This adds SPI support for the Sparx5 SoC, which is using the MMIO
Designware SPI controller.
The Sparx5 differs from the Ocelot version in these areas:
* The CS override is controlled by a new set of registers for
this purpose.
* The Sparx5 SPI controller has the RX sample delay register, and it
must be configured for the (SPI NAND) device on SPI2.
* The Sparx5 SPI controller has 2 different SPI bus interfaces on the
same controller (don't ask...). The "spi-mux" driver should be used
in conjunction with the SPI driver to select the appropriate bus.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200824203010.2033-3-lars.povlsen@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
This add support for the RX_SAMPLE_DLY register. If enabled in the
Designware IP, it allows tuning of the rx data signal by means of an
internal rx sample fifo.
The register is controlled by the rx-sample-delay-ns DT property,
which is defined per SPI slave as well on controller level.
The controller level rx-sample-delay-ns will apply to all slaves
without the property explicitly defined.
The register is located at offset 0xf0, and if the option is not
enabled in the IP, changing the register will have no effect. The
register will only be written if any slave defines a nonzero value
(after scaling by the clock period).
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200824203010.2033-2-lars.povlsen@microchip.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Buffers need to mapped to DMA channel's device pointer instead of SPI
controller's device pointer as its system DMA that actually does data
transfer.
Data inconsistencies have been reported when reading from flash
without this fix.
Fixes: ffa639e069 ("mtd: spi-nor: cadence-quadspi: Add DMA support for direct mode reads")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/20200831130720.4524-1-vigneshr@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The 'spi_stm32 44004000.spi: Communication suspended' message means that
when using PIO, the kernel did not read the FIFO fast enough and so the
SPI controller paused the transfer. Currently, this is printed on every
single such event, so if the kernel is busy and the controller is pausing
the transfers often, the kernel will be all the more busy scrolling this
message into the log buffer every few milliseconds. That is not helpful.
Instead, rate-limit the message and print it every once in a while. It is
not possible to use the default dev_warn_ratelimited(), because that is
still too verbose, as it prints 10 lines (DEFAULT_RATELIMIT_BURST) every
5 seconds (DEFAULT_RATELIMIT_INTERVAL). The policy here is to print 1 line
every 50 seconds (DEFAULT_RATELIMIT_INTERVAL * 10), because 1 line is more
than enough and the cycles saved on printing are better left to the CPU to
handle the SPI. However, dev_warn_once() is also not useful, as the user
should be aware that this condition is possibly recurring or ongoing. Thus
the custom rate-limit policy.
Finally, turn the message from dev_warn() to dev_dbg(), since the system
does not suffer any sort of malfunction if this message appears, it is
just slowing down. This further reduces the printing into the log buffer
and frees the CPU to do useful work.
Fixes: dcbe0d84df ("spi: add driver for STM32 SPI controller")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Antonio Borneo <borneo.antonio@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200905151913.117775-1-marex@denx.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The "tx/rx-transfer - crossing PAGE_SIZE" test always fails when
len=131071 and rx_offset >= 5:
spi-loopback-test spi0.0: Running test tx/rx-transfer - crossing PAGE_SIZE
...
with iteration values: len = 131071, tx_off = 0, rx_off = 3
with iteration values: len = 131071, tx_off = 0, rx_off = 4
with iteration values: len = 131071, tx_off = 0, rx_off = 5
loopback strangeness - rx changed outside of allowed range at: ...a4321000
spi_msg@ffffffd5a4157690
frame_length: 131071
actual_length: 131071
spi_transfer@ffffffd5a41576f8
len: 131071
tx_buf: ffffffd5a4340ffc
Note that rx_offset > 3 can only occur if the SPI controller driver sets
->dma_alignment to a higher value than 4, so most SPI controller drivers
are not affect.
The allocated Rx buffer is of size SPI_TEST_MAX_SIZE_PLUS, which is 132
KiB (assuming 4 KiB pages). This test uses an initial offset into the
rx_buf of PAGE_SIZE - 4, and a len of 131071, so the range expected to
be written in this transfer ends at (4096 - 4) + 5 + 131071 == 132 KiB,
which is also the end of the allocated buffer. But the code which
verifies the content of the buffer reads a byte beyond the allocated
buffer and spuriously fails because this out-of-bounds read doesn't
return the expected value.
Fix this by using ITERATE_LEN instead of ITERATE_MAX_LEN to avoid
testing sizes which cause out-of-bounds reads.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Link: https://lore.kernel.org/r/20200902132341.7079-1-vincent.whitchurch@axis.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Hi Mark,
This patch series contains several improvements for the Renesas SPI/QSPI
driver related to bit rate configuration.
Changes compared to v1
(https://lore.kernel.org/r/20200608095940.30516-1-geert+renesas@glider.be):
- Drop accepted patch.
