commit 0a907ee9d95e3ac35eb023d71f29eae0aaa52d1b upstream.
of_node_put should always be called on device nodes gotten from
of_get_*. Additionally, it should only be called after there are no
remaining users. To address the first issue, call of_node_put if later
steps in ulpi_register fail. To address the latter, call put_device if
device_register fails, which will call ulpi_dev_release if necessary.
Fixes: ef6a7bcfb0 ("usb: ulpi: Support device discovery via DT")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Link: https://lore.kernel.org/r/20220127190004.1446909-3-sean.anderson@seco.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 269cbcf7b72de6f0016806d4a0cec1d689b55a87 upstream.
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable@kernel.org
Reviewed-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644423353-17859-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ebe2b1add1055b903e2acd86b290a85297edc0b3 ]
Consider a case where ffs_func_eps_disable is called from
ffs_func_disable as part of composition switch and at the
same time ffs_epfile_release get called from userspace.
ffs_epfile_release will free up the read buffer and call
ffs_data_closed which in turn destroys ffs->epfiles and
mark it as NULL. While this was happening the driver has
already initialized the local epfile in ffs_func_eps_disable
which is now freed and waiting to acquire the spinlock. Once
spinlock is acquired the driver proceeds with the stale value
of epfile and tries to free the already freed read buffer
causing use-after-free.
Following is the illustration of the race:
CPU1 CPU2
ffs_func_eps_disable
epfiles (local copy)
ffs_epfile_release
ffs_data_closed
if (last file closed)
ffs_data_reset
ffs_data_clear
ffs_epfiles_destroy
spin_lock
dereference epfiles
Fix this races by taking epfiles local copy & assigning it under
spinlock and if epfiles(local) is null then update it in ffs->epfiles
then finally destroy it.
Extending the scope further from the race, protecting the ep related
structures, and concurrent accesses.
Fixes: a9e6f83c2d ("usb: gadget: f_fs: stop sleeping in ffs_func_eps_disable")
Co-developed-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Pratham Pratap <quic_ppratap@quicinc.com>
Signed-off-by: Udipto Goswami <quic_ugoswami@quicinc.com>
Link: https://lore.kernel.org/r/1643256595-10797-1-git-send-email-quic_ugoswami@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac55d163855924aa5af9f1560977da8f346963c8 ]
Calling dwc2_hsotg_ep_disable on ep0 (in/out) will lead to the following
logs before returning -EINVAL:
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
To avoid these two logs while suspending, start disabling the endpoint
from the index 1, as done in dwc2_hsotg_udc_stop:
/* all endpoints should be shutdown */
for (ep = 1; ep < hsotg->num_of_eps; ep++) {
if (hsotg->eps_in[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_in[ep]->ep);
if (hsotg->eps_out[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_out[ep]->ep);
}
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207130101.270314-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 825911492eb15bf8bb7fb94bc0c0421fe7a6327d upstream.
CCGx clears Bit 0:Device Interrupt in the INTR_REG
if CCGx is reset successfully. However, there might
be a chance that other bits in INTR_REG are not
cleared due to internal data queued in PPM. This case
misleads the driver that CCGx reset failed.
The commit checks bit 0 in INTR_REG and ignores other
bits. The ucsi driver would reset PPM later.
Fixes: 247c554a14 ("usb: typec: ucsi: add support for Cypress CCGx")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 90b8aa9f5b09edae6928c0561f933fec9f7a9987 upstream.
With some chargers, vbus might momentarily raise above VSAFE5V and fall
back to 0V before tcpm gets to read port->tcpc->get_vbus. This will
will report a VBUS off event causing TCPM to transition to
SNK_UNATTACHED where it should be waiting in either SNK_ATTACH_WAIT
or SNK_DEBOUNCED state. This patch makes TCPM avoid vbus off events
while in SNK_ATTACH_WAIT or SNK_DEBOUNCED state.
Stub from the spec:
"4.5.2.2.4.2 Exiting from AttachWait.SNK State
A Sink shall transition to Unattached.SNK when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce.
A DRP shall transition to Unattached.SRC when the state of both
the CC1 and CC2 pins is SNK.Open for at least tPDDebounce."
