[ Upstream commit 36c7c640ffeb87168e5ff79b7a36ae3a020bd378 ]
Assign the correct hw_op ath11k_init_wmi_config_ipq8074 to
the hw IPQ8074. Also update the correct TWT radio count.
Incorrect TWT radio count cause TWT feature fails on radio2
because physical device count is hardcoded to 2. so set
the value dynamically.
Found this during code review.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Fixes: 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604512020-25197-1-git-send-email-periyasa@codeaurora.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
In commit 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params") the
wmi config initialisation was moved to hw_ops->wmi_init_config() but the old
initialisation values were accidentally left to ath11k_wmi_cmd_init(). This
is very confusing, so remove the redundant values.
And this was actually so confusing that in commit aa2092a9ba ("ath11k: add
raw mode and software crypto support") I actually it caused a bug: when
ATH11K_FLAG_RAW_MODE was enabled rx_decap_mode was assigned back to
TARGET_DECAP_MODE_NATIVE_WIFI in ath11k_init_wmi_config_ipq8074(). Fix this at
the same time.
Compile tested only.
Fixes: 2d4bcbed5b ("ath11k: initialize wmi config based on hw_params")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600356507-29237-1-git-send-email-kvalo@codeaurora.org
For QCA6390, only one pdev is created and this pdev manages both lmacs, thus
both rxdmas. So host needs to initialize all rxdma related rings for one pdev.
Another difference is for QCA6390, host fills rxbuf to firmware and firmware
further fills the rxbuf to rxbuf ring for each rxdma.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-4-git-send-email-kvalo@codeaurora.org
QCA6390 uses MSI interrupt, so need to configure msi_add and
msi_data to dp srngs. As there are so many DP srngs, so need
to group them. Each group shares one MSI interrupt.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-2-git-send-email-kvalo@codeaurora.org
QCA6390 uses only 9 Copy Engines while IPQ8074 may use 12, make it possible to
change CE configuration dynamically via hw_params.
The defines for host_ce_config_wlan and CE_COUNT are temporary solutions, they
will be removed in the following patches to keep things simple.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-4-git-send-email-kvalo@codeaurora.org
