[ Upstream commit 3b384cc74b00b5ac21d18e4c1efc3c1da5300971 ]
Looks like the driver sleep pins configuration is unusable. Adding the
sleep pins causes the usb phy to not respond. We need to use the default
pins in probe, and only set sleep pins at phy_mdm6600_device_power_off().
As the modem can also be booted to a serial port mode for firmware
flashing, let's make the pin changes limited to probe and remove. For
probe, we get the default pins automatically. We only need to set the
sleep pins in phy_mdm6600_device_power_off() to prevent the modem from
waking up because the gpio line glitches.
If it turns out that we need a separate state for phy_mdm6600_power_on()
and phy_mdm6600_power_off(), we can use the pinctrl idle state.
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Fixes: 2ad2af0816 ("phy: mapphone-mdm6600: Improve phy related runtime PM calls")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230913060433.48373-3-tony@atomide.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19a1d46bd699940a496d3b0d4e142ef99834988c ]
inno_write is used to configure 0xaa reg, that also hold the
POST_PLL_POWER_DOWN bit.
When POST_PLL_REFCLK_SEL_TMDS is configured the power down bit is not
taken into consideration.
Fix this by keeping the power down bit until configuration is complete.
Also reorder the reg write order for consistency.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-5-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d5ef343c1d62bc4c4c2c393af654a41cb34b449f ]
inno_hdmi_phy_rk3328_clk_recalc_rate() is returning a rate not found
in the pre pll config table when the fractal divider is used.
This can prevent proper power_on because a tmdsclock for the new rate
is not found in the pre pll config table.
Fix this by saving and returning a rounded pixel rate that exist
in the pre pll config table.
Fixes: 53706a1168 ("phy: add Rockchip Innosilicon hdmi phy")
Signed-off-by: Zheng Yang <zhengyang@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Link: https://lore.kernel.org/r/20230615171005.2251032-3-jonas@kwiboo.se
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 13c088cf3657d70893d75cf116be937f1509cc0f ]
The size of array 'priv->ports[]' is INNO_PHY_PORT_NUM.
In the for loop, 'i' is used as the index for array 'priv->ports[]'
with a check (i > INNO_PHY_PORT_NUM) which indicates that
INNO_PHY_PORT_NUM is allowed value for 'i' in the same loop.
This > comparison needs to be changed to >=, otherwise it potentially leads
to an out of bounds write on the next iteration through the loop
Fixes: ba8b0ee81f ("phy: add inno-usb2-phy driver for hi3798cv200 SoC")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20230721090558.3588613-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 8a0eb8f9b9a002291a3934acfd913660b905249e ]
The driver is not enabling the ref clock, which thus gets disabled by
the clk_disable_unused() initcall. This leads to the dwc3 controller
failing to initialize if probed after clk_disable_unused() is called,
for instance when the driver is built as a module.
To fix this, switch to the clk_bulk API to handle both cfg_ahb and ref
clocks at the proper places.
Note that the cfg_ahb clock is currently not used by any device tree
instantiation of the PHY. Work needs to be done separately to fix this.
Link: https://lore.kernel.org/linux-arm-msm/ZEqvy+khHeTkC2hf@fedora/
Fixes: 51e8114f80 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-3-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45d89a344eb46db9dce851c28e14f5e3c635c251 ]
In the dwc3 core, both system and runtime suspend end up calling
dwc3_suspend_common(). From there, what happens for the PHYs depends on
the USB mode and whether the controller is entering system or runtime
suspend.
HOST mode:
(1) system suspend on a non-wakeup-capable controller
The [1] if branch is taken. dwc3_core_exit() is called, which ends up
calling phy_power_off() and phy_exit(). Those two functions decrease the
PM runtime count at some point, so they will trigger the PHY runtime
sleep (assuming the count is right).
(2) runtime suspend / system suspend on a wakeup-capable controller
The [1] branch is not taken. dwc3_suspend_common() calls
phy_pm_runtime_put_sync(). Assuming the ref count is right, the PHY
runtime suspend op is called.
DEVICE mode:
dwc3_core_exit() is called on both runtime and system sleep
unless the controller is already runtime suspended.
OTG mode:
(1) system suspend : dwc3_core_exit() is called
(2) runtime suspend : do nothing
In host mode, the code seems to make a distinction between 1) runtime
sleep / system sleep for wakeup-capable controller, and 2) system sleep
for non-wakeup-capable controller, where phy_power_off() and phy_exit()
are only called for the latter. This suggests the PHY is not supposed to
be in a fully powered-off state for runtime sleep and system sleep for
wakeup-capable controller.
Moreover, downstream, cfg_ahb_clk only gets disabled for system suspend.
