[ Upstream commit 1e346cbb096a5351a637ec1992beffbf330547f0 ]
There is currently no return check for writing an authentication
type (HERMES_AUTH_SHARED_KEY or HERMES_AUTH_OPEN). It looks like
it was accidentally skipped.
This patch adds a return check similar to the other checks in
__orinoco_hw_setup_enc() for hermes_write_wordrec().
Detected using the static analysis tool - Svace.
Fixes: 1da177e4c3 ("Linux-2.6.12-rc2")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221227133306.201356-1-aleksei.kodanev@bell-sw.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b39f662ce1648db0b9de32e6a849b098480793cb ]
The wifi + bluetooth combo chip RTL8723BU can leak memory (especially?)
when it's connected to a bluetooth audio device. The busy bluetooth
traffic generates lots of C2H (card to host) messages, which are not
freed correctly.
To fix this, move the dev_kfree_skb() call in rtl8xxxu_c2hcmd_callback()
inside the loop where skb_dequeue() is called.
The RTL8192EU leaks memory because the C2H messages are added to the
queue and left there forever. (This was fine in the past because it
probably wasn't sending any C2H messages until commit e542e66b7c
("wifi: rtl8xxxu: gen2: Turn on the rate control"). Since that commit
it sends a C2H message when the TX rate changes.)
To fix this, delete the check for rf_paths > 1 and the goto. Let the
function process the C2H messages from RTL8192EU like the ones from
the other chips.
Theoretically the RTL8188FU could also leak like RTL8723BU, but it
most likely doesn't send C2H messages frequently enough.
This change was tested with RTL8723BU by Erhard F. I tested it with
RTL8188FU and RTL8192EU.
Reported-by: Erhard F. <erhard_f@mailbox.org>
Tested-by: Erhard F. <erhard_f@mailbox.org>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=215197
Fixes: e542e66b7c ("rtl8xxxu: add bluetooth co-existence support for single antenna")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/03b099c1-c671-d252-36f4-57b70d721f9d@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f393df151540bf858effbd29ff572ab94e76a4c4 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: d2e7b3425c ("libertas: disable functionality when interface is down")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-4-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3968e81ba644f10a7d45bae2539560db9edac501 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: a3128feef6 ("libertas: use irqsave() in USB's complete callback")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-3-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9388ce97b98216833c969191ee6df61a7201d797 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: fc75122fab ("libertas_tf: use irqsave() in USB's complete callback")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-2-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b9f420032f2ba1e634b22ca7b433e5c40ea663af ]
After the DMA buffer is mapped to a physical address, address is stored
in pktids in brcmf_msgbuf_alloc_pktid(). Then, pktids is parsed in
brcmf_msgbuf_get_pktid()/brcmf_msgbuf_release_array() to obtain physaddr
and later unmap the DMA buffer. But when count is always equal to
pktids->array_size, physaddr isn't stored in pktids and the DMA buffer
will not be unmapped anyway.
Fixes: 9a1bb60250 ("brcmfmac: Adding msgbuf protocol.")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207013114.1748936-1-shaozhengchao@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9fe21dc626117fb44a8eb393713a86a620128ce3 ]
In the error path of ipw_wdev_init(), exception value is returned, and
the memory applied for in the function is not released. Also the memory
is not released in ipw_pci_probe(). As a result, memory leakage occurs.
So memory release needs to be added to the error path of ipw_wdev_init().
Fixes: a3caa99e6c ("libipw: initiate cfg80211 API conversion (v2)")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221209012422.182669-1-shaozhengchao@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 45fc6d7461f18df2f238caf0cbc5acc4163203d1 ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called to free and drop the SKB when
it's reset, so replace it with dev_kfree_skb_irq(). Compile tested
only.