This has been tested on RSK+RZA1 (RSPI) and R-Car M2-W/Koelsch (QSPI),
using a scope and logic analyzer, except for the by-one divider on QSPI.
This has not been tested on legacy SuperH, due to lack of hardware.
Thanks for your comments!
Geert Uytterhoeven (7):
spi: rspi: Remove useless .set_config_register() check
spi: rspi: Clean up Bit Rate Division Setting handling
spi: rspi: Increase bit rate accuracy on RZ/A
spi: rspi: Increase bit rate range for RSPI on SH
spi: rspi: Increase bit rate range for QSPI
spi: rspi: Fill in spi_transfer.effective_speed_hz
spi: rspi: Fill in controller speed limits
drivers/spi/spi-rspi.c | 81 +++++++++++++++++++++++++++---------------
1 file changed, 52 insertions(+), 29 deletions(-)
--
2.17.1
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Increase bit rate range for QSPI by extending the range of supported
dividers:
1. QSPI supports a divider of 1, by setting SPBR to zero, increasing
the upper limit from 48.75 to 97.5 MHz on R-Car Gen2,
2. Make use of the Bit Rate Frequency Division Setting field in
Command Registers, to decrease the lower limit from 191 to 24 kbps
on R-Car Gen2.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819125904.20938-6-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
rspi_rz_set_config_register() favors high values of "brdv" over high
values of "spbr". As "brdv" is not a plain divider, but controls a
power-of-two divider, this may cause the selection of non-optimal
divider values. E.g. on RSK+RZA1, when 3.8 MHz is requested, the actual
configured bit rate is 2.08 MHz (spbr = 1, brdv = 3), while 3.7 MHz
would be possible (spbr = 8, brdv = 0).
Fix this by only resorting to higher "brdv" values when really needed.
This makes the driver always pick optimal divider values on RZ/A.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200819125904.20938-4-geert+renesas@glider.be
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQ_EINT0 constant is a platform detail that is
defined in mach/irqs.h and not visible to drivers once
that header is made private.
Since the same calculation already happens in s3c24xx_set_fiq,
just return the value from there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-31-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The fiq handler needs access to some register definitions that
should not be used directly by device drivers.
Since this is closely related to the irqchip driver anyway,
move it into the same place.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[krzk: Add a header guard in include/linux/spi/s3c24xx-fiq.h, fix
SPDX comment style, update maintainer's entry]
Co-developed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-23-krzk%40kernel.org
Acked-by: Mark Brown <broonie@kernel.org>
Pull spi fixes from Mark Brown:
"A bunch of fixes that came in for SPI during the merge window.
Some from ST and others for their controller, one from Lukas for a
race between device addition and controller unregistration and one
from fix from Geert for the DT bindings which unbreaks validation"
* tag 'spi-fix-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
dt-bindings: lpspi: Add missing boolean type for fsl,spi-only-use-cs1-sel
spi: stm32: always perform registers configuration prior to transfer
spi: stm32: fixes suspend/resume management
spi: stm32: fix stm32_spi_prepare_mbr in case of odd clk_rate
spi: stm32: fix fifo threshold level in case of short transfer
spi: stm32h7: fix race condition at end of transfer
spi: stm32: clear only asserted irq flags on interrupt
spi: Prevent adding devices below an unregistering controller
The caller of stm32_spi_transfer_one(), spi_transfer_one_message(),
is waiting for us to call spi_finalize_current_transfer() and will
eventually schedule a new transfer, if available.
We should guarantee that the spi controller is really available
before calling spi_finalize_current_transfer().
Move the call to spi_finalize_current_transfer() _after_ the call
to stm32_spi_disable().
Signed-off-by: Antonio Borneo <antonio.borneo@st.com>
Signed-off-by: Alain Volmat <alain.volmat@st.com>
Link: https://lore.kernel.org/r/1597043558-29668-2-git-send-email-alain.volmat@st.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull sound updates from Takashi Iwai:
"This became wide and scattered updates all over the sound tree as
diffstat shows: lots of (still ongoing) refactoring works in ASoC,
fixes and cleanups caught by static analysis, inclusive term
conversions as well as lots of new drivers. Below are highlights:
ASoC core:
- API cleanups and conversions to the unified mute_stream() call
- Simplify I/O helper functions
- Use helper macros to retrieve RTD from substreams
ASoC drivers:
- Lots of fixes and cleanups in Intel ASoC drivers
- Lots of new stuff: Freescale MQS and i.MX6sx, Intel KeemBay I2S,
Maxim MAX98360A and MAX98373 SoundWire, various Mediatek boards,
nVidia Tegra 186 and 210, RealTek RL6231, Samsung Midas and Aries
boards, TI J721e EVM
ALSA core:
- Minor code refacotring for SG-buffer handling
HD-audio:
- Generalization of mute-LED handling with LED classdev
- Intel silent stream support for HDMI
- Device-specific fixes: CA0132, Loongson-3
Others:
- Usual USB- and HD-audio quirks for various devices
- Fixes for echoaudio DMA position handling
- Various documents and trivial fixes for sparse warnings
- Conversion to adopt inclusive terms"
* tag 'sound-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (479 commits)
ALSA: pci: delete repeated words in comments
ALSA: isa: delete repeated words in comments
ALSA: hda/tegra: Add 100us dma stop delay
ALSA: hda: Add dma stop delay variable
ASoC: hda/tegra: Set buffer alignment to 128 bytes
ALSA: seq: oss: Serialize ioctls
ALSA: hda/hdmi: Add quirk to force connectivity
ALSA: usb-audio: add startech usb audio dock name
ALSA: usb-audio: Add support for Lenovo ThinkStation P620
Revert "ALSA: hda: call runtime_allow() for all hda controllers"
ALSA: hda/ca0132 - Fix AE-5 microphone selection commands.