The clocks are disabled by phy->set_suspend() [2] which is only called
in the system sleep path through dwc3_core_exit() [3].
With that in mind, don't disable the clocks during the femto PHY runtime
suspend callback. The clocks will only be disabled during system suspend
for non-wakeup-capable controllers, through dwc3_core_exit().
[1] https://elixir.bootlin.com/linux/v6.4/source/drivers/usb/dwc3/core.c#L1988
[2] https://git.codelinaro.org/clo/la/kernel/msm-5.4/-/blob/LV.AU.1.2.1.r2-05300-gen3meta.0/drivers/usb/phy/phy-msm-snps-hs.c#L524
[3] https://git.codelinaro.org/clo/la/kernel/msm-5.4/-/blob/LV.AU.1.2.1.r2-05300-gen3meta.0/drivers/usb/dwc3/core.c#L1915
Signed-off-by: Adrien Thierry <athierry@redhat.com>
Link: https://lore.kernel.org/r/20230629144542.14906-2-athierry@redhat.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 8a0eb8f9b9a0 ("phy: qcom-snps-femto-v2: properly enable ref clock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 668dc8afce43d4bc01feb3e929d6d5ffcb14f899 ]
In the probe path, dev_err() can be replaced with dev_err_probe()
which will check if error code is -EPROBE_DEFER and prints the
error name. It also sets the defer probe reason which can be
checked later through debugfs.
Signed-off-by: Yuan Can <yuancan@huawei.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20220922111228.36355-8-yuancan@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Stable-dep-of: 8a0eb8f9b9a0 ("phy: qcom-snps-femto-v2: properly enable ref clock")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c3966ced8eb8dc53b6c8d7f97d32cc8a2107d83e ]
Smatch reports the following error:
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->cal_clk' from clk_prepare_enable() not released on lines:
58.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->cal_sleep_clk' from clk_prepare_enable() not released on
lines: 58.
drivers/phy/qualcomm/phy-qcom-usb-hsic.c:82 qcom_usb_hsic_phy_power_on()
warn: 'uphy->phy_clk' from clk_prepare_enable() not released on lines:
58.
Fix this by calling proper clk_disable_unprepare calls.
Fixes: 0b56e9a7e8 ("phy: Group vendor specific phy drivers")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20220914051334.69282-1-dzm91@hust.edu.cn
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ce88613e5bd579478653a028291098143f2a5bdf ]
The pm_runtime_enable() will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable().
Add missing pm_runtime_disable() for serdes_am654_probe().
Fixes: 71e2f5c5c2 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220301025853.1911-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d644e0d79829b1b9a14beedbdb0dc1256fc3677d ]
The pm_runtime_enable will increase power disable depth.
If the probe fails, we should use pm_runtime_disable() to balance
pm_runtime_enable(). And use pm_runtime_dont_use_autosuspend() to
undo pm_runtime_use_autosuspend()
In the PM Runtime docs:
Drivers in ->remove() callback should undo the runtime PM changes done
in ->probe(). Usually this means calling pm_runtime_disable(),
pm_runtime_dont_use_autosuspend() etc.
We should do this in error handling.
Fixes: f7f50b2a7b ("phy: mapphone-mdm6600: Add runtime PM support for n_gsm on USB suspend")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220301024615.31899-1-linmq006@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3153fa38e38af566cf6454a03b1dbadaf6f323c0 ]
According to the comment of the function phy_mipi_dphy_get_default_config(),
it uses minimum D-PHY timings based on MIPI D-PHY specification. They are
derived from the valid ranges specified in Section 6.9, Table 14, Page 41
of the D-PHY specification (v1.2). The table 14 explicitly mentions that
the minimum T-LPX parameter is 50 nanoseconds and the minimum TA-SURE
parameter is T-LPX nanoseconds. Likewise, the kernel doc of the 'lpx' and
'ta_sure' members of struct phy_configure_opts_mipi_dphy mentions that
the minimum values are 50000 picoseconds and @lpx picoseconds respectively.
Also, the function phy_mipi_dphy_config_validate() checks if cfg->lpx is
less than 50000 picoseconds and if cfg->ta_sure is less than cfg->lpx,
which hints the same minimum values.
Without this patch, the function phy_mipi_dphy_get_default_config()
wrongly sets cfg->lpx to 60000 picoseconds and cfg->ta_sure to 2 * cfg->lpx.
So, let's correct them to 50000 picoseconds and cfg->lpx respectively.
Note that I've only tested the patch with RM67191 DSI panel on i.MX8mq EVK.
Help is needed to test with other i.MX8mq, Meson and Rockchip platforms,
as I don't have the hardwares.
