[ Upstream commit 39e8d062b03c3dc257d880d82bd55cdd9e185a3b ]
To comply with the panel sequence, hold the mipi signal to LP00 before
the dcs cmds transmission, and pull the mipi signal high from LP00 to
LP11 until the start of the dcs cmds transmission.
The normal panel timing is :
(1) pp1800 DC pull up
(2) avdd & avee AC pull high
(3) lcm_reset pull high -> pull low -> pull high
(4) Pull MIPI signal high (LP11) -> initial code -> send video data
(HS mode)
The power-off sequence is reversed.
If dsi is not in cmd mode, then dsi will pull the mipi signal high in
the mtk_output_dsi_enable function. The delay in lane_ready func is
the reaction time of dsi_rx after pulling up the mipi signal.
Fixes: 2dd8075d21 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge API")
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/1653012007-11854-4-git-send-email-xinlei.lee@mediatek.com/
Cc: <stable@vger.kernel.org> # 5.10.x: 7f6335c6a258: drm/mediatek: Modify dsi funcs to atomic operations
Cc: <stable@vger.kernel.org> # 5.10.x: cde7e2e35c28: drm/mediatek: Separate poweron/poweroff from enable/disable and define new funcs
Cc: <stable@vger.kernel.org> # 5.10.x
Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 81cc7e51c4f1686b71e30046437056ece6b2cb4d ]
Mipi dsi panel drivers can use mipi_dsi_dcs_{set,get}_display_brightness()
to request backlight changes.
This can be done during panel initialization (dsi is in command mode)
or afterwards (dsi is in Video Mode).
When the DSI is in Video Mode, all commands are rejected.
Detect current DSI mode in mtk_dsi_host_transfer() and switch modes
temporarily to allow commands to be sent.
Signed-off-by: Julien STEPHAN <jstephan@baylibre.com>
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 48b927770f8ad3f8cf4a024a552abf272af9f592 ]
In exynos7_decon_resume, When it fails, we must use clk_disable_unprepare()
to free resource that have been used.
Fixes: 6f83d20838 ("drm/exynos: use DRM_DEV_ERROR to print out error
message")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jian Zhang <zhangjian210@huawei.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 21779cc21c732c5eff8ea1624be6590450baa30f ]
The next call to sii8620_burst_get_tx_buf will result in off-by-one
When ctx->burst.tx_count + size == ARRAY_SIZE(ctx->burst.tx_buf). The same
thing happens in sii8620_burst_get_rx_buf.
This patch also change tx_count and tx_buf to rx_count and rx_buf in
sii8620_burst_get_rx_buf. It is unreasonable to check tx_buf's size and
use rx_buf.
Fixes: e19e9c692f ("drm/bridge/sii8620: add support for burst eMSC transmissions")
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220518065856.18936-1-hbh25y@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 0ee5a40152b15f200ed3a0d51e8aa782ea979c6a ]
Increase the number of post-sync blanking lines on odd fields instead of
decreasing it on even fields. This makes the total number of lines
properly match the modelines.
Additionally fix the value of PV_VCONTROL_ODD_DELAY, which did not take
pixels_per_clock into account, causing some displays to invert the
fields when driven by bcm2711.
Fixes: 682e62c454 ("drm/vc4: Fix support for interlaced modes on HDMI.")
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-31-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7bcb9c8d0bc9f3cab8ac2634b056c2e6b63945ca ]
vc4_dsi_encoder_disable is partially an open coded version of
drm_bridge_chain_disable, but it missed a termination condition
in the loop for ->disable which meant that no post_disable
calls were made.
Add in the termination clause.
Fixes: 033bfe7538 ("drm/vc4: dsi: Fix bridge chain handling")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-17-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d1d195ce26a14ec0a87816c09ae514e1c40e97f7 ]
Most of the differences between DSI0 and DSI1 are handled through the
ID. However, the BCM2711 DSI is going to introduce one more variable to
the mix and will break some expectations of the earlier, simpler, test.
