[ Upstream commit b8d35024d4059ca550cba11ac9ab23a6c238d929 ]
The error handling in rtl8152_probe() is missing a call to release
firmware. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: 9370f2d05a ("r8152: support request_firmware for RTL8153")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit bb8adff9123e492598162ac1baad01a53891aef6 ]
The error handling in rtl8152_probe() is missing a call to cancel the
hw_phy_work. Add it in to match what's in the cleanup code in
rtl8152_disconnect().
Fixes: a028a9e003 ("r8152: move the settings of PHY to a work queue")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5dd17689526971c5ae12bc8398f34bd68cd0499e ]
The rtl8152_probe() function lacks a call to the chip-specific
unload() routine when it sees an error in probe. Add it in to match
the cleanup code in rtl8152_disconnect().
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a5feba71ec9c14a54c3babdc732c5b6866d8ee43 ]
According to the comment next to USB_CTRL_GET_TIMEOUT and
USB_CTRL_SET_TIMEOUT, although sending/receiving control messages is
usually quite fast, the spec allows them to take up to 5 seconds.
Let's increase the timeout in the Realtek driver from 500ms to 5000ms
(using the #defines) to account for this.
This is not just a theoretical change. The need for the longer timeout
was seen in testing. Specifically, if you drop a sc7180-trogdor based
Chromebook into the kdb debugger and then "go" again after sitting in
the debugger for a while, the next USB control message takes a long
time. Out of ~40 tests the slowest USB control message was 4.5
seconds.
While dropping into kdb is not exactly an end-user scenario, the above
is similar to what could happen due to an temporary interrupt storm,
what could happen if there was a host controller (HW or SW) issue, or
what could happen if the Realtek device got into a confused state and
needed time to recover.
This change is fairly critical since the r8152 driver in Linux doesn't
expect register reads/writes (which are backed by USB control
messages) to fail.
Fixes: ac718b6930 ("net/usb: new driver for RTL8152")
Suggested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a7b8d60b37237680009dd0b025fe8c067aba0ee3 ]
According to the document of napi, there is no rx process when the
budget is 0. Therefore, r8152_poll() has to return 0 directly when the
budget is equal to 0.
Fixes: d2187f8e44 ("r8152: divide the tx and rx bottom functions")
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7e01c7f7046efc2c7c192c3619db43292b98e997 upstream.
Currently in cdc_ncm_check_tx_max(), if dwNtbOutMaxSize is lower than
the calculated "min" value, but greater than zero, the logic sets
tx_max to dwNtbOutMaxSize. This is then used to allocate a new SKB in
cdc_ncm_fill_tx_frame() where all the data is handled.
For small values of dwNtbOutMaxSize the memory allocated during
alloc_skb(dwNtbOutMaxSize, GFP_ATOMIC) will have the same size, due to
how size is aligned at alloc time:
size = SKB_DATA_ALIGN(size);
size += SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
Thus we hit the same bug that we tried to squash with
commit 2be6d4d16a084 ("net: cdc_ncm: Allow for dwNtbOutMaxSize to be unset or zero")
Low values of dwNtbOutMaxSize do not cause an issue presently because at
alloc_skb() time more memory (512b) is allocated than required for the
SKB headers alone (320b), leaving some space (512b - 320b = 192b)
for CDC data (172b).
However, if more elements (for example 3 x u64 = [24b]) were added to
one of the SKB header structs, say 'struct skb_shared_info',
increasing its original size (320b [320b aligned]) to something larger
(344b [384b aligned]), then suddenly the CDC data (172b) no longer
fits in the spare SKB data area (512b - 384b = 128b).
Consequently the SKB bounds checking semantics fails and panics:
skbuff: skb_over_panic: text:ffffffff831f755b len:184 put:172 head:ffff88811f1c6c00 data:ffff88811f1c6c00 tail:0xb8 end:0x80 dev:<NULL>
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:113!
