[ Upstream commit 7c81582c0bccb4757186176f0ee12834597066ad ]
Nullify stmfx->vdd in case devm_regulator_get_optional() returns an error.
And simplify code by returning an error only if return code is not -ENODEV,
which means there is no vdd regulator and it is not an issue.
Fixes: d75846ed08e6 ("mfd: stmfx: Fix dev_err_probe() call in stmfx_chip_init()")
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20230609092804.793100-2-amelie.delaunay@foss.st.com
Signed-off-by: Lee Jones <lee@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 96da8f148396329ba769246cb8ceaa35f1ddfc48 ]
When dln2_setup_rx_urbs() in dln2_probe() fails, error out_free forgets
to call usb_put_dev() to decrease the refcount of dln2->usb_dev.
Fix this by adding usb_put_dev() in the error handling code of
dln2_probe().
Signed-off-by: Qiang Ning <qning0106@126.com>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20230330024353.4503-1-qning0106@126.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f376c479668557bcc2fd9e9fbc0f53e7819a11cd ]
It seems that this driver was developed based on preliminary documentation.
Report the correct names for all TQMxE39x variants, as they are used by
the released hardware revisions:
- Fix names for TQMxE39C1/C2 board IDs
- Distinguish TQMxE39M and TQMxE39S, which use the same board ID
The TQMxE39M/S are distinguished using the SAUC (Sanctioned Alternate
Uses Configuration) register of the GPIO controller. This also prepares
for the correct handling of the differences between the GPIO controllers
of our COMe and SMARC modules.
Fixes: 2f17dd34ff ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/aca9a7cb42a85181bcb456c437554d2728e708ec.1676892223.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3da48ccb1d0f3b53b1e8c9022edbedc2a6e3f50a ]
Add the board IDs for the TQMx110EB and the TQMxE40x family. All use a
24MHz LPC clock.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stable-dep-of: 051c69ff4f60 ("mfd: tqmx86: Specify IO port register range more precisely")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 16b2ad150f74db0eb91f445061f16140b5aaa650 ]
No TQMx90UC exists at the moment, and it is undecided whether ID 10 will
be used eventually (and if it is, how that SoM will be named).
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Stable-dep-of: 051c69ff4f60 ("mfd: tqmx86: Specify IO port register range more precisely")
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1be1b23696b3d4b0231c694f5e0767b4471d33a9 ]
The I2C_DETECT register is at IO port 0x1a7, which is outside the range
passed to devm_ioport_map() for io_base, and was only working because
there aren't actually any bounds checks for IO port accesses.
Extending the range does not seem like a good solution here, as it would
then conflict with the IO resource assigned to the I2C controller. As
this is just a one-off access during probe, use a simple inb() instead.
While we're at it, drop the unused define TQMX86_REG_I2C_INT_EN.
Fixes: 2f17dd34ff ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/e8300a30f0791afb67d79db8089fb6004855f378.1676892223.git.matthias.schiffer@ew.tq-group.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 75db7907355ca5e2ff606e9dd3e86b6c3a455fe2 ]
The mx25_tsadc_remove() function assumes all non-zero returns are success
but the platform_get_irq() function returns negative on error and
positive non-zero values on success. It never returns zero, but if it
did then treat that as a success.
Fixes: 18f7739379 ("mfd: fsl-imx25: Clean up irq settings during removal")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/YvTfkbVQWYKMKS/t@kili
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 128ac294e1b437cb8a7f2ff8ede1cde9082bddbe ]
None of the in-tree instantiations of struct t7l66xb_platform_data
provides a disable callback. So better don't dereference this function
pointer unconditionally. As there is no user, drop it completely instead
of calling it conditional.
This is a preparation for making platform remove callbacks return void.
Fixes: 1f192015ca ("mfd: driver for the T7L66XB TMIO SoC")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220530192430.2108217-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 311242c7703df0da14c206260b7e855f69cb0264 ]
It will cause null-ptr-deref when using 'res', if platform_get_resource()
returns NULL, so move using 'res' after devm_ioremap_resource() that
will check it to avoid null-ptr-deref.
And use devm_platform_get_and_ioremap_resource() to simplify code.
