We need to tell the driver what the timers frequency is and that the core
has not be configured by the bootrom. Not doing so makes the unit not
boot.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Pull ARM updates from Russell King:
"Lots of little things this time:
- allow modules to be autoloaded according to the HWCAP feature bits
(used primarily for crypto modules)
- split module core and init PLT sections, since the core code and
init code could be placed far apart, and the PLT sections need to
be local to the code block.
- three patches from Chris Brandt to allow Cortex-A9 L2 cache
optimisations to be disabled where a SoC didn't wire up the out of
band signals.
- NoMMU compliance fixes, avoiding corruption of vector table which
is not being used at this point, and avoiding possible register
state corruption when switching mode.
- fixmap memory attribute compliance update.
- remove unnecessary locking from update_sections_early()
- ftrace fix for DEBUG_RODATA with !FRAME_POINTER"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 8672/1: mm: remove tasklist locking from update_sections_early()
ARM: 8671/1: V7M: Preserve registers across switch from Thread to Handler mode
ARM: 8670/1: V7M: Do not corrupt vector table around v7m_invalidate_l1 call
ARM: 8668/1: ftrace: Fix dynamic ftrace with DEBUG_RODATA and !FRAME_POINTER
ARM: 8667/3: Fix memory attribute inconsistencies when using fixmap
ARM: 8663/1: wire up HWCAP/HWCAP2 feature bits to the CPU modalias
ARM: 8666/1: mm: dump: Add domain to output
ARM: 8662/1: module: split core and init PLT sections
ARM: 8661/1: dts: r7s72100: add l2 cache
ARM: 8660/1: shmobile: r7s72100: Enable L2 cache
ARM: 8659/1: l2c: allow CA9 optimizations to be disabled
Pull media updates from Mauro Carvalho Chehab:
"Media updates for v4.12-rc1:
- new driver to support mediatek jpeg in hardware codec
- rc-lirc, s5p-cec and st-cec staging drivers got promoted
- hardware histogram support for vsp1 driver
- added Virtual Media Controller driver, to make easier to test the
media controller
- added a new CEC driver (rainshadow-cec)
- removed two staging LIRC drivers for obscure hardware that are too
obsolete
- added support for Intel SR300 Depth camera
- some improvements at CEC and RC core
- lots of driver cleanups, improvements all over the tree
With this series, we're finally getting rid of the LIRC staging
driver. There's just one left (lirc_zilog), with require more care,
as part of its functionality (IR RX) is already provided by another
driver. Work in progress to convert it on the proper way"
* tag 'media/v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (304 commits)
[media] ov2640: print error if devm_*_optional*() fails
[media] atmel-isc: Fix the static checker warning
[media] ov2640: add support for MEDIA_BUS_FMT_YVYU8_2X8 and MEDIA_BUS_FMT_VYUY8_2X8
[media] ov2640: fix vflip control
[media] ov2640: fix duplicate width+height returning from ov2640_select_win()
[media] ov2640: add missing write to size change preamble
[media] ov2640: add information about DSP register 0xc7
[media] ov2640: improve banding filter register definitions/documentation
[media] ov2640: fix init sequence alignment
[media] ov2640: make GPIOLIB an optional dependency
[media] xc5000: fix spelling mistake: "calibration"
[media] vidioc-queryctrl.rst: fix menu/int menu references
[media] media-entity: only call dev_dbg_obj if mdev is not NULL
[media] pixfmt-meta-vsp1-hgo.rst: remove spurious '-'
[media] mtk-vcodec: avoid warnings because of empty macros
[media] coda: bump maximum number of internal framebuffers to 17
[media] media: mtk-vcodec: remove informative log
[media] subdev-formats.rst: remove spurious '-'
[media] dw2102: limit messages to buffer size
[media] ttusb2: limit messages to buffer size
...
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.12 cycle.
The extra week before the merge window actually resulted in some of
the type of fixes that usually arrive after the merge window already
starting to trickle in from eager developers using -next, I'm
impressed.
I have recruited a Samsung subsubsystem maintainer (Krzysztof) to deal
with the onset of Samsung patches. It works great.