Fixes: dddc97e823 ("phy: dphy: Add configuration helpers")
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Link: https://lore.kernel.org/r/20220216071257.1647703-1-victor.liu@nxp.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 42fed57046fc74586d7058bd51a1c10ac9c690cb ]
The PHY client driver does a phy_exit() call on suspend or rmmod and
the PHY driver needs to know the difference because some clocks need
to be kept running for suspend but can be shutdown on unbind/rmmod
(or if there are no PHY clients at all).
The fix is to use a PM notifier so the driver can tell if a PHY
client is calling exit() because of a system suspend or a driver
unbind/rmmod.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20211201180653.35097-2-alcooperx@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 37291f60d0822f191748c2a54ce63b0bc669020f ]
TX_PROT_BUS_WIDTH and RX_PROT_BUS_WIDTH are single registers with
separate bit fields for each lane. The code in xpsgtr_phy_init_sgmii was
not preserving the existing register value for other lanes, so enabling
the PHY in SGMII mode on one lane zeroed out the settings for all other
lanes, causing other PS-GTR peripherals such as USB3 to malfunction.
Use xpsgtr_clr_set to only manipulate the desired bits in the register.
Fixes: 4a33bea003 ("phy: zynqmp: Add PHY driver for the Xilinx ZynqMP Gigabit Transceiver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20220126001600.1592218-1-robert.hancock@calian.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b475bf0ec40a2b13fb32ef62f5706576d5858460 ]
The FSEL_MASK which selects the refclock is defined incorrectly.
It should be [4:6] not [5:7]. Due to this incorrect definition, the BIT(7)
in USB2_PHY_USB_PHY_HS_PHY_CTRL_COMMON0 is reset which keeps PHY analog
blocks ON during suspend.
Fix this issue by correctly defining the FSEL_MASK.
Fixes: 51e8114f80 ("phy: qcom-snps: Add SNPS USB PHY driver for QCOM based SOCs")
Signed-off-by: Sandeep Maheswaram <quic_c_sanm@quicinc.com>
Link: https://lore.kernel.org/r/1635135575-5668-1-git-send-email-quic_c_sanm@quicinc.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2f2b73a29d2aabf5ad0150856c3e5cb6e04dcfc1 ]
Since the EMMC clock was changed from 200Mhz to 175Mhz in FIP,
there were some warnings introduced, as the frequency values
being checked was still wrt 200Mhz in code. Hence, the frequency
checks are now updated based on the current 175Mhz EMMC clock changed
in FIP.
Spamming kernel log msg:
"phy phy-20290000.mmc_phy.2: Unsupported rate: 43750000"
Signed-off-by: Rashmi A <rashmi.a@intel.com>
Reviewed-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-By: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20210603182242.25733-3-rashmi.a@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4a90bbb478dbf18ecdec9dcf8eb708e319d24264 ]
The current driver uses a value from register TEST_O as the original
value for register TEST_I, though, the value is overwritten by "param",
so there is a bug that the original value isn't no longer used.
The value of TEST_O[7:0] should be masked with "mask", replaced with
"param", and placed in the bitfield TESTI_DAT_MASK as new TEST_I value.
Fixes: c6d9b13241 ("phy: socionext: add PCIe PHY driver support")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1623037842-19363-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6cb17707aad869de163d7bf42c253caf501be4e2 ]
Merely enabling CONFIG_COMPILE_TEST should not enable additional code.
To fix this, restrict the automatic enabling of ARMADA375_USBCLUSTER_PHY
to MACH_ARMADA_375, and ask the user in case of compile-testing.
Fixes: eee47538ec ("phy: add support for USB cluster on the Armada 375 SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210208150252.424706-1-geert+renesas@glider.be
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e52a39f1942b771213678c56002ce90a2f126d2 ]
commit 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module
present in TI J721E SoC") modeled both MUX clocks and DIVIDER clocks in
wiz. However during cleanup, it removed only the MUX clock provider.
Remove the DIVIDER clock provider here.
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Link: https://lore.kernel.org/r/20210310120840.16447-3-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f7eb147d306ad2efae6837e20d2944f03be42eb4 upstream.
Invoke wiz_init() before configuring anything else in Sierra/Torrent
(invoked as part of of_platform_device_create()). wiz_init() resets the
SERDES device and any configuration done in the probe() of
Sierra/Torrent will be lost. In order to prevent SERDES configuration
from getting reset, invoke wiz_init() immediately before invoking
of_platform_device_create().
Fixes: 091876cc35 ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Swapnil Jakhade <sjakhade@cadence.com>
Cc: <stable@vger.kernel.org> # v5.10
Link: https://lore.kernel.org/r/20210319124128.13308-3-kishon@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
