/0x228
LR is at __next_timer_interrupt+0x51/0x9c
...
(__run_timers.part.0) from [<c0187a2b>] (run_timer_softirq+0x2f/0x50)
(run_timer_softirq) from [<c01013ad>] (__do_softirq+0xd5/0x2f0)
(__do_softirq) from [<c012589b>] (irq_exit+0xab/0xb8)
(irq_exit) from [<c0170341>] (handle_domain_irq+0x45/0x60)
(handle_domain_irq) from [<c04c4a43>] (gic_handle_irq+0x6b/0x7c)
(gic_handle_irq) from [<c0100b65>] (__irq_svc+0x65/0xac)
Cc: stable@vger.kernel.org
Acked-by: Peter Chen <peter.chen@kernel.org>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210717182134.30262-6-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6490fa565534fa83593278267785a694fd378a2b upstream.
Current timer PD_T_SINK_WAIT_CAP is set to 240ms which will violate the
SinkWaitCapTimer (tTypeCSinkWaitCap 310 - 620 ms) defined in the PD
Spec if the port is faster enough when running the state machine. Set it
to the lower bound 310ms to ensure the timeout is in Spec.
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kyle Tso <kyletso@google.com>
Link: https://lore.kernel.org/r/20210528081613.730661-1-kyletso@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit de658a195ee23ca6aaffe197d1d2ea040beea0a2 ]
RTL8156 sends notifications about every 32ms.
Only display/log notifications when something changes.
This issue has been reported by others:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1832472https://lkml.org/lkml/2020/8/27/1083
...
[785962.779840] usb 1-1: new high-speed USB device number 5 using xhci_hcd
[785962.929944] usb 1-1: New USB device found, idVendor=0bda, idProduct=8156, bcdDevice=30.00
[785962.929949] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[785962.929952] usb 1-1: Product: USB 10/100/1G/2.5G LAN
[785962.929954] usb 1-1: Manufacturer: Realtek
[785962.929956] usb 1-1: SerialNumber: 000000001
[785962.991755] usbcore: registered new interface driver cdc_ether
[785963.017068] cdc_ncm 1-1:2.0: MAC-Address: 00:24:27:88:08:15
[785963.017072] cdc_ncm 1-1:2.0: setting rx_max = 16384
[785963.017169] cdc_ncm 1-1:2.0: setting tx_max = 16384
[785963.017682] cdc_ncm 1-1:2.0 usb0: register 'cdc_ncm' at usb-0000:00:14.0-1, CDC NCM, 00:24:27:88:08:15
[785963.019211] usbcore: registered new interface driver cdc_ncm
[785963.023856] usbcore: registered new interface driver cdc_wdm
[785963.025461] usbcore: registered new interface driver cdc_mbim
[785963.038824] cdc_ncm 1-1:2.0 enx002427880815: renamed from usb0
[785963.089586] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.121673] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
[785963.153682] cdc_ncm 1-1:2.0 enx002427880815: network connection: disconnected
...
This is about 2KB per second and will overwrite all contents of a 1MB
dmesg buffer in under 10 minutes rendering them useless for debugging
many kernel problems.
This is also an extra 180 MB/day in /var/logs (or 1GB per week) rendering
the majority of those logs useless too.
When the link is up (expected state), spew amount is >2x higher:
...
[786139.600992] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.632997] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.665097] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.697100] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
[786139.729094] cdc_ncm 2-1:2.0 enx002427880815: network connection: connected
[786139.761108] cdc_ncm 2-1:2.0 enx002427880815: 2500 mbit/s downlink 2500 mbit/s uplink
...
Chrome OS cannot support RTL8156 until this is fixed.
Signed-off-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Hayes Wang <hayeswang@realtek.com>
Link: https://lore.kernel.org/r/20210120011208.3768105-1-grundler@chromium.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Pull documentation updates from Mauro Carvalho Chehab:
"A series of patches addressing warnings produced by make htmldocs.
This includes:
- kernel-doc markup fixes
- ReST fixes
- Updates at the build system in order to support newer versions of
the docs build toolchain (Sphinx)
After this series, the number of html build warnings should reduce
significantly, and building with Sphinx 3.1 or later should now be
supported (although it is still recommended to use Sphinx 2.4.4).
