[ Upstream commit f816b9829b19394d318e01953aa3b2721bca040d ]
In the (unlikely) event that pm_runtime_get() (disguised as
pm_runtime_resume_and_get()) fails, the remove callback returned an
error early. The problem with this is that the driver core ignores the
error value and continues removing the device. This results in a
resource leak. Worse the devm allocated resources are freed and so if a
callback of the driver is called later the register mapping is already
gone which probably results in a crash.
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230510200020.1534610-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 06a4df5863f73af193a4ff7abf7cb04058584f06 ]
The ndo_start_xmit() method must not free skb when returning
NETDEV_TX_BUSY, since caller is going to requeue freed skb.
Fix it by returning NETDEV_TX_OK in case of dma_map_single() fails.
Fixes: 79f339125e ("net: fec: Add software TSO support")
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0a8b43b12dd78daa77a7dc007b92770d262a2714 ]
Using 'ethtool -d […]' on an i.MX6UL leads to a kernel crash:
Unhandled fault: external abort on non-linefetch (0x1008) at […]
due to this SoC has less registers in its FEC implementation compared to other
i.MX6 variants. Thus, a run-time decision is required to avoid access to
non-existing registers.
Fixes: a51d3ab507 ("net: fec: use a more proper compatible string for i.MX6UL type device")
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20221024080552.21004-1-jbe@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit b5bd95d17102b6719e3531d627875b9690371383 upstream.
Background:
We have a customer is running a Profinet stack on the 8MM which receives and
responds PNIO packets every 4ms and PNIO-CM packets every 40ms. However, from
time to time the received PNIO-CM package is "stock" and is only handled when
receiving a new PNIO-CM or DCERPC-Ping packet (tcpdump shows the PNIO-CM and
the DCERPC-Ping packet at the same time but the PNIO-CM HW timestamp is from
the expected 40 ms and not the 2s delay of the DCERPC-Ping).
After debugging, we noticed PNIO, PNIO-CM and DCERPC-Ping packets would
be handled by different RX queues.
The root cause should be driver ack all queues' interrupt when handle a
specific queue in fec_enet_rx_queue(). The blamed patch is introduced to
receive as much packets as possible once to avoid interrupt flooding.
But it's unreasonable to clear other queues'interrupt when handling one
queue, this patch tries to fix it.
Fixes: ed63f1dcd5 (net: fec: clear receive interrupts before processing a packet)
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Reported-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20211206135457.15946-1-qiangqing.zhang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 44712965bf12ae1758cec4de53816ed4b914ca1a ]
Smatch says:
drivers/net/ethernet/freescale/fec_main.c:3994 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
drivers/net/ethernet/freescale/fec_main.c:3995 fec_drv_remove() error: Using fep after free_{netdev,candev}(ndev);
Since fep pointer is netdev private data, accessing it after free_netdev()
call can cause use-after-free bug. Fix it by moving free_netdev() call at
the end of the function
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: a31eda65ba ("net: fec: fix clock count mis-match")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 52c4a1a85f4b346c39c896c0168f4a843b3385ff ]
As we know that AVB is enabled by default, and the ENET IP design is
queue 0 for best effort, queue 1&2 for AVB Class A&B. Bandwidth of each
queue 1&2 set in driver is 50%, TX bandwidth fluctuated when selecting
tx queues randomly with FEC_QUIRK_HAS_AVB quirk available.
This patch adds ndo_select_queue callback to select queues for
transmitting to fix this issue. It will always return queue 0 if this is
not a vlan packet, and return queue 1 or 2 based on priority of vlan
packet.
You may complain that in fact we only use single queue for trasmitting
if we are not targeted to VLAN. Yes, but seems we have no choice, since
AVB is enabled when the driver probed, we can't switch this feature
dynamicly. After compare multiple queues to single queue, TX throughput
almost no improvement.
One way we can implemet is to configure the driver to multiple queues
with Round-robin scheme by default. Then add ndo_setup_tc callback to
enable/disable AVB feature for users. Unfortunately, ENET AVB IP seems
not follow the standard 802.1Qav spec. We only can program
DMAnCFG[IDLE_SLOPE] field to calculate bandwidth fraction. And idle
slope is restricted to certain valus (a total of 19). It's far away from
CBS QDisc implemented in Linux TC framework. If you strongly suggest to do
this, I think we only can support limited numbers of bandwidth and reject
others, but it's really urgly and wried.
With this patch, VLAN tagged packets route to queue 0/1/2 based on vlan
priority; VLAN untagged packets route to queue 0.
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reported-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 619fee9eb13b5d29e4267cb394645608088c28a8 ]
If the memory allocated for cbd_base is failed, it should
free the memory allocated for the queues, otherwise it causes
memory leak.
