commit 2542e16c392508800f1d9037feee881a9c444951 upstream.
Qcom PCIe IP version v2.7.0 and its derivatives don't contain the
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT register. Instead, they have the new
PCIE20_PARF_AXI_MSTR_WR_ADDR_HALT_V2 register. So fix the incorrect
register usage which is modifying a different register.
Also in this IP version, this register change doesn't depend on MSI
being enabled. So remove that check also.
Link: https://lore.kernel.org/r/20230316081117.14288-2-manivannan.sadhasivam@linaro.org
Fixes: ed8cc3b1fc ("PCI: qcom: Add support for SDM845 PCIe controller")
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Cc: <stable@vger.kernel.org> # 5.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38f897ae3d44900f627cad708a15db498ce2ca31 ]
We currently enable clocks BEFORE we write to PARF_PHY_CTRL reg to enable
clocks and resets. This causes the driver to never set to a ready state
with the error 'Phy link never came up'.
This is caused by the PHY clock getting enabled before setting the required
bits in the PARF regs.
A workaround for this was set but with this new discovery we can drop
the workaround and use a proper solution to the problem by just enabling
the clock only AFTER the PARF_PHY_CTRL bit is set.
This correctly sets up the PCIe link and makes it usable even when a
bootloader leaves the PCIe link in an undefined state.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Link: https://lore.kernel.org/r/20220708222743.27019-1-ansuelsmth@gmail.com
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
- Make sure PCIe is reset before init to work around QSDK U-Boot issue
(Ansuel Smith)
- Set iproc affinity mask on MSI interrupts (Mark Tomlinson)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Make sure PCIe is reset before init for rev 2.1.0
Currently, there is only a 1 ms sleep after asserting PERST.
Reading the datasheets for different endpoints, some require PERST to be
asserted for 10 ms in order for the endpoint to perform a reset, others
require it to be asserted for 50 ms.
Several SoCs using this driver uses PCIe Mini Card, where we don't know
what endpoint will be plugged in.
The PCI Express Card Electromechanical Specification r2.0, section
2.2, "PERST# Signal" specifies:
"On power up, the deassertion of PERST# is delayed 100 ms (TPVPERL) from
the power rails achieving specified operating limits."
Add a sleep of 100 ms before deasserting PERST, in order to ensure that
we are compliant with the spec.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.5+
The QCS404 platform contains a PCIe version 2.4.0 controller and a
Qualcomm PCIe2 PHY. The driver already supports version 2.4.0, for the
IPQ4019, but this support touches clocks and resets related to the PHY
as well and there's no upstream driver for the PHY.
On QCS404 we must initialize the PHY, so a separate PHY driver is
implemented to take care of this and the controller driver is updated to
not require the PHY related resources. This is done by relying on the
fact that operations in both the clock and reset framework are NOPs when
passed NULL, so we can isolate this change to only the
qcom_pcie_get_resources_2_4_0() function.
For QCS404 we also need to enable the AHB (iface) clock, in order to
access the register space of the controller, but as this is not part of
the IPQ4019 DT binding this is only added for new users of the 2.4.0
controller.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Before introducing the QCS404 platform, which uses the same PCIe
controller as IPQ4019, migrate this to use the bulk clock API, in order
to make the error paths slighly cleaner.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Move the device class fudge to a proper fixup function, and remove
qcom_pcie_rd_own_conf() which has become useless.
dw_pcie_setup_rc() already did the right thing, but it's broken
on older qcom chips, such as 8064.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Acquiring the reset GPIO low means that reset is being deasserted, this
is followed almost immediately with qcom_pcie_host_init() asserting it,
initializing it and then finally deasserting it again, for the link to
come up.
Some PCIe devices requires a minimum time between the initial deassert
and subsequent reset cycles. In a platform that boots with the reset
GPIO asserted this requirement is being violated by this deassert/assert
pulse.
Acquire the reset GPIO high to prevent this situation by matching the
state to the subsequent asserted state.
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org
The driver does not cope with the fact that probe can fail in a number
of cases after enabling runtime PM on the device; this results in
warnings about "Unbalanced pm_runtime_enable". Furthermore if probe
fails after invoking qcom_pcie_host_init() the power-domain will be left
referenced.
As it is not possible for the error handling in qcom_pcie_host_init() to
handle errors happening after returning from that function the
pm_runtime_get_sync() is moved to qcom_pcie_probe() as well.
Fixes: 854b69efbd ("PCI: qcom: add runtime pm support to pcie_port")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Function dw_pcie_host_init() already initializes the root_bus_nr field
of 'struct pcie_port', so the -1 assignment prior to calling
dw_pcie_host_init() in platform specific driver is not really needed.
Drop it.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Native PCI drivers for root complex devices were originally all in
drivers/pci/host/. Some of these devices can also be operated in endpoint
mode. Drivers for endpoint mode didn't seem to fit in the "host"
directory, so we put both the root complex and endpoint drivers in
per-device directories, e.g., drivers/pci/dwc/, drivers/pci/cadence/, etc.
These per-device directories contain trivial Kconfig and Makefiles and
clutter drivers/pci/. Make a new drivers/pci/controllers/ directory and
collect all the device-specific drivers there.
No functional change intended.
Link: https://lkml.kernel.org/r/1520304202-232891-1-git-send-email-shawn.lin@rock-chips.com
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