As agreed with Jon, I should be sending you a late pull request by the
end of the merge window addressing remaining issues with docs build,
as there are a number of warning fixes that depends on pull requests
that should be happening along the merge window.
The end goal is to have a clean htmldocs build on Kernel 5.10.
PS. It should be noticed that Sphinx 3.0 is not currently supported,
as it lacks support for C domain namespaces. Such feature, needed in
order to document uAPI system calls with Sphinx 3.x, was added only on
Sphinx 3.1"
* tag 'docs/v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (75 commits)
PM / devfreq: remove a duplicated kernel-doc markup
mm/doc: fix a literal block markup
workqueue: fix a kernel-doc warning
docs: virt: user_mode_linux_howto_v2.rst: fix a literal block markup
Input: sparse-keymap: add a description for @sw
rcu/tree: docs: document bkvcache new members at struct kfree_rcu_cpu
nl80211: docs: add a description for s1g_cap parameter
usb: docs: document altmode register/unregister functions
kunit: test.h: fix a bad kernel-doc markup
drivers: core: fix kernel-doc markup for dev_err_probe()
docs: bio: fix a kerneldoc markup
kunit: test.h: solve kernel-doc warnings
block: bio: fix a warning at the kernel-doc markups
docs: powerpc: syscall64-abi.rst: fix a malformed table
drivers: net: hamradio: fix document location
net: appletalk: Kconfig: Fix docs location
dt-bindings: fix references to files converted to yaml
memblock: get rid of a :c:type leftover
math64.h: kernel-docs: Convert some markups into normal comments
media: uAPI: buffer.rst: remove a left-over documentation
...
The typec_bus.rst asks for documentation of those two
functions, but they don't exist:
./drivers/usb/typec/bus.c:1: warning: 'typec_altmode_unregister_driver' not found
./drivers/usb/typec/bus.c:1: warning: 'typec_altmode_register_driver' not found
Also, they're not declared on bus.c but, instead, at a header
file (typec_altmode.h).
So, add documentation for both functions at the header and
change the kernel-doc markup under typec_bus.rst to point
to the right place.
While here, also place the documentation for both structs
declared on typec_altmode.h at the rst file.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
PD 3.0 spec defines a new mechanism for power role swap called
Fast role swap. This change enables TCPM to support FRS when
acting as sink.
Once the explicit contract is negotiated, sink port is
expected to query the source port for sink caps to
determine whether the source is FRS capable.
Bits 23 & 24 of fixed pdo of the sink caps from the source, when
set, indicates the current needed by the source when fast role
swap is in progress(Implicit contract phasae). 0 indicates that
the source does not support Fast Role Swap.
Upon receiving the FRS signal from the source,
TCPC(TCPM_FRS_EVENT) informs TCPM to start the Fast role swap sequence.
1. TCPM sends FRS PD message: FR_SWAP_SEND
2. If response is not received within the expiry of
SenderResponseTimer, Error recovery is triggered.:
FR_SWAP_SEND_TIMEOUT
3. Upon receipt of the accept message, TCPM waits for
PSSourceOffTimer for PS_READY message from the partner:
FR_SWAP_SNK_SRC_NEW_SINK_READY.
TCPC is expected to autonomously turn on vbus once the FRS
signal is received and vbus voltage falls below vsafe5v within
tSrcFrSwap. This is different from traditional power role swap
where the vbus sourcing is turned on by TCPM.
4. By this time, TCPC most likely would have started to
source vbus, TCPM waits for tSrcFrSwap to see if the
lower level TCPC driver signals TCPM_SOURCING_VBUS event:
FR_SWAP_SNK_SRC_SOURCE_VBUS_APPLIED.
5. When TCPC signals sourcing vbus, TCPM sends PS_READY msg and
changes the CC pin from Rd to Rp. This is the end of fast
role swap sequence and TCPM initiates the sequnce to negotiate
explicit contract by transitioning into SRC_STARTUP after
SwapSrcStart.
The code is written based on the sequence described in "Figure 8-107:
Dual-role Port in Sink to Source Fast Role Swap State Diagram" of
USB Power Delivery Specification Revision 3.0, Version 1.2.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20201008061556.1402293-7-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe writes:
USB: changes for v5.10 merge window
Most of changes are on dwc3 (38.8%) with cdns3 falling close
behind (24.1%).