[23.194131] CC1: 0 -> 0, CC2: 0 -> 5 [state SNK_UNATTACHED, polarity 0, connected]
[23.201777] state change SNK_UNATTACHED -> SNK_ATTACH_WAIT [rev3 NONE_AMS]
[23.209949] pending state change SNK_ATTACH_WAIT -> SNK_DEBOUNCED @ 170 ms [rev3 NONE_AMS]
[23.300579] VBUS off
[23.300668] state change SNK_ATTACH_WAIT -> SNK_UNATTACHED [rev3 NONE_AMS]
[23.301014] VBUS VSAFE0V
[23.301111] Start toggling
Fixes: f0690a25a1 ("staging: typec: USB Type-C Port Manager (tcpm)")
Cc: stable@vger.kernel.org
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Badhri Jagan Sridharan <badhri@google.com>
Link: https://lore.kernel.org/r/20220122015520.332507-1-badhri@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26fbe9772b8c459687930511444ce443011f86bf upstream.
The syzbot fuzzer has identified a bug in which processes hang waiting
for usb_kill_urb() to return. It turns out the issue is not unlinking
the URB; that works just fine. Rather, the problem arises when the
wakeup notification that the URB has completed is not received.
The reason is memory-access ordering on SMP systems. In outline form,
usb_kill_urb() and __usb_hcd_giveback_urb() operating concurrently on
different CPUs perform the following actions:
CPU 0 CPU 1
---------------------------- ---------------------------------
usb_kill_urb(): __usb_hcd_giveback_urb():
... ...
atomic_inc(&urb->reject); atomic_dec(&urb->use_count);
... ...
wait_event(usb_kill_urb_queue,
atomic_read(&urb->use_count) == 0);
if (atomic_read(&urb->reject))
wake_up(&usb_kill_urb_queue);
Confining your attention to urb->reject and urb->use_count, you can
see that the overall pattern of accesses on CPU 0 is:
write urb->reject, then read urb->use_count;
whereas the overall pattern of accesses on CPU 1 is:
write urb->use_count, then read urb->reject.
This pattern is referred to in memory-model circles as SB (for "Store
Buffering"), and it is well known that without suitable enforcement of
the desired order of accesses -- in the form of memory barriers -- it
is entirely possible for one or both CPUs to execute their reads ahead
of their writes. The end result will be that sometimes CPU 0 sees the
old un-decremented value of urb->use_count while CPU 1 sees the old
un-incremented value of urb->reject. Consequently CPU 0 ends up on
the wait queue and never gets woken up, leading to the observed hang
in usb_kill_urb().
The same pattern of accesses occurs in usb_poison_urb() and the
failure pathway of usb_hcd_submit_urb().
The problem is fixed by adding suitable memory barriers. To provide
proper memory-access ordering in the SB pattern, a full barrier is
required on both CPUs. The atomic_inc() and atomic_dec() accesses
themselves don't provide any memory ordering, but since they are
present, we can use the optimized smp_mb__after_atomic() memory
barrier in the various routines to obtain the desired effect.
This patch adds the necessary memory barriers.
CC: <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+76629376e06e2c2ad626@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8K0QYee0Q0Nna2@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2e3dd4a6246945bf84ea6f478365d116e661554c upstream.
Commit 7495af930835 ("ARM: multi_v7_defconfig: Enable drivers for
DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM
multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash
on the Tegra20 Ventana platform in the ulpi_match() function.
The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS,
registers a ulpi_driver but this driver does not provide an 'id_table',
so when ulpi_match() is called on the Tegra20 Ventana platform, it
crashes when attempting to deference the id_table pointer which is not
valid. The Qualcomm USB HS PHY driver uses device-tree for matching the
ULPI driver with the device and so fix this crash by using device-tree
for matching if the id_table is not valid.
Fixes: ef6a7bcfb0 ("usb: ulpi: Support device discovery via DT")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5b67b315037250a61861119683e7fcb509deea25 upstream.
Two people have reported (and mentioned numerous other reports on the
web) that VIA's VL817 USB-SATA bridge does not work with the uas
driver. Typical log messages are:
[ 3606.232149] sd 14:0:0:0: [sdg] tag#2 uas_zap_pending 0 uas-tag 1 inflight: CMD
[ 3606.232154] sd 14:0:0:0: [sdg] tag#2 CDB: Write(16) 8a 00 00 00 00 00 18 0c c9 80 00 00 00 80 00 00
[ 3606.306257] usb 4-4.4: reset SuperSpeed Plus Gen 2x1 USB device number 11 using xhci_hcd
[ 3606.328584] scsi host14: uas_eh_device_reset_handler success
Surprisingly, the devices do seem to work okay for some other people.