Apart from that it is a boring round, just incremental updates and
fixes all over the place, no serious core changes or anything exciting
like that. The most pleasing to see is Julia Cartwrights work to audit
the irqchip-providing drivers for realtime locking compliance. It's
one of those "I should really get around to looking into that" things
that have been on my TODO list since forever.
Summary:
Core changes:
- add bi-directional and output-enable pin configurations to the
generic bindings and generic pin controlling core.
New drivers or subdrivers:
- Armada 37xx SoC pin controller and GPIO support.
- Axis ARTPEC-6 SoC pin controller support.
- AllWinner A64 R_PIO controller support, and opening up the
AllWinner sunxi driver for ARM64 use.
- Rockchip RK3328 support.
- Renesas R-Car H3 ES2.0 support.
- STM32F469 support in the STM32 driver.
- Aspeed G4 and G5 pin controller support.
Improvements:
- a whole slew of realtime improvements to drivers implementing
irqchips: BCM, AMD, SiRF, sunxi, rockchip.
- switch meson driver to get the GPIO ranges from the device tree.
- input schmitt trigger support on the Rockchip driver.
- enable the sunxi (AllWinner) driver to also be used on ARM64
silicon.
- name the Qualcomm QDF2xxx GPIO lines.
- support GMMR GPIO regions on the Intel Cherryview. This fixes a
serialization problem on these platforms.
- pad retention support for the Samsung Exynos 5433.
- handle suspend-to-ram in the AT91-pio4 driver.
- pin configuration support in the Aspeed driver.
Cleanups:
- the final name of Rockchip RK1108 was RV1108 so rename the driver
and variables to stay consistent"
* tag 'pinctrl-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl: mediatek: Add missing pinctrl bindings for mt7623
pinctrl: artpec6: Fix return value check in artpec6_pmx_probe()
pinctrl: artpec6: Remove .owner field for driver
pinctrl: tegra: xusb: Silence sparse warnings
ARM: at91/at91-pinctrl documentation: fix spelling mistake: "contoller" -> "controller"
pinctrl: make artpec6 explicitly non-modular
pinctrl: aspeed: g5: Add pinconf support
pinctrl: aspeed: g4: Add pinconf support
pinctrl: aspeed: Add core pinconf support
pinctrl: aspeed: Document pinconf in devicetree bindings
pinctrl: Add st,stm32f469-pinctrl compatible to stm32-pinctrl
pinctrl: stm32: Add STM32F469 MCU support
Documentation: dt: Remove ngpios from stm32-pinctrl binding
pinctrl: stm32: replace device_initcall() with arch_initcall()
pinctrl: stm32: add possibility to use gpio-ranges to declare bank range
pinctrl: armada-37xx: Add gpio support
pinctrl: armada-37xx: Add pin controller support for Armada 37xx
pinctrl: dt-bindings: Add documentation for Armada 37xx pin controllers
pinctrl: core: Make pinctrl_init_controller() static
pinctrl: generic: Add bi-directional and output-enable
...
Pull networking updates from David Millar:
"Here are some highlights from the 2065 networking commits that
happened this development cycle:
1) XDP support for IXGBE (John Fastabend) and thunderx (Sunil Kowuri)
2) Add a generic XDP driver, so that anyone can test XDP even if they
lack a networking device whose driver has explicit XDP support
(me).
