commit eec679e4ac5f47507774956fb3479c206e761af7 upstream.
In a TLV encoding scheme, the Length part represents the length after
the header containing the values for type and length. In this case,
`tlv_len` should be:
tlv_len == (sizeof(*tlv_rxba) - 1) - sizeof(tlv_rxba->header) + tlv_bitmap_len
Notice that the `- 1` accounts for the one-element array `bitmap`, which
1-byte size is already included in `sizeof(*tlv_rxba)`.
So, if the above is correct, there is a double-counting of some members
in `struct mwifiex_ie_types_rxba_sync`, when `tlv_buf_left` and `tmp`
are calculated:
968 tlv_buf_left -= (sizeof(*tlv_rxba) + tlv_len);
969 tmp = (u8 *)tlv_rxba + tlv_len + sizeof(*tlv_rxba);
in specific, members:
drivers/net/wireless/marvell/mwifiex/fw.h:777
777 u8 mac[ETH_ALEN];
778 u8 tid;
779 u8 reserved;
780 __le16 seq_num;
781 __le16 bitmap_len;
This is clearly wrong, and affects the subsequent decoding of data in
`event_buf` through `tlv_rxba`:
970 tlv_rxba = (struct mwifiex_ie_types_rxba_sync *)tmp;
Fix this by using `sizeof(tlv_rxba->header)` instead of `sizeof(*tlv_rxba)`
in the calculation of `tlv_buf_left` and `tmp`.
This results in the following binary differences before/after changes:
| drivers/net/wireless/marvell/mwifiex/11n_rxreorder.o
| @@ -4698,11 +4698,11 @@
| drivers/net/wireless/marvell/mwifiex/11n_rxreorder.c:968
| tlv_buf_left -= (sizeof(tlv_rxba->header) + tlv_len);
| - 1da7: lea -0x11(%rbx),%edx
| + 1da7: lea -0x4(%rbx),%edx
| 1daa: movzwl %bp,%eax
| drivers/net/wireless/marvell/mwifiex/11n_rxreorder.c:969
| tmp = (u8 *)tlv_rxba + sizeof(tlv_rxba->header) + tlv_len;
| - 1dad: lea 0x11(%r15,%rbp,1),%r15
| + 1dad: lea 0x4(%r15,%rbp,1),%r15
The above reflects the desired change: avoid counting 13 too many bytes;
which is the total size of the double-counted members in
`struct mwifiex_ie_types_rxba_sync`:
$ pahole -C mwifiex_ie_types_rxba_sync drivers/net/wireless/marvell/mwifiex/11n_rxreorder.o
struct mwifiex_ie_types_rxba_sync {
struct mwifiex_ie_types_header header; /* 0 4 */
|-----------------------------------------------------------------------
| u8 mac[6]; /* 4 6 */ |
| u8 tid; /* 10 1 */ |
| u8 reserved; /* 11 1 */ |
| __le16 seq_num; /* 12 2 */ |
| __le16 bitmap_len; /* 14 2 */ |
| u8 bitmap[1]; /* 16 1 */ |
|----------------------------------------------------------------------|
| 13 bytes|
-----------
/* size: 17, cachelines: 1, members: 7 */
/* last cacheline: 17 bytes */
} __attribute__((__packed__));
Fixes: 99ffe72cda ("mwifiex: process rxba_sync event")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/06668edd68e7a26bbfeebd1201ae077a2a7a8bce.1692931954.git.gustavoars@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit dcce94b80a954a8968ff29fafcfb066d6197fa9a ]
When compiling with gcc 13.1 and CONFIG_FORTIFY_SOURCE=y,
I've noticed the following:
In function ‘fortify_memcpy_chk’,
inlined from ‘mwifiex_construct_tdls_action_frame’ at drivers/net/wireless/marvell/mwifiex/tdls.c:765:3,
inlined from ‘mwifiex_send_tdls_action_frame’ at drivers/net/wireless/marvell/mwifiex/tdls.c:856:6:
./include/linux/fortify-string.h:529:25: warning: call to ‘__read_overflow2_field’
declared with attribute warning: detected read beyond size of field (2nd parameter);
maybe use struct_group()? [-Wattribute-warning]
529 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The compiler actually complains on:
memmove(pos + ETH_ALEN, &mgmt->u.action.category,
sizeof(mgmt->u.action.u.tdls_discover_resp));
and it happens because the fortification logic interprets this
as an attempt to overread 1-byte 'u.action.category' member of
'struct ieee80211_mgmt'. To silence this warning, it's enough
to pass an address of 'u.action' itself instead of an address
of its first member.