The cause of the differing behaviors is not known.
In the hope of getting the devices to work for the most users, even at
the possible cost of degraded performance for some, this patch adds an
unusual_devs entry for the VL817 to block it from binding to the uas
driver by default. Users will be able to override this entry by means
of a module parameter, if they want.
CC: <stable@vger.kernel.org>
Reported-by: DocMAX <mail@vacharakis.de>
Reported-and-tested-by: Thomas Weißschuh <linux@weissschuh.net>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/Ye8IsK2sjlEv1rqU@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 00558586382891540c59c9febc671062425a6e47 ]
When a new USB device gets plugged to nested hubs, the affected hub,
which connects to usb 2-1.4-port2, doesn't report there's any change,
hence the nested hubs go back to runtime suspend like nothing happened:
[ 281.032951] usb usb2: usb wakeup-resume
[ 281.032959] usb usb2: usb auto-resume
[ 281.032974] hub 2-0:1.0: hub_resume
[ 281.033011] usb usb2-port1: status 0263 change 0000
[ 281.033077] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.049797] usb 2-1: usb wakeup-resume
[ 281.069800] usb 2-1: Waited 0ms for CONNECT
[ 281.069810] usb 2-1: finish resume
[ 281.070026] hub 2-1:1.0: hub_resume
[ 281.070250] usb 2-1-port4: status 0203 change 0000
[ 281.070272] usb usb2-port1: resume, status 0
[ 281.070282] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.089813] usb 2-1.4: usb wakeup-resume
[ 281.109792] usb 2-1.4: Waited 0ms for CONNECT
[ 281.109801] usb 2-1.4: finish resume
[ 281.109991] hub 2-1.4:1.0: hub_resume
[ 281.110147] usb 2-1.4-port2: status 0263 change 0000
[ 281.110234] usb 2-1-port4: resume, status 0
[ 281.110239] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.110266] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.110426] hub 2-1.4:1.0: hub_suspend
[ 281.110565] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.130998] hub 2-1:1.0: hub_suspend
[ 281.137788] usb 2-1: usb auto-suspend, wakeup 1
[ 281.142935] hub 2-0:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.177828] usb 2-1: usb wakeup-resume
[ 281.197839] usb 2-1: Waited 0ms for CONNECT
[ 281.197850] usb 2-1: finish resume
[ 281.197984] hub 2-1:1.0: hub_resume
[ 281.198203] usb 2-1-port4: status 0203 change 0000
[ 281.198228] usb usb2-port1: resume, status 0
[ 281.198237] hub 2-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 281.217835] usb 2-1.4: usb wakeup-resume
[ 281.237834] usb 2-1.4: Waited 0ms for CONNECT
[ 281.237845] usb 2-1.4: finish resume
[ 281.237990] hub 2-1.4:1.0: hub_resume
[ 281.238067] usb 2-1.4-port2: status 0263 change 0000
[ 281.238148] usb 2-1-port4: resume, status 0
[ 281.238152] usb 2-1-port4: status 0203, change 0000, 10.0 Gb/s
[ 281.238166] hub 2-1.4:1.0: state 7 ports 4 chg 0000 evt 0000
[ 281.238385] hub 2-1.4:1.0: hub_suspend
[ 281.238523] usb 2-1.4: usb auto-suspend, wakeup 1
[ 281.258076] hub 2-1:1.0: hub_suspend
[ 281.265744] usb 2-1: usb auto-suspend, wakeup 1
[ 281.285976] hub 2-0:1.0: hub_suspend
[ 281.285988] usb usb2: bus auto-suspend, wakeup 1
USB 3.2 spec, 9.2.5.4 "Changing Function Suspend State" says that "If
the link is in a non-U0 state, then the device must transition the link
to U0 prior to sending the remote wake message", but the hub only
transits the link to U0 after signaling remote wakeup.
So be more forgiving and use a 20ms delay to let the link transit to U0
for remote wakeup.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20211215120108.336597-1-kai.heng.feng@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c76ef96fc00eb398c8fc836b0eb2f82bcc619dc7 ]
Function fs endpoint file operations are synchronized via an interruptible
mutex wait. However we see threads that do ep file operations concurrently
are getting blocked for the mutex lock in __fdget_pos(). This is an
uninterruptible wait and we see hung task warnings and kernel panic
if hung_task_panic systcl is enabled if host does not send/receive
the data for long time.
