commit 7c7f9bc986e698873b489c371a08f206979d06b7 upstream.
When a UART port is newly registered, uart_configure_port() seeks to
deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl.
However a number of UART drivers interpret a set RTS bit as *assertion*
instead of deassertion: Affected drivers include those using
serial8250_em485_config() (except 8250_bcm2835aux.c) and some using
mctrl_gpio (e.g. imx.c).
Since the interpretation of the RTS bit is driver-specific, it is not
suitable as a means to centrally deassert Transmit Enable in the serial
core. Instead, the serial core must call on drivers to deassert it in
their driver-specific way. One way to achieve that is to call
->rs485_config(). It implicitly deasserts Transmit Enable.
So amend uart_configure_port() and uart_resume_port() to invoke
uart_rs485_config(). That allows removing calls to uart_rs485_config()
from drivers' ->probe() hooks and declaring the function static.
Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no
hardware flow control, so the modem control lines are irrelevant and
need not be touched. When leaving RS485 mode, reset the modem control
lines to the state stored in port->mctrl. That way, UARTs which are
muxed between RS485 and RS232 transceivers drive the lines correctly
when switched to RS232. (serial8250_do_startup() historically raises
the OUT1 modem signal because otherwise interrupts are not signaled on
ancient PC UARTs, but I believe that no longer applies to modern,
RS485-capable UARTs and is thus safe to be skipped.)
imx.c modifies port->mctrl whenever Transmit Enable is asserted and
deasserted. Stop it from doing that so port->mctrl reflects the RS232
line state.
8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling
->set_mctrl(). Because that is now a no-op in RS485 mode, amend the
function to call serial8250_em485_stop_tx().
fsl_lpuart.c retrieves and applies the RS485 device tree properties
after registering the UART port. Because applying now happens on
registration in uart_configure_port(), move retrieval of the properties
ahead of uart_add_one_port().
Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-group.com/
Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@ginzinger.com/
Fixes: d3b3404df318 ("serial: Fix incorrect rs485 polarity on uart open")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.1663863805.git.lukas@wunner.de
Signed-off-by: Daisuke Mizobuchi <mizo@atmark-techno.com>
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3ee82c6e41f3d2212647ce0bc5a05a0f69097824 upstream.
Commit 76821e222c ("serial: imx: ensure that RX irqs are off if RX is
off") accidentally enabled overrun interrupts unconditionally when
deferring DMA enable until after the receiver has been enabled during
startup.
Fix this by using the DMA-initialised instead of DMA-enabled flag to
determine whether overrun interrupts should be enabled.
Note that overrun interrupts are already accounted for in
imx_uart_clear_rx_errors() when using DMA since commit 41d98b5da9
("serial: imx-serial - update RX error counters when DMA is used").
Fixes: 76821e222c ("serial: imx: ensure that RX irqs are off if RX is off")
Cc: stable@vger.kernel.org # 4.17
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20220411081957.7846-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 028e083832b06fdeeb290e1e57dc1f6702c4c215 ]
The UCR4_OREN should be disabled before disabling the uart receiver in
.stop_rx() instead of in the .shutdown().
Otherwise, if we have the overrun error during the receiver disable
process, the overrun interrupt will keep trigging until we disable the
OREN interrupt in the .shutdown(), because the ORE status can only be
cleared when read the rx FIFO or reset the controller. Although the
called time between the receiver disable and OREN disable in .shutdown()
is very short, there is still the risk of endless interrupt during this
short period of time. So here change to disable OREN before the receiver
been disabled in .stop_rx().
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211125020349.4980-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Enabling the lock dependency validator has revealed
that the way spinlocks are used in the IMX serial
port could result in a deadlock.
Specifically, imx_uart_int() acquires a spinlock
without disabling the interrupts, meaning that another
interrupt could come along and try to acquire the same
spinlock, potentially causing the two to wait for each
other indefinitely.
Use spin_lock_irqsave() instead to disable interrupts
upon acquisition of the spinlock.
Fixes: c974991d26 ("tty:serial:imx: use spin_lock instead of spin_lock_irqsave in isr")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sam Nobs <samuel.nobs@taitradio.com>
Link: https://lore.kernel.org/r/1604955006-9363-1-git-send-email-samuel.nobs@taitradio.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IPG clock is disabled at the end of imx_uart_shutdown(); we really
don't want to run any IRQ handlers after this point.
