Sometimes it is not desirable to bind SR-IOV VFs to drivers. This can save
host side resource usage by VF instances that will be assigned to VMs.
Add a new PCI sysfs interface "sriov_drivers_autoprobe" to control that
from the PF. To modify it, echo 0/n/N (disable probe) or 1/y/Y (enable
probe) to:
/sys/bus/pci/devices/<DOMAIN:BUS:DEVICE.FUNCTION>/sriov_drivers_autoprobe
Note that this must be done before enabling VFs. The change will not take
effect if VFs are already enabled. Simply, one can disable VFs by setting
sriov_numvfs to 0, choose whether to probe or not, and then re-enable the
VFs by restoring sriov_numvfs.
[bhelgaas: changelog, ABI doc]
Signed-off-by: Bodong Wang <bodong@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Device counting could be controlled by the level or the edges of
a trigger.
in_count0_enable_mode attibute allow to set the control mode.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
One of the features of STM32 trigger hardware block is a quadrature
encoder that can counts up/down depending of the levels and edges
of the selected external pins.
This patch allow to read/write the counter, get it direction,
set/get quadrature modes and get scale factor.
When counting up preset value is the limit of the counter.
When counting down the counter start from preset value down to 0.
This preset value could be set/get by using
/sys/bus/iio/devices/iio:deviceX/in_count0_preset attribute.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sometimes, the user needs to adjust some properties for controllers, eg
the role for controller, we add sysfs group for them.
The attribute 'role' is used to switch host/gadget role dynamically, the
uewr can read the current role, and write the other role compare to
current one to finish the switch.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
/sys/firmware/acpi/hotplug/force_remove was presumably added to support
auto offlining in the past. This is, however, inherently dangerous for
some hotplugable resources like memory. The memory offlining fails when
the memory is still in use and cannot be dropped or migrated. If we
ignore the failure we are basically allowing for subtle memory
corruption or a crash.
We have actually noticed the later while hitting BUG() during the memory
hotremove (remove_memory):
ret = walk_memory_range(PFN_DOWN(start), PFN_UP(start + size - 1), NULL,
check_memblock_offlined_cb);
if (ret)
BUG();
it took us quite non-trivial time realize that the customer had
force_remove enabled. Even if the BUG was removed here and we could
propagate the error up the call chain it wouldn't help at all because
then we would hit a crash or a memory corruption later and harder to
debug. So force_remove is unfixable for the memory hotremove. We haven't
checked other hotplugable resources to be prone to a similar problems.
Remove the force_remove functionality because it is not fixable currently.
Keep the sysfs file and report an error if somebody tries to enable it.
Encourage users to report about the missing functionality and work with
them with an alternative solution.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a few read-only sysfs attributes which provide some device information
that is exposed from the devices, primarily component and device names and
versions.
These are documented in Documentation/ABI/testing/sysfs-class-switchtec.
Tested-by: Krishna Dhulipala <krishnad@fb.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Stephen Bates <stephen.bates@microsemi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Wei Zhang <wzhang@fb.com>
Reviewed-by: Jens Axboe <axboe@fb.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Felipe writes:
usb: changes for v4.12
With 51 non-merge commits, this is one of the smallest USB Gadget pull
requests. Apart from your expected set of non-critical fixes, and
other miscellaneous items, we have most of the changes in dwc3 (52.5%)
with all other UDCs following with 34.8%.
As for the actual changes, the most important of them are all the
recent changes to reduce memory footprint of dwc3, bare minimum
dual-role support on dwc3 and reworked endpoint count and
initialization routines.
This patch adds support for usb role swap via sysfs "role".
For example:
1) Connect a usb cable using 2 Salvator-X boards.
- For A-Device, the cable is connected to CN11 (USB3.0 ch0).
- For B-Device, the cable is connected to CN9 (USB2.0 ch0).
2) On A-Device, you input the following command:
# echo peripheral > /sys/devices/platform/soc/ee020000.usb/role
3) On B-Device, you input the following command:
# echo host > /sys/devices/platform/soc/ee080200.usb-phy/role
Then, the A-Device acts as a peripheral and the B-Device acts as
a host. Please note that A-Device must input the following command
if you want the board to act as a host again.
# echo host > /sys/devices/platform/soc/ee020000.usb/role
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Now that we use the proper REQ_OP_WRITE_ZEROES operation everywhere we can
kill this hack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
/sys/devices/system/cpu/cpu#/cpu_capacity describe information about
CPUs heterogeneity (ref. to Documentation/devicetree/bindings/arm/
cpu-capacity.txt).
Add such description.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add documentation for max9611 driver.