This also fixes an improper usage of 'sizeof()'. Since 'skb' is
extended with 'sizeof(mgmt->u.action.u.tdls_discover_resp) + 1'
bytes (where 1 is actually 'sizeof(mgmt->u.action.category)'),
I assume that the same number of bytes should be copied.
Suggested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230629085115.180499-2-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 35a7a1ce7c7d61664ee54f5239a1f120ab95a87e ]
In 'mwifiex_handle_uap_rx_forward()', always check the value
returned by 'skb_copy()' to avoid potential NULL pointer
dereference in 'mwifiex_uap_queue_bridged_pkt()', and drop
original skb in case of copying failure.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 838e4f4492 ("mwifiex: improve uAP RX handling")
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230814095041.16416-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 288c63d5cb4667a51a04668b3e2bb0ea499bc5f4 ]
Add missing 'kfree_skb()' in 'mwifiex_init_rxq_ring()' and never do
'kfree(card->rxbd_ring_vbase)' because this area is DMAed and should
be released with 'dma_free_coherent()'. The latter is performed in
'mwifiex_pcie_delete_rxbd_ring()', which is now called to recover
from possible errors in 'mwifiex_pcie_create_rxbd_ring()'. Likewise
for 'mwifiex_pcie_init_evt_ring()', 'kfree(card->evtbd_ring_vbase)'
'mwifiex_pcie_delete_evtbd_ring()' and 'mwifiex_pcie_create_rxbd_ring()'.
Fixes: d930faee14 ("mwifiex: add support for Marvell pcie8766 chipset")
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230731074334.56463-1-dmantipov@yandex.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 139f6973bf140c65d4d1d4bde5485badb4454d7a ]
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/net/wireless/marvell/mwifiex/sdio.c:498:34: error: ‘mwifiex_sdio_of_match_table’ defined but not used [-Werror=unused-const-variable=]
drivers/net/wireless/marvell/mwifiex/pcie.c:175:34: error: ‘mwifiex_pcie_of_match_table’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230312132523.352182-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3cfb7df24cee0f5fdc4cc5d3176cab9aadfcb430 ]
This code re-uses "i" to be the iterator for both the inside and outside
loops. It means the outside loop will exit earlier than intended.
Fixes: d219b7eb37 ("mwifiex: handle BT coex event to adjust Rx BA window size")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/Y+ERnaDaZD7RtLvX@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f393df151540bf858effbd29ff572ab94e76a4c4 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: d2e7b3425c ("libertas: disable functionality when interface is down")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-4-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3968e81ba644f10a7d45bae2539560db9edac501 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: a3128feef6 ("libertas: use irqsave() in USB's complete callback")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-3-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9388ce97b98216833c969191ee6df61a7201d797 ]
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled. So replace kfree_skb()
with dev_kfree_skb_irq() under spin_lock_irqsave(). Compile
tested only.
Fixes: fc75122fab ("libertas_tf: use irqsave() in USB's complete callback")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20221207150008.111743-2-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a52ed4866d2b90dd5e4ae9dabd453f3ed8fa3cbc ]
There are sleep in atomic context bugs when uploading device dump
data in mwifiex. The root cause is that dev_coredumpv could not
be used in atomic contexts, because it calls dev_set_name which
include operations that may sleep. The call tree shows execution
paths that could lead to bugs:
(Interrupt context)
fw_dump_timer_fn
mwifiex_upload_device_dump
dev_coredumpv(..., GFP_KERNEL)
dev_coredumpm()
kzalloc(sizeof(*devcd), gfp); //may sleep
dev_set_name
kobject_set_name_vargs
kvasprintf_const(GFP_KERNEL, ...); //may sleep
kstrdup(s, GFP_KERNEL); //may sleep
The corresponding fail log is shown below:
[ 135.275938] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start
[ 135.281029] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265
...
