The ltdc pinctrl must be in the display controller node and
not in the peripheral node (hdmi bridge).
Signed-off-by: Yannick Fertré <yannick.fertre@st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This change disables the DMA support (RX/TX) on the NXP's fsl_lpuart
driver - the PIO mode is used instead. This change is necessary for better
robustness of BK4's device use cases with many potentially interrupted
short serial transfers.
Without it the driver hangs when some distortion happens on UART lines.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/sound/simple-card.txt
the 'simple-audio-card,dai-link' may be omitted when the card has
only one DAI link, which is the case here.
Get rid of 'simple-audio-card,dai-link' in order to fix the following
build warning with W=1:
arch/arm/boot/dts/imx6q-gw54xx.dts:19.32-31.5: Warning (unit_address_vs_reg): /sound-digital/simple-audio-card,dai-link@0: node has a unit name, but no reg property
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the touch keyboard present on Hydra board. The controller
is connected only using I2C lines. The interrupt line is not
available hence we use the polling mode.
Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The device node name should reflect generic class of a device so rename
the "iram" node to "sram". This will be also in sync with upcoming DT
schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Drop legacy platform data for omaps for v5.5
This series of changes continues dropping legacy platform data for
omaps. With the proper device tree configuration in place in the dts
files for ti-sysc interconnect target module driver, we can drop the
related platform data and legacy ti,hwmods custom property.
Most of the patches in this series drop platform data and custom dts
property one device class and one SoC at time. This way we can easily
revert one patch at a time in case of unexpected issues if the fix is
not trivial.
For am335x musb, we need to first update the device tree to probe with
ti-sysc interconnect target module driver. And then the following
patches drop the legacy platform data.
Note that this series depends on earlier ti-sysc related driver changes
* tag 'omap-for-v5.5/ti-sysc-drop-pdata-v2-signed-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (40 commits)
ARM: OMAP2+: Drop legacy platform data for am335x musb
ARM: dts: Drop pointless status changing for am3 musb
ARM: dts: Probe am335x musb with ti-sysc
ARM: OMAP2+: Drop legacy platform data for musb on omap4
ARM: OMAP2+: Drop legacy platform data for omap4 mcasp
ARM: OMAP2+: Drop legacy platform data for am3 and am4 mcasp
ARM: OMAP2+: Drop legacy platform data for dra7 rng
ARM: OMAP2+: Drop legacy platform data for am3 and am4 rng
ARM: OMAP2+: Drop legacy platform data for omap4 hdq1w
ARM: OMAP2+: Drop legacy platform data for dra7 hdq1w
ARM: OMAP2+: Drop legacy platform data for am4 hdq1w
ARM: OMAP2+: Drop legacy platform data for omap5 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap4 mcbsp
ARM: OMAP2+: Drop legacy platform data for omap5 wdt
ARM: OMAP2+: Drop legacy platform data for dra7 wdt
ARM: OMAP2+: Drop legacy platform data for am3 and am4 wdt
ARM: dts: Drop custom hwmod property for omap5 mmc
ARM: dts: Drop custom hwmod property for am4 mmc
ARM: dts: Drop custom hwmod property for am3 mmc
ARM: dts: Drop custom hwmod property for omap5 i2c
...
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-3
Signed-off-by: Olof Johansson <olof@lixom.net>
Device tree changes for omaps for v5.5
This series of changes adds support for few new boards, moves
remaining ti wilink bluetooth users to use the serdev driver,
and improves support for existing devices:
- Add support for NetCAN Plus devices
- Configure wilink bluetooth for logicpd-torpedo and omap3-igep
- Switch to using generic LCD panel for logicpd-torpedo and
increase camera pixel clock
- Configure droid4 for 300mA USB host mode and move to a common file
to start adding support for droid bionic
- Rename ocmcram node to sram
* tag 'omap-for-v5.5/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: add DTS for NetCom Plus 4xx and 8xx device series
ARM: dts: add DTS for NetCom Plus 1xx and 2xx device series
ARM: dts: add DTS for NetCAN Plus devices
ARM: dts: omap: Rename "ocmcram" node to "sram"
ARM: dts: logicpd-torpedo-37xx-devkit: Increase camera pixel clock
ARM: dts: am: Rename "ocmcram" node to "sram"
ARM: dts: logicpd-torpedo: Disable Bluetooth Serial DMA
ARM: dts: IGEP: Add WiLink UART node
ARM: dts: LogicPD Torpedo: Add WiLink UART node
ARM: dts: logicpd-torpedo-37xx-devkit-28: Reference new DRM panel
ARM: dts: logicpd-torpedo-baseboard: Reduce video regulator chatter
ARM: dts: Add minimal support for Droid Bionic xt875
ARM: dts: omap4-droid4: Allow 300mA current for USB peripherals
ARM: dts: Use level interrupt for omap4 & 5 wlcore
Link: https://lore.kernel.org/r/pull-1571934890-285615@atomide.com-2
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.5, please pull the following:
- Stefan paves the way for supporting the Raspberry Pi 4 and gets rid of
a bunch of dtc checker warnings by removing incorrect
nodes/properties, moving BCM2835/6/7 specific nodes into the