invalid opcode: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 57 Comm: kworker/0:2 Not tainted 5.15.106-syzkaller-00249-g19c0ed55a470 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 04/14/2023
Workqueue: mld mld_ifc_work
RIP: 0010:skb_panic net/core/skbuff.c:113 [inline]
RIP: 0010:skb_over_panic+0x14c/0x150 net/core/skbuff.c:118
[snip]
Call Trace:
<TASK>
skb_put+0x151/0x210 net/core/skbuff.c:2047
skb_put_zero include/linux/skbuff.h:2422 [inline]
cdc_ncm_ndp16 drivers/net/usb/cdc_ncm.c:1131 [inline]
cdc_ncm_fill_tx_frame+0x11ab/0x3da0 drivers/net/usb/cdc_ncm.c:1308
cdc_ncm_tx_fixup+0xa3/0x100
Deal with too low values of dwNtbOutMaxSize, clamp it in the range
[USB_CDC_NCM_NTB_MIN_OUT_SIZE, CDC_NCM_NTB_MAX_SIZE_TX]. We ensure
enough data space is allocated to handle CDC data by making sure
dwNtbOutMaxSize is not smaller than USB_CDC_NCM_NTB_MIN_OUT_SIZE.
Fixes: 289507d336 ("net: cdc_ncm: use sysfs for rx/tx aggregation tuning")
Cc: stable@vger.kernel.org
Reported-by: syzbot+9f575a1f15fc0c01ed69@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?extid=b982f1059506db48409d
Link: https://lore.kernel.org/all/20211202143437.1411410-1-lee.jones@linaro.org/
Signed-off-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230517133808.1873695-2-tudor.ambarus@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 43ffe6caccc7a1bb9d7442fbab521efbf6c1378c ]
Packet length check needs to be located after size and align_count
calculation to prevent kernel panic in skb_pull() in case
rx_cmd_a & RX_CMD_A_RED evaluates to true.
Fixes: d8b228318935 ("net: usb: smsc75xx: Limit packet length to skb->len")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20230316110540.77531-1-szymon.heidrich@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d8b228318935044dafe3a5bc07ee71a1f1424b8d ]
Packet length retrieved from skb data may be larger than
the actual socket buffer length (up to 9026 bytes). In such
case the cloned skb passed up the network stack will leak
kernel memory contents.
Fixes: d0cad87170 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e57cf3639c323eeed05d3725fd82f91b349adca8 ]
Move the LAN7800 internal phy (phy ID 0x0007c132) specific register
accesses to the phy driver (microchip.c).
Fix the error reported by Enguerrand de Ribaucourt in December 2022,
"Some operations during the cable switch workaround modify the register
LAN88XX_INT_MASK of the PHY. However, this register is specific to the
LAN8835 PHY. For instance, if a DP8322I PHY is connected to the LAN7801,
that register (0x19), corresponds to the LED and MAC address
configuration, resulting in unapropriate behavior."
I did not test with the DP8322I PHY, but I tested with an EVB-LAN7800
with the internal PHY.
Fixes: 14437e3fa2 ("lan78xx: workaround of forced 100 Full/Half duplex mode error")
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230301154307.30438-1-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06cd7c46b3ab3f2252c61bf85b191236cf0254e1 ]
Fixes the following W=1 kernel build warning(s):
drivers/net/usb/lan78xx.c: In function ‘lan78xx_read_raw_otp’:
drivers/net/usb/lan78xx.c:825:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_write_raw_otp’:
drivers/net/usb/lan78xx.c:879:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_deferred_multicast_write’:
drivers/net/usb/lan78xx.c:1041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_update_flowcontrol’:
drivers/net/usb/lan78xx.c:1127:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_init_mac_address’:
drivers/net/usb/lan78xx.c:1666:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_link_status_change’:
drivers/net/usb/lan78xx.c:1841:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_irq_bus_sync_unlock’:
drivers/net/usb/lan78xx.c:1920:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan8835_fixup’:
drivers/net/usb/lan78xx.c:1994:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_rx_max_frame_length’:
drivers/net/usb/lan78xx.c:2192:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_change_mtu’:
drivers/net/usb/lan78xx.c:2270:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_mac_addr’:
drivers/net/usb/lan78xx.c:2299:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_features’:
drivers/net/usb/lan78xx.c:2333:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
drivers/net/usb/lan78xx.c: In function ‘lan78xx_set_suspend’:
drivers/net/usb/lan78xx.c:3807:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201102114512.1062724-25-lee.jones@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Stable-dep-of: e57cf3639c32 ("net: lan78xx: fix accessing the LAN7800's internal phy specific registers from the MAC driver")
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c68f345b7c425b38656e1791a0486769a8797016 upstream.
syzbot reported that act_len in kalmia_send_init_packet() is
uninitialized when passing it to the first usb_bulk_msg error path. Jiri
Pirko noted that it's pointless to pass it in the error path, and that
the value that would be printed in the second error path would be the
value of act_len from the first call to usb_bulk_msg.[1]
With this in mind, let's just not pass act_len to the usb_bulk_msg error
paths.