Fixes: 43f66a6ce8 ("Add ipw2200 wireless driver.")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221208143826.2385218-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 117dbeda22ec5ea0918254d03b540ef8b8a64d53 ]
There is a global-out-of-bounds reported by KASAN:
BUG: KASAN: global-out-of-bounds in
_rtl8812ae_eq_n_byte.part.0+0x3d/0x84 [rtl8821ae]
Read of size 1 at addr ffffffffa0773c43 by task NetworkManager/411
CPU: 6 PID: 411 Comm: NetworkManager Tainted: G D
6.1.0-rc8+ #144 e15588508517267d37
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009),
Call Trace:
<TASK>
...
kasan_report+0xbb/0x1c0
_rtl8812ae_eq_n_byte.part.0+0x3d/0x84 [rtl8821ae]
rtl8821ae_phy_bb_config.cold+0x346/0x641 [rtl8821ae]
rtl8821ae_hw_init+0x1f5e/0x79b0 [rtl8821ae]
...
</TASK>
The root cause of the problem is that the comparison order of
"prate_section" in _rtl8812ae_phy_set_txpower_limit() is wrong. The
_rtl8812ae_eq_n_byte() is used to compare the first n bytes of the two
strings from tail to head, which causes the problem. In the
_rtl8812ae_phy_set_txpower_limit(), it was originally intended to meet
this requirement by carefully designing the comparison order.
For example, "pregulation" and "pbandwidth" are compared in order of
length from small to large, first is 3 and last is 4. However, the
comparison order of "prate_section" dose not obey such order requirement,
therefore when "prate_section" is "HT", when comparing from tail to head,
it will lead to access out of bounds in _rtl8812ae_eq_n_byte(). As
mentioned above, the _rtl8812ae_eq_n_byte() has the same function as
strcmp(), so just strcmp() is enough.
Fix it by removing _rtl8812ae_eq_n_byte() and use strcmp() barely.
Although it can be fixed by adjusting the comparison order of
"prate_section", this may cause the value of "rate_section" to not be
from 0 to 5. In addition, commit "21e4b0726dc6" not only moved driver
from staging to regular tree, but also added setting txpower limit
function during the driver config phase, so the problem was introduced
by this commit.
Fixes: 21e4b0726d ("rtlwifi: rtl8821ae: Move driver from staging to regular tree")
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221212025812.1541311-1-lizetao1@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ef41937631bfee855e2b406e1d536efdaa9ce512 ]
There are thousands of warnings in a W=2 build from just one file:
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/table.c:3788:15: warning: pointer targets in initialization of 'u8 *' {aka 'unsigned char *'} from 'char *' differ in signedness [-Wpointer-sign]
Change the types to consistently use 'const char *' for the
strings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201026213040.3889546-6-arnd@kernel.org
Stable-dep-of: 117dbeda22ec ("wifi: rtlwifi: Fix global-out-of-bounds bug in _rtl8812ae_phy_set_txpower_limit()")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4c2005ac87685907b3719b4f40215b578efd27c4 ]
It is not allowed to call kfree_skb() or consume_skb() from hardware
interrupt context or with hardware interrupts being disabled.
It should use dev_kfree_skb_irq() or dev_consume_skb_irq() instead.
The difference between them is free reason, dev_kfree_skb_irq() means
the SKB is dropped in error and dev_consume_skb_irq() means the SKB
is consumed in normal.
In this case, dev_kfree_skb() is called to free and drop the SKB when
it's shutdown, so replace it with dev_kfree_skb_irq(). Compile tested
only.
Fixes: 26f1fad29a ("New driver: rtl8xxxu (mac80211)")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221208143517.2383424-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0c1528675d7a9787cb516b64d8f6c0f6f8efcb48 ]
It is not allowed to call consume_skb() from hardware interrupt context
or with interrupts being disabled. So replace dev_kfree_skb() with
dev_consume_skb_irq() under spin_lock_irqsave(). Compile tested only.
Fixes: 4bc85c1324 ("Revert "iwlwifi: split the drivers for agn and legacy devices 3945/4965"")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207144013.70210-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 313950c2114e7051c4e3020fd82495fa1fb526a8 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. All the SKBs have
been dequeued from the old queue, so it's safe to enqueue these
SKBs to a free queue, then free them after spin_unlock_irqrestore()
at once. Compile tested only.
