[ Upstream commit 9b87162de8be26bf3156460b37deee6399fd0fcb ]
Only CS7 and CS8 seem supported but CSIZE is not sanitized from
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: 1da177e4c3 (Linux-2.6.12-rc2)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 87b8061bad9bd4b549b2daf36ffbaa57be2789a2 ]
This fixes two issues that cause the sysrq sequence to be inadvertently
aborted on SCIF serial consoles:
- a NUL character remains in the RX queue after a break has been detected,
which is then passed on to uart_handle_sysrq_char()
- the break interrupt is handled twice on controllers with multiplexed ERI
and BRI interrupts
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210816162201.28801-1-uli+renesas@fpond.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 08a84410a04f05c7c1b8e833f552416d8eb9f6fe upstream.
Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following
message is possible output when system enters suspend and while
transferring data, because clearing TIE bit in SCSCR is not able to
stop any dmaengine transfer.
sh-sci e6550000.serial: ttySC1: Unable to drain transmitter
Note that this driver has already used some #ifdef in the .c file
so that this patch also uses #ifdef to fix the issue. Otherwise,
build errors happens if the CONFIG_SERIAL_SH_SCI_DMA is disabled.
Fixes: 73a19e4c03 ("serial: sh-sci: Add DMA support.")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210610110806.277932-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2ea2e019c190ee3973ef7bcaf829d8762e56e635 upstream.
The Receive FIFO Data Count Trigger field (RTRG[6:0]) in the Receive
FIFO Data Count Trigger Register (HSRTRGR) of HSCIF can only hold values
ranging from 0-127. As the FIFO size is equal to 128 on HSCIF, the user
can write an out-of-range value, touching reserved bits.
Fix this by limiting the trigger value to the FIFO size minus one.
Reverse the order of the checks, to avoid rx_trig becoming zero if the
FIFO size is one.
Note that this change has no impact on other SCIF variants, as their
maximum supported trigger value is lower than the FIFO size anyway, and
the code below takes care of enforcing these limits.
Fixes: a380ed461f ("serial: sh-sci: implement FIFO threshold register setting")
Reported-by: Linh Phung <linh.phung.jy@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/5eff320aef92ffb33d00e57979fd3603bbb4a70f.1620648218.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty/serial driver updates from Greg KH:
"Here are the big set of tty and serial driver updates for 5.6-rc1
Included in here are:
- dummy_con cleanups (touches lots of arch code)
- sysrq logic cleanups (touches lots of serial drivers)
- samsung driver fixes (wasn't really being built)
- conmakeshash move to tty subdir out of scripts
- lots of small tty/serial driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (140 commits)
tty: n_hdlc: Use flexible-array member and struct_size() helper
tty: baudrate: SPARC supports few more baud rates
tty: baudrate: Synchronise baud_table[] and baud_bits[]
tty: serial: meson_uart: Add support for kernel debugger
serial: imx: fix a race condition in receive path
serial: 8250_bcm2835aux: Document struct bcm2835aux_data
serial: 8250_bcm2835aux: Use generic remapping code
serial: 8250_bcm2835aux: Allocate uart_8250_port on stack
serial: 8250_bcm2835aux: Suppress register_port error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Suppress clk_get error on -EPROBE_DEFER
serial: 8250_bcm2835aux: Fix line mismatch on driver unbind
serial_core: Remove unused member in uart_port
vt: Correct comment documenting do_take_over_console()
vt: Delete comment referencing non-existent unbind_con_driver()
arch/xtensa/setup: Drop dummy_con initialization
arch/x86/setup: Drop dummy_con initialization
arch/unicore32/setup: Drop dummy_con initialization
arch/sparc/setup: Drop dummy_con initialization
arch/sh/setup: Drop dummy_con initialization
arch/s390/setup: Drop dummy_con initialization
...
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)
In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-42-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SuperH is the only user of the current implementation of early platform
device support. We want to introduce a more robust approach to early
probing. As the first step - move all the current early platform code
to arch/sh.
In order not to export internal drivers/base functions to arch code for
this temporary solution - copy the two needed routines for driver
matching from drivers/base/platform.c to arch/sh/drivers/platform_early.c.