1: https://lore.kernel.org/lkml/Y9pY61y1nwTuzMOa@nanopsycho/
Fixes: d40261236e ("net/usb: Add Samsung Kalmia driver for Samsung GT-B3730")
Reported-and-tested-by: syzbot+cd80c5ef5121bfe85b55@syzkaller.appspotmail.com
Signed-off-by: Miko Larsson <mikoxyzzz@gmail.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ecf7cf8efb59789e2b21d2f9ab926142579092b2 ]
Packet len computed as difference of length word extracted from
skb data and four may result in a negative value. In such case
processing of the buffer should be interrupted rather than
setting sr_skb->len to an unexpectedly large value (due to cast
from signed to unsigned integer) and passing sr_skb to
usbnet_skb_return.
Fixes: e9da0b56fe27 ("sr9700: sanity check for packet length")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20230114182326.30479-1-szymon.heidrich@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit c7dd13805f8b8fc1ce3b6d40f6aff47e66b72ad2 ]
Variables off and len typed as uint32 in rndis_query function
are controlled by incoming RNDIS response message thus their
value may be manipulated. Setting off to a unexpectetly large
value will cause the sum with len and 8 to overflow and pass
the implemented validation step. Consequently the response
pointer will be referring to a location past the expected
buffer boundaries allowing information leakage e.g. via
RNDIS_OID_802_3_PERMANENT_ADDRESS OID.
Fixes: ddda086240 ("USB: rndis_host, various cleanups")
Signed-off-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a487069e11b6527373f7c6f435d8998051d0b5d9 ]
Add RmNet support for LARA-L6.
LARA-L6 module can be configured (by AT interface) in three different
USB modes:
* Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial
interfaces
* RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial
interfaces and 1 RmNet virtual network interface
* CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial
interface and 1 CDC-ECM virtual network interface
In RmNet mode LARA-L6 exposes the following interfaces:
If 0: Diagnostic
If 1: AT parser
If 2: AT parser
If 3: AT parset/alternative functions
If 4: RMNET interface
Signed-off-by: Davide Tronchin <davide.tronchin.94@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7b960c967f2aa01ab8f45c5a0bd78e754cffdeee ]
Commit 05b35e7eb9 ("smsc95xx: add phylib support") amended
smsc95xx_resume() to call phy_init_hw(). That function waits for the
device to runtime resume even though it is placed in the runtime resume
path, causing a deadlock.
The problem is that phy_init_hw() calls down to smsc95xx_mdiobus_read(),
which never uses the _nopm variant of usbnet_read_cmd().
Commit b4df480f68 ("usbnet: smsc95xx: add reset_resume function with
reset operation") causes a similar deadlock on resume if the device was
already runtime suspended when entering system sleep:
That's because the commit introduced smsc95xx_reset_resume(), which
calls down to smsc95xx_reset(), which neglects to use _nopm accessors.
Fix by auto-detecting whether a device access is performed by the
suspend/resume task_struct and use the _nopm variant if so. This works
because the PM core guarantees that suspend/resume callbacks are run in
task context.
Stacktrace for posterity:
INFO: task kworker/2:1:49 blocked for more than 122 seconds.
Workqueue: usb_hub_wq hub_event
schedule
rpm_resume
__pm_runtime_resume
usb_autopm_get_interface
usbnet_read_cmd
__smsc95xx_read_reg
__smsc95xx_phy_wait_not_busy
__smsc95xx_mdio_read
smsc95xx_mdiobus_read
__mdiobus_read
mdiobus_read
smsc_phy_reset
phy_init_hw
smsc95xx_resume
usb_resume_interface
usb_resume_both
usb_runtime_resume
__rpm_callback
rpm_callback
rpm_resume
__pm_runtime_resume
usb_autoresume_device
hub_event
process_one_work
Fixes: b4df480f68 ("usbnet: smsc95xx: add reset_resume function with reset operation")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.16+
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1bd3a383075c64d638e65d263c9267b08ee7733c upstream.
The Lenovo OneLink+ Dock contains an RTL8153 controller that behaves as
a broken CDC device by default. Add the custom Lenovo PID to the r8152
driver to support it properly.
Also, systems compatible with this dock provide a BIOS option to enable
MAC address passthrough (as per Lenovo document "ThinkPad Docking
Solutions 2017"). Add the custom PID to the MAC passthrough list too.
