MMIO block with tracked mmio, is introduced for the sake of performance
of searching tracked mmio. All the tracked mmio needs to get the initial
value from the HW state during vGPU being created. This patch is to
initialize the tracked registers in MMIO block with the HW state.
v2: Add "Fixes:" line for this patch (Zhenyu)
Fixes: 65f9f6febf ("drm/i915/gvt: Optimize MMIO register handling for some large MMIO blocks")
Signed-off-by: Tina Zhang <tina.zhang@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
The driver stores lut values from the fbdev interface, and is able
to give them back, but does not appear to do anything with these
lut values. The generic fb helpers have replaced this function,
and may even have made the driver work for the C8 mode from the
fbdev interface. But that is untested.
Since the fb helpers .gamma_set and .gamma_get are obsolete,
remove the dead code.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20170713162538.22788-10-peda@axentia.se
Iommu would get page fault with following path:
vop_disable:
1, disable all windows and set vop config done
2, vop enter to standy, all windows not works, but their registers
are not clean, when you read window's enable bit, may found the
window is enable.
vop_enable:
1, memcpy(vop->regsbak, vop->regs, len)
save current vop registers to vop->regsbak, then you can found
window is enable on regsbak.
2, VOP_WIN_SET(vop, win, gate, 1);
force enable window gate, but gate and enable are on same
hardware register, then window enable bit rewrite to vop hardware.
3, vop power on, and vop might try to scan destroyed buffer,
then iommu get page fault.
Move windows disable after vop regsbak restore, then vop regsbak mechanism
would keep tracing the modify, everything would be safe.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501494582-6934-1-git-send-email-mark.yao@rock-chips.com
Iommu would get page fault with following path:
vop_disable:
1, disable all windows and set vop config done
2, vop enter to standy, all windows not works, but their registers
are not clean, when you read window's enable bit, may found the
window is enable.
vop_enable:
1, memcpy(vop->regsbak, vop->regs, len)
save current vop registers to vop->regsbak, then you can found
window is enable on regsbak.
2, VOP_WIN_SET(vop, win, gate, 1);
force enable window gate, but gate and enable are on same
hardware register, then window enable bit rewrite to vop hardware.
3, vop power on, and vop might try to scan destroyed buffer,
then iommu get page fault.
Move windows disable after vop regsbak restore, then vop regsbak mechanism
would keep tracing the modify, everything would be safe.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Sandy huang <sandy.huang@rock-chips.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1501494582-6934-1-git-send-email-mark.yao@rock-chips.com
Just a few small fixes for 4.13.
* 'drm-fixes-4.13' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: Use list_del_init in amdgpu_mn_unregister
drm/amdgpu: Fix undue fallthroughs in golden registers initialization
drm/amdgpu: fix header on gfx9 clear state
rcar-du updates, contains vsp1 updates as well.
* tag 'drm-next-du-20170803' of git://linuxtv.org/pinchartl/media: (24 commits)
drm: rcar-du: Use new iterator macros
drm: rcar-du: Repair vblank for DRM page flips using the VSP
drm: rcar-du: Fix race condition when disabling planes at CRTC stop
drm: rcar-du: Wait for flip completion instead of vblank in commit tail
drm: rcar-du: Use the VBK interrupt for vblank events
drm: rcar-du: Add HDMI outputs to R8A7796 device description
drm: rcar-du: Remove an unneeded NULL check
drm: rcar-du: Setup planes before enabling CRTC to avoid flicker
drm: rcar-du: Configure DPAD0 routing through last group on Gen3
drm: rcar-du: Restrict DPLL duty cycle workaround to H3 ES1.x
drm: rcar-du: Support multiple sources from the same VSP
drm: rcar-du: Fix comments to comply with the kernel coding style
drm: rcar-du: Use of_graph_get_remote_endpoint()
v4l: vsp1: Add support for header display lists in continuous mode
v4l: vsp1: Add support for multiple DRM pipelines
v4l: vsp1: Add support for multiple LIF instances
v4l: vsp1: Add support for new VSP2-BS, VSP2-DL and VSP2-D instances
v4l: vsp1: Add support for the BRS entity
v4l: vsp1: Add pipe index argument to the VSP-DU API
v4l: vsp1: Don't create links for DRM pipeline
...
This adds a new drm_setup_crtcs_fb() function to handle the parts of
drm_setup_crtcs() that touch fb_helper->fb and fb_helper->fbdev. When
drm_setup_crtcs() is called during initialization, these fields are NULL
because they have not been allocated yet.
There is currently a hack at the end of drm_fb_helper_single_fb_probe()
that sets fb_helper->fb, so it is moved to the new drm_setup_crtcs_fb()
function.
This is also done in preparation for addition setup that requires access
to fb_helper->fbdev.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1501777149-8310-2-git-send-email-david@lechnology.com
The motivation behind this new interface is expose at runtime the
creation of new OA configs which can be used as part of the i915 perf
open interface. This will enable the kernel to learn new configs which
may be experimental, or otherwise not part of the core set currently
available through the i915 perf interface.