[ 135.293613] Call Trace:
[ 135.293613] <IRQ>
[ 135.293613] dump_stack_lvl+0x57/0x7d
[ 135.293613] __might_resched.cold+0x138/0x173
[ 135.293613] ? dev_coredumpm+0xca/0x2e0
[ 135.293613] kmem_cache_alloc_trace+0x189/0x1f0
[ 135.293613] ? devcd_match_failing+0x30/0x30
[ 135.293613] dev_coredumpm+0xca/0x2e0
[ 135.293613] ? devcd_freev+0x10/0x10
[ 135.293613] dev_coredumpv+0x1c/0x20
[ 135.293613] ? devcd_match_failing+0x30/0x30
[ 135.293613] mwifiex_upload_device_dump+0x65/0xb0
[ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0
[ 135.293613] call_timer_fn+0x122/0x3d0
[ 135.293613] ? msleep_interruptible+0xb0/0xb0
[ 135.293613] ? lock_downgrade+0x3c0/0x3c0
[ 135.293613] ? __next_timer_interrupt+0x13c/0x160
[ 135.293613] ? lockdep_hardirqs_on_prepare+0xe/0x220
[ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0
[ 135.293613] __run_timers.part.0+0x3f8/0x540
[ 135.293613] ? call_timer_fn+0x3d0/0x3d0
[ 135.293613] ? arch_restore_msi_irqs+0x10/0x10
[ 135.293613] ? lapic_next_event+0x31/0x40
[ 135.293613] run_timer_softirq+0x4f/0xb0
[ 135.293613] __do_softirq+0x1c2/0x651
...
[ 135.293613] RIP: 0010:default_idle+0xb/0x10
[ 135.293613] RSP: 0018:ffff888006317e68 EFLAGS: 00000246
[ 135.293613] RAX: ffffffff82ad8d10 RBX: ffff888006301cc0 RCX: ffffffff82ac90e1
[ 135.293613] RDX: ffffed100d9ff1b4 RSI: ffffffff831ad140 RDI: ffffffff82ad8f20
[ 135.293613] RBP: 0000000000000003 R08: 0000000000000000 R09: ffff88806cff8d9b
[ 135.293613] R10: ffffed100d9ff1b3 R11: 0000000000000001 R12: ffffffff84593410
[ 135.293613] R13: 0000000000000000 R14: 0000000000000000 R15: 1ffff11000c62fd2
...
[ 135.389205] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end
This patch uses delayed work to replace timer and moves the operations
that may sleep into a delayed work in order to mitigate bugs, it was
tested on Marvell 88W8801 chip whose port is usb and the firmware is
usb8801_uapsta.bin. The following is the result after using delayed
work to replace timer.
[ 134.936453] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start
[ 135.043344] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end
As we can see, there is no bug now.
Fixes: f5ecd02a8b ("mwifiex: device dump support for usb interface")
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Link: https://lore.kernel.org/r/b63b77fc84ed3e8a6bef02378e17c7c71a0bc3be.1654569290.git.duoming@zju.edu.cn
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 84d94e16efa268e4f2887d858cd67ee37b870f25 ]
The firmware of the 88W8897 PCIe+USB card sends those events very
unreliably, sometimes bluetooth together with 2.4ghz-wifi is used and no
COEX event comes in, and sometimes bluetooth is disabled but the
coexistance mode doesn't get disabled.
This means we sometimes end up capping the rx/tx window size while
bluetooth is not enabled anymore, artifically limiting wifi speeds even
though bluetooth is not being used.
Since we can't fix the firmware, let's just ignore those events on the
88W8897 device. From some Wireshark capture sessions it seems that the
Windows driver also doesn't change the rx/tx window sizes when bluetooth
gets enabled or disabled, so this is fairly consistent with the Windows
driver.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211103205827.14559-1-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3e12968f6d12a34b540c39cbd696a760cc4616f0 ]
cfg80211_ch_switch_notify uses ASSERT_WDEV_LOCK to assert that
net_device->ieee80211_ptr->mtx (which is the same as priv->wdev.mtx)
is held during the function's execution.
mwifiex_dfs_chan_sw_work_queue is one of its callers, which does not
hold that lock, therefore violating the assertion.
Add a lock around the call.
Disclaimer:
I am currently working on a static analyser to detect missing locks.
This was a reported case. I manually verified the report by looking
at the code, so that I do not send wrong information or patches.
After concluding that this seems to be a true positive, I created
this patch.