Document attributes describing value of shunt resistor installed between
RS+ and RS- voltage sense inputs.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch updates the documentation related to the new files added for
qmap mux support.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The purpose of USB Type-C connector class is to provide
unified interface for the user space to get the status and
basic information about USB Type-C connectors on a system,
control over data role swapping, and when the port supports
USB Power Delivery, also control over power role swapping
and Alternate Modes.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-and-Tested-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The patch replaces 'the the' with 'the' in the documentation.
Signed-off-by: sayli karnik <karniksayli1995@gmail.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Change livepatch to use a basic per-task consistency model. This is the
foundation which will eventually enable us to patch those ~10% of
security patches which change function or data semantics. This is the
biggest remaining piece needed to make livepatch more generally useful.
This code stems from the design proposal made by Vojtech [1] in November
2014. It's a hybrid of kGraft and kpatch: it uses kGraft's per-task
consistency and syscall barrier switching combined with kpatch's stack
trace switching. There are also a number of fallback options which make
it quite flexible.
Patches are applied on a per-task basis, when the task is deemed safe to
switch over. When a patch is enabled, livepatch enters into a
transition state where tasks are converging to the patched state.
Usually this transition state can complete in a few seconds. The same
sequence occurs when a patch is disabled, except the tasks converge from
the patched state to the unpatched state.
An interrupt handler inherits the patched state of the task it
interrupts. The same is true for forked tasks: the child inherits the
patched state of the parent.
Livepatch uses several complementary approaches to determine when it's
safe to patch tasks:
1. The first and most effective approach is stack checking of sleeping
tasks. If no affected functions are on the stack of a given task,
the task is patched. In most cases this will patch most or all of
the tasks on the first try. Otherwise it'll keep trying
periodically. This option is only available if the architecture has
reliable stacks (HAVE_RELIABLE_STACKTRACE).
2. The second approach, if needed, is kernel exit switching. A
task is switched when it returns to user space from a system call, a
user space IRQ, or a signal. It's useful in the following cases:
a) Patching I/O-bound user tasks which are sleeping on an affected
function. In this case you have to send SIGSTOP and SIGCONT to
force it to exit the kernel and be patched.
b) Patching CPU-bound user tasks. If the task is highly CPU-bound
then it will get patched the next time it gets interrupted by an
IRQ.
c) In the future it could be useful for applying patches for
architectures which don't yet have HAVE_RELIABLE_STACKTRACE. In
this case you would have to signal most of the tasks on the
system. However this isn't supported yet because there's
currently no way to patch kthreads without
HAVE_RELIABLE_STACKTRACE.
3. For idle "swapper" tasks, since they don't ever exit the kernel, they
instead have a klp_update_patch_state() call in the idle loop which
allows them to be patched before the CPU enters the idle state.
(Note there's not yet such an approach for kthreads.)
All the above approaches may be skipped by setting the 'immediate' flag
in the 'klp_patch' struct, which will disable per-task consistency and
patch all tasks immediately. This can be useful if the patch doesn't
change any function or data semantics. Note that, even with this flag
set, it's possible that some tasks may still be running with an old
version of the function, until that function returns.
There's also an 'immediate' flag in the 'klp_func' struct which allows
you to specify that certain functions in the patch can be applied
without per-task consistency. This might be useful if you want to patch
a common function like schedule(), and the function change doesn't need
consistency but the rest of the patch does.
For architectures which don't have HAVE_RELIABLE_STACKTRACE, the user
must set patch->immediate which causes all tasks to be patched
immediately. This option should be used with care, only when the patch
doesn't change any function or data semantics.
In the future, architectures which don't have HAVE_RELIABLE_STACKTRACE
may be allowed to use per-task consistency if we can come up with
another way to patch kthreads.
The /sys/kernel/livepatch/<patch>/transition file shows whether a patch
is in transition. Only a single patch (the topmost patch on the stack)
can be in transition at a given time. A patch can remain in transition
indefinitely, if any of the tasks are stuck in the initial patch state.
A transition can be reversed and effectively canceled by writing the
opposite value to the /sys/kernel/livepatch/<patch>/enabled file while
the transition is in progress. Then all the tasks will attempt to
converge back to the original patch state.
[1] https://lkml.kernel.org/r/20141107140458.GA21774@suse.cz
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Acked-by: Miroslav Benes <mbenes@suse.cz>
Acked-by: Ingo Molnar <mingo@kernel.org> # for the scheduler changes
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Jonathan writes:
First set of IIO new device support, features and cleanup for the 4.12 cycle.
Quite a bit of outreachy activity here with a driver from a current intern
and a number of cleanup patches as part of the next round.
Getting a pull request in early this cycle as it's looking like another large
cycle for IIO.
New device support
* adxl345
- initial device support. Note, once complete support is done the intent
is to superceded the driver in input/misc.
- bindings.
- conversion from i2c direct calls to regmap and driver split.
- spi support.
* chromeos light and proximity.
- new driver.
* devantech srf04 ultrasonic ranger
- new driver with device tree bindings.
