Yishai Hadas Says:
====================
Expose raw packet pacing APIs to be used by DEVX based applications. The
existing code was refactored to have a single flow with the new raw APIs.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Due to dependencies
* branch 'mlx5_packet_pacing':
IB/mlx5: Introduce UAPIs to manage packet pacing
net/mlx5: Expose raw packet pacing APIs
First batch of fixes intended for v5.6
* Fix a locking issue in time events handling;
* A fix in rate-scaling;
* Fix for a potential NULL pointer deref;
* Enable antenna diversity in some devices that were erroneously not
doing it;
* Allow FW dumps to continue when the FW is stuck;
* A fix in the HE capabilities handling;
* Another fix for FW dumps where we were reading wrong addresses.
Adds all the necessary logic so that stmmac can be used with Synopsys
DesignWare XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synopsys DesignWare XPCS is an MMD that can manage link status,
auto-negotiation, link training, ...
In this commit we add basic support for XPCS using USXGMII interface and
Clause 73 Auto-negotiation.
This is highly tied with PHYLINK and can't be used without it. A given
ethernet driver can use the provided callbacks to add the support for
XPCS.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We may have cases where MAC or PCS do not support Autoneg. Check if it
is supported after validate callback is called.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the stmmac ethernet driver to use the finalised link parameters
in mac_link_up() rather than the parameters in mac_config().
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_OF is not enabled, of_fwnode_handle() will return NULL, even
though we can have a FW handle from a given device.
Fallback to dev_fwnode() helper if needed.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the linkmode_and()/linkmode_andnot() helpers to simplify the code.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a PHY is not attached, we can still run the tests with MAC loopback
mode. Return -EOPNOTSUPP error code in PHY loopback test so that global
status is not a failure.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed says:
====================
mlx5-updates-2020-03-09
This series provides updates to mlx5 driver:
1) Use vport metadata matching only when mandatory
2) Introduce root flow table and ethtool steering for uplink representors
3) Expose port speed via FW when link modes are not available
3) Misc cleanups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Since kernel already has logs after kzalloc fails,
it's unnecessary to print duplicate logs. So this
patch deletes these logs.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies some printing relating to reset issue.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a local variable to save the command code in
some dump cases which need to modify the command code, then
the failing command code can be print out for debugging.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When received an unknown vector 0 interrupt, there is not a
helpful information for user to realize that now. So this patch
prints out the value of the status register for this case, and
uses dev_info() instead of dev_dbg() in hclge_check_event_cause().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When setting VF's MAC from PF, if the VF driver not loaded, the
firmware will return error to PF.
So PF should check whether VF is alive before sending message to
VF when setting VF's MAC.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hclge_add_mc_addr_common() and hclge_rm_mc_addr_common(),
variable req had been set as "0" by memset(), so it's unnecessary
to set .entry_type field as "0" with hnae3_set_bit() again.
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hclge_handle_hw_ras_error(), it is unnecessary to check
HCLGE_STATE_RST_HANDLING flag, because the reset priority
has been ensured by the process itself.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name of macro HCLGE_MAX_NCL_CONFIG_LENGTH is inaccurate,
this patch renames it to HCLGE_NCL_CONFIG_LENGTH_IN_EACH_CMD.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up some incorrect type in assignment reported by sparse
and compiler.
The warning as below:
- warning : restricted __le16 degrades to integer
- warning : cast from restricted __le32
- warning : cast from restricted __be32
- warning : cast from restricted __be16
and "mixed operation".
Signed-off-by: Guojia Liao <liaoguojia@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the management port device id. This is to
capture the device and set it up for devlink use, but not set
it up for network operations. We still use a netdev object
in order to use the napi infrasucture for processing adminq
and notifyq messages, we just don't register the netdev.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print the PCI bus lane information so people can keep an
eye out for poor configurations that might not support
the advertised speed.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can disable rxhashing by setting rss_types to 0. The user
can toggle this with "ethtool -K <ethX> rxhash off|on",
which calls into the .ndo_set_features callback with the
NETIF_F_RXHASH feature bit set or cleared. This patch adds
a check for that bit and updates the FW if necessary.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the unused flags field and and fix the bitflag names
to include the _F_ flag hint.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spreading the interrupts across the CPU cores is good for load
balancing, but not necessarily as good when using a CPU/core
that is not part of the NUMA local CPU. If it can be localized,
the kernel's cpumask_local_spread() service will pick a core
that is on the node close to the PCI device.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the misguided "#pragma packed" with tags on each
struct/union definition that actually needs it. This is safer
and more efficient on the various compilers and architectures.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the basic ionic interface works but the lif creation fails,
don't fail the probe. This will allow us to use the driver to
help inspect the hw/fw/pci interface for debugging purposes.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for configuring port mirroring through the cls_matchall
classifier. We do a full ingress and/or egress capture towards a
capture port.