However, as I do not in fact have this particular hardware,
I was unable to test it.
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220321225515.32113-1-dossche.niels@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 04d80663f67ccef893061b49ec8a42ff7045ae84 ]
Currently, with an unknown recv_type, mwifiex_usb_recv
just return -1 without restoring the skb. Next time
mwifiex_usb_rx_complete is invoked with the same skb,
calling skb_put causes skb_over_panic.
The bug is triggerable with a compromised/malfunctioning
usb device. After applying the patch, skb_over_panic
no longer shows up with the same input.
Attached is the panic report from fuzzing.
skbuff: skb_over_panic: text:000000003bf1b5fa
len:2048 put:4 head:00000000dd6a115b data:000000000a9445d8
tail:0x844 end:0x840 dev:<NULL>
kernel BUG at net/core/skbuff.c:109!
invalid opcode: 0000 [#1] SMP KASAN NOPTI
CPU: 0 PID: 198 Comm: in:imklog Not tainted 5.6.0 #60
RIP: 0010:skb_panic+0x15f/0x161
Call Trace:
<IRQ>
? mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
skb_put.cold+0x24/0x24
mwifiex_usb_rx_complete+0x26b/0xfcd [mwifiex_usb]
__usb_hcd_giveback_urb+0x1e4/0x380
usb_giveback_urb_bh+0x241/0x4f0
? __hrtimer_run_queues+0x316/0x740
? __usb_hcd_giveback_urb+0x380/0x380
tasklet_action_common.isra.0+0x135/0x330
__do_softirq+0x18c/0x634
irq_exit+0x114/0x140
smp_apic_timer_interrupt+0xde/0x380
apic_timer_interrupt+0xf/0x20
</IRQ>
Reported-by: Brendan Dolan-Gavitt <brendandg@nyu.edu>
Signed-off-by: Zekun Shen <bruceshenzk@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/YX4CqjfRcTa6bVL+@Zekuns-MBP-16.fios-router.home
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1b8bb8919ef81bfc8873d223b9361f1685f2106d ]
Quoting Jia-Ju Bai <baijiaju1990@gmail.com>:
mwifiex_dequeue_tx_packet()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 1432 (Lock A)
mwifiex_send_addba()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 608 (Lock B)
mwifiex_process_sta_tx_pause()
spin_lock_bh(&priv->sta_list_spinlock); --> Line 398 (Lock B)
mwifiex_update_ralist_tx_pause()
spin_lock_bh(&priv->wmm.ra_list_spinlock); --> Line 941 (Lock A)
Similar report for mwifiex_process_uap_tx_pause().
While the locking expectations in this driver are a bit unclear, the
Fixed commit only intended to protect the sta_ptr, so we can drop the
lock as soon as we're done with it.
IIUC, this deadlock cannot actually happen, because command event
processing (which calls mwifiex_process_sta_tx_pause()) is
sequentialized with TX packet processing (e.g.,
mwifiex_dequeue_tx_packet()) via the main loop (mwifiex_main_process()).
But it's good not to leave this potential issue lurking.
Fixes: f0f7c2275f ("mwifiex: minor cleanups w/ sta_list_spinlock in cfg80211.c")
Cc: Douglas Anderson <dianders@chromium.org>
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Link: https://lore.kernel.org/linux-wireless/0e495b14-efbb-e0da-37bd-af6bd677ee2c@gmail.com/
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/YaV0pllJ5p/EuUat@google.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc8a8bc37466f79b24d972555237f3d591150602 ]
While looking at on-air packets using Wireshark, I noticed we're never
setting the initiator bit when sending DELBA requests to the AP: While
we set the bit on our del_ba_param_set bitmask, we forget to actually
copy that bitmask over to the command struct, which means we never
actually set the initiator bit.
Fix that and copy the bitmask over to the host_cmd_ds_11n_delba command
struct.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Acked-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211016153244.24353-5-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c606008b70627a2fc485732a53cc22f0f66d0981 ]
When creating a new virtual interface in mwifiex_add_virtual_intf(), we
update our internal driver states like bss_type, bss_priority, bss_role
and bss_mode to reflect the mode the firmware will be set to.
When switching virtual interface mode using
mwifiex_init_new_priv_params() though, we currently only update bss_mode
and bss_role. In order for the interface mode switch to actually work,
we also need to update bss_type to its proper value, so do that.