The biggest changes here are a series of non-critical fixes to corner
cases on dwc3, produced by Thinh N, and a series of major improvements
to cdns3 produced by Peter C.
We also have the traditional set of new device support (Intel Keem
Bay, Hikey 970) on dwc3. A series of sparse/coccinelle and checkpatch
fixes on dwc3 by yours truly and a set of minor changes all over the
stack.
* tag 'usb-for-v5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (117 commits)
usb: dwc2: Fix INTR OUT transfers in DDMA mode.
usb: dwc2: don't use ID/Vbus detection if usb-role-switch on STM32MP15 SoCs
usb: dwc2: override PHY input signals with usb role switch support
dt-bindings: usb: dwc2: add optional usb-role-switch property
usb: dwc3: of-simple: Add compatible string for Intel Keem Bay platform
dt-bindings: usb: Add Intel Keem Bay USB controller bindings
usb: dwc3: gadget: Support up to max stream id
usb: dwc3: gadget: Return early if no TRB update
usb: dwc3: gadget: Keep TRBs in request order
usb: dwc3: gadget: Revise setting IOC when no TRB left
usb: dwc3: gadget: Look ahead when setting IOC
usb: dwc3: gadget: Allow restarting a transfer
usb: bdc: remove duplicated error message
usb: dwc3: Stop active transfers before halting the controller
usb: cdns3: gadget: enlarge the TRB ring length
usb: cdns3: gadget: sg_support is only for DEV_VER_V2 or above
usb: cdns3: gadget: need to handle sg case for workaround 2 case
usb: cdns3: gadget: handle sg list use case at completion correctly
usb: cdns3: gadget: add CHAIN and ISP bit for sg list use case
usb: cdns3: gadget: improve the dump TRB operation at cdns3_ep_run_transfer
...
The routines used by the UDC core to interface with the kernel's
device model, namely usb_add_gadget_udc(),
usb_add_gadget_udc_release(), and usb_del_gadget_udc(), provide access
to only a subset of the device model's full API. They include
functionality equivalent to device_register() and device_unregister()
for gadgets, but they omit device_initialize(), device_add(),
device_del(), get_device(), and put_device().
This patch expands the UDC API by adding usb_initialize_gadget(),
usb_add_gadget(), usb_del_gadget(), usb_get_gadget(), and
usb_put_gadget() to fill in the gap. It rewrites the existing
routines to call the new ones.
CC: Anton Vasilyev <vasilyev@ispras.ru>
CC: Evgeny Novikov <novikov@ispras.ru>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
The patch addresses the compliance test failures while running
TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 of the "Deterministic PD
Compliance MOI" test plan published in https://www.usb.org/usbc.
For a product to be Type-C compliant, it's expected that these tests
are run on usb.org certified Type-C compliance tester as mentioned in
https://www.usb.org/usbc.
The purpose of the tests TD.PD.CP.E3, TD.PD.CP.E4, TD.PD.CP.E5 is to
verify the PR_SWAP response of the device. While doing so, the test
asserts that Source Capabilities message is NOT received from the test
device within tSwapSourceStart min (20 ms) from the time the last bit
of GoodCRC corresponding to the RS_RDY message sent by the UUT was
sent. If it does then the test fails.
This is in line with the requirements from the USB Power Delivery
Specification Revision 3.0, Version 1.2:
"6.6.8.1 SwapSourceStartTimer
The SwapSourceStartTimer Shall be used by the new Source, after a
Power Role Swap or Fast Role Swap, to ensure that it does not send
Source_Capabilities Message before the new Sink is ready to receive
the
Source_Capabilities Message. The new Source Shall Not send the
Source_Capabilities Message earlier than tSwapSourceStart after the
last bit of the EOP of GoodCRC Message sent in response to the PS_RDY
Message sent by the new Source indicating that its power supply is
ready."
The patch makes sure that TCPM does not send the Source_Capabilities
Message within tSwapSourceStart(20ms) by transitioning into
SRC_STARTUP only after tSwapSourceStart(20ms).
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200817183828.1895015-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
Peter writes:
ENDIAN issue fix and one query controller role API is introduced.