3) Sparc64 now has an eBPF JIT too (me)
4) Add a BPF program testing framework via BPF_PROG_TEST_RUN (Alexei
Starovoitov)
5) Make netfitler network namespace teardown less expensive (Florian
Westphal)
6) Add symmetric hashing support to nft_hash (Laura Garcia Liebana)
7) Implement NAPI and GRO in netvsc driver (Stephen Hemminger)
8) Support TC flower offload statistics in mlxsw (Arkadi Sharshevsky)
9) Multiqueue support in stmmac driver (Joao Pinto)
10) Remove TCP timewait recycling, it never really could possibly work
well in the real world and timestamp randomization really zaps any
hint of usability this feature had (Soheil Hassas Yeganeh)
11) Support level3 vs level4 ECMP route hashing in ipv4 (Nikolay
Aleksandrov)
12) Add socket busy poll support to epoll (Sridhar Samudrala)
13) Netlink extended ACK support (Johannes Berg, Pablo Neira Ayuso,
and several others)
14) IPSEC hw offload infrastructure (Steffen Klassert)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2065 commits)
tipc: refactor function tipc_sk_recv_stream()
tipc: refactor function tipc_sk_recvmsg()
net: thunderx: Optimize page recycling for XDP
net: thunderx: Support for XDP header adjustment
net: thunderx: Add support for XDP_TX
net: thunderx: Add support for XDP_DROP
net: thunderx: Add basic XDP support
net: thunderx: Cleanup receive buffer allocation
net: thunderx: Optimize CQE_TX handling
net: thunderx: Optimize RBDR descriptor handling
net: thunderx: Support for page recycling
ipx: call ipxitf_put() in ioctl error path
net: sched: add helpers to handle extended actions
qed*: Fix issues in the ptp filter config implementation.
qede: Fix concurrency issue in PTP Tx path processing.
stmmac: Add support for SIMATIC IOT2000 platform
net: hns: fix ethtool_get_strings overflow in hns driver
tcp: fix wraparound issue in tcp_lp
bpf, arm64: fix jit branch offset related to ldimm64
bpf, arm64: implement jiting of BPF_XADD
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.12:
API:
- Add batch registration for acomp/scomp
- Change acomp testing to non-unique compressed result
- Extend algorithm name limit to 128 bytes
- Require setkey before accept(2) in algif_aead
Algorithms:
- Add support for deflate rfc1950 (zlib)
Drivers:
- Add accelerated crct10dif for powerpc
- Add crc32 in stm32
- Add sha384/sha512 in ccp
- Add 3des/gcm(aes) for v5 devices in ccp
- Add Queue Interface (QI) backend support in caam
- Add new Exynos RNG driver
- Add ThunderX ZIP driver
- Add driver for hardware random generator on MT7623 SoC"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (101 commits)
crypto: stm32 - Fix OF module alias information
crypto: algif_aead - Require setkey before accept(2)
crypto: scomp - add support for deflate rfc1950 (zlib)
crypto: scomp - allow registration of multiple scomps
crypto: ccp - Change ISR handler method for a v5 CCP
crypto: ccp - Change ISR handler method for a v3 CCP
crypto: crypto4xx - rename ce_ring_contol to ce_ring_control
crypto: testmgr - Allow ecb(cipher_null) in FIPS mode
Revert "crypto: arm64/sha - Add constant operand modifier to ASM_EXPORT"
crypto: ccp - Disable interrupts early on unload
crypto: ccp - Use only the relevant interrupt bits
hwrng: mtk - Add driver for hardware random generator on MT7623 SoC
dt-bindings: hwrng: Add Mediatek hardware random generator bindings
crypto: crct10dif-vpmsum - Fix missing preempt_disable()
crypto: testmgr - replace compression known answer test
crypto: acomp - allow registration of multiple acomps
hwrng: n2 - Use devm_kcalloc() in n2rng_probe()
crypto: chcr - Fix error handling related to 'chcr_alloc_shash'
padata: get_next is never NULL
crypto: exynos - Add new Exynos RNG driver
...
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
Pull "Fix DTC warnings in Exynos ARMv7 Device Tree sources." from Krzysztof Kozłowski:
* tag 'samsung-dt-4.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Use - instead of @ for DT OPP entries
Pull "ARMv7 VExpress DT fix for v4.12" from Sudeep Holla:
A single fix to remove device tree warnings introduced with recently
added checks in DTC
* tag 'vexpress-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: fix few unit address format warnings
Compiling the DT file with W=1, DTC warns like follows:
Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property
Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
[k.kozlowski: Split patch per ARM and ARM64]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
A function in kernel/bpf/syscall.c which got a bug fix in 'net'
was moved to kernel/bpf/verifier.c in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SPEAr600 has a built-in ADC, which already has a Device Tree binding
described in
Documentation/devicetree/bindings/staging/iio/adc/spear-adc.txt. This
commit adds the description in the SPEAr600 Device Tree of this ADC
device.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The spear6xx doesn't have a pinctrl driver, since the pinmux is globally
defined through a single register, generally configured by the
firmware/bootloader.