* hid temperature
- new driver for environemntal temperature support from hid devices.
* max30102 oximeter
- new driver with device tree bindings.
* st lsm6dsx
- refactor and addition of device support for lsm6dsl and lsm6ds3h.
Staging graduation
* isl29028 including copyright notice update to reflect Brian's work.
* lpc32xx_adc.
* spear adc. It's not perfect and there are some datasheet disagreements, but
it works and is good enough to graduate.
New features
* documentation
- abi docs for in_proximity_sampling_frequency_available.
- generalise counting direction ABI docs as a second driver is going to
use them.
* hid-sensor-prox
- Add support for HID_USAGE_SENSOR_HUMAN_PRESENCE if used on a particular
device.
* isl29028
- runtime pm.
* meson-saradc
- switch from polling to interrupt mode and improved read_raw_sample function
to avoid unnecessary loop.
* tmp007
- interrupt and threshold event support.
Cleanups and minor fixes
* ad2s1210
- permissions to octal.
* ad7192
- permissions to octal.
- use BIT macro.
* ad9832
- merge header definitions into source file.
* ad9834
- merge header definitions into source file.
* ade7753
- merge header definitions into source file.
- cleanup include ordering.
* ade7854
- simplify return logic.
* adis16201
- merge header definitions into source file.
- rename _core.c to .c as there is nothing else.
* adis16203
- merge header definitions into source file.
- rename _core.c to .c as there is nothing else.
* adis16209
- merge header definitions into source file.
- rename _core.c to .c as there is nothing else.
* adis16240
- permissions to octal.
- merge header definitions into source file.
- rename _core.c to .c as there is nothing else.
* adt7136
- permissions to octal.
* cio-dac
- set missing parent device.
* documentation
- update version numbers on sysfs ABI for counter bits that didn't quite.
make 4.9.
* isl29028
- mdelay to msleep.
- incorrrect sleep time when taking first proximity reading.
* lmp91000
- set missing parent device.
* lpc32xx
- Consistent prefixes for defines.
- rename local state structure to _state.
* max30100
- set missing parent device.
* max30102
- set missing parent device.
* maxim-thermocouple
- set missing parent device.
* meter driver header
- permissions to octal.
* pulsedlight-lidar-lite-v2
- set missing parent device.
* quad-8
- set missing parent device.
* st104
- set missing parent device.
Other
* Mailmap
- update Matt Ranostay's email address to the Konsolko one.
Move counting direction documentation for 104-quad-8 to sysfs-bus-iio
to avoid duplicated for other incoming drivers
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Pull RTC updates from Alexandre Belloni:
"Subsystem:
- constify rtc_class_ops structures
New driver:
- STM32
Drivers:
- armada38x: fix errata, Armada 7K/8K support
- ds3232: fix wakeup support
- gemini: DT support
- m48t86: huge cleanup and platform_data removal
- mcp795: alarm support
- sun6i: proper oscillator handling
- tegra: proper clock handling
- tps65910: calibration support"
* tag 'rtc-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (44 commits)
rtc: ds3232: Call device_init_wakeup before device_register
rtc: pcf2127: bulk read only date and time registers.
rtc: armada38x: Add support for Armada 7K/8K
rtc: armada38x: Prepare driver to manage different versions
rtc: ds3232: Add regmap max_register definition.
rtc: ds3232: Cleanup whitespace around register and bit definitions.
rtc: m48t86: remove unused platform_data
ARM: Orion5x: ts78xx: allow rtc-m48t86 to manage it's own resources
ARM: Orion5x: ts78xx: remove RTC detection
ARM: ep93xx: ts72xx: allow rtc-m48t86 to manage its own resources
rtc: m48t86: verify that the RTC is actually present
rtc: m48t86: add NVRAM support
rtc: m48t86: allow driver to manage its resources
rtc: m48t86: shorten register name defines
bindings: rtc: correct wrong reference in required properties
rtc: sun6i: Fix return value check in sun6i_rtc_clk_init()
rtc: sun6i: extend test coverage
rtc: sun6i: Fix compatibility with old DT binding
rtc: snvs: add a missing write sync
rtc: bq32000: add support to enable disable the trickle charge FET bypass
...