* tag 'usb-ci-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: imx: get available runtime dr mode for wakeup setting
usb: chipidea: add query_available_role interface
Documentation: ABI: usb: chipidea: Update Li Jun's e-mail
usb: chipidea: udc: fix the ENDIAN issue
Johan writes:
USB-serial updates for 5.9-rc1
Here are the USB-serial updates for 5.9-rc1, including:
- console flow-control support
- simulated line-breaks on some ch341
- hardware flow-control fixes for cp210x
- break-detection and sysrq fixes for ftdi_sio
- sysrq optimisations
- input parity checking for cp210x
Included are also some new device ids and various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.9-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (31 commits)
USB: serial: qcserial: add EM7305 QDL product ID
USB: serial: iuu_phoenix: fix led-activity helpers
USB: serial: sierra: clean up special-interface handling
USB: serial: cp210x: use in-kernel types in port data
USB: serial: cp210x: drop unnecessary packed attributes
USB: serial: cp210x: add support for TIOCGICOUNT
USB: serial: cp210x: add support for line-status events
USB: serial: cp210x: disable interface on errors in open
USB: serial: drop redundant transfer-buffer casts
USB: serial: drop extern keyword from function declarations
USB: serial: drop unnecessary sysrq include
USB: serial: add sysrq break-handler dummy
USB: serial: inline sysrq dummy function
USB: serial: only process sysrq when enabled
USB: serial: only set sysrq timestamp for consoles
USB: serial: ftdi_sio: fix break and sysrq handling
USB: serial: ftdi_sio: clean up receive processing
USB: serial: ftdi_sio: make process-packet buffer unsigned
USB: serial: use fallthrough pseudo-keyword
USB: serial: ch341: fix missing simulated-break margin
...
The glue layer may need to know current available role to do some
setting, eg, the wakeup setting. So we add ci_hdrc_query_available_role
for that.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719160910.60018-1-grandmaster@al2klimov.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Port starts to toggle when transitioning to unattached state.
This is incorrect while in BIST mode.
6.4.3.1 BIST Carrier Mode
Upon receipt of a BIST Message, with a BIST Carrier Mode BIST Data Object,
the UUT Shall send out a continuous string of BMC encoded alternating "1"s
and “0”s. The UUT Shall exit the Continuous BIST Mode within
tBISTContMode of this Continuous BIST Mode being enabled(see
Section 6.6.7.2).
6.4.3.2 BIST Test Data
Upon receipt of a BIST Message, with a BIST Test Data BIST Data Object,
the UUT Shall return a GoodCRC Message and Shall enter a test mode in which
it sends no further Messages except for GoodCRC Messages in response to
received Messages. See Section 5.9.2 for the definition of the Test Data
Frame. The test Shall be ended by sending Hard Reset Signaling to reset the
UUT.
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20200716034128.1251728-3-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This function can be reused by other usbnet minidrivers.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop the redundant extern keyword from function declarations in the
subsystem header file to improve readability (and make it easier to spot
the global variables).
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add inline sysrq break-handler dummy to allow the compiler to eliminate
further code when either console or sysrq support isn't enabled and to
clearly mark the two sysrq functions as belonging together.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Inline the dummy sysrq character handling when either console support or
magic-sysrq support isn't enabled to allow the compiler to eliminate
unused code.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This data structure can be delivered to the mux drivers when
Enter_USB Message is used exactly the same way as the
Alternate Mode specific data structures are delivered to the
mux drivers when Enter Mode Messages are used.