Therefore, the pinctrl related properties in spear600-evb.dts are not
necessary.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This commit moves spear600-evb.dts to use the new flash partition Device
Tree binding documented in
Documentation/devicetree/bindings/mtd/partition.txt.
As this Device Tree binding document says: "For backwards compatibility
partitions as direct subnodes of the mtd device are supported. This use
is discouraged."
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Alpine DT changes for 4.12
A bunch of clean up for Alpine device trees, nothing fancy.
* tag 'alpine-dt-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/atenart/linux:
ARM: dts: alpine: add valid clock-frequency values
ARM: dts: alpine: add spaces before the uart node units.
ARM: dts: alpine: remove 0x's from the uart1 node unit address
ARM: dts: alpine: fix PCIe node name
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu dt for 4.12 (part 3)
Use label for USB and SATA nodes on Armada 38x
* tag 'mvebu-dt-4.12-3' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: label USB and SATA nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Aspeed devicetree updates for 4.12
Updates to the device tree to include upstreamed drivers:
- SPI flash controller
- Watchdog
- ADC
In addition we describe some of the clocks so that upstream kernels can
boot on hardware.
* tag 'aspeed-4.12-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
arm: dts: aspeed: Describe ADCs for AST2400/AST2500
ARM: dts: aspeed: romulus: Add UART1
ARM: dts: aspeed: Update watchdog compatible strings
ARM: dts: aspeed: Add a fastread property
ARM: dts: aspeed: Add SPI controller bindings to Romulus
ARM: dts: aspeed: Make G4 clocks fixed
ARM: dts: aspeed: Make G5 clocks fixed
ARM: dts: aspeed: add SPI controller bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Second set of devicetree changes for omaps for v4.12 merge window
to configure various devices:
- Enable DCAN on am57xx-idk
- Enable CPSW ethernet0 and 1 on am335x-icev2
- Non-critical fix for droid 4 PMIC interrupt triggering
- Stop disabling SRAM and GPMC on droid 4
- Configure CPCAP PMIC related devices on droid 4 for ADC, charger
and USB PHY. The charger and USB PHY drivers are still being
discussed, but the binding for them has been acked by Rob and
Sebastian so they should be safe to merge together with the ADC
driver in Linux next that they depend on
* tag 'omap-for-v4.12/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap4-droid4: Add CPCAP PMIC OTG PHY configuration
ARM: dts: omap4-droid4: Add CPCAP PMIC battery charger configuration
ARM: dts: omap4-droid4: Add CPCAP PMIC ADC configuration
ARM: dts: omap4-droid4: Stop disabling SRAM and GPMC
ARM: dts: omap4-droid4: Fix interrupt triggering for cpcap
ARM: dts: am335x-icev2: Add CPSW ethernet0 and ethernet1
ARM: dts: am57xx-idk: Add DCAN support
Signed-off-by: Olof Johansson <olof@lixom.net>
i.MX device tree updates for 4.12:
- New board support: I2SE's i.MX28 Duckbill-2 boards, Gateworks Ventana
i.MX6 GW5903/GW5904, Zodiac Inflight Innovations RDU2 board, Engicam
i.CoreM6 Quad/Dual OpenFrame modules, Boundary Device i.MX6 Quad Plus
SOM.
- Improve compatible string for i.MX50 eSDHC, i.MX7S SRC devices and
i.MX6SX UART device.
- Add interrupts for switch and PHY devices on VF610 ZII Devel C board.
- Add LVDS, LCD backlight, touchscreen and SAI2 support for i.MX6
icore, geam, and isiot boards.
- A series from Lucas Stach to improve i.MX6Q Plus device tree and add
PRE/PRG devices.
- A series from Stefan Agner to update imx7-colibri device tree
regarding to display, PMIC/regulator support.
- Fix PCI bus DTC warnings seen with the latest compiler.