Pull rdma updates from Doug Ledford:
"First set of updates for 4.11 kernel merge window
- Add new Broadcom bnxt_re RoCE driver
- rxe driver updates
- ioctl cleanups
- ETH_P_IBOE declaration cleanup
- IPoIB changes
- Add port state cache
- Allow srpt driver to accept guids as port names in config
- Update to hfi1 driver
- Update to srp driver
- Lots of misc minor changes all over"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (114 commits)
RDMA/bnxt_re: fix for "bnxt_en: Update to firmware interface spec 1.7.0."
rdma_cm: fail iwarp accepts w/o connection params
IB/srp: Drain the send queue before destroying a QP
IB/core: Add support for draining IB_POLL_DIRECT completion queues
IB/srp: Improve an error path
IB/srp: Make a diagnostic message more informative
IB/srp: Document locking conventions
IB/srp: Fix race conditions related to task management
IB/srp: Avoid that duplicate responses trigger a kernel bug
IB/SRP: Avoid using IB_MR_TYPE_SG_GAPS
RDMA/qedr: Fix some error handling
RDMA/bnxt_re: add DCB dependency
IB/hns: include linux/module.h
IB/vmw_pvrdma: Expose vendor error to ULPs
vmw_pvrdma: switch to pci_alloc_irq_vectors
IB/hfi1: use size_t for passing array length
IB/ipoib: Remove redudant label
IB/ipoib: remove the unnecessary memory free
IB/mthca: switch to pci_alloc_irq_vectors
IB/hfi1: Code reuse with memdup_copy
...
We had a deprecated_attr_warn() warning for 2 years and now the time has
come and we finally can do the cleanup.
The plan was as follows:
: per-stat sysfs attributes are considered to be deprecated.
: The basic strategy is:
: -- the existing RW nodes will be downgraded to WO nodes (in linux 4.11)
: -- deprecated RO sysfs nodes will eventually be removed (in linux 4.11)
:
: The list of deprecated attributes can be found here:
: Documentation/ABI/obsolete/sysfs-block-zram
:
: Basically, every attribute that has its own read accessible sysfs
: node (e.g. num_reads) *AND* is accessible via one of the stat files
: (zram<id>/stat or zram<id>/io_stat or zram<id>/mm_stat) is considered
: to be deprecated.
The patch also removes `obsolete/sysfs-block-zram', clean ups
`testing/sysfs-block-zram' and tweaks zram.txt files.
Link: http://lkml.kernel.org/r/20170118035838.11090-1-sergey.senozhatsky@gmail.com
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull staging/iio driver updates from Greg KH:
"Here is the big staging and iio driver patchsets for 4.11-rc1.
We almost broke even this time around, with only a few thousand lines
added overall, as we removed the old and obsolete i4l code, but added
some new drivers for the RPi platform, as well as adding some new IIO
drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'staging-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (669 commits)
Staging: vc04_services: Fix the "space prohibited" code style errors
Staging: vc04_services: Fix the "wrong indent" code style errors
staging: octeon: Use net_device_stats from struct net_device
Staging: rtl8192u: ieee80211: ieee80211.h - style fix
Staging: rtl8192u: ieee80211: ieee80211_tx.c - style fix
Staging: rtl8192u: ieee80211: rtl819x_BAProc.c - style fix
Staging: rtl8192u: ieee80211: ieee80211_module.c - style fix
Staging: rtl8192u: ieee80211: rtl819x_TSProc.c - style fix
Staging: rtl8192u: r8192U.h - style fix
Staging: rtl8192u: r8192U_core.c - style fix
Staging: rtl8192u: r819xU_cmdpkt.c - style fix
staging: rtl8192u: blank lines aren't necessary before a close brace '}'
staging: rtl8192u: Adding space after enum and struct definition
staging: rtl8192u: Adding space after struct definition
Staging: ks7010: Add required and preferred spaces around operators
Staging: ks7010: ks*: Remove redundant blank lines
Staging: ks7010: ks*: Add missing blank lines after declarations
staging: visorbus, replace init_timer with setup_timer
staging: vt6656: rxtx.c Removed multiple dereferencing
staging: vt6656: Alignment match open parenthesis
...
Pull dmaengine updates from Vinod Koul:
"This time we fairly boring and bit small update.
- Support for Intel iDMA 32-bit hardware
- deprecate broken support for channel switching in async_tx
- bunch of updates on stm32-dma
- Cyclic support for zx dma and making in generic zx dma driver
- Small updates to bunch of other drivers"
* tag 'dmaengine-4.11-rc1' of git://git.infradead.org/users/vkoul/slave-dma: (29 commits)
async_tx: deprecate broken support for channel switching
dmaengine: rcar-dmac: Widen DMA mask to 40 bits
dmaengine: sun6i: allow build on ARM64 platforms (sun50i)
dmaengine: Provide a wrapper for memcpy operations
dmaengine: zx: fix build warning
dmaengine: dw: we do support Merrifield SoC in PCI mode
dmaengine: dw: add support of iDMA 32-bit hardware
dmaengine: dw: introduce register mappings for iDMA 32-bit
dmaengine: dw: introduce block2bytes() and bytes2block()
dmaengine: dw: extract dwc_chan_pause() for future use
dmaengine: dw: replace convert_burst() with one liner
dmaengine: dw: register IRQ and DMA pool with instance ID
dmaengine: dw: Fix data corruption in large device to memory transfers
dmaengine: ste_dma40: indicate granularity on channels
dmaengine: ste_dma40: indicate directions on channels
dmaengine: stm32-dma: Add error messages if xlate fails
dmaengine: dw: pci: remove LPE Audio DMA ID
dmaengine: stm32-dma: Add max_burst support
dmaengine: stm32-dma: Add synchronization support
dmaengine: stm32-dma: Fix residue computation issue in cyclic mode
...