The Enter_USB data structure shall have all details related
to the Enter_USB Message, most importantly the Enter_USB
Date Object that was used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20200701115618.22482-3-heikki.krogerus@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Peter writes:
- Some improvments for ci_hdrc_usb2.c
- Support imx7d USB charger
- Add software sg support for UDC
- Enable user trigger role switch
* tag 'usb-ci-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb:
usb: chipidea: Enable user-space triggered role-switching
usb: chipidea: udc: add software sg list support
usb: chipidea: usbmisc_imx: using different ops for imx7d and imx7ulp
usb: chipidea: pull down dp for possible charger detection operation
usb: chipidea: introduce imx7d USB charger detection
usb: chipidea: introduce CI_HDRC_CONTROLLER_VBUS_EVENT glue layer use
usb: chipidea: usb2: remove unneeded semicolon
usb: chipidea: allow disabling glue drivers if EMBEDDED
usb: chipidea: usb2: absorb zevio glue driver
usb: chipidea: usb2: make clock optional
usb: chipidea: usb2: fix formatting
usb: chipidea: usb2: constify zynq_pdata
usb: chipidea: core: show the real pointer value for register
usb: chipidea: core: refine the description for this driver
usb: chipidea: udc: fix the kernel doc for udc.h
Felipe writes:
USB: changes for v5.8 merge window
Rather busy cycle. We have a total 99 non-merge commits going into v5.8
merge window. The majority of the changes are in dwc3 this around (31.7%
of all changes). It's composed mostly Thinh's recent updates to get dwc3
to behave correctly with stream transfers. We have also have Roger's for
Keystone platforms and Neil's updates for the meson glue layer.
Apart from those, we have the usual set of non-critical fixes, new
device IDs, spelling fixes all over the place.
Signed-off-by: Felipe Balbi <balbi@kernel.org>
* tag 'usb-for-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb: (99 commits)
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
usb: dwc3: gadget: Check for prepared TRBs
usb: gadget: Fix issue with config_ep_by_speed function
usb: cdns3: ep0: delete the redundant status stage
usb: dwc2: Update Core Reset programming flow.
usb: gadget: fsl: Fix a wrong judgment in fsl_udc_probe()
usb: gadget: fix potential double-free in m66592_probe.
usb: cdns3: Fix runtime PM imbalance on error
usb: gadget: lpc32xx_udc: don't dereference ep pointer before null check
usb: dwc3: Increase timeout for CmdAct cleared by device controller
USB: dummy-hcd: use configurable endpoint naming scheme
usb: cdns3: gadget: assign interrupt number to USB gadget structure
usb: gadget: core: sync interrupt before unbind the udc
arm64: dts: qcom: sc7180: Add interconnect properties for USB
arm64: dts: qcom: sdm845: Add interconnect properties for USB
dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver
ARM: dts: at91: Remove the USB EP child node
dt-bindings: usb: atmel: Mark EP child node as deprecated
...
This patch adds new config_ep_by_speed_and_alt function which
extends the config_ep_by_speed about alt parameter.
This additional parameter allows to find proper usb_ss_ep_comp_descriptor.
Problem has appeared during testing f_tcm (BOT/UAS) driver function.
f_tcm function for SS use array of headers for both BOT/UAS alternate
setting:
static struct usb_descriptor_header *uasp_ss_function_desc[] = {
(struct usb_descriptor_header *) &bot_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &bot_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &bot_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_intf_desc,
(struct usb_descriptor_header *) &uasp_ss_bi_desc,
(struct usb_descriptor_header *) &uasp_bi_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bi_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_bo_desc,
(struct usb_descriptor_header *) &uasp_bo_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_bo_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_status_desc,
(struct usb_descriptor_header *) &uasp_status_in_ep_comp_desc,
(struct usb_descriptor_header *) &uasp_status_pipe_desc,
(struct usb_descriptor_header *) &uasp_ss_cmd_desc,
(struct usb_descriptor_header *) &uasp_cmd_comp_desc,
(struct usb_descriptor_header *) &uasp_cmd_pipe_desc,
NULL,
};
The first 5 descriptors are associated with BOT alternate setting,
and others are associated with UAS.
During handling UAS alternate setting f_tcm driver invokes
config_ep_by_speed and this function sets incorrect companion endpoint
descriptor in usb_ep object.
Instead setting ep->comp_desc to uasp_bi_ep_comp_desc function in this
case set ep->comp_desc to uasp_ss_bi_desc.
This is due to the fact that it searches endpoint based on endpoint
address:
for_each_ep_desc(speed_desc, d_spd) {
chosen_desc = (struct usb_endpoint_descriptor *)*d_spd;
if (chosen_desc->bEndpoitAddress == _ep->address)
goto ep_found;
}
And in result it uses the descriptor from BOT alternate setting
instead UAS.
Finally, it causes that controller driver during enabling endpoints
detect that just enabled endpoint for bot.
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