This fixes a crash of the firmware (because the driver tries to execute
commands that are invalid in AP mode) when switching from station mode
to AP mode.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-9-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c2e9666cdffd347460a2b17988db4cfaf2a68fb9 ]
We currently handle changing from the P2P to the STATION virtual
interface type slightly different than changing from P2P to ADHOC: When
changing to STATION, we don't send the SET_BSS_MODE command. We do send
that command on all other type-changes though, and it probably makes
sense to send the command since after all we just changed our BSS_MODE.
Looking at prior changes to this part of the code, it seems that this is
simply a leftover from old refactorings.
Since sending the SET_BSS_MODE command is the only difference between
mwifiex_change_vif_to_sta_adhoc() and the current code, we can now use
mwifiex_change_vif_to_sta_adhoc() for both switching to ADHOC and
STATION interface type.
This does not fix any particular bug and just "looked right", so there's
a small chance it might be a regression.
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914195909.36035-4-verdre@v0yd.nl
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8e3e59c31fea5de95ffc52c46f0c562c39f20c59 upstream.
It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.
Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.
Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.
The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.
Here's a reproducer for those firmware wakeup failures I've found:
1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e5f4eb8223aa740237cd463246a7debcddf4eda1 upstream.
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 89f8765a11d8df49296d92c404067f9b5c58ee26 upstream.
Add the missing endpoint sanity checks to probe() to avoid division by
zero in mwifiex_write_data_sync() in case a malicious device has broken
descriptors (or when doing descriptor fuzz testing).
Only add checks for the firmware-download boot stage, which require both
command endpoints, for now. The driver looks like it will handle a
missing endpoint during normal operation without oopsing, albeit not
very gracefully as it will try to submit URBs to the default pipe and
fail.
Note that USB core will reject URBs submitted for endpoints with zero
wMaxPacketSize but that drivers doing packet-size calculations still
need to handle this (cf. commit 2548288b4f ("USB: Fix: Don't skip
endpoint descriptors with maxpacket=0")).
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Cc: stable@vger.kernel.org # 3.5
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211027080819.6675-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8f4e3d48bb50765ab27ae5bebed2595b20de80a1 ]
A patch from 2017 changed some accesses to DMA memory to use
get_unaligned_le32() and similar interfaces, to avoid problems
with doing unaligned accesson uncached memory.
However, the change in the mwifiex_pcie_alloc_sleep_cookie_buf()
function ended up changing the size of the access instead,
as it operates on a pointer to u8.
Change this function back to actually access the entire 32 bits.
Note that the pointer is aligned by definition because it came
from dma_alloc_coherent().
Fixes: 92c70a958b ("mwifiex: fix for unaligned reads")
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7e79b38fe9a403b065ac5915465f620a8fb3de84 ]
The libertas driver was trying to register sysfs groups "by hand" which
causes them to be created _after_ the device is initialized and
announced to userspace, which causes races and can prevent userspace
tools from seeing the sysfs files correctly.
Fix this up by using the built-in sysfs_groups pointers in struct
net_device which were created for this very reason, fixing the race
condition, and properly allowing for any error that might have occured
to be handled properly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-54-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 46651077765c80a0d6f87f3469129a72e49ce91b ]
This reverts commit 434256833d.
Because of recent interactions with developers from @umn.edu, all
commits from them have been recently re-reviewed to ensure if they were
correct or not.
Upon review, this commit was found to be incorrect for the reasons
below, so it must be reverted. It will be fixed up "correctly" in a
later kernel change.
The original commit was incorrect, the error needs to be propagated back
to the caller AND if the second group call fails, the first needs to be
removed. There are much better ways to solve this, the driver should
NOT be calling sysfs_create_group() on its own as it is racing userspace
and loosing.
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210503115736.2104747-53-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a8e083ee8e2a6c94c29733835adae8bf5b832748 ]
In mwl8k_probe_hw, hw->priv->txq is freed at the first time by
dma_free_coherent() in the call chain:
if(!priv->ap_fw)->mwl8k_init_txqs(hw)->mwl8k_txq_init(hw, i).
Then in err_free_queues of mwl8k_probe_hw, hw->priv->txq is freed
at the second time by mwl8k_txq_deinit(hw, i)->dma_free_coherent().
