From Tony Lindgren:
Display related clean-up from Tomi Valkeinen.
These were separated from the DSS driver changes to leave out
a dependency between the driver and arch/arm related code.
* tag 'omap-for-v3.10/dss-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
arm: dss-common: don't use reset_gpio from omap4_panda_dvi_device
arm: omap boards: Remove unnecessary platform_enable/disable callbacks for VENC devices
arm: omap: dss-common: use picodlp panel's gpio handling
arm: omap: board-omap3pandora: use tpo panel's gpio handling
arm: omap: board-zoom: use NEC panel's gpio handling
arm: omap: board-rx-51: use acx565akm panel's gpio handling
arm: omap: board-sdp3430: use sharp panel's gpio handling
arm: omap: board-omap3evm: use sharp panel's gpio handling
arm: omap: board-overo: use lb035q02 dpi panel's gpio handling
arm: omap: board-ldp: use generic dpi panel's gpio handling
arm: omap: board-am3517: use generic dpi panel's gpio handling
arm: omap: board-cm-t35: use generic dpi panel's gpio handling
arm: omap: board-devkit8000: use generic dpi panel's gpio handling
arm: omap: board-2430: use generic dpi panel's gpio handling
ARM: OMAP: zoom: Use pwm stack for lcd and keyboard backlight
OMAPDSS: add fields to panels' platform data
OMAPDSS: panels: keep platform data of all panels in a single header
Conflicts:
arch/arm/mach-omap2/board-2430sdp.c
arch/arm/mach-omap2/board-zoom-display.c
This patch adds all necessary header files and Kbuild plumbing for the
core driver for Silicon Laboratories Si476x series of AM/FM tuner
chips.
The driver as a whole is implemented as an MFD device and this patch
adds a core portion of it that provides all the necessary
functionality to the two other drivers that represent radio and audio
codec subsystems of the chip.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
RTS5249 supports SD UHS-II interface.
In order to support SD UHS-II，the definitions of some internal
registers of RTS5249 have to be modified and are different from its
predecessors. So we need this patch to ensure RTS5249 can work, even
SD/MMC stack doesn't support UHS-II interface.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull fuse build fix from Miklos Szeredi:
"This fixes android builds. The patch appears large, but is just
search & replace."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: fix type definitions in uapi header
This update adds a debugfs interface to modify a pin configuration
for a given state in the pinctrl map. This allows to modify the
configuration for a non-active state, typically sleep state.
This configuration is not applied right away, but only when the state
will be entered.
This solution is mandated for us by HW validation: in order
to test and verify several pin configurations during sleep without
recompiling the software.
Change log in this patch set;
Take into account latest feedback from Stephen Warren:
- stale comments update
- improved code efficiency and readibility
- limit size of global variable pinconf_dbg_conf
- remove req_type as it can easily be added later when
add/delete requests support is implemented
Signed-off-by: Laurent Meunier <laurent.meunier@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All HCI command send functions that take a pointer to the command
parameters do not need to modify the content in any way (they merely
copy the data to an skb). Therefore, the parameter type should be
declared const. This also allows passing already const parameters to
these APIs which previously would have generated a compiler warning.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
These patches get us closer to adding multiplatform support on
the Exynos platform, they are part of a longer series of
patches. This would get all the simple stuff out of the
way, and I don't think there is a big risk of introducing
regressions with these.
A lot of the other patches have already been merged into
subsystem trees. After this series in in arm-soc, what is
left comes down to
* The ASoC conversion to dmaengine won't make it unless someone
who knows that code better steps up to do it right away. This
means that we won't have audio in a 3.10 multiplatform kernel
on Exynos, but it will still work for users that don't enable
multiplatform.
* The irqchip (combiner), clk and clksource patches are all based
on top of other changesets we pulled in from your trees, so I
would not make them part of the next/multiplatform branch. We can
apply them on top of the next/drivers branch once they are
tested successfully.
* A trivial patch is needed in the end to actually make
CONFIG_ARCH_EXYNOS visible in multiplatform configurations.
We will do that as a separate patch once everything else is
there.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
plat/regs-sdhci.h is not used anywhere but in the sdhci-s3c
driver, so it can become a local file there and all other
inclusions removed.
plat/sdhci.h is used only to define the platform devices,
and with the exception of the platform_data structure not
needed by the driver, so we can split out the platform_data
definition instead and leave the rest to platform code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chris Ball <cjb@laptop.org>
Add code to handle DRAM ECC errors decoding for Fam16h.