MT7530 supports one monitor port and multiple mirrored ports.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until ae84bc1873 ("r8169: don't use bit LastFrag in tx descriptor
after send") we used to access another bit in the descriptor, therefore
it seems the barrier was needed. Since this commit DescOwn is the
only bit we're interested in, so the barrier isn't needed any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the parameters taken by rtl8169_unmap_tx_skb, this makes
usage of this function easier to read and understand.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far tx_skb->skb is the only member of the two structs that is not
reset. Make understanding the code easier by resetting both structs
completely in rtl8169_unmap_tx_skb.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slightly improve the code by converting this while to a for loop.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
What the driver writes into MAC_MAXLEN_CFG does not actually represent
VLAN_ETH_FRAME_LEN but instead ETH_FRAME_LEN + ETH_FCS_LEN. Yes they are
numerically equal, but the difference is important, as the switch treats
VLAN-tagged traffic specially and knows to increase the maximum accepted
frame size automatically. So it is always wrong to account for VLAN in
the MAC_MAXLEN_CFG register.
Unconditionally increase the maximum allowed frame size for
double-tagged traffic. Accounting for the additional length does not
mean that the other VLAN membership checks aren't performed, so there's
no harm done.
Also, stop abusing the MTU name for configuring the MRU. There is no
support for configuring the MRU on an interface at the moment.
Fixes: a556c76adc ("net: mscc: Add initial Ocelot switch support")
Fixes: fa914e9c4d ("net: mscc: ocelot: create a helper for changing the port MTU")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e18b353f10 ("ipvlan: add cond_resched_rcu() while
processing muticast backlog") added a cond_resched_rcu() in a loop
using rcu protection to iterate over slaves.
This is breaking rcu rules, so lets instead use cond_resched()
at a point we can reschedule
Fixes: e18b353f10 ("ipvlan: add cond_resched_rcu() while processing muticast backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Rx bound multicast packets are deferred to a workqueue and
macvlan can also suffer from the same attack that was discovered
by Syzbot for IPvlan. This solution is not as effective as in
IPvlan. IPvlan defers all (Tx and Rx) multicast packet processing
to a workqueue while macvlan does this way only for the Rx. This
fix should address the Rx codition to certain extent.
Tx is still suseptible. Tx multicast processing happens when
.ndo_start_xmit is called, hence we cannot add cond_resched().
However, it's not that severe since the user which is generating
/ flooding will be affected the most.
Fixes: 412ca1550c ("macvlan: Move broadcasts into a work queue")
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPvlan in L3 mode discards outbound multicast packets but performs
the check before ensuring the ether-header is set or not. This is
an error that Eric found through code browsing.
Fixes: 2ad7bf3638 (“ipvlan: Initial check-in of the IPVLAN driver.”)
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's a resource, not a parameter, so we can't copy it into the new
channel's TX queues, otherwise aliasing will lead to resource-
management bugs if the channel is subsequently torn down without
being initialised.
Before the Fixes:-tagged commit there was a similar bug with
tsoh_page, but I'm not sure it's worth doing another fix for such
old kernels.
Fixes: e9117e5099 ("sfc: Firmware-Assisted TSO version 2")
Suggested-by: Derek Shute <Derek.Shute@stratus.com>
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse infrastructure that already exists for pf in legacy mode to show/set
Rx network flow classification rules for uplink representors.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
During transition to uplink representors the code responsible for
initializing ethtool steering functionality wasn't added to representor
init rx routine. This causes NULL pointer dereference during configuration
of network flow classification rule with ethtool (only possible to
reproduce with next commit in this series which registers necessary ethtool
callbacks).
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reuse infrastructure that already exists for pf in legacy mode to show/set
Rx flow hash indirection table and RSS hash key for uplink representors.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Uplink representor traffic will be redirected to an empty root ft rather
than directly to a direct tir or ttc table, this root ft will be empty and
will be used as a link for auto-chaining with ttc table or ethtool tables
in downstream patches.
On load, fs core will connect uplink rep root_ft with ttc table. In case
ethtool steering will be used, fs core will auto connect root_ft with
the ethtool bypass tables, which will be connected with the ttc table.
vport_rx_rule[uplink_rep]->root_ft->ethtool->ttc.
For non-uplink representors, for simplicity root_ft will always point at
ttc table, hence the replace vport_rx rule logic is removed.
vport_rx_rule[non_uplink_rep]->root_ft(ttc).
For now ethtool steering support can only be available on uplink rep.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Instead of giving ft tables one of the largest tables available - 4M,
give it a more reasonable size - 64k. Especially since it will
always be created as a miss hook in the following patch.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
The esw_vport_tbl_get() function returns error pointers on error.
Fixes: 96e326878f ("net/mlx5e: Eswitch, Use per vport tables for mirroring")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
According to PRM, forward to flow table along with either packet
reformat or decap is supported only if reformat_and_fwd_to_table
capability is set for the flow table.
Add dependency on the capability and pack all the conditions for "goto
chain" in a single function.
Fix language in error message in case of not supporting forward to a
lower numbered flow table.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Multi-port RoCE mode requires tagging traffic that passes through the
vport.
This matching can cause performance degradation, therefore disable it
and use the legacy matching on vhca_id and source_port when possible.
Fixes: 92ab1eb392 ("net/mlx5: E-Switch, Enable vport metadata matching if firmware supports it")
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Use reverse chirstmas tree inside mlx5e_ethtool_get_link_ksettings.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
When port speed can't be reported based on ext_eth_proto_capability
or eth_proto_capability instead of reporting speed as unknown check
if the port's speed can be inferred based on the data_rate_oper field.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