Fixes: 5c99f04fec ("rtlwifi: rtl8723be: Update driver to match Realtek release of 06/28/14")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207141411.46098-4-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2611687fa7ffc84190f92292de0b80468de17220 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. All the SKBs have
been dequeued from the old queue, so it's safe to enqueue these
SKBs to a free queue, then free them after spin_unlock_irqrestore()
at once. Compile tested only.
Fixes: 7fe3b3abb5 ("rtlwifi: rtl8188ee: rtl8821ae: Fix a queue locking problem")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207141411.46098-3-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 106031c1f4a850915190d7ec1026696282f9359b ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. All the SKBs have
been dequeued from the old queue, so it's safe to enqueue these
SKBs to a free queue, then free them after spin_unlock_irqrestore()
at once. Compile tested only.
Fixes: 5c99f04fec ("rtlwifi: rtl8723be: Update driver to match Realtek release of 06/28/14")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207141411.46098-2-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 791082ec0ab843e0be07c8ce3678e4c2afd2e33d ]
Re-enable the function rtl8xxxu_gen2_report_connect.
It informs the firmware when connecting to a network. This makes the
firmware enable the rate control, which makes the upload faster.
It also informs the firmware when disconnecting from a network. In the
past this made reconnecting impossible because it was sending the
auth on queue 0x7 (TXDESC_QUEUE_VO) instead of queue 0x12
(TXDESC_QUEUE_MGNT):
wlp0s20f0u3: send auth to 90:55:de:__:__:__ (try 1/3)
wlp0s20f0u3: send auth to 90:55:de:__:__:__ (try 2/3)
wlp0s20f0u3: send auth to 90:55:de:__:__:__ (try 3/3)
wlp0s20f0u3: authentication with 90:55:de:__:__:__ timed out
Probably the firmware disables the unnecessary TX queues when it
knows it's disconnected.
However, this was fixed in commit edd5747aa12e ("wifi: rtl8xxxu: Fix
skb misuse in TX queue selection").
Fixes: c59f13bbea ("rtl8xxxu: Work around issue with 8192eu and 8723bu devices not reconnecting")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/43200afc-0c65-ee72-48f8-231edd1df493@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4920ab131b2dbae7464b72bdcac465d070254209 upstream.
This patch fixes slab-out-of-bounds reads in brcmfmac that occur in
brcmf_construct_chaninfo() and brcmf_enable_bw40_2g() when the count
value of channel specifications provided by the device is greater than
the length of 'list->element[]', decided by the size of the 'list'
allocated with kzalloc(). The patch adds checks that make the functions
free the buffer and return -EINVAL if that is the case. Note that the
negative return is handled by the caller, brcmf_setup_wiphybands() or
brcmf_cfg80211_attach().
Found by a modified version of syzkaller.
Crash Report from brcmf_construct_chaninfo():
==================================================================
BUG: KASAN: slab-out-of-bounds in brcmf_setup_wiphybands+0x1238/0x1430
Read of size 4 at addr ffff888115f24600 by task kworker/0:2/1896
CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G W O 5.14.0+ #132
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: usb_hub_wq hub_event
Call Trace:
dump_stack_lvl+0x57/0x7d
print_address_description.constprop.0.cold+0x93/0x334
kasan_report.cold+0x83/0xdf
brcmf_setup_wiphybands+0x1238/0x1430
brcmf_cfg80211_attach+0x2118/0x3fd0
brcmf_attach+0x389/0xd40
brcmf_usb_probe+0x12de/0x1690
usb_probe_interface+0x25f/0x710
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_set_configuration+0x984/0x1770
usb_generic_driver_probe+0x69/0x90
usb_probe_device+0x9c/0x220
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_new_device.cold+0x463/0xf66
hub_event+0x10d5/0x3330
process_one_work+0x873/0x13e0
worker_thread+0x8b/0xd10
kthread+0x379/0x450
ret_from_fork+0x1f/0x30
Allocated by task 1896:
kasan_save_stack+0x1b/0x40
__kasan_kmalloc+0x7c/0x90
kmem_cache_alloc_trace+0x19e/0x330
brcmf_setup_wiphybands+0x290/0x1430
brcmf_cfg80211_attach+0x2118/0x3fd0