appropriate DTS, converts Raspberry Pi boards to JSON schema, and
finally adds minimal Raspberry Pi 4 model B support
- Dan adds support for the Luxul XWC-2000 router based on the BCM47094 SoC
- Chris adds a proper label to the Hurricane 2 watchdog controller node
* tag 'arm-soc/for-5.5/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm: HR2: add label to sp805 watchdog
ARM: dts: BCM5301X: Add DT for Luxul XWC-2000
arm64: dts: broadcom: Add reference to RPi 4 B
ARM: dts: Add minimal Raspberry Pi 4 support
dt-bindings: arm: bcm2835: Add Raspberry Pi 4 to DT schema
dt-bindings: arm: Convert BCM2835 board/soc bindings to json-schema
ARM: dts: bcm283x: Move BCM2835/6/7 specific to bcm2835-common.dtsi
ARM: dts: bcm283x: Remove brcm,bcm2835-pl011 compatible
ARM: dts: bcm283x: Remove simple-bus from fixed clocks
Link: https://lore.kernel.org/r/20191023212814.30622-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
This DTS file covers all four and eight port NetCom Plus devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This DTS file covers all one and two port NetCom Plus devices.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This DTS file covers both NetCAN Plus 110 and 120 WLAN models.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The device node name should reflect generic class of a device so rename
the children of SysRAM node to "smp-sram". This will be also in sync
with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
A number of fixes for this release, but mostly:
- A fixup for the A10 CSI DT binding merged during the 5.4-rc1 window
- A fix for a dt-binding error
- Addition of phy regulator delays
- The PMU on the A64 was found to be non-functional, so we've dropped it for now
* tag 'sunxi-fixes-for-5.4-1' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Drop the module clock from the device tree
dt-bindings: media: sun4i-csi: Drop the module clock
media: dt-bindings: Fix building error for dt_binding_check
arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delay
arm64: dts: allwinner: a64: Drop PMU node
arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delay
Link: https://lore.kernel.org/r/80085a57-c40f-4bed-a9c3-19858d87564e.lettre@localhost
Signed-off-by: Olof Johansson <olof@lixom.net>
The default is enabled, and there should be no need to reconfigure
the status for SoC internal devices in the board specific files.
Only the USB PHY used needs to be configured in the board specific
files.
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe musb with ti-sysc interconnect driver and dts data
with the following changes:
1. Swap the old ti,am33xx-usb compatible wrapper to generic ti-sysc
driver. This means later on we can also remove the old wrapper driver
drivers/usb/musb/musb_am335x.c
2. Update the child nodes to use the ranges provided by ti-sysc
3. Drop unneeded status = "enabled" tinkering for SoC internal devices.
This allows us to remove some useless board specific boilerplate code
in the following patches
Cc: Bin Liu <b-liu@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This is a Dell Wyse thin client, variously referred to as "Ariel",
"3020" or "Tx0D" where "x" stands for the software it was shipped with.
I somewhat arbitrarily chose "ariel".
There are bits missing, because the drivers are not in and bindings are not
settled yet:
* Things missing from mmp3.dtsi:
HSIC controller and its PHY (only the internal Ethernet is connected
here, the hub with external USB2 ports is connected to the U2O controller
that works well), Vivante GC2000 GPU
* &twsi1/regulator@19
Marvell 88pm867 power regulator
* &twsi3/vga-dvi-encoder@76
Chrontel CH7033B-BF VGA & DVI encoder
* &twsi3/sound-codec@30
Sound chip, probably a Marvell 88ce156
* &twsi4/embedded-controller@58
ENE KB3930QF Embedded Controller, also seems to be connected to &ssp4.
Might not need a driver -- about the only useful thing it can do is to
reboot the machine when tickled via some GPIO lines.
Also there seems to be something at &twsi1 address 0x50.
Link: https://lore.kernel.org/r/20191022152837.3553524-1-lkundrak@v3.sk
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Olof Johansson <olof@lixom.net>
The device node name should reflect generic class of a device so rename
the "ocmcram" node to "sram". This will be also in sync with upcoming DT
schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default settings used on the baseboard are good for the
OMAP3530 and are compatible with the DM3730. However, the
DM3730 has a faster L3 clock which means the camera pixel clock
can also be pushed faster as well.
This patch increase the Pixel clock to 90MHz which is the
maximum the current ISP driver permits for an L3 clock
of 200MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The device node name should reflect generic class of a device so rename
the "ocmcram" node and its children to "sram". This will be also in
sync with upcoming DT schema. No functional change.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The default serial driver for omap2plus is the 8250_omap driver.
Unfortunately, this driver does not yet appear to have fully
functional DMA on OMAP3630/DM3730 which causes some timeouts and
frame errors.