Fixes: b5e29aa880 ("mfd: davinci_voicecodec: Remove pointless #include")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220426030857.3539336-1-yangyingliang@huawei.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5d051cf94fd5834a1513aa77e542c49fd973988a ]
Flexcom IP embeds 3 other IPs: usart, i2c, spi and selects the operation
mode (usart, i2c, spi) via mode register (FLEX_MR). On i2c bus there might
be connected critical devices (like PMIC) which on suspend/resume should
be suspended/resumed at the end/beginning. i2c uses
.suspend_noirq/.resume_noirq for this kind of purposes. Align flexcom
to use .resume_noirq as it should be resumed before the embedded IPs.
Otherwise the embedded devices might behave badly.
Fixes: 7fdec11015 ("atmel_flexcom: Support resuming after a chip reset")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211028135138.3481166-3-claudiu.beznea@microchip.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit c9e143084d1a602f829115612e1ec79df3727c8b upstream.
The runtime PM callback may be called as soon as the runtime PM facility
is enabled and activated. It means that ->suspend() may be called before
we finish probing the device in the ACPI case. Hence, NULL pointer
dereference:
intel-lpss INT34BA:00: IRQ index 0 not found
BUG: kernel NULL pointer dereference, address: 0000000000000030
...
Workqueue: pm pm_runtime_work
RIP: 0010:intel_lpss_suspend+0xb/0x40 [intel_lpss]
To fix this, first try to register the device and only after that enable
runtime PM facility.
Fixes: 4b45efe852 ("mfd: Add support for Intel Sunrisepoint LPSS devices")
Reported-by: Orlando Chamberlain <redecorating@protonmail.com>
Reported-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Aditya Garg <gargaditya08@live.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20211101190008.86473-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit cdff1eda69326fb46de10c5454212b3efcf4bb41 ]
One MIPS platform (mach-rc32434) defines GPIOBASE. This macro
conflicts with one of the same name in lpc_sch.c. Rename the latter one
to prevent the build error.
../drivers/mfd/lpc_sch.c:25: error: "GPIOBASE" redefined [-Werror]
25 | #define GPIOBASE 0x44
../arch/mips/include/asm/mach-rc32434/rb.h:32: note: this is the location of the previous definition
32 | #define GPIOBASE 0x050000
Cc: Denis Turischev <denis@compulab.co.il>
Fixes: e82c60ae7d ("mfd: Introduce lpc_sch for Intel SCH LPC bridge")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 922e8ce883e59b52786b2c11656d84dc58ef084a ]
The IRQ support for SCH GPIO is not specific to the Intel Quark SoC.
Moreover the IRQ routing is quite interesting there, so while it's
needs a special support, the driver haven't it anyway yet.
Due to above remove basically redundant code of IRQ support.
This reverts commit ec689a8a81.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a946506c48f3bd09363c9d2b0a178e55733bcbb6 ]
The driver was registering IRQ 0 when no IRQ was set. This leads to
warnings with newer kernels.
Clear the resource flags, so no resource is registered at all in this
case.
Fixes: 2f17dd34ff ("mfd: tqmx86: IO controller with I2C, Wachdog and GPIO")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit f949a9ebce7a18005266b859a17f10c891bb13d7 ]
On Cherry Trail devices with an AXP288 PMIC the external SD-card slot
used the AXP's DLDO2 as card-voltage and either DLDO3 or GPIO1LDO
(GPIO1 pin in low noise LDO mode) as signal-voltage.
These regulators are turned on/off and in case of the signal-voltage
also have their output-voltage changed by the _PS0 and _PS3 power-
management ACPI methods on the MMC-controllers ACPI fwnode as well as
by the _DSM ACPI method for changing the signal voltage.
The AML code implementing these methods is directly accessing the
PMIC through ACPI I2C OpRegion accesses, instead of using the special
PMIC OpRegion handled by drivers/acpi/pmic/intel_pmic_xpower.c .
This means that the contents of the involved PMIC registers can change
without the change being made through the regmap interface, so regmap
should not cache the contents of these registers.
Mark the regulator power on/off, the regulator voltage control and the
GPIO1 control registers as volatile, to avoid regmap caching them.