Tested on Fam16h with ECC turned on using the mce_amd_inj facility and
works fine.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
[ Boris: cleanups and clarifications ]
Signed-off-by: Borislav Petkov <bp@suse.de>
The current mutex spinning code (with MUTEX_SPIN_ON_OWNER option
turned on) allow multiple tasks to spin on a single mutex
concurrently. A potential problem with the current approach is
that when the mutex becomes available, all the spinning tasks
will try to acquire the mutex more or less simultaneously. As a
result, there will be a lot of cacheline bouncing especially on
systems with a large number of CPUs.
This patch tries to reduce this kind of contention by putting
the mutex spinners into a queue so that only the first one in
the queue will try to acquire the mutex. This will reduce
contention and allow all the tasks to move forward faster.
The queuing of mutex spinners is done using an MCS lock based
implementation which will further reduce contention on the mutex
cacheline than a similar ticket spinlock based implementation.
This patch will add a new field into the mutex data structure
for holding the MCS lock. This expands the mutex size by 8 bytes
for 64-bit system and 4 bytes for 32-bit system. This overhead
will be avoid if the MUTEX_SPIN_ON_OWNER option is turned off.
The following table shows the jobs per minute (JPM) scalability
data on an 8-node 80-core Westmere box with a 3.7.10 kernel. The
numactl command is used to restrict the running of the fserver
workloads to 1/2/4/8 nodes with hyperthreading off.
+-----------------+-----------+-----------+-------------+----------+
| Configuration | Mean JPM | Mean JPM | Mean JPM | % Change |
| | w/o patch | patch 1 | patches 1&2 | 1->1&2 |
+-----------------+------------------------------------------------+
| | User Range 1100 - 2000 |
+-----------------+------------------------------------------------+
| 8 nodes, HT off | 227972 | 227237 | 305043 | +34.2% |
| 4 nodes, HT off | 393503 | 381558 | 394650 | +3.4% |
| 2 nodes, HT off | 334957 | 325240 | 338853 | +4.2% |
| 1 node , HT off | 198141 | 197972 | 198075 | +0.1% |
+-----------------+------------------------------------------------+
| | User Range 200 - 1000 |
+-----------------+------------------------------------------------+
| 8 nodes, HT off | 282325 | 312870 | 332185 | +6.2% |
| 4 nodes, HT off | 390698 | 378279 | 393419 | +4.0% |
| 2 nodes, HT off | 336986 | 326543 | 340260 | +4.2% |
| 1 node , HT off | 197588 | 197622 | 197582 | 0.0% |
+-----------------+-----------+-----------+-------------+----------+
At low user range 10-100, the JPM differences were within +/-1%.
So they are not that interesting.
The fserver workload uses mutex spinning extensively. With just
the mutex change in the first patch, there is no noticeable
change in performance. Rather, there is a slight drop in
performance. This mutex spinning patch more than recovers the
lost performance and show a significant increase of +30% at high
user load with the full 8 nodes. Similar improvements were also
seen in a 3.8 kernel.
The table below shows the %time spent by different kernel
functions as reported by perf when running the fserver workload
at 1500 users with all 8 nodes.
+-----------------------+-----------+---------+-------------+
| Function | % time | % time | % time |
| | w/o patch | patch 1 | patches 1&2 |
+-----------------------+-----------+---------+-------------+
| __read_lock_failed | 34.96% | 34.91% | 29.14% |
| __write_lock_failed | 10.14% | 10.68% | 7.51% |
| mutex_spin_on_owner | 3.62% | 3.42% | 2.33% |
| mspin_lock | N/A | N/A | 9.90% |
| __mutex_lock_slowpath | 1.46% | 0.81% | 0.14% |
| _raw_spin_lock | 2.25% | 2.50% | 1.10% |
+-----------------------+-----------+---------+-------------+
The fserver workload for an 8-node system is dominated by the
contention in the read/write lock. Mutex contention also plays a
role. With the first patch only, mutex contention is down (as
shown by the __mutex_lock_slowpath figure) which help a little
bit. We saw only a few percents improvement with that.
By applying patch 2 as well, the single mutex_spin_on_owner
figure is now split out into an additional mspin_lock figure.