brcmf_attach+0x389/0xd40
brcmf_usb_probe+0x12de/0x1690
usb_probe_interface+0x25f/0x710
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_set_configuration+0x984/0x1770
usb_generic_driver_probe+0x69/0x90
usb_probe_device+0x9c/0x220
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_new_device.cold+0x463/0xf66
hub_event+0x10d5/0x3330
process_one_work+0x873/0x13e0
worker_thread+0x8b/0xd10
kthread+0x379/0x450
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at ffff888115f24000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1536 bytes inside of
2048-byte region [ffff888115f24000, ffff888115f24800)
Memory state around the buggy address:
ffff888115f24500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff888115f24580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff888115f24600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff888115f24680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888115f24700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Crash Report from brcmf_enable_bw40_2g():
==================================================================
BUG: KASAN: slab-out-of-bounds in brcmf_cfg80211_attach+0x3d11/0x3fd0
Read of size 4 at addr ffff888103787600 by task kworker/0:2/1896
CPU: 0 PID: 1896 Comm: kworker/0:2 Tainted: G W O 5.14.0+ #132
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: usb_hub_wq hub_event
Call Trace:
dump_stack_lvl+0x57/0x7d
print_address_description.constprop.0.cold+0x93/0x334
kasan_report.cold+0x83/0xdf
brcmf_cfg80211_attach+0x3d11/0x3fd0
brcmf_attach+0x389/0xd40
brcmf_usb_probe+0x12de/0x1690
usb_probe_interface+0x25f/0x710
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_set_configuration+0x984/0x1770
usb_generic_driver_probe+0x69/0x90
usb_probe_device+0x9c/0x220
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_new_device.cold+0x463/0xf66
hub_event+0x10d5/0x3330
process_one_work+0x873/0x13e0
worker_thread+0x8b/0xd10
kthread+0x379/0x450
ret_from_fork+0x1f/0x30
Allocated by task 1896:
kasan_save_stack+0x1b/0x40
__kasan_kmalloc+0x7c/0x90
kmem_cache_alloc_trace+0x19e/0x330
brcmf_cfg80211_attach+0x3302/0x3fd0
brcmf_attach+0x389/0xd40
brcmf_usb_probe+0x12de/0x1690
usb_probe_interface+0x25f/0x710
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_set_configuration+0x984/0x1770
usb_generic_driver_probe+0x69/0x90
usb_probe_device+0x9c/0x220
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
bus_for_each_drv+0x123/0x1a0
__device_attach+0x207/0x330
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
usb_new_device.cold+0x463/0xf66
hub_event+0x10d5/0x3330
process_one_work+0x873/0x13e0
worker_thread+0x8b/0xd10
kthread+0x379/0x450
ret_from_fork+0x1f/0x30
The buggy address belongs to the object at ffff888103787000
which belongs to the cache kmalloc-2k of size 2048
The buggy address is located 1536 bytes inside of
2048-byte region [ffff888103787000, ffff888103787800)
Memory state around the buggy address:
ffff888103787500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff888103787580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>ffff888103787600: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
^
ffff888103787680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
ffff888103787700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
==================================================================
Reported-by: Dokyung Song <dokyungs@yonsei.ac.kr>
Reported-by: Jisoo Jang <jisoo.jang@yonsei.ac.kr>
Reported-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221116142952.518241-1-linuxlovemin@yonsei.ac.kr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b870e73a56c4cccbec33224233eaf295839f228c ]
Since resplen and respoffs are signed integers sufficiently
large values of unsigned int len and offset members of RNDIS
response will result in negative values of prior variables.
This may be utilized to bypass implemented security checks
to either extract memory contents by manipulating offset or
overflow the data buffer via memcpy by manipulating both
offset and len.
Additionally assure that sum of resplen and respoffs does not
overflow so buffer boundaries are kept.