- Set default phy_type and dr_mode for i.MX25 USBOTG port.
- A couple of small improvements on i.MX25 pin function DT header.
- Add audio support for imx6q-cm-fx6 board using Wolfson wm8731 codec
which is muxed to SSI2 device.
- Other random updates, small fixes and trivial cleanups.
* tag 'imx-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (56 commits)
ARM: dts: imx6q-utilite-pro: add hpd gpio
ARM: dts: imx6qp-sabresd: Set reg_arm regulator supply
ARM: dts: imx6qdl-sabresd: Set LDO regulator supply
ARM: dts: imx: add Gateworks Ventana GW5903 support
ARM: dts: i.MX25: add AIPS control registers
ARM: dts: imx7-colibri: add Carrier Board 3.3V/5V regulators
ARM: dts: imx7-colibri: remove 1.8V fixed regulator
ARM: dts: imx7-colibri: allow to disable Ethernet rail
ARM: dts: imx7-colibri: fix PMIC voltages
ARM: dts: imx7-colibri: use OF graph to describe the display
ARM: dts: imx6qp-nitrogen6_som2: add Quad Plus variant of the SOM
ARM: dts: imx6q-icore: Add touchscreen node
ARM: dts: vf610-zii-dev-rev-b: change switch2 label
ARM: dts: imx6ul-[geam|isiot]: Add sai2 node
ARM: dts: imx6ul-isiot-common: Add touchscreen node
ARM: dts: imx6ul-isiot: Add i2c nodes
ARM: dts: imx6ul-isiot: Add imx6ul-isiot-common.dtsi
ARM: dts: imx6ul-isiot: Add backlight support for lcdif
ARM: dts: imx6ul-geam: Add backlight support for lcdif
ARM: dts: imx6: add ZII RDU2 boards
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Support for the usb-sata controller on the rock2 and another new rk3288
board, the phyCORE som and its PCM-947 carrier board from Phytec.
* tag 'v4.12-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: Add support for PCM-947 carrier board
dt-bindings: Document Phytec phyCORE-RK3288 RDK
ARM: dts: rockchip: Add support for phyCORE-RK3288 SoM
ARM: dts: rockchip: Enable sata support on rock2 square
Signed-off-by: Olof Johansson <olof@lixom.net>
Samsung DeviceTree ARM update for v4.12:
1. Enhancements to PCIe nodes on Exynos5440.
2. Fix thermal values on some of Exynos5420 boards like Odroid XU3.
3. Add proper clock frequency properties to DSI nodes.
4. Fix watchdog reset on Exynos4412.
5. Fix watchdog infinite interrupt in soft mode on Exynos4210,
Exynos5440, S3C64xx and S5Pv210.
6. Enable watchdog on Exynos4 and S3C SoCs.
* tag 'samsung-dt-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: add HDMI controller phandle to exynos4.dtsi
ARM: dts: s5pv210: Fix infinite interrupt in soft mode
ARM: dts: s3c64xx: Fix infinite interrupt in soft mode
ARM: dts: exynos: Fix infinite interrupt in soft mode on Exynos4210 and Exynos5440
ARM: dts: exynos: Enable watchdog on all Exynos4 boards
ARM: dts: s3c64xx: Enable watchdog on all S3C64xx boards
ARM: dts: exynos: Fix watchdog reset on Exynos4412
ARM: dts: exynos: Add the burst and esc clock frequency properties to DSI node
ARM: dts: exynos: Do not ignore real-world fuse values for thermal zone 0 on Exynos5420
ARM: dts: exynos: Add phy-pcie node for pcie to Exynos5440
Signed-off-by: Olof Johansson <olof@lixom.net>
mvebu dt for 4.12 (part 2)
Use disk-activity trigger for armada-385-linksys
Keep dts alphabetically ordered for clearfog (Armada 388)
* tag 'mvebu-dt-4.12-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-385-linksys: disk-activity trigger for all
ARM: dts: clearfog: keep dts alphabetically ordered