ALSA: hda/ca0132 - Add new quirk ID for Recon3D.
ALSA: hda/ca0132 - Fix ZxR Headphone gain control get value.
ALSA: hda/realtek: Add alc269/alc662 pin-tables for Loongson-3 laptops
ALSA: docs: fix typo
ALSA: doc: use correct config variable name
ASoC: core: Two step component registration
ASoC: core: Simplify snd_soc_component_initialize declaration
ASoC: core: Relocate and expose snd_soc_component_initialize
ASoC: sh: Replace 'select' DMADEVICES 'with depends on'
...
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
Previously the stm32h7 interrupt thread cleared all non-masked interrupts.
If an interrupt was to occur during the handling of another interrupt its
flag would be unset, resulting in a lost interrupt.
This patches fixes the issue by clearing only the currently set interrupt
flags.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Link: https://lore.kernel.org/r/20200804195136.1485392-1-t.schramm@manjaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, nothing really going on in the core
although there's been quite a bit of driver related activity.
This includes the addition of some shared code in drivers/memory for
the Renesas RPC-IF which is used by a newly added SPI driver, the
memory subsystem doesn't seem to have a fixed maintainer at the minute
and this seemed like the most sensible way to get that hardware
supported.
- Quite a few cleanups and optimizations for the Altera, Qualcomm
GENI, sun6i and lantiq drivers.
- Several more GPIO descriptor conversions.
- Move the Cadence QuadSPI driver from drivers/mtd to drivers/spi.
- New support for Mediatek MT8192 and Renesas RPC-IF, R8A7742 and
R8A774e1"
* tag 'spi-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (119 commits)
dt-bindings: lpspi: New property in document DT bindings for LPSPI
spi: lpspi: fix using CS discontinuously on i.MX8DXLEVK
spi: lpspi: remove unused fsl_lpspi->chipselect
spi: lpspi: Fix kernel warning dump when probe fail after calling spi_register
spi: rockchip: Fix error in SPI slave pio read
spi: rockchip: Support 64-location deep FIFOs
spi: rockchip: Config spi rx dma burst size depend on xfer length
spi: spi-topcliff-pch: drop call to wakeup-disable
spi: spidev: Align buffers for DMA
spi: correct kernel-doc inconsistency
spi: sun4i: update max transfer size reported
spi: imx: enable runtime pm support
spi: update bindings for MT8192 SoC
spi: mediatek: add spi support for mt8192 IC
spi: Add bindings for Lightning Mountain SoC
spi: lantiq: Add support to Lightning Mountain SoC
spi: lantiq: Move interrupt configuration to SoC specific data structure
spi: lantiq: Add fifo size bit mask in SoC specific data structure
spi: lantiq: Add support to acknowledge interrupt
spi: lantiq: Move interrupt control register offesets to SoC specific data structure
...
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
CONFIG_OF_DYNAMIC and CONFIG_ACPI allow adding SPI devices at runtime
using a DeviceTree overlay or DSDT patch. CONFIG_SPI_SLAVE allows the
same via sysfs.
But there are no precautions to prevent adding a device below a
controller that's being removed. Such a device is unusable and may not
even be able to unbind cleanly as it becomes inaccessible once the
controller has been torn down. E.g. it is then impossible to quiesce
the device's interrupt.
of_spi_notify() and acpi_spi_notify() do hold a ref on the controller,
but otherwise run lockless against spi_unregister_controller().
Fix by holding the spi_add_lock in spi_unregister_controller() and
bailing out of spi_add_device() if the controller has been unregistered
concurrently.
Fixes: ce79d54ae4 ("spi/of: Add OF notifier handler")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.19+
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Link: https://lore.kernel.org/r/a8c3205088a969dc8410eec1eba9aface60f36af.1596451035.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