Fixes: 80f8c5b434 ("rndis_wlan: copy only useful data from rndis_command respond")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230111175031.7049-1-szymon.heidrich@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 93fbc1ebd978cf408ef5765e9c1630fce9a8621b upstream.
Since IQK could spend time, we make a cache of IQK result matrix that looks
like iqk_matrix[channel_idx].val[x][y], and we can reload the matrix if we
have made a cache. To determine a cache is made, we check
iqk_matrix[channel_idx].val[0][0].
The initial commit 7274a8c229 ("rtlwifi: rtl8192de: Merge phy routines")
make a mistake that checks incorrect iqk_matrix[channel_idx].val[0] that
is always true, and this mistake is found by commit ee3db469dd31
("wifi: rtlwifi: remove always-true condition pointed out by GCC 12"), so
I recall the vendor driver to find fix and apply the correctness.
Fixes: 7274a8c229 ("rtlwifi: rtl8192de: Merge phy routines")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220801113345.42016-1-pkshih@realtek.com
Signed-off-by: Semyon Verchenko <semverchenko@factor-ts.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ee3db469dd317e82f57b13aa3bc61be5cb60c2b4 upstream.
The .value is a two-dim array, not a pointer.
struct iqk_matrix_regs {
bool iqk_done;
long value[1][IQK_MATRIX_REG_NUM];
};
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Semyon Verchenko <semverchenko@factor-ts.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 81d17f6f3331f03c8eafdacea68ab773426c1e3c ]
This patch fixes a shift-out-of-bounds in brcmfmac that occurs in
BIT(chiprev) when a 'chiprev' provided by the device is too large.
It should also not be equal to or greater than BITS_PER_TYPE(u32)
as we do bitwise AND with a u32 variable and BIT(chiprev). The patch
adds a check that makes the function return NULL if that is the case.
Note that the NULL case is later handled by the bus-specific caller,
brcmf_usb_probe_cb() or brcmf_usb_reset_resume(), for example.
Found by a modified version of syzkaller.
UBSAN: shift-out-of-bounds in drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c
shift exponent 151055786 is too large for 64-bit type 'long unsigned int'
CPU: 0 PID: 1885 Comm: kworker/0:2 Tainted: G O 5.14.0+ #132
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
Workqueue: usb_hub_wq hub_event
Call Trace:
dump_stack_lvl+0x57/0x7d
ubsan_epilogue+0x5/0x40
__ubsan_handle_shift_out_of_bounds.cold+0x53/0xdb
? lock_chain_count+0x20/0x20
brcmf_fw_alloc_request.cold+0x19/0x3ea
? brcmf_fw_get_firmwares+0x250/0x250
? brcmf_usb_ioctl_resp_wait+0x1a7/0x1f0
brcmf_usb_get_fwname+0x114/0x1a0
? brcmf_usb_reset_resume+0x120/0x120
? number+0x6c4/0x9a0
brcmf_c_process_clm_blob+0x168/0x590
? put_dec+0x90/0x90
? enable_ptr_key_workfn+0x20/0x20
? brcmf_common_pd_remove+0x50/0x50
? rcu_read_lock_sched_held+0xa1/0xd0
brcmf_c_preinit_dcmds+0x673/0xc40
? brcmf_c_set_joinpref_default+0x100/0x100
? rcu_read_lock_sched_held+0xa1/0xd0
? rcu_read_lock_bh_held+0xb0/0xb0