My patch set txq->txd to NULL after the first free to avoid the
double free.
Fixes: a66098daac ("mwl8k: Marvell TOPDOG wireless driver")
Signed-off-by: Lv Yunlong <lyl2019@mail.ustc.edu.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210402182627.4256-1-lyl2019@mail.ustc.edu.cn
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4add4d988f95f47493500a7a19c623827061589b ]
If a reset is performed, but even the reset fails for some reasons (e.g.,
on Surface devices, the fw reset requires another quirks),
cancel_work_sync() hangs in mwifiex_cleanup_pcie().
# firmware went into a bad state
[...]
[ 1608.281690] mwifiex_pcie 0000:03:00.0: info: shutdown mwifiex...
[ 1608.282724] mwifiex_pcie 0000:03:00.0: rx_pending=0, tx_pending=1, cmd_pending=0
[ 1608.292400] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
[ 1608.292405] mwifiex_pcie 0000:03:00.0: PREP_CMD: card is removed
# reset performed after firmware went into a bad state
[ 1609.394320] mwifiex_pcie 0000:03:00.0: WLAN FW already running! Skip FW dnld
[ 1609.394335] mwifiex_pcie 0000:03:00.0: WLAN FW is active
# but even the reset failed
[ 1619.499049] mwifiex_pcie 0000:03:00.0: mwifiex_cmd_timeout_func: Timeout cmd id = 0xfa, act = 0xe000
[ 1619.499094] mwifiex_pcie 0000:03:00.0: num_data_h2c_failure = 0
[ 1619.499103] mwifiex_pcie 0000:03:00.0: num_cmd_h2c_failure = 0
[ 1619.499110] mwifiex_pcie 0000:03:00.0: is_cmd_timedout = 1
[ 1619.499117] mwifiex_pcie 0000:03:00.0: num_tx_timeout = 0
[ 1619.499124] mwifiex_pcie 0000:03:00.0: last_cmd_index = 0
[ 1619.499133] mwifiex_pcie 0000:03:00.0: last_cmd_id: fa 00 07 01 07 01 07 01 07 01
[ 1619.499140] mwifiex_pcie 0000:03:00.0: last_cmd_act: 00 e0 00 00 00 00 00 00 00 00
[ 1619.499147] mwifiex_pcie 0000:03:00.0: last_cmd_resp_index = 3
[ 1619.499155] mwifiex_pcie 0000:03:00.0: last_cmd_resp_id: 07 81 07 81 07 81 07 81 07 81
[ 1619.499162] mwifiex_pcie 0000:03:00.0: last_event_index = 2
[ 1619.499169] mwifiex_pcie 0000:03:00.0: last_event: 58 00 58 00 58 00 58 00 58 00
[ 1619.499177] mwifiex_pcie 0000:03:00.0: data_sent=0 cmd_sent=1
[ 1619.499185] mwifiex_pcie 0000:03:00.0: ps_mode=0 ps_state=0
[ 1619.499215] mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
# mwifiex_pcie_work hang happening
[ 1823.233923] INFO: task kworker/3:1:44 blocked for more than 122 seconds.
[ 1823.233932] Tainted: G WC OE 5.10.0-rc1-1-mainline #1
[ 1823.233935] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 1823.233940] task:kworker/3:1 state:D stack: 0 pid: 44 ppid: 2 flags:0x00004000
[ 1823.233960] Workqueue: events mwifiex_pcie_work [mwifiex_pcie]
[ 1823.233965] Call Trace:
[ 1823.233981] __schedule+0x292/0x820
[ 1823.233990] schedule+0x45/0xe0
[ 1823.233995] schedule_timeout+0x11c/0x160
[ 1823.234003] wait_for_completion+0x9e/0x100
[ 1823.234012] __flush_work.isra.0+0x156/0x210
[ 1823.234018] ? flush_workqueue_prep_pwqs+0x130/0x130
[ 1823.234026] __cancel_work_timer+0x11e/0x1a0
[ 1823.234035] mwifiex_cleanup_pcie+0x28/0xd0 [mwifiex_pcie]
[ 1823.234049] mwifiex_free_adapter+0x24/0xe0 [mwifiex]
[ 1823.234060] _mwifiex_fw_dpc+0x294/0x560 [mwifiex]
[ 1823.234074] mwifiex_reinit_sw+0x15d/0x300 [mwifiex]
[ 1823.234080] mwifiex_pcie_reset_done+0x50/0x80 [mwifiex_pcie]
[ 1823.234087] pci_try_reset_function+0x5c/0x90
[ 1823.234094] process_one_work+0x1d6/0x3a0
[ 1823.234100] worker_thread+0x4d/0x3d0
[ 1823.234107] ? rescuer_thread+0x410/0x410
[ 1823.234112] kthread+0x142/0x160
[ 1823.234117] ? __kthread_bind_mask+0x60/0x60
[ 1823.234124] ret_from_fork+0x22/0x30
[...]