Signed-off-by: Olof Johansson <olof@lixom.net>
Second Round of Renesas ARM Based SoC DT Updates for v4.12
Corrections:
* Correct clock frequency of X2 DU clock input for r8a7791/koelsch board
* Correct Z clock for r8a7792 SoC
* Correct parent of SSI[0-9] clocks for r8a779[013] SoCs
* Correct ethernet clock parent on r7s72100 SoC
* Correct DU clock for r8a7794/silk board
Cleanups:
* Drop _clk suffix from external CAN clock node name on r8a779[01] SoCs
Enhancements:
* Enable rtc r7s72100/genmai board
* Add Z2 clock for r8a7794 SoC
* Add DU clock for r8a7794 SoC
* Add power-domains to SDHI for r8a7794 and r7s72100 SoCs
* Add reset control properties for r8a774[35] SoCs
* tag 'renesas-dt2-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (22 commits)
ARM: dts: r8a7791: Drop _clk suffix from external CAN clock node name
ARM: dts: r8a7790: Drop _clk suffix from external CAN clock node name
ARM: dts: genmai: Enable rtc and rtc_x1 clock
ARM: dts: rskrza1: add rtc DT support
ARM: dts: rskrza1: set rtc_x1 clock value
ARM: dts: r7s72100: add rtc to device tree
ARM: dts: r7s72100: add RTC_X clock inputs to device tree
ARM: dts: r7s72100: add rtc clock to device tree
ARM: dts: koelsch: Correct clock frequency of X2 DU clock input
ARM: dts: r8a7794: Add Z2 clock
ARM: dts: r8a7792: Correct Z clock
ARM: dts: r8a7793: Correct parent of SSI[0-9] clocks
ARM: dts: r8a7791: Correct parent of SSI[0-9] clocks
ARM: dts: r8a7790: Correct parent of SSI[0-9] clocks
ARM: dts: r7s72100: fix ethernet clock parent
ARM: dts: silk: Correct clock of DU1
ARM: dts: alt: Correct clock of DU1
ARM: dts: r8a7794: Correct clock of DU1
ARM: dts: r8a7794: Add DU1 clock to device tree
ARM: dts: r7s72100: add power-domains to sdhi
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Qualcomm Device Tree Changes for v4.12
* Add Coresight components for MSM8974
* Fixup MSM8974 ADSP XO clk and add RPMCC node
* Fix typo in APQ8060
* Add SDCs on MSM8660
* Revert MSM8974 USB gadget change due to issues
* tag 'qcom-dts-for-4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
Revert "ARM: dts: qcom: msm8974: Add USB gadget nodes"
ARM: dts: qcom: msm8974: Add RPMCC DT node
ARM: dts: fix typo on APQ8060 Dragonboard
ARM: dts: add SDC2 and SDC4 to the MSM8660 family
ARM: dts: msm8974: Hook up adsp-pil's xo clock
ARM: dts: qcom: Add msm8974 CoreSight components
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner H5 DT changes for 4.12
H5 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We then have patches to support the H5 boards on top.
* tag 'sunxi-dt-h5-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sunxi: h3/h5: switch apb0-related clocks to r_ccu
arm64: allwinner: h5: enable USB OTG on Orange Pi PC 2 board
arm64: allwinner: h5: add support for the Orange Pi PC 2 board
arm64: allwinner: h5: add Allwinner H5 .dtsi
ARM: sunxi: h3/h5: add usb_otg and OHCI/EHCI for usbc0 on H3/H5
arm: sun8i: h3: split Allwinner H3 .dtsi
arm: sun8i: h3: correct the GIC compatible in H3 to gic-400
arm: sun8i: h3: drop pinctrl-a10.h inclusion for H3 DTSI
arm: sun8i: h3: drop skeleton.dtsi inclusion in H3 DTSI
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner H3 DT changes for 4.12
H3 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.
We also have some new device addition (USB, mostly) that would conflict
otherwise.