v2: Drop DRM_ERROR for userspace errors (Matthew)
Add padding to userspace structure (Matthew)
s/guid/uuid/ (Matthew)
v3: Use u32 instead of int to iterate through registers (Matthew)
v4: Lock access to dynamic config list (Lionel)
v5: by Matthew:
Fix uninitialized error values
Fix incorrect unwiding when opening perf stream
Use kmalloc_array() to store register
Use uuid_is_valid() to valid config uuids
Declare ioctls as write only
Check padding members are set to 0
by Lionel:
Return ENOENT rather than EINVAL when trying to remove non
existing config
v6: by Chris:
Use ref counts for OA configs
Store UUID in drm_i915_perf_oa_config rather then using pointer
Shuffle fields of drm_i915_perf_oa_config to avoid padding
v7: by Chris
Rename uapi pointers fields to end with '_ptr'
v8: by Andrzej, Marek, Sebastian
Update register whitelisting
by Lionel
Add more register names for documentation
Allow configuration programming in non-paranoid mode
Add support for value filter for a couple of registers already
programmed in other part of the kernel
v9: Documentation fix (Lionel)
Allow writing WAIT_FOR_RC6_EXIT only on Gen8+ (Andrzej)
v10: Perform read access_ok() on register pointers (Lionel)
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: Andrzej Datczuk <andrzej.datczuk@intel.com>
Reviewed-by: Andrzej Datczuk <andrzej.datczuk@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170803165812.2373-2-lionel.g.landwerlin@intel.com
In the following commit we'll introduce loadable userspace
configs. This change reworks how configurations are handled in the
perf driver and retains only the test configurations in kernel space.
We now store the test config in dev_priv and resolve the id only once
when opening the perf stream. The OA config is then handled through a
pointer to the structure holding the configuration details.
v2: Rework how test configs are handled (Lionel)
v3: Use u32 to hold number of register (Matthew)
v4: Removed unused dev_priv->perf.oa.current_config variable (Matthew)
v5: Lock device when accessing exclusive_stream (Lionel)
v6: Ensure OACTXCONTROL is always reprogrammed (Lionel)
v7: Switch a couple of index variable from int to u32 (Matthew)
Signed-off-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20170803165812.2373-3-lionel.g.landwerlin@intel.com
for_each_obj_in_state is about to be removed, so use the correct new
iterator macros.
Also look at new_plane_state instead of plane->state when looking up
the hw planes in use. They should be the same except when reallocating,
(in which case this code is skipped) and we should really stop looking
at obj->state whenever possible.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The driver recently switched from handling page flip completion in the
DU vertical blanking handler to the VSP frame end handler to fix a race
condition. This unfortunately resulted in incorrect timestamps in the
vertical blanking events sent to userspace as vertical blanking is now
handled after sending the event.
To fix this we must reverse the order of the two operations. The easiest
way is to handle vertical blanking in the VSP frame end handler before
sending the event. The VSP frame end interrupt occurs approximately 50µs
earlier than the DU frame end interrupt, but this should not cause any
undue harm.
As we need to handle vertical blanking even when page flip completion is
delayed, the VSP driver now needs to call the frame end completion
callback unconditionally, with a new argument to report whether page
flip has completed.
With this new scheme the DU vertical blanking interrupt isn't needed
anymore, so we can stop enabling it.
Fixes: d503a43ac0 ("drm: rcar-du: Register a completion callback with VSP1")
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
When stopping the CRTC the driver must disable all planes and wait for
the change to take effect at the next vblank. Merely calling
drm_crtc_wait_one_vblank() is not enough, as the function doesn't
include any mechanism to handle the race with vblank interrupts.
Replace the drm_crtc_wait_one_vblank() call with a manual mechanism that
handles the vblank interrupt race.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Page flips can take more than one vertical blanking to complete if
arming the page flips races with the vertical blanking interrupt.
Waiting for one vblank to complete the atomic commit in the commit tail
handler is thus incorrect, and can lead to framebuffers being released
while still being scanned out.
Fix this by waiting for flip completion instead, using the
drm_atomic_helper_wait_for_flip_done() helper.
Fixes: 0d230422d256 ("drm: rcar-du: Register a completion callback with VSP1")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
When implementing support for interlaced modes, the driver switched from
reporting vblank events on the vertical blanking (VBK) interrupt to the
frame end interrupt (FRM). This incorrectly divided the reported refresh
rate by two. Fix it by moving back to the VBK interrupt.
Fixes: 906eff7fca ("drm: rcar-du: Implement support for interlaced modes")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Commit 52055bafa1 ("drm: rcar-du: Move plane commit code from CRTC
start to CRTC resume") changed the order of the plane commit and CRTC
enable operations to accommodate the runtime PM requirements. However,
this introduced corruption in the first displayed frame, as the CRTC is
now enabled without any plane configured. On Gen2 hardware the first
frame will be black and likely unnoticed, but on Gen3 hardware we end up
starting the display before the VSP compositor, which is more
noticeable.
To fix this, revert the order of the commit operations back, and handle
runtime PM requirements in the CRTC .atomic_begin() and .atomic_enable()
helper operation handlers.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
On Gen3 SoCs DPAD0 routing is configured through the last CRTC group,
unlike on Gen2 where it is configured through the first CRTC group. Fix
the driver accordingly.
Fixes: 2427b30377 ("drm: rcar-du: Add R8A7795 device support")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
The H3 ES1.x exhibits dot clock duty cycle stability issues. We can work
around them by configuring the DPLL to twice the desired frequency,
coupled with a /2 post-divider. This isn't needed on other SoCs and
breaks HDMI output on M3-W for a currently unknown reason, so restrict
the workaround to H3 ES1.x.
From an implementation point of view, move work around handling outside
of the rcar_du_dpll_divider() function by requesting a x2 DPLL output
frequency explicitly. The existing post-divider calculation mechanism
will then take care of dividing the clock by two automatically.
While at it, print a more useful debugging message to ease debugging
clock rate issues.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