The reason for threads getting blocked in __fdget_pos() is due to
the file position protection introduced by the commit 9c225f2655
("vfs: atomic f_pos accesses as per POSIX"). Since function fs
endpoint files does not have the notion of the file position, switch
to the stream mode. This will bypass the file position mutex and
threads will be blocked in interruptible state for the function fs
mutex.
It should not affects user space as we are only changing the task state
changes the task state from UNINTERRUPTIBLE to INTERRUPTIBLE while waiting
for the USB transfers to be finished. However there is a slight change to
the O_NONBLOCK behavior. Earlier threads that are using O_NONBLOCK are also
getting blocked inside fdget_pos(). Now they reach to function fs and error
code is returned. The non blocking behavior is actually honoured now.
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Link: https://lore.kernel.org/r/1636712682-1226-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b52fe2dbb3e655eb1483000adfab68a219549e13 ]
Since the acpi_create_platform_device() function may return error
pointers, dwc3_qcom_create_urs_usb_platdev() function may return error
pointers too. Using IS_ERR_OR_NULL() to check the return value to fix this.
Fixes: c25c210f590e ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20211222111823.22887-1-linmq006@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1d7d4c07932e04355d6e6528d44a2f2c9e354346 upstream.
When the USB core code for getting root-hub status reports was
originally written, it was assumed that the hub driver would be its
only caller. But this isn't true now; user programs can use usbfs to
communicate with root hubs and get status reports. When they do this,
they may use a transfer_buffer that is smaller than the data returned
by the HCD, which will lead to a buffer overflow error when
usb_hcd_poll_rh_status() tries to store the status data. This was
discovered by syzbot:
BUG: KASAN: slab-out-of-bounds in memcpy include/linux/fortify-string.h:225 [inline]
BUG: KASAN: slab-out-of-bounds in usb_hcd_poll_rh_status+0x5f4/0x780 drivers/usb/core/hcd.c:776
Write of size 2 at addr ffff88801da403c0 by task syz-executor133/4062
This patch fixes the bug by reducing the amount of status data if it
won't fit in the transfer_buffer. If some data gets discarded then
the URB's completion status is set to -EOVERFLOW rather than 0, to let
the user know what happened.
Reported-and-tested-by: syzbot+3ae6a2b06f131ab9849f@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Yc+3UIQJ2STbxNua@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0f663729bb4afc92a9986b66131ebd5b8a9254d1 upstream.
Bugzilla #213839 reports a 7-port hub that doesn't work properly when
devices are plugged into some of the ports; the kernel goes into an
unending disconnect/reinitialize loop as shown in the bug report.
This "7-port hub" comprises two four-port hubs with one plugged into
the other; the failures occur when a device is plugged into one of the
downstream hub's ports. (These hubs have other problems too. For
example, they bill themselves as USB-2.0 compliant but they only run
at full speed.)
It turns out that the failures are caused by bugs in both the kernel
and the hub. The hub's bug is that it reports a different
bmAttributes value in its configuration descriptor following a remote
wakeup (0xe0 before, 0xc0 after -- the wakeup-support bit has
changed).
The kernel's bug is inside the hub driver's resume handler. When
hub_activate() sees that one of the hub's downstream ports got a
wakeup request from a child device, it notes this fact by setting the
corresponding bit in the hub->change_bits variable. But this variable
is meant for connection changes, not wakeup events; setting it causes
the driver to believe the downstream port has been disconnected and
then connected again (in addition to having received a wakeup
request).
Because of this, the hub driver then tries to check whether the device
currently plugged into the downstream port is the same as the device
that had been attached there before. Normally this check succeeds and
wakeup handling continues with no harm done (which is why the bug
remained undetected until now). But with these dodgy hubs, the check
fails because the config descriptor has changed. This causes the hub
driver to reinitialize the child device, leading to the
disconnect/reinitialize loop described in the bug report.
The proper way to note reception of a downstream wakeup request is
to set a bit in the hub->event_bits variable instead of
hub->change_bits. That way the hub driver will realize that something
has happened to the port but will not think the port and child device
have been disconnected. This patch makes that change.