Specifically this fixes an issue on some models where the i915 driver
toggles another LDO using the same on/off register on/off through
MIPI sequences (through intel_soc_pmic_exec_mipi_pmic_seq_element())
which then writes back a cached on/off register-value where the
card-voltage is off causing the external sdcard slot to stop working
when the screen goes blank, or comes back on again.
The regulator register-range now marked volatile also includes the
buck regulator control registers. This is done on purpose these are
normally not touched by the AML code, but they are updated directly
by the SoC's PUNIT which means that they may also change without going
through regmap.
Note the AXP288 PMIC is only used on Bay- and Cherry-Trail platforms,
so even though this is an ACPI specific problem there is no need to
make the new volatile ranges conditional since these platforms always
use ACPI.
Fixes: dc91c3b6fe ("mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile")
Fixes: cd53216625 ("mfd: axp20x: Fix axp288 volatile ranges")
Reported-and-tested-by: Clamshell <clamfly@163.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ff80e2de36d0554e3a6da18a171719fe8663c17 ]
Although irq_create_mapping() is able to deal with duplicate
mappings, it really isn't supposed to be a substitute for
irq_find_mapping(), and can result in allocations that take place
in atomic context if the mapping didn't exist.
Fix the handful of MFD drivers that use irq_create_mapping() in
interrupt context by using irq_find_mapping() instead.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ec343111c056ec3847800302f6dbc57281f833fa ]
These are the actual frequencies reported by the PLL, so let's
report these. The roundoffs are inappropriate, we should round
to the frequency that the clock will later report.
Drop some whitespace at the same time.
Cc: phone-devel@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0b7cbe811ca524295ea43d9a4d73d3427e419c54 ]
We have started to get a bunch of pointless dmamask not set warnings
that makes the output of dmesg -l err,warn hard to read with many
extra warnings:
cpcap-regulator cpcap-regulator.0: DMA mask not set
cpcap_adc cpcap_adc.0: DMA mask not set
cpcap_battery cpcap_battery.0: DMA mask not set
cpcap-charger cpcap-charger.0: DMA mask not set
cpcap-pwrbutton cpcap-pwrbutton.0: DMA mask not set
cpcap-led cpcap-led.0: DMA mask not set
cpcap-led cpcap-led.1: DMA mask not set
cpcap-led cpcap-led.2: DMA mask not set
cpcap-led cpcap-led.3: DMA mask not set
cpcap-led cpcap-led.4: DMA mask not set
cpcap-rtc cpcap-rtc.0: DMA mask not set
cpcap-usb-phy cpcap-usb-phy.0: DMA mask not set
This seems to have started with commit 4d8bde883b ("OF: Don't set
default coherent DMA mask"). We have the parent SPI controller use
DMA, while CPCAP driver and it's children do not. For audio, the
DMA is handled over I2S bus with the McBSP driver.
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Ivan Jelincic <parazyd@dyne.org>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Sicelo A. Mhlongo <absicsz@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4700ef326556ed74aba188f12396740a8c1c21dd ]
This patch adds/modifies MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 56a1188159cb2b87fbcb5a7a7afb38a4dd9db0c1 upstream.
The commit 529a1101212a("mfd: syscon: Don't free allocated name
for regmap_config") doesn't free the allocated name field of struct
regmap_config, but introduce a memory leak. There is another
commit 94cc89eb8fa5("regmap: debugfs: Fix handling of name string
for debugfs init delays") fixing this debugfs init issue from root
cause. With this fixing, the name field in struct regmap_debugfs_node
is removed. When initialize debugfs for syscon driver, the name
field of struct regmap_config is not used anymore. So, the allocated
name field of struct regmap_config is need to be freed directly after
regmap initialization to avoid memory leak.
Cc: stable@vger.kernel.org
Fixes: 529a1101212a("mfd: syscon: Don't free allocated name for regmap_config")
Signed-off-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a1649a5260631979c68e5b2012f60f90300e646f ]
During more massive generation of interrupts, the IRQ got stuck,
and the subdevices did not see any new interrupts. That happens
especially at wonky USB supply in combination with ADC reads.
To fix that trigger the IRQ at level low instead of falling edge.