Pull media updates from Mauro Carvalho Chehab:
- new drivers:
- i.MX6 Video Data Order Adapter's (VDOA)
- Toshiba et8ek8 5MP sensor
- STM DELTA multi-format video decoder V4L2 driver
- SPI connected IR LED
- Mediatek IR remote receiver
- ZyDAS ZD1301 DVB USB interface driver
- new RC keymaps
- some very old LIRC drivers got removed from staging
- RC core gained support encoding IR scan codes
- DVB si2168 gained support for DVBv5 statistics
- lirc_sir driver ported to rc-core and promoted from staging
- other bug fixes, board additions and driver improvements
* tag 'media/v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (230 commits)
[media] mtk-vcodec: fix build warnings without DEBUG
[media] zd1301: fix building interface driver without demodulator
[media] usbtv: add sharpness control
[media] cxusb: Use a dma capable buffer also for reading
[media] ttpci: address stringop overflow warning
[media] dvb-usb-v2: avoid use-after-free
[media] add Hama Hybrid DVB-T Stick support
[media] et8ek8: Fix compiler / Coccinelle warnings
[media] media: fix semicolon.cocci warnings
[media] media: exynos4-is: add flags to dummy Exynos IS i2c adapter
[media] v4l: of: check for unique lanes in data-lanes and clock-lanes
[media] coda/imx-vdoa: constify structs
[media] st-delta: debug: trace stream/frame information & summary
[media] st-delta: add mjpeg support
[media] st-delta: EOS (End Of Stream) support
[media] st-delta: rpmsg ipc support
[media] st-delta: add memory allocator helper functions
[media] st-delta: STiH4xx multi-format video decoder v4l2 driver
[media] MAINTAINERS: add st-delta driver
[media] ARM: multi_v7_defconfig: enable STMicroelectronics DELTA Support
...
Pull power management updates from Rafael Wysocki:
"The majority of changes go into the Operating Performance Points (OPP)
framework and cpufreq this time, followed by devfreq and some
scattered updates all over.
The OPP changes are mostly related to switching over from RCU-based
synchronization, that turned out to be overly complicated and
problematic, to reference counting using krefs.
In the cpufreq land there are core cleanups, documentation updates, a
new driver for Broadcom BMIPS SoCs, a new cpufreq-dt sub-driver for TI
SoCs that require special handling, ARM64 SoCs support for the qoriq
driver, intel_pstate updates, powernv driver update and assorted
fixes.
The devfreq changes are mostly fixes related to the sysfs interface
and some Exynos drivers updates.
Apart from that, the cpuidle menu governor will support per-CPU PM QoS
constraints for the wakeup latency now, some bugs in the wakeup IRQs
framework are fixed, the generic power domains framework should handle
asynchronous invocations of *noirq suspend/resume callbacks from now
on, the analyze_suspend.py script is updated and there is a new tool
for intel_pstate diagnostics.
Specifics:
- Operating Performance Points (OPP) framework fixes, cleanups and
switch over from RCU-based synchronization to reference counting
using krefs (Viresh Kumar, Wei Yongjun, Dave Gerlach)
- cpufreq core cleanups and documentation updates (Viresh Kumar,
Rafael Wysocki)
- New cpufreq driver for Broadcom BMIPS SoCs (Markus Mayer)
- New cpufreq-dt sub-driver for TI SoCs requiring special handling,
like in the AM335x, AM437x, DRA7x, and AM57x families, along with
new DT bindings for it (Dave Gerlach, Paul Gortmaker)
- ARM64 SoCs support for the qoriq cpufreq driver (Tang Yuantian)
- intel_pstate driver updates including a new sysfs knob to control
the driver's operation mode and fixes related to the no_turbo sysfs
knob and the hardware-managed P-states feature support (Rafael
Wysocki, Srinivas Pandruvada)
- New interface to export ultra-turbo frequencies for the powernv
cpufreq driver (Shilpasri Bhat)
- Assorted fixes for cpufreq drivers (Arnd Bergmann, Dan Carpenter,
Wei Yongjun)
- devfreq core fixes, mostly related to the sysfs interface exported
by it (Chanwoo Choi, Chris Diamand)
- Updates of the exynos-bus and exynos-ppmu devfreq drivers (Chanwoo
Choi)
- Device PM QoS extension to support CPUs and support for per-CPU
wakeup (device resume) latency constraints in the cpuidle menu
governor (Alex Shi)
- Wakeup IRQs framework fixes (Grygorii Strashko)
- Generic power domains framework update including a fix to make it
handle asynchronous invocations of *noirq suspend/resume callbacks