Cc: <stable@vger.kernel.org>
Tested-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/YdCw7nSfWYPKWQoD@rowland.harvard.edu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e4844092581ceec22489b66c42edc88bc6079783 upstream.
The Fresco Logic FL1100 controller needs the TRUST_TX_LENGTH quirk like
other Fresco controllers, but should not have the BROKEN_MSI quirks set.
BROKEN_MSI quirk causes issues in detecting usb drives connected to docks
with this FL1100 controller.
The BROKEN_MSI flag was apparently accidentally set together with the
TRUST_TX_LENGTH quirk
Original patch went to stable so this should go there as well.
Fixes: ea0f69d82119 ("xhci: Enable trust tx length quirk for Fresco FL11 USB controller")
Cc: stable@vger.kernel.org
cc: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211221112825.54690-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 890d5b40908bfd1a79be018d2d297cf9df60f4ee upstream.
When listening for notifications through netlink of a new interface being
registered, sporadically, it is possible for the MAC to be read as zero.
The zero MAC address lasts a short period of time and then switches to a
valid random MAC address.
This causes problems for netd in Android, which assumes that the interface
is malfunctioning and will not use it.
In the good case we get this log:
InterfaceController::getCfg() ifName usb0
hwAddr 92:a8:f0:73:79:5b ipv4Addr 0.0.0.0 flags 0x1002
In the error case we get these logs:
InterfaceController::getCfg() ifName usb0
hwAddr 00:00:00:00:00:00 ipv4Addr 0.0.0.0 flags 0x1002
netd : interfaceGetCfg("usb0")
netd : interfaceSetCfg() -> ServiceSpecificException
(99, "[Cannot assign requested address] : ioctl() failed")
The reason for the issue is the order in which the interface is setup,
it is first registered through register_netdev() and after the MAC
address is set.
Fixed by first setting the MAC address of the net_device and after that
calling register_netdev().
Fixes: bcd4a1c40b ("usb: gadget: u_ether: construct with default values and add setters/getters")
Cc: stable@vger.kernel.org
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Link: https://lore.kernel.org/r/20211204214912.17627-1-posteuca@mutex.one
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 83b67041f3eaf33f98a075249aa7f4c7617c2f85 upstream.
When generalising GPIO support and adding support for CP2102N, the GPIO
registration for some CP2105 devices accidentally broke. Specifically,
when all the pins of a port are in "modem" mode, and thus unavailable
for GPIO use, the GPIO chip would now be registered without having
initialised the number of GPIO lines. This would in turn be rejected by
gpiolib and some errors messages would be printed (but importantly probe
would still succeed).
Fix this by initialising the number of GPIO lines before registering the
GPIO chip.
Note that as for the other device types, and as when all CP2105 pins are
muxed for LED function, the GPIO chip is registered also when no pins
are available for GPIO use.
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Link: https://lore.kernel.org/r/5eb560c81d2ea1a2b4602a92d9f48a89@vanmierlo.com
Fixes: c8acfe0aad ("USB: serial: cp210x: implement GPIO support for CP2102N")
Cc: stable@vger.kernel.org # 4.19
Cc: Karoly Pados <pados@pados.hu>
Link: https://lore.kernel.org/r/20211126094348.31698-1-johan@kernel.org
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tested-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit fac6bf87c55f7f0733efb0375565fb6a50cf2caf upstream.
When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.
Fixes: a415083a11 ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS")
Cc: stable <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit f08adf5add9a071160c68bb2a61d697f39ab0758 ]
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
Fix that up by only checking the single bit.
Fixes: 153a2d7e3350 ("USB: gadget: detect too-big endpoint 0 requests")
Cc: Felipe Balbi <balbi@kernel.org>
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20211214184621.385828-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7faac1953ed1f658f719cdf7bb7303fa5eef822c upstream.
Make xhci_disable_slot() synchronous, thus ensuring it, and
xhci_free_dev() calling it return after xHC controller completes
the disable slot command.
Otherwise the roothub and xHC host may runtime suspend, and clear the
command ring while the disable slot command is being processed.
This causes a command completion mismatch as the completion event can't
be mapped to the correct command.
Command ring gets out of sync and commands time out.
