This is an important part of the DDI initalization as well as
for changing the voltage during DisplayPort link training.
This new sequence for Cannonlake is more like Broxton style
but still with different registers, different table and
different steps.
v2: Do not write to DW4_GRP to avoid overwrite individual loadgen.
Fix PORT_CL_DW5 SUS Clock Config set.
v3: As previous platforms use only eDP table if low voltage was
requested.
v4: fix Werror:maybe uninitialized (Paulo)
v5: Rebase on top of dw2_swing_sel changes
on previous patches.
v6: Using flexible SCALING_MODE_SEL(x).
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-11-git-send-email-rodrigo.vivi@intel.com
These tables are used on voltage wswing sequence initialization
on Cannonlake.
It is a complete new format now in use by the voltage swing team,
not following any other standard in use by any other platform.
Also the registers are different as well. So let's redefine
the translation table for Cannonlake.
The table is huge. So we minimized with the fields that are
different or might be different anytime soon. The common
values will be hardcoded on the voltage swing sequence.
v2: Merge the lower and the upper bits to match the spec table
and make review easier. This was possible with the good
idea for Manasi with a better way to handle it on the bit
macro definition presented on previous patch.
Credits-to: Manasi
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1497047175-27250-10-git-send-email-rodrigo.vivi@intel.com
Atm disabling either DP or eDP outputs can generate a spurious short
pulse interrupt. The reason is that after disabling the port the source
will stop sending a valid stream data, while the sink expects either a
valid stream or the idle pattern. Since neither of this is sent the sink
assumes (after an arbitrary delay) that the link is lost and requests
for link retraining with a short pulse.
The spurious pulse is a real problem at least for eDP panels with long
power-off / power-cycle delays: as part of disabling the output we
disable the panel power. The subsequent spurious short pulse handling
will have to turn the power back on, which means the driver has to do a
redundant wait for the power-off and power-cycle delays. During system
suspend this leads to an unnecessary delay up to ~1s on systems with
such panels as reported by Rui.
To fix this put the sink to DPMS D3 state before turning off the port.
According to the DP spec in this state the sink should not request
retraining. This is also what we do already on pre-ddi platforms.
As an alternative I also tried configuring the port to send idle pattern
- which is against BSPec - and leave the port in normal mode before
turning off the port. Neither of these resolved the problem.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-and-tested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496250335-7627-1-git-send-email-imre.deak@intel.com
Geminilake platform sports a native HDMI 2.0 controller, and is
capable of driving pixel-clocks upto 594Mhz. HDMI 2.0 spec
mendates scrambling for these higher clocks, for reduced RF footprint.
This patch checks if the monitor supports scrambling, and if required,
enables it during the modeset.
V2: Addressed review comments from Ville:
- Do not track scrambling status in DRM layer, track somewhere in
driver like in intel_crtc_state.
- Don't talk to monitor at such a low layer, set monitor scrambling
in intel_enable_ddi() before enabling the port.
V3: Addressed review comments from Jani
- In comments, function names, use "sink" instead of "monitor",
so that the implementation could be close to the language of
HDMI spec.
V4: Addressed review comment from Maarten
- scrambling -> hdmi_scrambling
- high_tmds_clock_ratio -> hdmi_high_tmds_clock_ratio
V5: Addressed review comments from Ville and Ander
- Do not modifiy the crtc_state after compute_config. Move all
scrambling and tmds_clock_ratio calcutations to compute_config.
- While setting scrambling for source/sink, do not check the
conditions again, just go by the crtc_state flags. This will
simplyfy the condition checks.
V6: Addressed review comments from Ville
- Do not add IS_GLK check in disable/enable function, instead add it
in compute_config, while setting state flags.
- Remove unnecessary paranthesis.
- Simplyfy handle_sink_scrambling function as suggested.
- Add readout code for scrambling status in get_ddi_config and add a
check for the same in pipe_config_compare.