This is a deadlock caused by calling cancel_work_sync() in
mwifiex_cleanup_pcie():
- Device resets are done via mwifiex_pcie_card_reset()
- which schedules card->work to call mwifiex_pcie_card_reset_work()
- which calls pci_try_reset_function().
- This leads to mwifiex_pcie_reset_done() be called on the same workqueue,
which in turn calls
- mwifiex_reinit_sw() and that calls
- _mwifiex_fw_dpc().
The problem is now that _mwifiex_fw_dpc() calls mwifiex_free_adapter()
in case firmware initialization fails. That ends up calling
mwifiex_cleanup_pcie().
Note that all those calls are still running on the workqueue. So when
mwifiex_cleanup_pcie() now calls cancel_work_sync(), it's really waiting
on itself to complete, causing a deadlock.
This commit fixes the deadlock by skipping cancel_work_sync() on a reset
failure path.
After this commit, when reset fails, the following output is
expected to be shown:
kernel: mwifiex_pcie 0000:03:00.0: info: _mwifiex_fw_dpc: unregister device
kernel: mwifiex: Failed to bring up adapter: -5
kernel: mwifiex_pcie 0000:03:00.0: reinit failed: -5
To reproduce this issue, for example, try putting the root port of wifi
into D3 (replace "00:1d.3" with your setup).
# put into D3 (root port)
sudo setpci -v -s 00:1d.3 CAP_PM+4.b=0b
Cc: Maximilian Luz <luzmaximilian@gmail.com>
Signed-off-by: Tsuchiya Yuto <kitakar@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201028142346.18355-1-kitakar@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5c455c5ab332773464d02ba17015acdca198f03d ]
mwifiex_cmd_802_11_ad_hoc_start() calls memcpy() without checking
the destination size may trigger a buffer overflower,
which a local user could use to cause denial of service
or the execution of arbitrary code.
Fix it by putting the length check before calling memcpy().
Signed-off-by: Zhang Xiaohui <ruc_zhangxiaohui@163.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201206084801.26479-1-ruc_zhangxiaohui@163.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
clang static analysis reports this problem:
sdio.c:2403:3: warning: Attempt to free released memory
kfree(card->mpa_rx.buf);
^~~~~~~~~~~~~~~~~~~~~~~
When mwifiex_init_sdio() fails in its first call to
mwifiex_alloc_sdio_mpa_buffer, it falls back to calling it
again. If the second alloc of mpa_tx.buf fails, the error
handler will try to free the old, previously freed mpa_rx.buf.
Reviewing the code, it looks like a second double free would
happen with mwifiex_cleanup_sdio().
So set both pointers to NULL when they are freed.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201004131931.29782-1-trix@redhat.com
The usage of in_interrupt() in non-core code is phased out. Ideally the
information of the calling context should be passed by the callers or the
functions be split as appropriate.
libertas uses in_interupt() to select the netif_rx*() variant which matches
the calling context. The attempt to consolidate the code by passing an
arguemnt or by distangling it failed due lack of knowledge about this
driver and because the call chains are hard to follow.
As a stop gap use netif_rx_any_context() which invokes the correct code
path depending on context and confines the in_interrupt() usage to core
code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug macro prints (INT) when in_interrupt() returns true. The value of
this information is dubious as it does not distinguish between the various
contexts which are covered by in_interrupt().
As the usage of in_interrupt() in drivers is phased out and the same
information can be more precisely obtained with tracing, remove the
in_interrupt() conditional from this debug printk.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of in_interrupt() in non-core code is phased out. Ideally the
information of the calling context should be passed by the callers or the
functions be split as appropriate.
mwifiex uses in_interupt() to select the netif_rx*() variant which matches
the calling context. The attempt to consolidate the code by passing an
arguemnt or by distangling it failed due lack of knowledge about this
driver and because the call chains are hard to follow.