Driver finally assumes host is unresponsive and bails out.
usb 2-4: USB disconnect, device number 10
xhci_hcd 0000:00:0d.0: ERROR mismatched command completion event
...
xhci_hcd 0000:00:0d.0: xHCI host controller not responding, assume dead
xhci_hcd 0000:00:0d.0: HC died; cleaning up
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 811ae81320da53a5670c36970cefacca8519f90e upstream.
When the xHCI is quirked with XHCI_RESET_ON_RESUME, runtime resume
routine also resets the controller.
This is bad for USB drivers without reset_resume callback, because
there's no subsequent call of usb_dev_complete() ->
usb_resume_complete() to force rebinding the driver to the device. For
instance, btusb device stops working after xHCI controller is runtime
resumed, if the controlled is quirked with XHCI_RESET_ON_RESUME.
So always take XHCI_RESET_ON_RESUME into account to solve the issue.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210141735.1384209-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 1a3910c80966e4a76b25ce812f6bea0ef1b1d530 upstream.
The checks performed by commit aed9d65ac3 ("USB: validate
wMaxPacketValue entries in endpoint descriptors") require that initial
value of the maxp variable contains both maximum packet size bits
(10..0) and multiple-transactions bits (12..11). However, the existing
code assings only the maximum packet size bits. This patch assigns all
bits of wMaxPacketSize to the variable.
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Pavel Hofman <pavel.hofman@ivitera.com>
Link: https://lore.kernel.org/r/20211210085219.16796-1-pavel.hofman@ivitera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 86ebbc11bb3f60908a51f3e41a17e3f477c2eaa3 upstream.
Under some conditions, USB gadget devices can show allocated buffer
contents to a host. Fix this up by zero-allocating them so that any
extra data will all just be zeros.
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Tested-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 153a2d7e3350cc89d406ba2d35be8793a64c2038 upstream.
Sometimes USB hosts can ask for buffers that are too large from endpoint
0, which should not be allowed. If this happens for OUT requests, stall
the endpoint, but for IN requests, trim the request size to the endpoint
buffer size.
Co-developed-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 72ee48ee8925446eaeda8e4ef3f2eb16b4a93d2a upstream.
Currently, the UVC function is activated when open on the corresponding
v4l2 device is called. On another open the activation of the function
fails since the deactivation counter in `usb_function_activate` equals
0. However the error is not returned to userspace since the open of the
v4l2 device is successful.
On a close the function is deactivated (since deactivation counter still
equals 0) and the video is disabled in `uvc_v4l2_release`, although the
UVC application potentially is streaming.
Move activation of UVC function to subscription on UVC_EVENT_SETUP
because there we can guarantee for a userspace application utilizing
UVC. Block subscription on UVC_EVENT_SETUP while another application
already is subscribed to it, indicated by `bool func_connected` in
`struct uvc_device`. Extend the `struct uvc_file_handle` with member
`bool is_uvc_app_handle` to tag it as the handle used by the userspace
UVC application.
With this a process is able to check capabilities of the v4l2 device
without deactivating the function for the actual UVC application.
Reviewed-By: Michael Tretter <m.tretter@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@wolfvision.net>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/20211003201355.24081-1-m.grzeschik@pengutronix.de
Cc: Dan Vacura <W36195@motorola.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 09f736aa95476631227d2dc0e6b9aeee1ad7ed58 upstream.
Turns out some xHC controllers require all 64 bits in the CRCR register
to be written to execute a command abort.
The lower 32 bits containing the command abort bit is written first.
In case the command ring stops before we write the upper 32 bits then
hardware may use these upper bits to set the commnd ring dequeue pointer.
Solve this by making sure the upper 32 bits contain a valid command
ring dequeue pointer.
The original patch that only wrote the first 32 to stop the ring went
to stable, so this fix should go there as well.
Fixes: ff0e50d3564f ("xhci: Fix command ring pointer corruption while aborting a command")
Cc: stable@vger.kernel.org
Tested-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211126122340.1193239-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6cca13de26eea6d32a98d96d916a048d16a12822 upstream.