Tested on a ThinkPad 13 1st gen with the expected results:
passthrough disabled: Invalid header when reading pass-thru MAC addr
passthrough enabled: Using pass-thru MAC addr XX:XX:XX:XX:XX:XX
Signed-off-by: Jean-Francois Le Fillatre <jflf_kernel@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 8960f878e39fadc03d74292a6731f1e914cf2019 ]
When a PHY interrupt is signaled, the SMSC LAN95xx driver updates the
MAC full duplex mode and PHY flow control registers based on cached data
in struct phy_device:
smsc95xx_status() # raises EVENT_LINK_RESET
usbnet_deferred_kevent()
smsc95xx_link_reset() # uses cached data in phydev
Simultaneously, phylib polls link status once per second and updates
that cached data:
phy_state_machine()
phy_check_link_status()
phy_read_status()
lan87xx_read_status()
genphy_read_status() # updates cached data in phydev
If smsc95xx_link_reset() wins the race against genphy_read_status(),
the registers may be updated based on stale data.
E.g. if the link was previously down, phydev->duplex is set to
DUPLEX_UNKNOWN and that's what smsc95xx_link_reset() will use, even
though genphy_read_status() may update it to DUPLEX_FULL afterwards.
PHY interrupts are currently only enabled on suspend to trigger wakeup,
so the impact of the race is limited, but we're about to enable them
perpetually.
Avoid the race by delaying execution of smsc95xx_link_reset() until
phy_state_machine() has done its job and calls back via
smsc95xx_handle_link_change().
Signaling EVENT_LINK_RESET on wakeup is not necessary because phylib
picks up link status changes through polling. So drop the declaration
of a ->link_reset() callback.
Note that the semicolon on a line by itself added in smsc95xx_status()
is a placeholder for a function call which will be added in a subsequent
commit. That function call will actually handle the INT_ENP_PHY_INT_
interrupt.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3108871f19221372b251f7da1ac38736928b5b3a ]
Upon receiving data from the Interrupt Endpoint, the SMSC LAN95xx driver
attempts to clear the signaled interrupts by writing "all ones" to the
Interrupt Status Register.
However the driver only ever enables a single type of interrupt, namely
the PHY Interrupt. And according to page 119 of the LAN950x datasheet,
its bit in the Interrupt Status Register is read-only. There's no other
way to clear it than in a separate PHY register:
https://www.microchip.com/content/dam/mchp/documents/UNG/ProductDocuments/DataSheets/LAN950x-Data-Sheet-DS00001875D.pdf
Consequently, writing "all ones" to the Interrupt Status Register is
pointless and can be dropped.
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de> # LAN9514/9512/9500
Tested-by: Ferry Toth <fntoth@gmail.com> # LAN9514
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit a69e617e533edddf3fa3123149900f36e0a6dc74 upstream.
usbnet uses the work usbnet_deferred_kevent() to perform tasks which may
sleep. On disconnect, completion of the work was originally awaited in
->ndo_stop(). But in 2003, that was moved to ->disconnect() by historic
commit "[PATCH] USB: usbnet, prevent exotic rtnl deadlock":
https://git.kernel.org/tglx/history/c/0f138bbfd83c
The change was made because back then, the kernel's workqueue
implementation did not allow waiting for a single work. One had to wait
for completion of *all* work by calling flush_scheduled_work(), and that
could deadlock when waiting for usbnet_deferred_kevent() with rtnl_mutex
held in ->ndo_stop().
The commit solved one problem but created another: It causes a
use-after-free in USB Ethernet drivers aqc111.c, asix_devices.c,
ax88179_178a.c, ch9200.c and smsc75xx.c:
* If the drivers receive a link change interrupt immediately before
disconnect, they raise EVENT_LINK_RESET in their (non-sleepable)
->status() callback and schedule usbnet_deferred_kevent().
* usbnet_deferred_kevent() invokes the driver's ->link_reset() callback,
which calls netif_carrier_{on,off}().
* That in turn schedules the work linkwatch_event().
Because usbnet_deferred_kevent() is awaited after unregister_netdev(),
netif_carrier_{on,off}() may operate on an unregistered netdev and
linkwatch_event() may run after free_netdev(), causing a use-after-free.
In 2010, usbnet was changed to only wait for a single instance of
usbnet_deferred_kevent() instead of *all* work by commit 23f333a2bf
("drivers/net: don't use flush_scheduled_work()").