And if the memory allocated for the queues is failed, it can
return error directly.
Fixes: 59d0f74656 ("net: fec: init multi queue date structure")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
pm_runtime_get_sync() will increment pm usage at first and it will
resume the device later. If runtime of the device has error or
device is in inaccessible state(or other error state), resume
operation will fail. If we do not call put operation to decrease
the reference, it will result in reference count leak. Moreover,
this device cannot enter the idle state and always stay busy or other
non-idle state later. So we fixed it by replacing it with
pm_runtime_resume_and_get.
Fixes: 8fff755e9f ("net: fec: Ensure clocks are enabled while using mdio bus")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some (apparently older) versions of the FEC hardware block do not like
the MMFR register being cleared to avoid generation of MII events at
initialization time. The action of clearing this register results in no
future MII events being generated at all on the problem block. This means
the probing of the MDIO bus will find no PHYs.
Create a quirk that can be checked at the FECs MII init time so that
the right thing is done. The quirk is set as appropriate for the FEC
hardware blocks that are known to need this.
Fixes: f166f890c8 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO")
Signed-off-by: Greg Ungerer <gerg@linux-m68k.org>
Acked-by: Fugang Duan <fugand.duan@nxp.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Link: https://lore.kernel.org/r/20201028052232.1315167-1-gerg@linux-m68k.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Minor conflicts in net/mptcp/protocol.h and
tools/testing/selftests/net/Makefile.
In both cases code was added on both sides in the same place
so just keep both.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_reset_after_clk_enable() is always called with ndev->phydev,
however that pointer may be NULL even though the PHY device instance
already exists and is sufficient to perform the PHY reset.
This condition happens in fec_open(), where the clock must be enabled
first, then the PHY must be reset, and then the PHY IDs can be read
out of the PHY.
If the PHY still is not bound to the MAC, but there is OF PHY node
and a matching PHY device instance already, use the OF PHY node to
obtain the PHY device instance, and then use that PHY device instance
when triggering the PHY reset.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Richard Leitner <richard.leitner@skidata.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phy_reset_after_clk_enable() does a PHY reset, which means the PHY
loses its register settings. The fec_enet_mii_probe() starts the PHY
and does the necessary calls to configure the PHY via PHY framework,
and loads the correct register settings into the PHY. Therefore,
fec_enet_mii_probe() should be called only after the PHY has been
reset, not before as it is now.
Fixes: 1b0a83ac04 ("net: fec: add phy_reset_after_clk_enable() support")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Christoph Niedermaier <cniedermaier@dh-electronics.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Because clk_prepare_enable() and clk_disable_unprepare() already checked
NULL clock parameter, so the additional checks are unnecessary, just
remove them.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct the error path for regulator disable.
Fixes: 9269e5560b ("net: fec: add phy-reset-gpios PROBE_DEFER check")
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP reuseport conflict was a little bit tricky.
The net-next code, via bpf-next, extracted the reuseport handling
into a helper so that the BPF sk lookup code could invoke it.
At the same time, the logic for reuseport handling of unconnected
sockets changed via commit efc6b6f6c3
which changed the logic to carry on the reuseport result into the
rest of the lookup loop if we do not return immediately.
This requires moving the reuseport_has_conns() logic into the callers.
While we are here, get rid of inline directives as they do not belong
in foo.c files.
The other changes were cases of more straightforward overlapping
modifications.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix support for external PTP-aware devices such as DSA or PTP PHY:
Make sure we never time stamp tx packets when hardware time stamping
is disabled.
Check for PTP PHY being in use and then pass ioctls related to time
stamping of Ethernet packets to the PTP PHY rather than handle them
ourselves. In addition, disable our own hardware time stamping in this
case.
Fixes: 6605b730c0 ("FEC: Add time stamping code and a PTP hardware clock")
Signed-off-by: Sergey Organov <sorganov@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The FEC allocates 2K buffers, but looses some of it due to
alignment. It can however support an MTU bigger than the default. This
is particularly interesting when used in combination with Ethernet
switches supporting DSA, which have extra headers. The DSA core will
try to increase the MTU to support these extra headers. If the max
size defaults to that of standard Ethernet we get a warning. By
setting the max to what the driver actually supports, we avoid this
warning.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the ISR, we poll the event register for the queues in need of
service and then enter polled mode. After this point, the event
register will never be read again until we exit polled mode.
In a scenario where a UDP flow is routed back out through the same
interface, i.e. "router-on-a-stick" we'll typically only see an rx
queue event initially. Once we start to process the incoming flow
we'll be locked polled mode, but we'll never clean the tx rings since
that event is never caught.
Eventually the netdev watchdog will trip, causing all buffers to be
dropped and then the process starts over again.