V7: Addressed review comments from Ander/Ville
- No separate function for source scrambling, make it inline
- Align the last line of the macro TRANS_DDI_HDMI_SCRAMBLING_MASK
- Do not add platform check while setting source scrambling
- Use pipe_config instead of crtc->config to set sink scrambling
- To readout scrambling status, Compare with SCRAMBLING_MASK
not any of its bits
- Remove platform check in intel_pipe_config_compare while checking
scrambling status
V8: Fixed mege conflict, Addressed review comments from Ander
- Remove the desciption/comment about scrambling fom the caller, move
it to the function
- Move the IS_GLK check into scrambling function
- Fix alignment
V9: Fixed review comments from Ville, Ander
- Pass the scrambling state variables as bool input to the sink_scrambling
function and let the disable call be unconditional.
- Fix alignments in function calls and debug messages.
- Add kernel doc for function intel_hdmi_handle_sink_scrambling
V10: Rebase
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1489404244-16608-6-git-send-email-shashank.sharma@intel.com
According to bspec, the DDI IO power domains should be enabled after
enabling the DPLL and mapping it to the DDI. The current order doesn't
seem to create problems with Skylake and Kabylake, but causes enable
timeouts in Geminilake.
v2: Rebase.
- Take power domain references before sanitizing encoders. (Imre)
- Add comment to get_encoder_power_domains() defition. (Ander)
v3: Don't put the domain if called with HSW/BDW's analog encoder. (CI)
v4: Put IO power domain before unmapping DPLL. (Imre)
- Change return type of intel_ddi_get_power_domains() to u64. (Imre)
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com> # v1
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170224141959.5955-1-ander.conselvan.de.oliveira@intel.com
Rather than sprinkling ideas of how big the DDI buf translation tables
are somewhere in intel_dp.c, let's concentrate it all in intel_ddi.c
where the actual tables are defined. To that end we introduce
intel_ddi_dp_voltage_max() which will actually look at the proper
translation table to determine what is the maximum voltage swing level
supported.
v2: Mask out the preemphasis bits from the return value of
intel_ddi_dp_voltage_max()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: David Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170223174901.26749-1-ville.syrjala@linux.intel.com
Along with GLK it was introduced the .is_lp and IS_GEN9_LP.
So, following the same simplification standard we can
put Skylake and Kabylake under the same bucket for most
of the things.
So let's add the IS_GEN9_BC for "Big Core" (non Atom based
platforms).
The i915_drv.c was let out of this patch on purpose
because that is really a decision per platform, just like
other cases where IS_KABYLAKE is different from IS_SKYLAKE.
v2: fix conflict with IS_LP and 3 new cases for this
big core bucket:
- intel_ddi.c: intel_ddi_get_link_dpll
- intel_fbc.c: find_compression_threshold
- i915_gem_gtt.c: gtt_write_workarounds
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1485196357-30599-2-git-send-email-rodrigo.vivi@intel.com
Geminilake is mostly backwards compatible with broxton, so change most
of the IS_BROXTON() checks to IS_GEN9_LP(). Differences between the
platforms will be implemented in follow-up patches.
v2: Don't reuse broxton's path in intel_update_max_cdclk().
Don't set plane count as in broxton.
v3: Rebase
v4: Include the check intel_bios_is_port_hpd_inverted().
Commit message.
v5: Leave i915_dmc_info() out; glk's csr version != bxt's. (Rodrigo)
v6: Rebase.
v7: Convert a few mode IS_BROXTON() occurances in pps, ddi, dsi and pll
code. (Rodrigo)
v8: Squash a couple of DDI patches with more conversions. (Rodrigo)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480667037-11215-2-git-send-email-ander.conselvan.de.oliveira@intel.com
A bunch of source files with just a few instances of the
incorrect INTEL_INFO use.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Add the PLL selection code for HSW/BDW/BXT/SKL into a stand-alone function
in order to allow for the implementation of a platform neutral upfront
link training function.
v4:
* Removed dereferencing NULL pointer in case of failure (Dhinakaran Pandiyan)
v3:
* Add Hooks for all DDI platforms into this standalone function
v2:
* Change the macro to use dev_priv instead of dev (David Weinehall)
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