The time increases from 3.42% to 11.23%. It shows a great
reduction in contention among the spinners leading to a 30%
improvement. The time ratio 9.9/2.33=4.3 indicates that there
are on average 4+ spinners waiting in the spin_lock loop for
each spinner in the mutex_spin_on_owner loop. Contention in
other locking functions also go down by quite a lot.
The table below shows the performance change of both patches 1 &
2 over patch 1 alone in other AIM7 workloads (at 8 nodes,
hyperthreading off).
+--------------+---------------+----------------+-----------------+
| Workload | mean % change | mean % change | mean % change |
| | 10-100 users | 200-1000 users | 1100-2000 users |
+--------------+---------------+----------------+-----------------+
| alltests | 0.0% | -0.8% | +0.6% |
| five_sec | -0.3% | +0.8% | +0.8% |
| high_systime | +0.4% | +2.4% | +2.1% |
| new_fserver | +0.1% | +14.1% | +34.2% |
| shared | -0.5% | -0.3% | -0.4% |
| short | -1.7% | -9.8% | -8.3% |
+--------------+---------------+----------------+-----------------+
The short workload is the only one that shows a decline in
performance probably due to the spinner locking and queuing
overhead.
Signed-off-by: Waiman Long <Waiman.Long@hp.com>
Reviewed-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Chandramouleeswaran Aswin <aswin@hp.com>
Cc: Norton Scott J <scott.norton@hp.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Clark Williams <williams@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1366226594-5506-4-git-send-email-Waiman.Long@hp.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We should store file xattrs in struct cfent instead of struct cftype,
because cftype is a type while cfent is object instance of cftype.
For example each cgroup has a tasks file, and each tasks file is
associated with a uniq cfent, but all those files share the same
struct cftype.
Alexey Kodanev reported a crash, which can be reproduced:
# mount -t cgroup -o xattr /sys/fs/cgroup
# mkdir /sys/fs/cgroup/test
# setfattr -n trusted.value -v test_value /sys/fs/cgroup/tasks
# rmdir /sys/fs/cgroup/test
# umount /sys/fs/cgroup
oops!
In this case, simple_xattrs_free() will free the same struct simple_xattrs
twice.
tj: Dropped unused local variable @cft from cgroup_diput().
Cc: <stable@vger.kernel.org> # 3.8.x
Reported-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: Li Zefan <lizefan@huawei.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This commit adds a driver that exposes all the radio related
functionality of the Si476x series of chips via the V4L2 subsystem.
[mchehab@redhat.com: change it to depends on MFD_SI476X_CORE instead of
selecting it; vidioc_s_register now uses const struct]
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Tahvo is a multi-function device on Nokia 770, implementing USB
transceiver and charge/battery control.
It's so close to Retu that a single driver can support both.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Host queues (Qdisc + NIC) can hold packets so long that TCP can
eventually retransmit a packet before the first transmit even left
the host.
Its not clear right now if we could avoid this in the first place :
- We could arm RTO timer not at the time we enqueue packets, but
at the time we TX complete them (tcp_wfree())
- Cancel the sending of the new copy of the packet if prior one
is still in queue.
This patch adds instrumentation so that we can at least see how
often this problem happens.
TCPSpuriousRtxHostQueues SNMP counter is incremented every time
we detect the fast clone is not yet freed in tcp_transmit_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indirect descriptors introduce a new block operation
(BLKIF_OP_INDIRECT) that passes grant references instead of segments
in the request. This grant references are filled with arrays of
blkif_request_segment_aligned, this way we can send more segments in a
request.
The proposed implementation sets the maximum number of indirect grefs
(frames filled with blkif_request_segment_aligned) to 256 in the
backend and 32 in the frontend. The value in the frontend has been
chosen experimentally, and the backend value has been set to a sane
value that allows expanding the maximum number of indirect descriptors
in the frontend if needed.
The migration code has changed from the previous implementation, in
which we simply remapped the segments on the shared ring. Now the
maximum number of segments allowed in a request can change depending
on the backend, so we have to requeue all the requests in the ring and
in the queue and split the bios in them if they are bigger than the
new maximum number of segments.
[v2: Fixed minor comments by Konrad.
[v1: Added padding to make the indirect request 64bit aligned.