As a stop gap use netif_rx_any_context() which invokes the correct code
path depending on context and confines the in_interrupt() usage to core
code.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
clang static analyzer reports this problem
init.c:739:8: warning: Called function pointer
is null (null dereference)
ret = adapter->if_ops.check_fw_status( ...
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In mwifiex_dnld_fw, there is an earlier check for check_fw_status(),
The check was introduced for usb support at the same time this
check in _mwifiex_fw_dpc() was made
if (adapter->if_ops.dnld_fw) {
ret = adapter->if_ops.dnld_fw(adapter, &fw);
} else {
ret = mwifiex_dnld_fw(adapter, &fw);
}
And a dnld_fw function initialized as part the usb's
mwifiex_if_ops.
The other instances of mwifiex_if_ops for pci and sdio
both set check_fw_status.
So the first check is not needed and can be removed.
Fixes: 4daffe3543 ("mwifiex: add support for Marvell USB8797 chipset")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200906200548.18053-1-trix@redhat.com
These variables only used in sdio.c, move them to .c file
can silence these warnings:
In file included from drivers/net/wireless/marvell/mwifiex//main.h:59:0,
from drivers/net/wireless/marvell/mwifiex//cfp.c:24:
drivers/net/wireless/marvell/mwifiex//sdio.h:705:41: warning: ‘mwifiex_sdio_sd8801’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8801 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:689:41: warning: ‘mwifiex_sdio_sd8987’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8987 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:674:41: warning: ‘mwifiex_sdio_sd8887’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8887 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:658:41: warning: ‘mwifiex_sdio_sd8997’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8997 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:642:41: warning: ‘mwifiex_sdio_sd8977’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8977 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:627:41: warning: ‘mwifiex_sdio_sd8897’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8897 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:612:41: warning: ‘mwifiex_sdio_sd8797’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8797 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:597:41: warning: ‘mwifiex_sdio_sd8787’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8787 = {
^~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//sdio.h:582:41: warning: ‘mwifiex_sdio_sd8786’ defined but not used [-Wunused-const-variable=]
static const struct mwifiex_sdio_device mwifiex_sdio_sd8786 = {
^~~~~~~~~~~~~~~~~~~
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902141155.30144-1-yuehaibing@huawei.com
In file included from drivers/net/wireless/marvell/mwifiex//cmdevt.c:26:0:
drivers/net/wireless/marvell/mwifiex//wmm.h:41:17: warning: ‘tos_to_tid_inv’ defined but not used [-Wunused-const-variable=]
static const u8 tos_to_tid_inv[] = {
^~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex//wmm.h:34:18: warning: ‘mwifiex_1d_to_wmm_queue’ defined but not used [-Wunused-const-variable=]
static const u16 mwifiex_1d_to_wmm_queue[8] = { 1, 0, 0, 1, 2, 2, 3, 3 };
^~~~~~~~~~~~~~~~~~~~~~~
move the variables definition to .c file, and leave declarations
in the header file to fix these warnings.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200902140846.29024-1-yuehaibing@huawei.com
A new warning in clang points out when macro expansion might result in a
GNU C statement expression. There is an instance of this in the mwifiex
driver:
drivers/net/wireless/marvell/mwifiex/cmdevt.c:217:34: warning: '}' and
')' tokens terminating statement expression appear in different macro
expansion contexts [-Wcompound-token-split-by-macro]
host_cmd->seq_num = cpu_to_le16(HostCmd_SET_SEQ_NO_BSS_INFO
^~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/marvell/mwifiex/fw.h:519:46: note: expanded from
macro 'HostCmd_SET_SEQ_NO_BSS_INFO'
(((type) & 0x000f) << 12); }
^
This does not appear to be a real issue. Removing the braces and
replacing them with parentheses will fix the warning and not change the
meaning of the code.
Fixes: 5e6e3a92b9 ("wireless: mwifiex: initial commit for Marvell mwifiex driver")
Link: https://github.com/ClangBuiltLinux/linux/issues/1146
Reported-by: Andy Lavr <andy.lavr@gmail.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200901070834.1015754-1-natechancellor@gmail.com