* tag 'sunxi-dt-h3-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sun8i: h2+: enable USB OTG for Orange Pi Zero board
ARM: sun8i: h3: enable USB OTG on Orange Pi One
ARM: sunxi: h3/h5: add usb_otg and OHCI/EHCI for usbc0 on H3/H5
arm: sun8i: h3: split Allwinner H3 .dtsi
arm: sun8i: h3: correct the GIC compatible in H3 to gic-400
arm: sun8i: h3: drop pinctrl-a10.h inclusion for H3 DTSI
arm: sun8i: h3: drop skeleton.dtsi inclusion in H3 DTSI
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner DT changes for 4.12
As usual a number of changes, among which:
- All the sun5i DTSI has been reworked based on the new documentation and
the IPs that are actually found in all those SoCs. Part of that rework
also brought the GR8 DTSI to include sun5i.dtsi
- Mali devfreq and thermal throttling support on the A33
- AC power supplies for the AXP209 and AXP22X PMIC
- CAN support for the A20
- CPUFreq-based thermal throttling for the A33
- New board: NanoPi NEO Air
* tag 'sunxi-dt-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (38 commits)
ARM: sun8i: sina33: add highest OPP of CPUs
ARM: sun8i: a33: Add devfreq-based GPU cooling
ARM: sun8i: a33: add CPU thermal throttling
ARM: sun8i: a33: add thermal sensor
ARM: dts: sun7i: fix device node ordering
ARM: dts: sun4i: fix device node ordering
ARM: dts: sun7i: Add can0_pins_a pinctrl settings
ARM: dts: sun7i: Add CAN node
ARM: dts: sun4i: Add can0_pins_a pinctrl settings
ARM: dts: sun4i: Add CAN node
ARM: sun7i: cubietruck: enable ACIN und USB power supply subnode
ARM: dts: sun5i: Add interrupt for display backend
dt-bindings: display: sun4i: Add display backend interrupt to device tree binding
ARM: dts: sun7i: Use axp209.dtsi on A20-OLinuXino-Micro
ARM: dts: sun6i: sina31s: Enable SPDIF out
ARM: sun8i: sina33: add cpu-supply
ARM: sun8i: a33: add all operating points
ARM: sun5i: chip: enable ACIN power supply subnode
ARM: dts: sun8i: sina33: enable ACIN power supply subnode
ARM: dtsi: axp22x: add AC power supply subnode
...
Signed-off-by: Olof Johansson <olof@lixom.net>
SoCFPGA DTS updates for v4.12
- Clean-up:
- Add clock/memory nodes
- Add labels for CPU nodes
- Remove unused unit names and reg
- Remove unused skeleton.dtsi
- Add support for PMU
- Add QSPI for sodia board
- Add Reset controller for Arria10
* tag 'socfpga_dts_for_v4.12' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: Add Devkit A10-SR Reset Controller
ARM: dts: socfpga: sodia: enable qspi
ARM: dts: socfpga: Add support for PMU
ARM: dts: socfpga: Add labels for CPU nodes
ARM: dts: socfpga: Do not include skeleton.dtsi
ARM: dts: socfpga: Remove unit name for LEDs in EBV SOCrates
ARM: dts: socfpga: Remove unneeded reg from stmpe_touchscreen
ARM: dts: socfpga: Remove unneeded unit names
ARM: dts: socfpga: Add unit name to memory nodes
ARM: dts: socfpga: Add unit name to clock nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
A clean-up device-tree patch to ensure pinmux entry reuse.