Added some BUGs, comments; fixed number of indirect pages in
blkif_get_x86_{32/64}_req. Added description about the indirect operation
in blkif.h]
Signed-off-by: Roger Pau Monné <roger.pau@citrix.com>
[v3: Fixed spaces and tabs mix ups]
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
The Palma device like TPS65913 have the mode mask which is also
used for enable/disable the rails. The mode bits are defined as
00: OFF
01: AUTO
10: ECO
11: Forced PWM
and modes are set accordingly as
REGULATOR_MODE_NORMAL: AUTO
REGULATOR_MODE_IDLE: ECO
REGULATOR_MODE_FAST: PWM
Two issue observed:
1. If client calls following sequence:
regulator_enable(),
regulator_set_mode(FAST),
regulator_disable()
and again the regulator_enable() then the mode is reset
to NORMAL inplace of keeping the mode as FAST.
Fixing this by storing the current mode configured by client
and restoring modes when enable() is called after disable().
2. In following sequence, the regulator get enabled:
regulator_disable()
regulator_set_mode(FAST),
Fixing this by updating new mode in register only if it is
enabled.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently Palma regulator driver support the ramp delay
through rail specific platform data.
As regulator framework support the configuration of ramp
delay through regulator constraint, using the framework
method and removing the platform specific data approach.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This reverts commit 3a366e614d.
Wanlong Gao reports that it causes a kernel panic on his machine several
minutes after boot. Reverting it removes the panic.
Jens says:
"It's not quite clear why that is yet, so I think we should just revert
the commit for 3.9 final (which I'm assuming is pretty close).
The wifi is crap at the LSF hotel, so sending this email instead of
queueing up a revert and pull request."
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Requested-by: Jens Axboe <axboe@kernel.dk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ASoC: More updates for v3.10
The main additional change here is Lars-Peter's DMA work plus the
platform conversions which have been tested - getting this in mainline
will make life easier for development after the merge window. These
factor a large chunk of code out of the drivers for the platforms using
dmaengine, greatly simplifying development.
Use the generic dmaengine PCM driver instead of a custom implemention. There is
a minor functional change, the ux500 PCM driver did not preallocate the audio
buffer, while the generic dmaengine PCM driver will do this.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A lot of regulator hardware has ascendant voltage list.
This patch adds regulator_map_voltage_ascend() and export it.
Drivers that have ascendant voltage list can use this as their map_voltage()
operation, this is more efficient than default regulator_map_voltage_iterate()
function.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds two formats for Direct Stream Digital (DSD), a
pulse-density encoding format which is described here:
https://en.wikipedia.org/wiki/Direct_Stream_Digital
DSD operates on 2.8, 5.6 or 11.2MHz sample rates and as a 1-bit
stream.
The two new types added by this patch describe streams that are capable
of handling DSD samples in DOP format as 8-bit or in 16-bit (or at a x8
or x16 data rate, respectively).
DSD itself specifies samples in *bit*, while DOP and ALSA handle them
as *bytes*. Hence, a factor of 8 or 16 has to be applied for the sample
rare configuration, according to the following table:
configured hardware
176.4KHz 352.8kHz 705.6KHz <---- sample rate
8-bit 2.8MHz 5.6MHz
16-bit 2.8Mhz 5.6MHz 11.2MHz
`-----------------------------'
actual DSD sample rates
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
From Sekhar Nori:
v3.10 board updates for DaVinci
This set of patches enables remoteproc support
on DA850 EVM and fixes some sparse warnings for
the same board.
* tag 'davinci-for-v3.10/board-2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da850 evm: fix const qualifier placement
ARM: davinci: da850 board: add remoteproc support
ARM: davinci: ensure global variables are declared
ARM: davinci: sram.c: fix incorrect type in assignment
ARM: davinci: da8xx dt: make file local symbols static
ARM: davinci: da8xx: add remoteproc support
ARM: davinci: remove test for undefined Kconfig macro
ARM: davinci: mmc: derive version information from device name
ARM: davinci: da850: add ECAP & EHRPWM clock nodes
ARM: davinci: clk framework support for enable/disable functionality
From Sekhar Nori:
v3.10 DT updates for DaVinci
This set of patches adds support for PWMs and SPI
controller present on DA850 and for SPI flash present on
DA850 EVM.