Let's add a variant structure that will address most of the differences
between those three controllers.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203132543.861591-5-maxime@cerno.tech
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 3b45eee87da171caa28f61240ddb5c21170cda53 ]
The divider calculations tried to find the divider just faster than the
clock requested. However if it required a divider of 7 then the for loop
aborted without handling the "error" case, and could end up with a clock
lower than requested.
The integer divider from parent PLL to DSI clock is also capable of
going up to /255, not just /7 that the driver was trying. This allows
for slower link frequencies on the DSI bus where the resolution permits.
Correct the loop so that we always have a clock greater than requested,
and covering the whole range of dividers.
Fixes: 86c1b9eff3 ("drm/vc4: Adjust modes in DSI to work around the integer PLL divider.")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20220613144800.326124-13-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 517db1ab1566dba3093dbdb8de4263ba4aa66416 ]
There is little harm in ignoring fractional coordinates
(they just get truncated).
Without this:
modetest -M vc4 -F tiles,gradient -s 32:1920x1080-60 -P89@74:1920x1080*.1.1@XR24
is rejected. We have the same issue in Kodi when trying to
use zoom options on video.
Note: even if all coordinates are fully integer. e.g.
src:[0,0,1920,1080] dest:[-10,-10,1940,1100]
it will still get rejected as drm_atomic_helper_check_plane_state
uses drm_rect_clip_scaled which transforms this to fractional src coords
Fixes: 21af94cf1a ("drm/vc4: Add support for scaling of display planes.")
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Link: https://lore.kernel.org/r/20220613144800.326124-5-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9cc4853e4781bf0dd0f35355dc92d97c9da02f5d ]
Commit 680532c50b ("drm: adv7511: Add support for
i2c_new_secondary_device") allows a device tree node to override
the default addresses of the secondary i2c devices. This is useful
for solving address conflicts on the i2c bus.
In adv7511_init_cec_regmap() the new i2c address of cec device is
read from device tree and immediately accessed, well before it is
written in the proper register to override the default address.
This can cause an i2c error during probe and a consequent probe
failure.
Once the new i2c address is read from the device tree, override
the default address before any attempt to access the cec.
Tested with adv7533 and stm32mp157f.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Fixes: 680532c50b ("drm: adv7511: Add support for i2c_new_secondary_device")
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220607213144.427177-1-antonio.borneo@foss.st.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 136f614931a2bb73616b292cf542da3a18daefd5 ]
The last case label can write two buffers 'mc_reg_address[j]' and
'mc_data[j]' with 'j' offset equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE
since there are no checks for this value in both case labels after the
last 'j++'.
Instead of changing '>' to '>=' there, add the bounds check at the start
of the second 'case' (the first one already has it).
Also, remove redundant last checks for 'j' index bigger than array size.
The expression is always false. Moreover, before or after the patch
'table->last' can be equal to SMC_NISLANDS_MC_REGISTER_ARRAY_SIZE and it
seems it can be a valid value.
Detected using the static analysis tool - Svace.
Fixes: 69e0b57a91 ("drm/radeon/kms: add dpm support for cayman (v5)")
Signed-off-by: Alexey Kodanev <aleksei.kodanev@bell-sw.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 435c249008cba04ed6a7975e9411f3b934620204 ]
In __spi_validate, there's a validation that no partial transfers
are accepted (xfer->len % w_size must be zero). When
max_chunk is not a multiple of bpw (e.g. max_chunk = 65535,
bpw = 16), the transfer will be rejected.
This patch aligns max_chunk to 2 bytes (the maximum value of bpw is 16),
so that no partial transfer will occur.
Fixes: d23d4d4dac ("drm/tinydrm: Move tinydrm_spi_transfer()")
Signed-off-by: Yunhao Tian <t123yh.xyz@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510030219.2486687-1-t123yh.xyz@gmail.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9ad6f181ad9a19a26bda73a7b199df44ccfcdaba ]
The SPI core always reports a "MODALIAS=spi:<foo>", even if the device was
registered via OF. This means that the st7735r.ko module won't autoload if
a DT has a node with a compatible "okaya,rh128128t" string.