* tag 'davinci-for-v4.12/dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850: move spi0_cs3_pin pinconf node
Signed-off-by: Olof Johansson <olof@lixom.net>
STM32 DT updates for v4.12, round 1
Highlights:
----------
- ADD RTC support on STM32F746 MCU
- Enable RTC on STM32F746 Eval board
- Enable clocks on STM32F746 MCU
- Enable DMA, pwm1 and pwm3 on STM32F429I Eval
- Add support of STM32H743 MCU and his Eval board
- Enable USB HS and FS on STM32F469 Disco board
* tag 'stm32-dt-for-v4.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
dt-bindings: Document the STM32 USB OTG DWC2 core binding
ARM: dts: stm32: Enable USB HS in FS mode (embedded phy) on stm32f429-disco
ARM: dts: stm32: Enable USB FS on stm32f469-disco
ARM: dts: stm32: Add USB FS support for STM32F429 MCU
ARM: dts: stm32: Add STM32H743 MCU and STM32H743i-EVAL board
ARM: dts: stm32: Enable pwm1 and pwm3 on stm32f429i-eval
ARM: dts: stm32: Enable dma by default on stm32f4 adc
ARM: dts: stm32: enable RTC on stm32746g-eval
ARM: dts: stm32: Add RTC support for STM32F746 MCU
ARM: dts: stm32: set HSE_RTC clock frequency to 1 MHz on stm32f746
dt-bindings: mfd: Add STM32F7 RCC numeric constants into DT include file
ARM: dts: stm32: Enable clocks for STM32F746 MCU
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes the following set of warnings on vexpress platforms:
sysreg@010000 simple-bus unit address format error, expected "10000"
sysctl@020000 simple-bus unit address format error, expected "20000"
i2c@030000 simple-bus unit address format error, expected "30000"
aaci@040000 simple-bus unit address format error, expected "40000"
mmci@050000 simple-bus unit address format error, expected "50000"
kmi@060000 simple-bus unit address format error, expected "60000"
kmi@070000 simple-bus unit address format error, expected "70000"
uart@090000 simple-bus unit address format error, expected "90000"
uart@0a0000 simple-bus unit address format error, expected "a0000"
uart@0b0000 simple-bus unit address format error, expected "b0000"
uart@0c0000 simple-bus unit address format error, expected "c0000"
wdt@0f0000 simple-bus unit address format error, expected "f0000"
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Pull ARM SoC fixes from Olof Johansson:
"Again, a batch that's been sitting a couple of weeks, mostly because
I anticipated a bit more material but it didn't show up -- which is
good.
These are all your garden variety fixes for ARM platforms.
The most visible issue fixed here is probably the SMP reset issue on
OMAP, the rest are minor stuff"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm64: allwinner: a64: add pmu0 regs for USB PHY
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
reset: add exported __reset_control_get, return NULL if optional
ARM: orion5x: only call into phylib when available
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
ARM: sun8i: a33: add operating-points-v2 property to all nodes
ARM: sun8i: a33: remove highest OPP to fix CPU crashes
Regression fix for omap interconnect code for deferred probe.
Without this fix we can get PM related warnings for devices that
use deferred probe. If necessary, this fix can wait for the
v4.12 merge window no problem.
* tag 'omap-for-v4.11/fixes-rc6-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap_device: Sync omap_device and pm_runtime after probe defer
ARM: omap2+: Revert omap-smp.c changes resetting CPU1 during boot
ARM: dts: am335x-evmsk: adjust mmc2 param to allow suspend
ARM: dts: ti: fix PCI bus dtc warnings
ARM: dts: am335x-baltos: disable EEE for Atheros 8035 PHY
ARM: dts: OMAP3: Fix MFG ID EEPROM
Signed-off-by: Olof Johansson <olof@lixom.net>
The envelope detector can analyze 6 different signals, selectable with a
mux controlled by three gpio pins.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
We found out that HW checksum generation only works from AST2500
onward. This disables it on AST2400 and removes the "no-hw-checksum"
properties in the device-trees. The problem we had wasn't related
to NC-SI.
Also rework the logic testing for that property so it can be used
to disable HW checksum generation and checking regardless of whether
NC-SI is used or not in case other variants out there need this.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We test for aspeed chips to handle a couple of special cases,
but we do that by checking the machine type which isn't right.
Instead check the actual device compatible property. This also
updates the dtsi files for the aspeed SoC to match.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently most nodes got labels to make them referenceable. The USB 3.0
nodes as well as the nodes for the SATA controllers were left out,
rectify the omission.
The labels "sataX" are already used by some boards for the SATA ports,
therefore use "ahciX" to label the SATA controller nodes.
To avoid potential confusion by labeling an USB3.0 controller "usb2" use
usb3_X as labels. This also coincides with the node names themselves
(usb@xxxxx vs usb3@xxxxx).
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The hpd pin of the second hdmi connector of the Utilite Pro is wired
up to a gpio pin of the SoC. Reflect this in the device tree.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
