As it is quite common to use a stereo pair of amps but share the IRQ
line between them both add the IRQF_SHARED flag whilst requesting
cs35l35's IRQ.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for setting how the I2S pins are driven in unused slots,
currently the chip will just use the default of drive 0, however this
causes issues when multiple devices are attached to the same bus.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
A return statement is missing just before the error paths at the end of
probe. This causes us to fall straight into the error path and disable
the supplies and re-enable reset, as these are only controlled during
probe this causes the part to no longer function.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use manual mode for jack detection function to increase accuracy.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TDM is necessary for more than 2 channels. And there is no control bit
to specify which slots are using. Machine driver will not need to call
snd_soc_dai_set_tdm_slot if we do it in rt5665_hw_params.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Vref3 is necessary for Mono Amp. So add it to dapm routes
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the "cansleep" variant of gpiod_set_value so the driver can be used
with slow gpio controllers as well.
Fixes: 85825d5e88 ("ASoC: dio2125: add dio2125 amp driver")
Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dio2125 is a stereo output driver with adjustable gain.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for the Cirrus Logic
CS35L35 9V Boosted Amplifier
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should not be writing acknowledge controls until the firmware is
running, as in the case of preloaded firmwares the DSP memory may be
unaccessible to whilst in the preloaded state. This means a write to the
control during this time could be lost.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Volatile controls should only be accessed when the firmware is active,
currently however writes to these controls will succeed, but the data
will be lost, if the firmware is powered down. Update this behaviour such
that an error is returned the same as it is for reads.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The es7134 is 24bit, 192Khz i2s DA converter for PCM audio.
Datasheet is available here : http://www.everest-semi.com/pdf/ES7134LV%20DS.pdf
This driver is also compatible with the es7144, which is the same as the
es7134, with 2 additional pins for filtering capacitors.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix not to update the iterator element, instead use list_del to remove
entry from the list.
This fixes the following coccinelle and static checker warning:
sound/soc/codecs/hdac_hdmi.c:1884:2-21:iterator with update on line
1885
sound/soc/codecs/hdac_hdmi.c:2011 hdac_hdmi_dev_remove()
error: potential NULL dereference 'port'.
Fixes: e0e5d3e5a53b('ASoC: hdac_hdmi: Add support for multiple ports to a PCM')
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using pin list array iterator outside the iteration of the list can
point to dummy element, which can be invalid. So don't use pin variable
outside the pin list iteration.
This fixes the following coccinelle warning:
sound/soc/codecs/hdac_hdmi.c:1419:5-8: ERROR: invalid reference to the
index variable of the iterator
Fixes: 2acd8309a3a4('ASoC: hdac_hdmi: Add support to handle MST capable pin')
Reported-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Without this I am getting the following messages at boot on my Trimslice:
tlv320aic23-codec 2-001a: Control not supported for path LLINEIN -> [NULL] -> Line Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for LLINEIN --> NULL --> Line Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route LLINEIN -> NULL -> Line Input
tlv320aic23-codec 2-001a: Control not supported for path RLINEIN -> [NULL] -> Line Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for RLINEIN --> NULL --> Line Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route RLINEIN -> NULL -> Line Input
tlv320aic23-codec 2-001a: Control not supported for path MICIN -> [NULL] -> Mic Input
tlv320aic23-codec 2-001a: ASoC: no dapm match for MICIN --> NULL --> Mic Input
tlv320aic23-codec 2-001a: ASoC: Failed to add route MICIN -> NULL -> Mic Input
tegra-snd-trimslice sound: tlv320aic23-hifi <-> 70002800.i2s mapping ok
Signed-off-by: Liviu Dudau <liviu@dudau.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The master and slave modes don't share the same table for MCLK/LRCLK
ratios. The slaves mode has bigger ratios that allow to use BCLK that
matche sampling frequency of 192khz.
This commit enables this rate only for slave mode, i.e it does not
declare this frequency in sysclk_contraints, resulting to an error in
master mode (not supported CLK).
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently most of the standard rates are supported by this driver.
Instead of defining each supported rate one by one, we use the SND macro
SNDRV_PCM_RATE_8000_48000. Also adds support for 88.2khz as the codec
supports it and the sys clocks are already supported.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In master mode, SCLK and LRCLK signals are generated by the CODEC when
any of the ADC/DAC are enabled. SCLK is derived from MCLK via a
programmable division set by BLK_DIV, LRCLK is derived from MCLK via
another programmable division set by ADCFsRatio/DACFsRatio.