This patch removes the DMA entry from the device tree which allow
the UART to operate without Bluetooth frame errors. If/when DMA
is working on OMAP3630, this should be reverted.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: Marvell MMP Device Tree patches for v5.5
This tag includes binding documentation for various hardware found on Marvell
MMP3 SoC along a DTS file for said hardware.
* tag 'mmp-dt-for-v5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lkundrak/linux-mmp:
ARM: dts: mmp3: Add MMP3 SoC dts file
dt-bindings: phy-mmp3-usb: Add bindings
dt-bindings: mrvl,intc: Add a MMP3 interrupt controller
dt-bindings: arm: mrvl: Document MMP3 compatible string
dt-bindings: arm: Convert Marvell MMP board/soc bindings to json-schema
dt-bindings: arm: cpu: Add Marvell MMP3 SMP enable method
Link: https://lore.kernel.org/r/d4897c4a92319527c46147244282803cd9f5a1ff.camel@v3.sk
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung DTS changes for DMC driver for v5.5
Add bindings and update device tree sources of Exynos5422 platforms with
new Dynamic Memory Controller nodes and properties.
* tag 'samsung-dt-dmc-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: memory-controllers: exynos5422-dmc: Correct example syntax and memory region
ARM: dts: exynos: Add interrupts to DMC controller in Exynos5422
ARM: dts: exynos: Extend mapped region for DMC on Exynos5422
dt-bindings: memory-controllers: exynos5422-dmc: Add interrupt mode
dt-bindings: ddr: Add bindings for Samsung LPDDR3 memories
ARM: dts: exynos: Add DMC device to Exynos5422 and Odroid XU3-family boards
ARM: dts: exynos: Add syscon compatible to clock controller on Exynos542x
dt-bindings: memory-controllers: Add Exynos5422 DMC device description
dt-bindings: ddr: Add bindings for LPDDR3 memories
dt-bindings: ddr: Rename lpddr2 directory
Link: https://lore.kernel.org/r/20191021180453.29455-6-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung DTS ARM changes for v5.5
1. Add ARM architected timers on Exynos5 for KVM-based virtualization,
2. Extend chip identification needed for future Adaptive Supply Voltage,
3. Add audio support to Arndale board,
4. Fix init order of clock providers on s3c64xx,
5. A lot of cleanups and adjustments of DTS with DT schema.
* tag 'samsung-dt-5.5' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: s3c64xx: Fix init order of clock providers
ARM: dts: exynos: Rename SysRAM node to "sram"
ARM: dts: exynos: Rename power domain nodes to "power-domain" in Exynos4
ARM: dts: exynos: Add audio support (WM1811 CODEC boards) to Arndale board
ARM: dts: exynos: Use defines for MCT interrupt GIC SPI/PPI specifier
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos54xx
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos5250
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos4412
ARM: dts: exynos: Remove MCT subnode for interrupt map on Exynos4210
ARM: dts: exynos: Rename Multi Core Timer node to "timer"
ARM: dts: exynos: Split phandle in dmas property
ARM: dts: exynos: Remove obsolete IRQ lines on Exynos3250
ARM: dts: exynos: Add samsung,asv-bin property to Odroid XU3 Lite
ARM: dts: exynos: Add "syscon" compatible string to chipid node on Exynos5
ARM: dts: exynos: Add support ARM architected timers on Exynos5
Link: https://lore.kernel.org/r/20191021180453.29455-4-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
New rk3288 features are Gamma support for the VOPs as well as declaring
the cpuid found in the efuses. Veyron display got a cleanup to use the
interpolated backlight values instead of declaring huge tables
and finally a cleanup fixing some tabs/spaces issues in the dts files.
* tag 'v5.5-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: remove some tabs and spaces from dtsi files
ARM: dts: rockchip: Add RK3288 VOP gamma LUT address
ARM: dts: rockchip: Use interpolated brightness tables for veyron
ARM: dts: rockchip: Add cpu id to rk3288 efuse node
Link: https://lore.kernel.org/r/1770986.Em1ahGqaF7@phil
Signed-off-by: Olof Johansson <olof@lixom.net>
This pull request contains Broadcom ARM-based SoC Device Tree fixes for
5.4, please pull the following:
- Stefan removes the activity LED node from the CM3 DTS since there is
no driver for that LED yet and leds-gpio cannot drive it either
* tag 'arm-soc/for-5.4/devicetree-fixes-part2' of https://github.com/Broadcom/stblinux:
ARM: dts: bcm2837-rpi-cm3: Avoid leds-gpio probing issue
Link: https://lore.kernel.org/r/20191021194302.21024-1-f.fainelli@gmail.com
Signed-off-by: Olof Johansson <olof@lixom.net>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the related platform data and custom ti,hwmods
dts property.
As we're just dropping data, and the early platform data init
is based on the custom ti,hwmods property, we want to drop both
the platform data and ti,hwmods property in a single patch.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We can now probe devices with ti-sysc interconnect driver and dts
data. Let's drop the custom ti,hwmods dts property. We have already
dropped the platform data earlier, but have been still allocating it
dynamically, which is no longer needed.
Cc: Keerthy <j-keerthy@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