In that case, kmod expects a "MODALIAS=of:N*T*Cokaya,rh128128t" uevent but
instead will get a "MODALIAS=spi:rh128128t", which is not present in the
list of aliases:
$ modinfo drivers/gpu/drm/tiny/st7735r.ko | grep alias
alias: of:N*T*Cokaya,rh128128tC*
alias: of:N*T*Cokaya,rh128128t
alias: of:N*T*Cjianda,jd-t18003-t01C*
alias: of:N*T*Cjianda,jd-t18003-t01
alias: spi:jd-t18003-t01
To workaround this issue, add in the SPI table an entry for that device.
Fixes: d1d511d516 ("drm: tiny: st7735r: Add support for Okaya RH128128T")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: David Lechner <david@lechnology.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220520091602.179078-1-javierm@redhat.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit f5ba14043621f4afdf3ad5f92ee2d8dbebbe4340 upstream.
When pinning a buffer, we should check to see if there are any
additional restrictions imposed by bo->preferred_domains. This will
prevent the BO from being moved to an invalid domain when pinning.
For example, this can happen if the user requests to create a BO in GTT
domain for display scanout. amdgpu_dm will allow pinning to either VRAM
or GTT domains, since DCN can scanout from either or. However, in
amdgpu_bo_pin_restricted(), pinning to VRAM is preferred if there is
adequate carveout. This can lead to pinning to VRAM despite the user
requesting GTT placement for the BO.
v2: Allow the kernel to override the domain, which can happen when
exporting a BO to a V4L camera (for example).
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c96cfaf8fc02d4bb70727dfa7ce7841a3cff9be2 upstream.
While trying to fix another issue, it occurred to me that I don't actually
think there is any situation where we want pm_runtime_put() in nouveau to
be synchronous. In fact, this kind of just seems like it would cause
issues where we may unexpectedly block a thread we don't expect to be
blocked.
So, let's only use pm_runtime_put_autosuspend().
Changes since v1:
* Use pm_runtime_put_autosuspend(), not pm_runtime_put()
Signed-off-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: David Airlie <airlied@linux.ie>
Fixes: 3a6536c51d ("drm/nouveau: Intercept ACPI_VIDEO_NOTIFY_PROBE")
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org> # v4.10+
Link: https://patchwork.freedesktop.org/patch/msgid/20220714174234.949259-3-lyude@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit db2b927f8668adf3ac765e0921cd2720f5c04172 upstream.
The dmas property is used to hold the dmaengine channel used for audio
output.
Older device trees were missing that property, so if it's not there we
disable the audio output entirely.
However, some overlays have set an empty value to that property, mostly
to workaround the fact that overlays cannot remove a property. Let's add
a test for that case and if it's empty, let's disable it as well.
Cc: <stable@vger.kernel.org>
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Link: https://lore.kernel.org/r/20220613144800.326124-18-maxime@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 66cee9097e2b74ff3c8cc040ce5717c521a0c3fa upstream.
Users may request that pages from an OpenCL SVM allocation be migrated
to the GPU with clEnqueueSVMMigrateMem(). In Nouveau this will call into
nouveau_dmem_migrate_vma() to do the migration. If the total range to be
migrated exceeds SG_MAX_SINGLE_ALLOC the pages will be migrated in
chunks of size SG_MAX_SINGLE_ALLOC. However a typo in updating the
starting address means that only the first chunk will get migrated.
Fix the calculation so that the entire range will get migrated if
possible.
Signed-off-by: Alistair Popple <apopple@nvidia.com>
Fixes: e3d8b08904 ("drm/nouveau/svm: map pages after migration")
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220720062745.960701-1-apopple@nvidia.com
Cc: <stable@vger.kernel.org> # v5.8+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 3ce51649cdf23ab463494df2bd6d1e9529ebdc6a ]
Stutter mode is a power saving feature on GPUs, however at
least one early raven system exhibits stability issues with
it. Add a quirk to disable it for that system.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=214417
Fixes: 005440066f ("drm/amdgpu: enable gfxoff again on raven series (v2)")
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