At least on i.MX8MN, the UART will happily continue to generate interrupts
even with its clocks disabled, but in this state, all register writes are
ignored (which will cause the shadow registers to differ from the actual
register values, resulting in all kinds of weirdness).
In a transfer without DMA, this could lead to the following sequence of
events:
- The UART finishes its transmission while imx_uart_shutdown() is run,
triggering the TXDC interrupt (we can trigger this fairly reliably by
writing a single byte to the TTY and closing it right away)
- imx_uart_shutdown() finishes, disabling the UART clocks
- imx_uart_int() -> imx_uart_transmit_buffer() -> imx_uart_stop_tx()
imx_uart_stop_tx() should now clear UCR4_TCEN to disable the TXDC
interrupt, but this register write is ineffective. This results in an
interrupt storm.
To disable all interrupts in the same place, and to avoid setting UCR4
twice, clearing UCR4_OREN is moved below del_timer_sync() as well; this
should be harmless.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200925082412.12960-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch imitates 6e0a5de213 ("serial: 8250: Use hrtimers for
rs485 delays") in replacing the previously used classic timers
with hrtimers. The old way provided a too coarse resolution on
systems with configs of less than 1000 HZ.
Use of hrtimers addresses this and can be easily extended to
support microsecond resolution in future when support
for this arrives upstream.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20200714093012.21621-3-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The AGTIM flag must be cleared explicitly, otherwise the IRQ handler
will be called in an endless loop.
Fortunately, this issue currently doesn't affect mainline kernels in
practice, as the the RX FIFO trigger level is set to 1 in UFCR. When
setting the trigger level to a higher number, the issue is trivially
reproducible by any RX without DMA that doesn't fill the FIFO up to the
configured level.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200528154747.14201-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit a3cb39d258
("serial: core: Allow detach and attach serial device for console")
changed a bit logic behind lock initialization since for most of the console
driver it's supposed to have lock already initialized even if console is not
enabled. However, it's not the case for Freescale IMX console.
Initialize lock explicitly in the ->probe().
Note, there is still an open question should or shouldn't not this driver
register console properly.
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200525105952.13744-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We're about to amend uart_get_rs485_mode() to support a GPIO pin for
rs485 bus termination. Retrieving the GPIO descriptor may fail, so
allow uart_get_rs485_mode() to return an errno and change all callers
to check for failure.
The GPIO descriptor is going to be stored in struct uart_port. Pass
that struct to uart_get_rs485_mode() in lieu of a struct device and
struct serial_rs485, both of which are directly accessible from struct
uart_port.
A few drivers call uart_get_rs485_mode() before setting the struct
device pointer in struct uart_port. Shuffle those calls around where
necessary.
[Heiko Stuebner did the ar933x_uart.c portion, hence his Signed-off-by.]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/271e814af4b0db3bffbbb74abf2b46b75add4516.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The peripheral has support for inverting its input and/or output
signals. This is useful if the hardware flips polarity of the
peripheral's signal, such as swapped +/- pins on an RS-422 transceiver,
or an inverting level shifter. Add support for these control registers
via the device tree binding.
As part of this change, make the writes of the various registers more
uniform by moving the UCR3 block up near the other registers' blocks,
since the INVT bit must be set before enabling the peripheral.
Signed-off-by: George Hilliard <ghilliard@kopismobile.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20200226222319.18383-3-ghilliard@kopismobile.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main irq handler function starts by first masking disabled
interrupts in the status register values to ensure to only handle
enabled interrupts. This is important as when the RX path in the
hardware is disabled reading the RX fifo results in an external abort.
This checking must be done under the port lock, otherwise the following
can happen:
CPU1 | CPU2
|
irq triggers as there are chars |
in the RX fifo |
| grab port lock
imx_uart_int finds RRDY enabled |
and calls imx_uart_rxint which |
has to wait for port lock |
| disable RX (e.g. because we're
| using RS485 with !RX_DURING_TX)
|
| release port lock
read from RX fifo with RX |
disabled => exception |
So take the port lock only once in imx_uart_int() instead of in the
functions called from there.