Fix the circular lock dependency and unbalanced unlock of addess0_mutex
introduced when fixing an address0_mutex enumeration retry race in commit
ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Make sure locking order between port_dev->status_lock and address0_mutex
is correct, and that address0_mutex is not unlocked in hub_port_connect
"done:" codepath which may be reached without locking address0_mutex
Fixes: 6ae6dc22d2d1 ("usb: hub: Fix usb enumeration issue due to address0 race")
Cc: <stable@vger.kernel.org>
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211123101656.1113518-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 6ae6dc22d2d1ce6aa77a6da8a761e61aca216f8b upstream.
xHC hardware can only have one slot in default state with address 0
waiting for a unique address at a time, otherwise "undefined behavior
may occur" according to xhci spec 5.4.3.4
The address0_mutex exists to prevent this across both xhci roothubs.
If hub_port_init() fails, it may unlock the mutex and exit with a xhci
slot in default state. If the other xhci roothub calls hub_port_init()
at this point we end up with two slots in default state.
Make sure the address0_mutex protects the slot default state across
hub_port_init() retries, until slot is addressed or disabled.
Note, one known minor case is not fixed by this patch.
If device needs to be reset during resume, but fails all hub_port_init()
retries in usb_reset_and_verify_device(), then it's possible the slot is
still left in default state when address0_mutex is unlocked.
Cc: <stable@vger.kernel.org>
Fixes: 638139eb95 ("usb: hub: allow to process more usb hub events in parallel")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211115221630.871204-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 362468830dd5bea8bf6ad5203b2ea61f8a4e8288 upstream.
The code that enables either BC_LVL or COMP_CHNG interrupt in tcpm_set_cc
wrongly assumes that the interrupt is unmasked by writing 1 to the apropriate
bit in the mask register. In fact, interrupts are enabled when the mask
is 0, so the tcpm_set_cc enables interrupt for COMP_CHNG when it expects
BC_LVL interrupt to be enabled.
This causes inability of the driver to recognize cable unplug events
in host mode (unplug is recognized only via a COMP_CHNG interrupt).
In device mode this bug was masked by simultaneous triggering of the VBUS
change interrupt, because of loss of VBUS when the port peer is providing
power.
Fixes: 48242e3053 ("usb: typec: fusb302: Revert "Resolve fixed power role contract setup"")
Cc: stable <stable@vger.kernel.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Ondrej Jirman <megous@megous.com>
Link: https://lore.kernel.org/r/20211108102833.2793803-1-megous@megous.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d4d2e5329ae9dfd6742c84d79f7d143d10410f1b upstream.
If the first call to devm_usb_get_phy_by_phandle(dev, "fsl,usbphy", 0)
fails with something other than -ENODEV then it leads to an error
pointer dereference. For those errors we should just jump directly to
the error handling.
Fixes: 8253a34bfae3 ("usb: chipidea: ci_hdrc_imx: Also search for 'phys' phandle")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20211117074923.GF5237@kili
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 26288448120b28af1dfd85a6fa6b6d55a16c7f2f upstream.
In the endpoint interrupt functions
dwc3_gadget_endpoint_transfer_in_progress() and
dwc3_gadget_endpoint_trbs_complete() will dereference the endpoint
descriptor. But it could be cleared in __dwc3_gadget_ep_disable()
when accessory disconnected. So we need to check whether it is null
or not before dereferencing it.
Fixes: f09ddcfcb8c5 ("usb: dwc3: gadget: Prevent EP queuing while stopping transfers")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Jack Pham <quic_jackp@quicinc.com>
Signed-off-by: Albert Wang <albertccwang@google.com>
Link: https://lore.kernel.org/r/20211109092642.3507692-1-albertccwang@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 63c4c320ccf77074ffe9019ac596603133c1b517 upstream.
The programming guide noted that the driver needs to verify if the link
state is in U0 before executing the Start Transfer command. If it's not
in U0, the driver needs to perform remote wakeup. This is not accurate.
If the link state is in U1/U2, then the controller will not respond to
link recovery request from DCTL.ULSTCHNGREQ. The Start Transfer command
will trigger a link recovery if it is in U1/U2. A clarification will be
added to the programming guide for all controller versions.
The current implementation shouldn't cause any functional issue. It may
occasionally report an invalid time out warning from failed link
recovery request. The driver will still go ahead with the Start Transfer
command if the remote wakeup fails. The new change only initiates remote
wakeup where it is needed, which is when the link state is in L1/L2/U3.
Fixes: c36d8e947a ("usb: dwc3: gadget: put link to U0 before Start Transfer")
Cc: <stable@vger.kernel.org>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/05b4a5fbfbd0863fc9b1d7af934a366219e3d0b4.1635204761.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