? lock_acquire+0x19d/0x4e0
? find_held_lock+0x2d/0x110
? brcmf_usb_deq+0x1cc/0x260
? mark_held_locks+0x9f/0xe0
? lockdep_hardirqs_on_prepare+0x273/0x3e0
? _raw_spin_unlock_irqrestore+0x47/0x50
? trace_hardirqs_on+0x1c/0x120
? brcmf_usb_deq+0x1a7/0x260
? brcmf_usb_rx_fill_all+0x5a/0xf0
brcmf_attach+0x246/0xd40
? wiphy_new_nm+0x1476/0x1d50
? kmemdup+0x30/0x40
brcmf_usb_probe+0x12de/0x1690
? brcmf_usbdev_qinit.constprop.0+0x470/0x470
usb_probe_interface+0x25f/0x710
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
? usb_match_id.part.0+0x88/0xc0
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
? driver_allows_async_probing+0x120/0x120
bus_for_each_drv+0x123/0x1a0
? bus_rescan_devices+0x20/0x20
? lockdep_hardirqs_on_prepare+0x273/0x3e0
? trace_hardirqs_on+0x1c/0x120
__device_attach+0x207/0x330
? device_bind_driver+0xb0/0xb0
? kobject_uevent_env+0x230/0x12c0
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
? __mutex_unlock_slowpath+0xe7/0x660
? __fw_devlink_link_to_suppliers+0x550/0x550
usb_set_configuration+0x984/0x1770
? kernfs_create_link+0x175/0x230
usb_generic_driver_probe+0x69/0x90
usb_probe_device+0x9c/0x220
really_probe+0x1be/0xa90
__driver_probe_device+0x2ab/0x460
driver_probe_device+0x49/0x120
__device_attach_driver+0x18a/0x250
? driver_allows_async_probing+0x120/0x120
bus_for_each_drv+0x123/0x1a0
? bus_rescan_devices+0x20/0x20
? lockdep_hardirqs_on_prepare+0x273/0x3e0
? trace_hardirqs_on+0x1c/0x120
__device_attach+0x207/0x330
? device_bind_driver+0xb0/0xb0
? kobject_uevent_env+0x230/0x12c0
bus_probe_device+0x1a2/0x260
device_add+0xa61/0x1ce0
? __fw_devlink_link_to_suppliers+0x550/0x550
usb_new_device.cold+0x463/0xf66
? hub_disconnect+0x400/0x400
? _raw_spin_unlock_irq+0x24/0x30
hub_event+0x10d5/0x3330
? hub_port_debounce+0x280/0x280
? __lock_acquire+0x1671/0x5790
? wq_calc_node_cpumask+0x170/0x2a0
? lock_release+0x640/0x640
? rcu_read_lock_sched_held+0xa1/0xd0
? rcu_read_lock_bh_held+0xb0/0xb0
? lockdep_hardirqs_on_prepare+0x273/0x3e0
process_one_work+0x873/0x13e0
? lock_release+0x640/0x640
? pwq_dec_nr_in_flight+0x320/0x320
? rwlock_bug.part.0+0x90/0x90
worker_thread+0x8b/0xd10
? __kthread_parkme+0xd9/0x1d0
? process_one_work+0x13e0/0x13e0
kthread+0x379/0x450
? _raw_spin_unlock_irq+0x24/0x30
? set_kthread_struct+0x100/0x100
ret_from_fork+0x1f/0x30
Reported-by: Dokyung Song <dokyungs@yonsei.ac.kr>
Reported-by: Jisoo Jang <jisoo.jang@yonsei.ac.kr>
Reported-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr>
Signed-off-by: Minsuk Kang <linuxlovemin@yonsei.ac.kr>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221024071329.504277-1-linuxlovemin@yonsei.ac.kr
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16ef02bad239f11f322df8425d302be62f0443ce ]
The bug arises when a USB device claims to be an ATH9K but doesn't
have the expected endpoints. (In this case there was an interrupt
endpoint where the driver expected a bulk endpoint.) The kernel
needs to be able to handle such devices without getting an internal error.