In slave mode, SCLK and LRCLK signals are received as inputs and
supplied externally. LRCLK and SCLK must be synchronously derived from
MCLK with specific rates. The device can auto detect MCLK/LRCLK ratio
according to a predefined table. LRCLK/SCLK ratio is usually 64 (SCLK =
64 * LRCLK)
This commits adds support to let to device auto detect and decide which
ratio to use. The mclkdiv2 and BCLK_DIV ratio and put to zero.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
configurable LRC and BCLK divide. The driver
will make configurations of LRC and BCLK automatically according to
BCLK and FS information in master mode.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Geminilake reference platform also uses combo jack for audio connector
so we need to set codec pdata to use this based on DMI match for this
board.
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Represent each port as machine DAPM pin widget. This helps in
enable/disable pin when monitor is connected/disconnected in case pcm
is rendered to multiple ports.
Create machine pin widgets and pin switch kcontrol for each port and
report based on the pin status
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use snd_soc_jack instead of snd_jack and create the jack in machine
driver and pass the jack pointer to hdac_hdmi driver for jack
reporting.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since we have the MST feature enabled and Pin-Port mux for user to
select the converter routing, multiple port mapping to same converter
needs to be supported.
To support multiple port mapped to same converter following changes are
done for this:.
o Add port list to pcm, so that multiple ports can be mapped to a PCM.
o Jack reporting in case where multiple port are attached to same PCM.
o Change hdac_hdmi_get_port_from_cvt(), channel_map, remove functions
to parse through all ports mapped to same the PCM.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To enable stream on a specific port of a MST capable pin, the port
needs to be selected before we configure the pin widget verb.
When port is selected, all the pin widget verb controlling the sink
device operation will be directed to selected port. So add port
selection before configuring the pin widget verb.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ELD notification can be received asynchronously from the graphics
side and this may happen just at the moment the sound driver is
initializing and notification will be missed. Similarly at system
resume, the notification is ignored as the ELD and connection states
are updated in anyway at the end of the resume.
So check the jack status in boot/resume by querying the port presence
based on pin caps and report the jack status.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support DP MST audio, new pin verbs/params are added. This patch
adds helper functions to do following:
o To set a specific port
o To get the currently selected port
o To get the length of port.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While unregistering the hdmi-codec, the hdmi device list must be
cleaned up. It avoid kernel page fault when registering again the
hdmi-codec.
Signed-off-by: Vincent Abriou <vincent.abriou@st.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
To handle jack event and configuration of the pin widget for MST
capable pin, this patch adds:
o Flag to identify the pin is MST capable.
o In notify callback(), based on the pipe and port information marks if
the port is mst_capable. In case of non MST, port is defaulted to zero.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With MST each pin contains several ports to which device can be
connected.
As a preparatory work to support DP MST this patch adds below changes:
1. Defines the port structure and moves all stream related information
like ELD, converter list, chmap to port.
2. Creates ports for each pin based on the max_ports support.
3. Based on Pin-Port combination creates DAPM Mux widget instead of Pin
to allow user to select a converter.
4. Port zero is the default port when pin does not support MST.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The two front-ends to the codec can now be selected individually, but fail to
build when the bus support is missing:
sound/built-in.o: In function `es8328_spi_probe':
es8328-spi.c:(.text+0x125854): undefined reference to `__devm_regmap_init_spi'
sound/built-in.o: In function `es8328_spi_driver_init':
es8328-spi.c:(.init.text+0x3589): undefined reference to `__spi_register_driver'
Related to this, the added dependency on SND_SOC_ES8328 breaks:
warning: (SND_SOC_ALL_CODECS) selects SND_SOC_ES8328_I2C which has unmet direct dependencies (SOUND && !M68K && !UML && SND && SND_SOC && SND_SOC_ES8328 && I2C)
This adds the respective Kconfig dependencies and changes SND_SOC_ES8328 to a hidden
symbol that is selected implicitly by the two more specific options, as we do for
some other codecs. We have to remove the 'depends on' for SND_SOC_IMX_ES8328 in the
same step to avoid a recursive dependency.
Fixes: aa00f2c8af ("ASoC: Allow to select ES8328_I2C and ES8328_SPI directly")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, we have to select these symbols explictly via Kconfig, from
another entry. If we plan to use generic audio drivers like
simple-audio-card, the user need to be able to enable these symbols
directly via the menuconfig.
This commit also fixes unmet dependencies to SND_SOC_IMX_ES8328 caused
by these changes.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