Also: call early_platform_cleanup() from subsys_initcall() so that it's
called after all early devices are probed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Rich Felker <dalias@libc.org>
Link: https://lore.kernel.org/r/20191003092913.10731-2-brgl@bgdev.pl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As platform_get_irq() now prints an error when the interrupt does not
exist, scary warnings may be printed for optional interrupts:
sh-sci e6550000.serial: IRQ index 1 not found
sh-sci e6550000.serial: IRQ index 2 not found
sh-sci e6550000.serial: IRQ index 3 not found
sh-sci e6550000.serial: IRQ index 4 not found
sh-sci e6550000.serial: IRQ index 5 not found
Fix this by calling platform_get_irq_optional() instead for all but the
first interrupts, which are optional.
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191001180743.1041-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1d267ea653 ("serial: mctrl-gpio: simplify init
routine"), mctrl_gpio_init() returns failure if the assignment to any
member of the gpio array results in an error pointer.
Since commit c359522194593815 ("serial: mctrl_gpio: Avoid probe failures
in case of missing gpiolib"), mctrl_gpio_to_gpiod() returns NULL in the
!CONFIG_GPIOLIB case.
Hence there is no longer a need to check for mctrl_gpio_to_gpiod()
returning an error value. A simple NULL check is sufficient.
This follows the spirit of commit 445df7ff3f ("serial: mctrl-gpio:
drop usages of IS_ERR_OR_NULL") in the mctrl-gpio core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20190814092924.13857-4-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When uart_flush_buffer() is called, the .flush_buffer() callback zeroes
the tx_dma_len field. This may race with the work queue function
handling transmit DMA requests:
1. If the buffer is flushed before the first DMA API call,
dmaengine_prep_slave_single() may be called with a zero length,
causing the DMA request to never complete, leading to messages
like:
rcar-dmac e7300000.dma-controller: Channel Address Error happen
and, with debug enabled:
sh-sci e6e88000.serial: sci_dma_tx_work_fn: ffff800639b55000: 0...0, cookie 126
and DMA timeouts.
2. If the buffer is flushed after the first DMA API call, but before
the second, dma_sync_single_for_device() may be called with a zero
length, causing the transmit data not to be flushed to RAM, and
leading to stale data being output.
Fix this by:
1. Letting sci_dma_tx_work_fn() return immediately if the transmit
buffer is empty,
2. Extending the critical section to cover all DMA preparational work,
so tx_dma_len stays consistent for all of it,
3. Using local copies of circ_buf.head and circ_buf.tail, to make sure
they match the actual operation above.
Reported-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Suggested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Link: https://lore.kernel.org/r/20190624123540.20629-2-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are several issues with the formula used for calculating the
deviation from the intended rate:
1. While min_err and last_stop are signed, srr and baud are unsigned.
Hence the signed values are promoted to unsigned, which will lead
to a bogus value of deviation if min_err is negative,
2. Srr is the register field value, which is one less than the actual
sampling rate factor,
3. The divisions do not use rounding.
Fix this by casting unsigned variables to int, adding one to srr, and
using a single DIV_ROUND_CLOSEST().
Fixes: 63ba1e00f1 ("serial: sh-sci: Support for HSCIF RX sampling point adjustment")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We disable transmission interrupt (clear SCSCR_TIE) after all data has been transmitted
(if uart_circ_empty(xmit)). While transmitting, if the data is still in the tty buffer,
re-enable the SCSCR_TIE bit, which was done at sci_start_tx().
This is unnecessary processing, wasting CPU operation if the data transmission length is large.
And further, transmit end, FIFO empty bits disabling have also been performed in the step above.
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since IRQs might be muxed on some parts, we need to pay attention when we
are freeing them.
Otherwise we get the ugly WARNING "Trying to free already-free IRQ 20".
Fixes: 628c534ae7 ("serial: sh-sci: Improve support for separate TEI and DRI interrupts")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When submitting a DMA request fails in sci_dma_rx_complete(), the driver
tries to fall back to PIO, but that does not work: no more data will be
received, or the kernel will even crash.
Fix this similar as in (but not identical to) sci_submit_rx():
- On SCIF, PIO cannot take over if any DMA transactions are pending,
hence they must be terminated first.
- All active cookies must be invalidated, else rx_timer_fn() may
trigger a NULL pointer dereference.