correctly (Ulf Hansson, Geert Uytterhoeven)
- Assorted fixes and cleanups in the core suspend/hibernate code, PM
QoS framework and x86 ACPI idle support code (Corentin Labbe, Geert
Uytterhoeven, Geliang Tang, John Keeping, Nick Desaulniers)
- Update of the analyze_suspend.py script is updated to version 4.5
offering multiple improvements (Todd Brandt)
- New tool for intel_pstate diagnostics using the pstate_sample
tracepoint (Doug Smythies)"
* tag 'pm-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (85 commits)
MAINTAINERS: cpufreq: add bmips-cpufreq.c
PM / QoS: Fix memory leak on resume_latency.notifiers
PM / Documentation: Spelling s/wrtie/write/
PM / sleep: Fix test_suspend after sleep state rework
cpufreq: CPPC: add ACPI_PROCESSOR dependency
cpufreq: make ti-cpufreq explicitly non-modular
cpufreq: Do not clear real_cpus mask on policy init
tools/power/x86: Debug utility for intel_pstate driver
AnalyzeSuspend: fix drag and zoom bug in javascript
PM / wakeirq: report a wakeup_event on dedicated wekup irq
PM / wakeirq: Fix spurious wake-up events for dedicated wakeirqs
PM / wakeirq: Enable dedicated wakeirq for suspend
cpufreq: dt: Don't use generic platdev driver for ti-cpufreq platforms
cpufreq: ti: Add cpufreq driver to determine available OPPs at runtime
Documentation: dt: add bindings for ti-cpufreq
PM / OPP: Expose _of_get_opp_desc_node as dev_pm_opp API
cpufreq: qoriq: Don't look at clock implementation details
cpufreq: qoriq: add ARM64 SoCs support
PM / Domains: Provide dummy governors if CONFIG_PM_GENERIC_DOMAINS=n
cpufreq: brcmstb-avs-cpufreq: remove unnecessary platform_set_drvdata()
...
Pull LED updates from Jacek Anaszewski:
"New features and improvements:
- add new optional brightness_hw_changed attribute for the LEDs that
may have their brightness level changed autonomously (outside of
kernel control) by hardware / firmware. The attribute supports
userspace notifications through POLLPRI events
- add led_brightness_hw_mon tool that demonstrates how to use the
aforementioned feature
- add LED_ON enum for LEDs that can be only turned on/off, and don't
allow setting other brightness levels
- allow for adjusting heartbeat trigger blink brightness level
Fixes and cleanups:
- avoid harmless maybe-uninitialized warning in leds-ktd2692.c
- add context to the existing example entries in common LED bindings
to make the documentation more clear"
* tag 'leds_for_4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: ledtrig-heartbeat: Make top brightness adjustable
tools/leds: Add led_hw_brightness_mon program
leds: class: Add new optional brightness_hw_changed attribute
leds: ktd2692: avoid harmless maybe-uninitialized warning
leds: add LED_ON brightness as boolean value
DT: leds: Improve examples by adding some context
Pull IOMMU UPDATES from Joerg Roedel:
- KVM PCIe/MSI passthrough support on ARM/ARM64
- introduction of a core representation for individual hardware iommus
- support for IOMMU privileged mappings as supported by some ARM IOMMUS
- 16-bit SID support for ARM-SMMUv2
- stream table optimization for ARM-SMMUv3
- various fixes and other small improvements
* tag 'iommu-updates-v4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (61 commits)
vfio/type1: Fix error return code in vfio_iommu_type1_attach_group()
iommu: Remove iommu_register_instance interface
iommu/exynos: Make use of iommu_device_register interface
iommu/mediatek: Make use of iommu_device_register interface
iommu/msm: Make use of iommu_device_register interface
iommu/arm-smmu: Make use of the iommu_register interface
iommu: Add iommu_device_set_fwnode() interface
iommu: Make iommu_device_link/unlink take a struct iommu_device
iommu: Add sysfs bindings for struct iommu_device
iommu: Introduce new 'struct iommu_device'
iommu: Rename struct iommu_device
iommu: Rename iommu_get_instance()
iommu: Fix static checker warning in iommu_insert_device_resv_regions
iommu: Avoid unnecessary assignment of dev->iommu_fwspec
iommu/mediatek: Remove bogus 'select' statements
iommu/dma: Remove bogus dma_supported() implementation
iommu/ipmmu-vmsa: Restrict IOMMU Domain Geometry to 32-bit address space
iommu/vt-d: Don't over-free page table directories
iommu/vt-d: Tylersburg isoch identity map check is done too late.
iommu/vt-d: Fix some macros that are incorrectly specified in intel-iommu
...