Unfortunately the commit neglected to move the wait back to
->ndo_stop(). Rectify that omission at long last.
Reported-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/netdev/CAG48ez0MHBbENX5gCdHAUXZ7h7s20LnepBF-pa5M=7Bi-jZrEA@mail.gmail.com/
Reported-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/netdev/20220315113841.GA22337@pengutronix.de/
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/d1c87ebe9fc502bffcd1576e238d685ad08321e4.1655987888.git.lukas@wunner.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 36a15e1cb134c0395261ba1940762703f778438c upstream.
The extra byte inserted by usbnet.c when
(length % dev->maxpacket == 0) is causing problems to device.
This patch sets FLAG_SEND_ZLP to avoid this.
Tested with: 0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Problems observed:
======================================================================
1) Using ssh/sshfs. The remote sshd daemon can abort with the message:
"message authentication code incorrect"
This happens because the tcp message sent is corrupted during the
USB "Bulk out". The device calculate the tcp checksum and send a
valid tcp message to the remote sshd. Then the encryption detects
the error and aborts.
2) NETDEV WATCHDOG: ... (ax88179_178a): transmit queue 0 timed out
3) Stop normal work without any log message.
The "Bulk in" continue receiving packets normally.
The host sends "Bulk out" and the device responds with -ECONNRESET.
(The netusb.c code tx_complete ignore -ECONNRESET)
Under normal conditions these errors take days to happen and in
intense usage take hours.
A test with ping gives packet loss, showing that something is wrong:
ping -4 -s 462 {destination} # 462 = 512 - 42 - 8
Not all packets fail.
My guess is that the device tries to find another packet starting
at the extra byte and will fail or not depending on the next
bytes (old buffer content).
======================================================================
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e65af5403e462ccd7dff6a045a886c64da598c2e upstream.
usbnet provides some helper functions that are also used in
the context of reset() operations. During a reset the other
drivers on a device are unable to operate. As that can be block
drivers, a driver for another interface cannot use paging
in its memory allocations without risking a deadlock.
Use GFP_NOIO in the helpers.
Fixes: 877bd862f3 ("usbnet: introduce usbnet 3 command helpers")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20220628093517.7469-1-oneukum@suse.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f8ebb3ac881b17712e1d5967c97ab1806b16d3d6 upstream.
This patch corrects packet receiving in ax88179_rx_fixup.
- problem observed:
ifconfig shows allways a lot of 'RX Errors' while packets
are received normally.
This occurs because ax88179_rx_fixup does not recognise properly
the usb urb received.
The packets are normally processed and at the end, the code exits
with 'return 0', generating RX Errors.
(pkt_cnt==-2 and ptk_hdr over field rx_hdr trying to identify
another packet there)
This is a usb urb received by "tcpdump -i usbmon2 -X" on a
little-endian CPU:
0x0000: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
^ packet 1 start (pkt_len = 0x05ec)
^^^^ IP alignment pseudo header
^ ethernet packet start
last byte ethernet packet v
padding (8-bytes aligned) vvvv vvvv
0x05e0: c92d d444 1420 8a69 83dd 272f e82b 9811
0x05f0: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
... ^ packet 2
0x0be0: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
...
0x1130: 9d41 9171 8a38 0ec5 eeee f8e3 3b19 87a0
...
0x1720: 8cfc 15ff 5e4c e85c eeee f8e3 3b19 87a0
...
0x1d10: ecfa 2a3a 19ab c78c eeee f8e3 3b19 87a0
...
0x2070: eeee f8e3 3b19 87a0 94de 80e3 daac 0800
... ^ packet 7
0x2120: 7c88 4ca5 5c57 7dcc 0d34 7577 f778 7e0a
0x2130: f032 e093 7489 0740 3008 ec05 0000 0080
====1==== ====2====
hdr_off ^
pkt_len = 0x05ec ^^^^
AX_RXHDR_*=0x00830 ^^^^ ^
pkt_len = 0 ^^^^
AX_RXHDR_DROP_ERR=0x80000000 ^^^^ ^
0x2140: 3008 ec05 0000 0080 3008 5805 0000 0080
0x2150: 3008 ec05 0000 0080 3008 ec05 0000 0080
0x2160: 3008 5803 0000 0080 3008 c800 0000 0080
===11==== ===12==== ===13==== ===14====
0x2170: 0000 0000 0e00 3821
^^^^ ^^^^ rx_hdr
^^^^ pkt_cnt=14
^^^^ hdr_off=0x2138
^^^^ ^^^^ padding
The dump shows that pkt_cnt is the number of entrys in the
per-packet metadata. It is "2 * packet count".