Rework the NAPI poll to keep trying to consome the entire budget as
long as new events are coming in, making sure to service all rx/tx
queues, in priority order, on each pass.
Fixes: 4d494cdc92 ("net: fec: change data structure to support multiqueue")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Tested-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tlen field into struct tso_t, and change tso_start()
to return skb_transport_offset(skb) + tso->tlen
This removes from callers the need to use tcp_hdrlen(skb) and
will ease UDP segmentation offload addition.
v2: calls tso_start() earlier in otx2_sq_append_tso() [Jakub]
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable clk_ref failed, clk_ptp should be disabled rather than
clk_ref itself.
Signed-off-by: Liu Xiang <liuxiang_1999@126.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit da722186f6 (net: fec: set GPR bit on suspend by DT
configuration) set the GPR reigster offset and bit in driver for
wake on lan feature.
But it introduces two issues here:
- one SOC has two instances, they have different bit
- different SOCs may have different offset and bit
So to support wake-on-lan feature on other i.MX platforms, it should
configure the GPR reigster offset and bit from DT.
So the patch is to improve the commit da722186f6 (net: fec: set GPR
bit on suspend by DT configuration) to support multiple ethernet
instances on i.MX series.
v2:
* switch back to store the quirks bitmask in driver_data
v3:
* suggested by Sascha Hauer, use a struct fec_devinfo for
abstracting differences between different hardware variants,
it can give more freedom to describe the differences.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Measurements of the MDIO bus have shown that driving the MDIO bus
using interrupts is slow. Back to back MDIO transactions take about
90us, with 25us spent performing the transaction, and the remainder of
the time the bus is idle.
Replacing the completion interrupt with polled IO results in back to
back transactions of 40us. The polling loop waiting for the hardware
to complete the transaction takes around 28us. Which suggests
interrupt handling has an overhead of 50us, and polled IO nearly
halves this overhead, and doubles the MDIO performance.
Care has to be taken when setting the MII_SPEED register, or it can
trigger an MII event> That then upsets the polling, due to an
unexpected pending event.
Suggested-by: Chris Heally <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 29ae6bd1b0.
The commit breaks ethernet function on i.MX6SX, i.MX7D, i.MX8MM,
i.MX8MQ, and i.MX8QXP platforms. Boot yocto system by NFS mounting
rootfs will be failed with the commit.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change to polled IO for MDIO completion assumes that MII events
are only generated for MDIO transactions. However on some SoCs writing
to the MII_SPEED register can also trigger an MII event. As a result,
the next MDIO read has a pending MII event, and immediately reads the
data registers before it contains useful data. When the read does
complete, another MII event is posted, which results in the next read
also going wrong, and the cycle continues.
By writing 0 to the MII_DATA register before writing to the speed
register, this MII event for the MII_SPEED is suppressed, and polled
IO works as expected.
Fixes: 29ae6bd1b0 ("net: ethernet: fec: Replace interrupt driven MDIO with polled IO")
Reported-by: Andy Duan <fugang.duan@nxp.com>
Suggested-by: Andy Duan <fugang.duan@nxp.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
An MDIO transaction normally starts with 32 1s as a preamble. However
not all devices requires such a preamble. Add a device tree property
which allows the preamble to be suppressed. This will half the size of
the MDIO transaction, allowing faster transactions. But it should only
be used when all devices on the bus support suppressed preamble.
Suggested-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MDIO busses typically operate at 2.5MHz. However many devices can
operate at faster speeds. This then allows more MDIO transactions per
second, useful for Ethernet switch statistics, or Ethernet PHY TDR
data. Allow the bus speed to be configured, using the standard
"clock-frequency" property, which i2c busses use to indicate the bus
speed. Before using this property, ensure all devices on the bus do
actually support the requested clock speed.
Suggested-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Measurements of the MDIO bus have shown that driving the MDIO bus
using interrupts is slow. Back to back MDIO transactions take about
90us, with 25us spent performing the transaction, and the remainder of
the time the bus is idle.
Replacing the completion interrupt with polled IO results in back to
back transactions of 40us. The polling loop waiting for the hardware
to complete the transaction takes around 28us. Which suggests
interrupt handling has an overhead of 50us, and polled IO nearly
halves this overhead, and doubles the MDIO performance.
Suggested-by: Chris Heally <cphealy@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some SoCs, such as the i.MX6, it is necessary to set a bit
in the SoC level GPR register before suspending for wake on lan
to work.
The fec platform callback sleep_mode_enable was intended to allow this
but the platform implementation was NAK'd back in 2015 [1]
This means that, currently, wake on lan is broken on mainline for
the i.MX6 at least.
So implement the required bit setting in the fec driver by itself
by adding a new optional DT property indicating the GPR register
and adding the offset and bit information to the driver.