Pull EDAC updates from Borislav Petkov:
- Make amd64_edac still load on a machine with unpopulated nodes +
cleanups (Yazen Ghannam)
- Expose per-DIMM error counts in sysfs (Aaron Miller)
- Add T2080 l2-cache support to mpc85xx (Chris Packham)
- Random other small improvements/cleanups/fixlets
* tag 'edac_for_4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, mce_amd: Print IPID and Syndrome on a separate line
EDAC, amd64: Bump driver version
MAINTAINERS, EDAC: Update email for Thor Thayer
EDAC, fsl_ddr: Make locally used symbols static
EDAC, mpc85xx: Add T2080 l2-cache support
EDAC, amd64: Add x86cpuid sanity check during init
EDAC, amd64: Don't treat ECC disabled as failure
EDAC: Add routine to check if MC devices list is empty
EDAC, amd64: Remove unused printing macros
EDAC, amd64: Rework messages in ecc_enabled()
EDAC, amd64: Move global code out of instance functions
EDAC, amd64: Free unused memory when init_one_instance() fails
EDAC, mce_amd: Give more context to deferred error message
EDAC, i7300: Test for the second channel properly
EDAC, sb_edac: Get rid of ->show_interleave_mode()
EDAC: Expose per-DIMM error counts in sysfs
EDAC, amd64: Save and return err code from probe_one_instance()
EDAC, i82975x: Add ioremap_nocache() error handling
EDAC: Fix typos in enum mem_type comments
EDAC: Make dev_attr_sdram_scrub_rate static
Add new entry to the RDMA-CM configfs that allows users
to select default TOS for RDMA-CM QPs.
This is useful for users that want to control the TOS for legacy
applications without changing their code.
Application that sets the TOS explicitly using the rdma_set_option
API will continue to work as expected, meaning overriding the configfs
value.
CC: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Reviewed-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The ACCES 104-QUAD-8 IIO driver did not appear in the 4.9 version of the
Linux kernel. This patch fixes the KernelVersion lines of the 104-QUAD-8
sysfs ABI documentation.
Fixes: 28e5d3bb03 ("iio: 104-quad-8: Add IIO support for the ACCES 104-QUAD-8")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The IIO counter driver support did not appear in the 4.9 version of the
Linux kernel. This patch fixes the KernelVersion lines of the relevant
IIO counter sysfs ABI documentation.
Fixes: 1a8f324aa1 ("iio: Implement counter channel type and info constants")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add entry for the in_proximity_sampling_frequency_available sysfs
entry to the existing sampling_frequency_available ABI documentation.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This resolves the merge errors that were reported in linux-next and it
picks up the staging and IIO fixes that we need/want in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bq32000 includes a trickle charge circuit to maintain the charge of the
backup supply when a super capacitor is used.
You can enable the charging circuit by setting 'trickle-resistor-ohms',
additionally you can set TCFE to 1 to bypass the internal diode and boost
the charge voltage of the backup supply. You might want to enable/disable
the TCFE switch from userspace (e.g when device is only connected to a
battery)
This patch introduces a new sysfs entry to enable and disable this FET
form userspace.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
This patch just removes '.' character from the sysfs name of devfreq-event
device as following. Usually, the subsystem uses the similiar naming style
such as {framework name}{Number}.
- old : /sys/class/devfreq-event/event.(X)
- new : /sys/class/devfreq-event/event(X)
And this patch initializes the value of 'event_no' with -1
in order to remove the unneeded operation (-1) when calling
the atomic_inc_return(&event_no).
Lastly, this patch adds the ABI document for devfreq-event class.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
For IR wakeup, a driver has to program the hardware to wakeup at a
specific IR sequence, so it makes no sense to allow multiple wakeup
protocols to be selected. In the same manner the sysfs interface only
allows one scancode to be provided.
In addition, we need to know the specific variant of the protocol.
In short, these changes are made to the wakeup_protocols sysfs entry:
- list all the protocol variants rather than the protocol groups,
e.g. "nec nec-x nec-32" rather than just "nec".
- only allow one protocol variant to be selected rather than multiple
- wakeup_filter can only be set once a protocol has been selected in
wakeup_protocols.
This is an API change, however the only user of this API is the img-ir,
but the wakeup code was never merged to mainline, so it was never used.
Signed-off-by: Sean Young <sean@mess.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Sifan Naeem <sifan.naeem@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Some LEDs may have their brightness level changed autonomously
(outside of kernel control) by hardware / firmware. This commit
adds support for an optional brightness_hw_changed attribute to
signal such changes to userspace (if a driver can detect them):
What: /sys/class/leds/<led>/brightness_hw_changed
Date: January 2017
KernelVersion: 4.11
Description:
Last hardware set brightness level for this LED. Some LEDs
may be changed autonomously by hardware/firmware. Only LEDs
where this happens and the driver can detect this, will
have this file.