Each packet have two entrys. The first have a valid
value (pkt_len and AX_RXHDR_*) and the second have a
dummy-header 0x80000000 (pkt_len=0 with AX_RXHDR_DROP_ERR).
Why exists dummy-header for each packet?!?
My guess is that this was done probably to align the
entry for each packet to 64-bits and maintain compatibility
with old firmware.
There is also a padding (0x00000000) before the rx_hdr to
align the end of rx_hdr to 64-bit.
Note that packets have a alignment of 64-bits (8-bytes).
This patch assumes that the dummy-header and the last
padding are optional. So it preserves semantics and
recognises the same valid packets as the current code.
This patch was made using only the dumpfile information and
tested with only one device:
0b95:1790 ASIX Electronics Corp. AX88179 Gigabit Ethernet
Fixes: 57bc3d3ae8c1 ("net: usb: ax88179_178a: Fix out-of-bounds accesses in RX fixup")
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Signed-off-by: Jose Alonso <joalonsof@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Link: https://lore.kernel.org/r/d6970bb04bf67598af4d316eaeb1792040b18cfd.camel@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit afb8e246527536848b9b4025b40e613edf776a9d ]
aqc111_rx_fixup() contains several out-of-bounds accesses that can be
triggered by a malicious (or defective) USB device, in particular:
- The metadata array (desc_offset..desc_offset+2*pkt_count) can be out of bounds,
causing OOB reads and (on big-endian systems) OOB endianness flips.
- A packet can overlap the metadata array, causing a later OOB
endianness flip to corrupt data used by a cloned SKB that has already
been handed off into the network stack.
- A packet SKB can be constructed whose tail is far beyond its end,
causing out-of-bounds heap data to be considered part of the SKB's
data.
Found doing variant analysis. Tested it with another driver (ax88179_178a), since
I don't have a aqc111 device to test it, but the code looks very similar.
Signed-off-by: Marcin Kozlowski <marcinguy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c70c453abcbf3ecbaadd4c3236a5119b8da365cf upstream.
According to Documentation/driver-api/usb/URB.rst when a device
is unplugged usb_submit_urb() returns -ENODEV.
This error code propagates all the way up to usbnet_read_cmd() and
usbnet_write_cmd() calls inside the smsc95xx.c driver during
Ethernet cable unplug, unbind or reboot.
This causes the following errors to be shown on reboot, for example:
ci_hdrc ci_hdrc.1: remove, state 1
usb usb2: USB disconnect, device number 1
usb 2-1: USB disconnect, device number 2
usb 2-1.1: USB disconnect, device number 3
smsc95xx 2-1.1:1.0 eth1: unregister 'smsc95xx' usb-ci_hdrc.1-1.1, smsc95xx USB 2.0 Ethernet
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: Failed to read reg index 0x00000114: -19
smsc95xx 2-1.1:1.0 eth1: Error reading MII_ACCESS
smsc95xx 2-1.1:1.0 eth1: __smsc95xx_mdio_read: MII is busy
smsc95xx 2-1.1:1.0 eth1: hardware isn't capable of remote wakeup
usb 2-1.4: USB disconnect, device number 4
ci_hdrc ci_hdrc.1: USB bus 2 deregistered
ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
imx2-wdt 30280000.watchdog: Device shutdown: Expect reboot!
reboot: Restarting system
Ignore the -ENODEV errors inside __smsc95xx_mdio_read() and
__smsc95xx_phy_wait_not_busy() and do not print error messages
when -ENODEV is returned.
Fixes: a049a30fc27c ("net: usb: Correct PHY handling of smsc95xx")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 21e8a96377e6b6debae42164605bf9dcbe5720c5 ]
Add quirk CDC_MBIM_FLAG_AVOID_ALTSETTING_TOGGLE for Telit FN990
0x1071 composition in order to avoid bind error.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d2b1a1ec9f559d30b724877da4ce592edc41fdc upstream.
A broken device may give an extreme offset like 0xFFF0
and a reasonable length for a fragment. In the sanity
check as formulated now, this will create an integer
overflow, defeating the sanity check. Both offset
and offset + len need to be checked in such a manner
that no overflow can occur.
And those quantities should be unsigned.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