[1] https://www.spinics.net/lists/netdev/msg310922.html
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set ethtool_ops->supported_coalesce_params to let
the core reject unsupported coalescing parameters.
This driver did not previously reject unsupported parameters.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_set_coalesce() validates the previously set params
and if they are within range proceeds to apply the new ones.
The new ones, however, are not validated. This seems backwards,
probably a copy-paste error?
Compile tested only.
Fixes: d851b47b22 ("net: fec: add interrupt coalescence feature support")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set static versions because linux kernel is
released all together with same version applicable to the whole
code base.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After performing an unbind/bind operation the network is no longer
functional on i.MX6 (which has a single FEC instance):
# echo 2188000.ethernet > /sys/bus/platform/drivers/fec/unbind
# echo 2188000.ethernet > /sys/bus/platform/drivers/fec/bind
[ 10.756519] pps pps0: new PPS source ptp0
[ 10.792626] libphy: fec_enet_mii_bus: probed
[ 10.799330] fec 2188000.ethernet eth0: registered PHC device 1
# udhcpc -i eth0
udhcpc: started, v1.31.1
[ 14.985211] fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
[ 14.993140] libphy: PHY fixed-0:00 not found
[ 14.997643] fec 2188000.ethernet eth0: could not attach to PHY
On SoCs with two FEC instances there are some cases where one FEC instance
depends on the other one being present. One such example is i.MX28, which
has the following FEC dependency as noted in the comments:
/*
* The i.MX28 dual fec interfaces are not equal.
* Here are the differences:
*
* - fec0 supports MII & RMII modes while fec1 only supports RMII
* - fec0 acts as the 1588 time master while fec1 is slave
* - external phys can only be configured by fec0
*
* That is to say fec1 can not work independently. It only works
* when fec0 is working. The reason behind this design is that the
* second interface is added primarily for Switch mode.
*
* Because of the last point above, both phys are attached on fec0
* mdio interface in board design, and need to be configured by
* fec0 mii_bus.
*/
Prevent the unbind operation to avoid these issues.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ungrafting from PRIO bug fixes in net, when merged into net-next,
merge cleanly but create a build failure. The resolution used here is
from Petr Machata.
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to dump the FECs registers the clocks have to be ticking,
otherwise a data abort occurs. Add calls to runtime PM so they are
enabled and later disabled.
Fixes: e8fcfcd568 ("net: fec: optimize the clock management to save power")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f5489 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b0 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
pm_runtime_put_autosuspend in probe will call runtime suspend to
disable clks automatically if CONFIG_PM is defined. (If CONFIG_PM
is not defined, its implementation will be empty, then runtime
suspend will not be called.)
Therefore, we can call pm_runtime_get_sync to runtime resume it
first to enable clks, which matches the runtime suspend. (Only when
CONFIG_PM is defined, otherwise pm_runtime_get_sync will also be
empty, then runtime resume will not be called.)
Then it is fine to disable clks without causing clock count mis-match.
Fixes: c43eab3edd ("net: fec: add missed clk_disable_unprepare in remove")
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One conflict in the BPF samples Makefile, some fixes in 'net' whilst
we were converting over to Makefile.target rules in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before this change of_get_phy_mode() returned an enum,
phy_interface_t. On error, -ENODEV etc, is returned. If the result of
the function is stored in a variable of type phy_interface_t, and the
compiler has decided to represent this as an unsigned int, comparision
with -ENODEV etc, is a signed vs unsigned comparision.
Fix this problem by changing the API. Make the function return an
error, or 0 on success, and pass a pointer, of type phy_interface_t,
where the phy mode should be stored.
v2:
Return with *interface set to PHY_INTERFACE_MODE_NA on error.
Add error checks to all users of of_get_phy_mode()
Fixup a few reverse christmas tree errors
Fixup a few slightly malformed reverse christmas trees
v3:
Fix 0-day reported errors.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
Failed to get irq using name is NOT fatal as driver will use index
to get irq instead, use platform_get_irq_byname_optional() instead
of platform_get_irq_byname() to avoid below error message during
probe:
[ 0.819312] fec 30be0000.ethernet: IRQ int0 not found
[ 0.824433] fec 30be0000.ethernet: IRQ int1 not found
[ 0.829539] fec 30be0000.ethernet: IRQ int2 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointer bdp is being assigned with a value that is never
read, so the assignment is redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IEEE 802.3ae clause 45 defines a modified MDIO protocol that uses a two
staged access model in order to increase the address space.
This patch adds support for C45 MDIO read and write accesses, which are
used whenever the MII_ADDR_C45 flag in the regnum argument is set.
In case it is not set, C22 accesses are used as before.
Signed-off-by: Marco Hartmann <marco.hartmann@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