This file supports poll() to detect when the hardware
changes the brightness.
Reading this file will return the last brightness level set
by the hardware, this may be different from the current
brightness.
Drivers which want to support this, simply add LED_BRIGHT_HW_CHANGED to
their flags field and call led_classdev_notify_brightness_hw_changed()
with the hardware set brightness when they detect a hardware / firmware
triggered brightness change.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Define extended attribute so that user may choose rising, falling or both
edges for external trigger sources.
Default to rising edge in case it isn't set.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Immutable branch between MFD, IIO and PWM due for the v4.11 merge window
Pulled into IIO to allow follow up series of triggered capture for the
STM32 ADCs.
Add sysfs-bus-iio-distance-srf08 for individual attributes of the driver,
especially:
- sensitivity which the device documentation calls gain for amplifying the
signal
- max_range for limiting the maximum distance for expected echos and
therefore limiting the time waiting for telegrams
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Timers IPs can be used to generate triggers for other IPs like
DAC or ADC.
Each trigger may result of timer internals signals like counter enable,
reset or edge, this configuration could be done through "master_mode"
device attribute.
Since triggers could be used by DAC or ADC their names are defined
in include/ nux/iio/timer/stm32-timer-trigger.h and is_stm32_iio_timer_trigger
function could be used to check if the trigger is valid or not.
"trgo" trigger have a "sampling_frequency" attribute which allow to configure
timer sampling frequency.
version 8:
- change kernel version from 4.10 to 4.11 in ABI documentation
version 7:
- remove all iio_device related code
- move driver into trigger directory
version 5:
- simplify tables of triggers
- only create an IIO device when needed
version 4:
- get triggers configuration from "reg" in DT
- add tables of triggers
- sampling frequency is enable/disable when writing in trigger
sampling_frequency attribute
- no more use of interruptions
version 3:
- change compatible to "st,stm32-timer-trigger"
- fix attributes access right
- use string instead of int for master_mode and slave_mode
- document device attributes in sysfs-bus-iio-timer-stm32
version 2:
- keep only one compatible
- use st,input-triggers-names and st,output-triggers-names
to know which triggers are accepted and/or create by the device
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
A new iommu-group sysfs attribute file is introduced. It contains
the list of reserved regions for the iommu-group. Each reserved
region is described on a separate line:
- first field is the start IOVA address,
- second is the end IOVA address,
- third is the type.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Tomasz Nowicki <tomasz.nowicki@caviumnetworks.com>
Tested-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Jonathan writes:
Second round of IIO new device support, cleanups and features for the 4.11 cycle
New device support:
* lsm6dsx imu
- new driver and bindings.
* max11100 adc
- new driver and bindings.
* tlc4541
- new driver
* tmp007 thermopile
- new driver.
Core
* in kernel interfaces
- pass through raw values if no scaling provided and a processed value is
requested.
* trigger
- close a race condition in acquiring trigger reference.
- constify device_type structures.
- rework the viio_trigger_alloc function to be much neater and easier to
read.
- free trigger resources correctly on some error paths. Avoids putting a
module we don't have.
Documentation
* ABI
- specify a unit for proximity measurements.
Cleanups and features
* ads1015
- constify iio_info structure.
* ads7950 cleanups following merge in previous pull
- Add device tree bindings
- Drop the ti prefix from the module name in common with other drivers.
- Change regulator name to vref to match datasheet and other drivers.
* ak8974
- remove a redundant zero timeout check.
* bmi160
- use variable names for sizeof instead of types.
* cm3605
- mark PM functions as __maybe_unused to avoid a build warning.
* isl29028 (on it's way towards moving out of staging).
- alignment fixes and newline improvements.
- combine proxim_get and read_proxim for simpler code.
- drop unused ISL29028_DEV_ATTR macro
- move some error logging into functions to cut out repitition.
- make error messages more consistent.
- tidy up some brackets.
- drop the enable flag that nothing uses.
- only set proximity rate and ALS scale when relevant channel type is enabled.
- runtime pm support.
* lsm6dsx
- fix wrong values for gyro sensitivitiy.
* mag3110
- claim direct mode during sysfs reads to avoid a race condition.
* max1363
- export OF device table IDs as module aliases.
* max30100
- use msleep for long uncritical delays.
* mcp4531
- export OF device table as module aliases.
* ms5611
- claim direct mode during sysfs reads to avoid a race condition.
* opt3001
- export OF device table as module aliases.
* sx9500
- claim direct mode during oversampling changes to avoid a race condition.
Jonathan writes:
First round of new device support, features and cleanups for IIO in the 4.11 cycle.
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
To follow iio guidelines Where possible we stick to the raw SI unit, so
specify meters for proximity.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