Fixes: 0c81604516 ("mfd: rn5t618: Add IRQ support")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 4917e498c6894ba077867aff78f82cffd5ffbb5c ]
The ARR register is cleared unconditionally upon probing, after the maximum
value has been read. This initial condition is rather not intuitive, when
considering the counter child driver. It rather expects the maximum value
by default:
- The counter interface shows a zero value by default for 'ceiling'
attribute.
- Enabling the counter without any prior configuration makes it doesn't
count.
The reset value of ARR register is the maximum. So Choice here
is to backup it, and restore it then, instead of clearing its value.
It also fixes the initial condition seen by the counter driver.
Fixes: d0f949e220 ("mfd: Add STM32 Timers driver")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit fe6df2b48043bbe1e852b2320501d3b169363c35 ]
pm_runtime_get_sync() will increase the rumtime PM counter
even it returns an error. Thus a pairing decrement is needed
to prevent refcount leak. Fix this by replacing this API with
pm_runtime_resume_and_get(), which will not change the runtime
PM counter on error.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 586478bfc9f7e16504d6f64cf18bcbdf6fd0cbc9 ]
By default the PMIC DA9063 2-wire interface is SMBus compliant. This
means the PMIC will automatically reset the interface when the clock
signal ceases for more than the SMBus timeout of 35 ms.
If the I2C driver / device is not capable of creating atomic I2C
transactions, a context change can cause a ceasing of the clock signal.
This can happen if for example a real-time thread is scheduled. Then
the DA9063 in SMBus mode will reset the 2-wire interface. Subsequently
a write message could end up in the wrong register. This could cause
unpredictable system behavior.
The DA9063 PMIC also supports an I2C compliant mode for the 2-wire
interface. This mode does not reset the interface when the clock
signal ceases. Thus the problem depicted above does not occur.
This patch tests for the bus functionality "I2C_FUNC_I2C". It can
reasonably be assumed that the bus cannot obey SMBus timings if
this functionality is set. SMBus commands most probably are emulated
in this case which is prone to the latency issue described above.
This patch enables the I2C bus mode if I2C_FUNC_I2C is set or
otherwise keeps the default SMBus mode.
Signed-off-by: Hubert Streidl <hubert.streidl@de.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 8d9bf3c3e1451fc8de7b590040a868ade26d6b22 upstream.
The Gateworks System Controller has an active-low interrupt.
Fix the interrupt request type.
Cc: <stable@vger.kernel.org>
Fixes: d85234994b ("mfd: Add Gateworks System Controller core driver")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 26783d74cc6a440ee3ef9836a008a697981013d0 ]
The "req" struct is always added to the "wm831x->auxadc_pending" list,
but it's only removed from the list on the success path. If a failure
occurs then the "req" struct is freed but it's still on the list,
leading to a use after free.
Fixes: 78bb3688ea ("mfd: Support multiple active WM831x AUXADC conversions")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit b0b5b16b78cea1b2b990a69ab8e07a42ccf7a2ed ]
A recent fix improved the way the resource gets passed to
the low-level accessors, but left one warning that appears
in configurations with a resource_size_t that is wider than
a pointer:
In file included from drivers/mfd/altera-sysmgr.c:19:
drivers/mfd/altera-sysmgr.c: In function 'sysmgr_probe':
drivers/mfd/altera-sysmgr.c:148:40: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
148 | regmap = devm_regmap_init(dev, NULL, (void *)res->start,
| ^
include/linux/regmap.h:646:6: note: in definition of macro '__regmap_lockdep_wrapper'
646 | fn(__VA_ARGS__, &_key, \
| ^~~~~~~~~~~
drivers/mfd/altera-sysmgr.c:148:12: note: in expansion of macro 'devm_regmap_init'
148 | regmap = devm_regmap_init(dev, NULL, (void *)res->start,
| ^~~~~~~~~~~~~~~~
I had tried a different approach that would store the address
in the private data as a phys_addr_t, but the easiest solution
now seems to be to add a double cast to shut up the warning.
As the address is passed to an inline assembly, it is guaranteed
to not be wider than a register anyway.
Fixes: d9ca7801b6 ("mfd: altera-sysmgr: Fix physical address storing hacks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