- Restarting the port is not needed, as it is already running, but
serial port interrupts must be directed back from the DMA engine to
the CPU.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extract the functionality to direct new serial port interrupts back to
the CPU into its own helper, to prepare for using it from a second
callsite.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The cookies and channel pointer for the DMA receive channel are
invalidated in two places, and one more is planned.
Extract this functionality in a common helper.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On (H)SCIF, sci_submit_rx() is called in the receive interrupt handler.
Hence if DMA submission fails, the interrupt handler should resume
handling reception using PIO, else no more data is received.
Make sci_submit_rx() return an error indicator, so the receive interrupt
handler can act appropriately.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When falling back to PIO, active_rx must be set to a different value
than cookie_rx[i], else sci_dma_rx_find_active() will incorrectly find a
match, leading to a NULL pointer dereference in rx_timer_fn() later.
Use zero instead, which is the same value as after driver
initialization.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some callers of sci_submit_rx() hold the port spinlock, others don't.
During fallback to PIO, the driver needs to obtain the port spinlock.
If the lock was already held, spinlock recursion is detected, causing a
deadlock: BUG: spinlock recursion on CPU#0.
Fix this by adding a flag parameter to sci_submit_rx() for the caller to
indicate the port spinlock is already held, so spinlock recursion can be
avoided.
Move the spin_lock_irqsave() up, so all DMA disable steps are protected,
which is safe as the recently introduced dmaengine_terminate_async() can
be called in atomic context.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull tty/serial fixes from Greg KH:
"Here are some small tty fixes for 4.20-rc2
One of these missed the original 4.19-final release, I missed that I
hadn't done a pull request for it as it was in linux-next and my
branch for a long time, that's my fault.
The others are small, fixing some reported issues and finally fixing
the termios mess for alpha so that glibc has a chance to implement
some missing functionality that has been pending for many years now.
All of these have been in linux-next with no reported issues"
* tag 'tty-4.20-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
serial: sh-sci: Fix could not remove dev_attr_rx_fifo_timeout
arch/alpha, termios: implement BOTHER, IBSHIFT and termios2
termios, tty/tty_baudrate.c: fix buffer overrun
vt: fix broken display when running aptitude
serial: sh-sci: Fix receive on SCIFA/SCIFB variants with DMA
While ptr and port both point to the uart_port structure, the former is
the untyped pointer cookie passed to interrupt handlers.
Use the correctly typed port variable instead, to improve type-safety.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On SCIFA and SCIFB serial ports with DMA support (i.e. some ports on
R-Car Gen2 and RZ/G1 SoCs), receive DMA operations are submitted before
the DMA channel pointer is initialized. Hence this fails, and the
driver tries to fall back to PIO. However, at this early phase in the
initialization sequence, fallback to PIO does not work, leading to a
serial port that cannot receive any data.
Fix this by calling sci_submit_rx() after initialization of the DMA
channel pointer.
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 2c4ee23530 ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all (H)SCIF devices support DMA, and failure to set it up is not
normally a cause for concern. This patch demotes the associated warning to
debug output.
Inspired by BSP patch "sci: sh-sci: Fix transfer sequence of unsupport DMA
transfer" (6beb1f98d3bd30) by Hiromitsu Yamasaki.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2d4dd0da45.
This broke earlycon on all Renesas ARM platforms using a SCIF port for the
serial console (R-Car, RZ/A1, RZ/G1, RZ/G2 SoCs), due to an incorrect value
of port->regshift.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2d4dd0da45.
This broke earlycon on all Renesas ARM platforms using a SCIF port for the
serial console (R-Car, RZ/A1, RZ/G1, RZ/G2 SoCs), due to an incorrect value
of port->regshift.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SCIF versions mux error and break interrupts together and then provide
a separate interrupt ID for just TEI/DRI.
Allow all 6 types of interrupts to be specified via platform data (or DT)
and for any signals that are muxed together (have the same interrupt
number) simply register one handler.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is no more need for SCIx_RZ_SCIFA_REGTYPE now that
SCIx_SH4_SCIF_REGTYPE can provide the same register/address definitions.
Also, R7S9210 no longer needs a special compatible since the standard
"renesas,scif" will work just fine.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some devices with SCIx_SH4_SCIF_REGTYPE have no space between registers.
Use the register area size to determine the spacing between register.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No later code uses the assigned value, so it can be dropped.
Reported-by: Simon Horman <horms@verge.net.au>
Fixes: 2c4ee23530 ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