usb 1-1: BOGUS urb xfer, pipe 3 != type 1
WARNING: CPU: 3 PID: 500 at drivers/usb/core/urb.c:493 usb_submit_urb+0xce2/0x1430 drivers/usb/core/urb.c:493
Modules linked in:
CPU: 3 PID: 500 Comm: kworker/3:2 Not tainted 5.10.135-syzkaller #0
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-1 04/01/2014
Workqueue: events request_firmware_work_func
RIP: 0010:usb_submit_urb+0xce2/0x1430 drivers/usb/core/urb.c:493
Call Trace:
ath9k_hif_usb_alloc_rx_urbs drivers/net/wireless/ath/ath9k/hif_usb.c:908 [inline]
ath9k_hif_usb_alloc_urbs+0x75e/0x1010 drivers/net/wireless/ath/ath9k/hif_usb.c:1019
ath9k_hif_usb_dev_init drivers/net/wireless/ath/ath9k/hif_usb.c:1109 [inline]
ath9k_hif_usb_firmware_cb+0x142/0x530 drivers/net/wireless/ath/ath9k/hif_usb.c:1242
request_firmware_work_func+0x12e/0x240 drivers/base/firmware_loader/main.c:1097
process_one_work+0x9af/0x1600 kernel/workqueue.c:2279
worker_thread+0x61d/0x12f0 kernel/workqueue.c:2425
kthread+0x3b4/0x4a0 kernel/kthread.c:313
ret_from_fork+0x22/0x30 arch/x86/entry/entry_64.S:299
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221008211532.74583-1-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 76c16af2cb10282274596e21add2c9f0b95c941b ]
The gen 2 chips RTL8192EU and RTL8188FU periodically send the driver
reports about the TX rate, and the driver passes these reports to
sta_statistics. The reports from RTL8192EU may or may not include the
channel width. The reports from RTL8188FU do not include it.
Only access the c2h->ra_report.bw field if the report (skb) is big
enough.
The other problem fixed here is that the code was actually never
changing the channel width initially reported by
rtl8xxxu_bss_info_changed because the value of RATE_INFO_BW_20 is 0.
Fixes: 0985d3a410 ("rtl8xxxu: Feed current txrate information for mac80211")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/5b41f1ae-72e7-6b7a-2459-b736399a1c40@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd469a754afdb782ba3033cee102147493dc39f4 ]
This struct is used to access a sequence of bytes received from the
wifi chip. It must not have any padding bytes between the members.
This doesn't change anything on my system, possibly because currently
none of the members need more than byte alignment.
Fixes: b2b43b7837 ("rtl8xxxu: Initial functionality to handle C2H events for 8723bu")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Reviewed-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/1a270918-da22-ff5f-29fc-7855f740c5ba@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 03dd0d49de7db680a856fa566963bb8421f46368 ]
Make sure the nss is valid for nss_delta array. Return zero
if the index is invalid.
Coverity message:
Event overrun-call: Overrunning callee's array of size 4 by passing
argument "n_chains" (which evaluates to 15) in call to
"mt76_tx_power_nss_delta".
int delta = mt76_tx_power_nss_delta(n_chains);
Fixes: 07cda40630 ("mt76: fix rounding issues on converting per-chain and combined txpower")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2af7749047d8d6ad43feff69f555a13a6a6c2831 ]
This driver is attempting to register to support two different buses.
if either of these is successful then ath10k_pci_init() should return 0
so that hardware attached to the successful bus can be probed and
supported. only if both of these are unsuccessful should ath10k_pci_init()
return an errno.
Fixes: 0b523ced9a ("ath10k: add basic skeleton to support ahb")
Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221110061926.18163-1-xiujianfeng@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b8f6efccbb9dc0ff5dee7e20d69a4747298ee603 ]
When using wpa_supplicant v2.10, this driver is no longer able to
associate with any AP and fails in the EAPOL 4-way handshake while
sending the 2/4 message to the AP. The problem is not present in
wpa_supplicant v2.9 or older. The problem stems from HostAP commit
144314eaa ("wpa_supplicant: Send EAPOL frames over nl80211 where available")
which changes the way EAPOL frames are sent, from them being send
at L2 frames to them being sent via nl80211 control port.
An EAPOL frame sent as L2 frame is passed to the WiFi driver with
skb->protocol ETH_P_PAE, while EAPOL frame sent via nl80211 control
port has skb->protocol set to ETH_P_802_3 . The later happens in
ieee80211_tx_control_port(), where the EAPOL frame is encapsulated
into 802.3 frame.