Reported-by: Andre Renaud <arenaud@designa-electronics.com>
Cc: stable@vger.kernel.org
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20200121071702.20150-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All i.MX SoCs except i.MX1 have ONLY one necessary IRQ, use
platform_get_irq_optional() to get second/third IRQ which are
optional to avoid below error message during probe:
[ 0.726219] imx-uart 30860000.serial: IRQ index 1 not found
[ 0.731329] imx-uart 30860000.serial: IRQ index 2 not found
Fixes: 7723f4c5ec ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1570614559-11900-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using only 4 DMA periods for UART RX is very few if we have a high
frequency of small transfers - like in our case using Bluetooth with
many small packets via UART - causing many dma transfers but in each
only filling a fraction of a single buffer. Such a case may lead to
the situation that DMA RX transfer is triggered but no free buffer is
available. When this happens dma channel ist stopped - with the patch
"dmaengine: imx-sdma: fix dma freezes" temporarily only - with the
possible consequences that:
with disabled hw flow control:
If enough data is incoming on UART port the RX FIFO runs over and
characters will be lost. What then happens depends on upper layer.
with enabled hw flow control:
If enough data is incoming on UART port the RX FIFO reaches a level
where CTS is deasserted and remote device sending the data stops.
If it fails to stop timely the i.MX' RX FIFO may run over and data
get lost. Otherwise it's internal TX buffer may getting filled to
a point where it runs over and data is again lost. It depends on
the remote device how this case is handled and if it is recoverable.
Obviously we want to avoid having no free buffers available. So we
decrease the size of the buffers and increase their number and the
total buffer size.
Signed-off-by: Philipp Puschmann <philipp.puschmann@emlix.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20190923135916.1212-1-philipp.puschmann@emlix.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_set_termios(): avoid writing baud rate divider registers when the
values to be written are the same as current. Any writing seems to
restart transmission/receiving logic in the hardware, that leads to
data breakage even when rate doesn't in fact change. E.g., user
switches RTS/CTS handshake and suddenly gets broken bytes.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-5-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_set_termios(): stopping receiver and transmitter does harm when
something that doesn't touch transmission format/rate changes, such as
RTS/CTS handshake.
OTOH, it does no good on baud rate or format change, as
synchronization on upper-level protocols is still required to do it
right.
Therefore, just stop doing it.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Link: https://lore.kernel.org/r/1567017475-11919-3-git-send-email-sorganov@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
imx_uart_set_termios() called imx_uart_rts_active(), or
imx_uart_rts_inactive() before taking port->port.lock.
As a consequence, sport->port.mctrl that these functions modify
could have been changed without holding port->port.lock.
Moved locking of port->port.lock above the calls to fix the issue.
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_info() is more appropriate for printing messages inside drivers, so
switch to dev_info().
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Each time the DMA engine signals a transaction error the driver prints
a message at error level. Getting transaction errors is pretty much
expected on baudrate mismatches and the correspoding error counters
are increased in this case properly. Remove the error message which
is possibly repeated at a very high rate which can lock up the whole
system.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ipg clock only needs to be unprepared in case preparing
per clock fails. The ipg clock has already disabled at the point.
Fixes: 1cf93e0d54 ("serial: imx: remove the uart_console() check")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some i.MX SoCs' low power mode, such as i.MX7D's LPSR(low power
state retention), UART iomux settings will be lost, need to add
pinctrl sleep/default mode switch during suspend/resume to make
sure UART iomux settings are correct after resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In noirq suspend/resume stage with no_console_suspend enabled,
imx_uart_console_write() may be called to print out log_buf
message by printk(), so there will be race condition between
imx_uart_console_write() and imx_uart_save/restore_context(),
need to add lock to protect the registers save/restore operations.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before the program enters the uart ISR, the local interrupt has been
disabled by the system, so it's not appropriate to use spin_lock_irqsave
interface in the ISR.
Signed-off-by: jun qian <hangdianqj@163.com>
Reviewed-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Correct to check the right rx dma cookie status in spit of it
works because only one cookie is running in the current sdma.
But it will not once sdma driver support multi cookies
running based on virt-dma.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Initially when register shadowing was introduced (commit 3a0ab62f43
("serial: imx: implement shadow registers for UCRx and UFCR")) the logic
to handle UCR2_SRST was wrong but documented consistently. Later the
handling was fixed, but the comment was not. This change makes up leeway
for the latter.
Fixes: 0aa821d846 ("serial: imx: fix cached UCR2 read on software reset")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