The rsi_91x driver handles ETH_P_PAE EAPOL frames as high-priority
frames and sends them via highest-priority transmit queue, while
the ETH_P_802_3 frames are sent as regular frames. The EAPOL 4-way
handshake frames must be sent as highest-priority, otherwise the
4-way handshake times out.
Therefore, to fix this problem, inspect the skb control flags and
if flag IEEE80211_TX_CTRL_PORT_CTRL_PROTO is set, assume this is
an EAPOL frame and transmit the frame via high-priority queue just
like other ETH_P_PAE frames.
Fixes: 0eb42586cf ("rsi: data packet descriptor enhancements")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221104163339.227432-1-marex@denx.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 6f103aeb5e985ac08f3a4a049a2c17294f40cff9 ]
The wifi + bluetooth combo chips (RTL8723AU and RTL8723BU) read the
chip vendor from the wrong register because the val32 variable gets
overwritten. Add one more variable to avoid this.
This had no real effect on RTL8723BU. It may have had an effect on
RTL8723AU.
Fixes: 26f1fad29a ("New driver: rtl8xxxu (mac80211)")
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/24af8024-2f07-552b-93d8-38823d8e3cb0@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit dd95f2239fc846795fc926787c3ae0ca701c9840 ]
It is possible that skb is freed in ath9k_htc_rx_msg(), then
usb_submit_urb() fails and we try to free skb again. It causes
use-after-free bug. Moreover, if alloc_skb() fails, urb->context becomes
NULL but rx_buf is not freed and there can be a memory leak.
The patch removes unnecessary nskb and makes skb processing more clear: it
is supposed that ath9k_htc_rx_msg() either frees old skb or passes its
managing to another callback function.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 3deff76095 ("ath9k_htc: Increase URB count for REG_IN pipe")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221008114917.21404-1-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2a94de38c74e86f49124ac14f093d6a5c377a90 ]
Syzkaller reports a long-known leak of urbs in
ath9k_hif_usb_dealloc_tx_urbs().
The cause of the leak is that usb_get_urb() is called but usb_free_urb()
(or usb_put_urb()) is not called inside usb_kill_urb() as urb->dev or
urb->ep fields have not been initialized and usb_kill_urb() returns
immediately.
The patch removes trying to kill urbs located in hif_dev->tx.tx_buf
because hif_dev->tx.tx_buf is not supposed to contain urbs which are in
pending state (the pending urbs are stored in hif_dev->tx.tx_pending).
The tx.tx_lock is acquired so there should not be any changes in the list.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 03fb92a432 ("ath9k: hif_usb: fix race condition between usb_get_urb() and usb_kill_anchored_urbs()")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725151359.283704-1-pchelkin@ispras.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e6cb8769452e8236b52134e5cb4a18b8f5986932 ]
With char becoming unsigned by default, and with `char` alone being
ambiguous and based on architecture, we get a warning when assigning the
unchecked output of hex_to_bin() to that unsigned char. Mark `key` as a
`u8`, which matches the struct's type, and then check each call to
hex_to_bin() before casting.
Cc: Kalle Valo <kvalo@kernel.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221024162843.535921-1-Jason@zx2c4.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 69188df5f6e4cecc6b76b958979ba363cd5240e8 ]
Fixes a warning that occurs when rc table support is enabled
(IEEE80211_HW_SUPPORTS_RC_TABLE) in mac80211_hwsim and the PS mode
is changed via the exported debugfs attribute.
When the PS mode is changed, a packet is broadcasted via
hwsim_send_nullfunc by creating and transmitting a plain skb with only
header initialized. The ieee80211 rate array in the control buffer is
zero-initialized. When ratetbl support is enabled, ieee80211_get_tx_rates
is called for the skb with sta parameter set to NULL and thus no
ratetbl can be used. The final rate array then looks like
[-1,0; 0,0; 0,0; 0,0] which causes the warning in ieee80211_get_tx_rate.
The issue is fixed by setting the count of the first rate with idx '0'
to 1 and hence ieee80211_get_tx_rates won't overwrite it with idx '-1'.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