* tag 'davinci-for-v3.10/dt-2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM: davinci: da850: override mmc DT node device name
ARM: davinci: da850: add mmc DT entries
mmc: davinci_mmc: add DT support
ARM: davinci: da850: add tps6507x regulator DT data
ARM: regulator: add tps6507x device tree data
ARM: davinci: remove test for undefined Kconfig macro
ARM: davinci: mmc: derive version information from device name
ARM: davinci: da850: add ECAP & EHRPWM clock nodes
ARM: davinci: clk framework support for enable/disable functionality
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper:
mvebu dt for v3.10 round 4
- mvebu LPAE 64bit dts file changes
* tag 'dt-3.10-4' of git://git.infradead.org/users/jcooper/linux: (52 commits)
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
arm: mvebu: PCIe Device Tree informations for Armada XP GP
arm: mvebu: PCIe Device Tree informations for Armada 370 DB
arm: mvebu: PCIe Device Tree informations for Armada 370 Mirabox
arm: mvebu: PCIe Device Tree informations for Armada XP DB
arm: mvebu: PCIe Device Tree informations for OpenBlocks AX3-4
arm: mvebu: add PCIe Device Tree informations for Armada XP
arm: mvebu: add PCIe Device Tree informations for Armada 370
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
...
Signed-off-by: Olof Johansson <olof@lixom.net>
From Jason Cooper:
mvebu soc changes for v3.10
- use the mvebu-mbus driver
- prep for LPAE support
Depends:
- mvebu/cleanup (tags/cleanup_for_v3.10)
- mvebu/drivers (tags/drivers_for_v3.10)
* tag 'soc_for_v3.10' of git://git.infradead.org/users/jcooper/linux:
ARM: mvebu: Align the internal registers virtual base to support LPAE
ARM: mvebu: Limit the DMA zone when LPAE is selected
arm: plat-orion: remove addr-map code
arm: mach-mv78xx0: convert to use the mvebu-mbus driver
arm: mach-orion5x: convert to use mvebu-mbus driver
arm: mach-dove: convert to use mvebu-mbus driver
arm: mach-kirkwood: convert to use mvebu-mbus driver
arm: mach-mvebu: convert to use mvebu-mbus driver
bus: mvebu: fix mistake in PCIe window target attribute for Kirkwood
bus: mvebu-mbus: Restore checking for coherency fabric hardware
ARM: Orion: add dbg_show function to gpio-orion driver
bus: introduce an Marvell EBU MBus driver
arm: mach-orion5x: use mv_mbus_dram_info() in PCI code
arm: plat-orion: use mv_mbus_dram_info() in PCIe code
arm: plat-orion: only build addr-map.c when needed
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch renames LE_SCANNING_ENABLED and LE_SCANNING_DISABLED
macros to LE_SCAN_ENABLE and LE_SCAN_DISABLE in order to keep
the same prefix others LE scan macros have.
It also fixes le_scan_enable_req function so it uses the LE_SCAN_
ENABLE macro instead of a magic number.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds macros for filter_duplicates parameter values from
HCI LE Set Scan Enable command. It also fixes le_scan_enable_req
function so it uses the LE_SCAN_FILTER_DUP_ENABLE macro instead of
a magic number.
The LE_SCAN_FILTER_DUP_DISABLE was also defined since it will be
required to properly support the GAP Observer Role.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch adds macros for active and passive LE scan type values.
The LE_SCAN_PASSIVE was also defined since it will be used in future
by LE connection routine and GAP Observer Role support.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
With the introduction of CSA4 there is now also a features page number 2
available. This patch increments the maximum supported page number to 2
and adds code for reading all available pages (as long as we have
support for them - indicated by HCI_MAX_PAGES).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The local and remote features are organized by page number. Page 0
are the LMP features, page 1 the host features, and any pages beyond 1
features that future core specification versions may define. So far
we've only had the first two pages and two separate variables has been
convenient enough, however with the introduction of Core Specification
Addendum 4 there are features defined on page 2.
Instead of requiring the addition of a new variable each time a new page
number is defined, this patch refactors the code to use a single table
for the features. The patch needs to update both the hci_dev and
hci_conn structures since there are macros that depend on the features
being represented in the same way in both of them.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Allow intel_idle and cpuidle to utilize C8, C9, C10
when they are present on...
"Fourth Generation Intel(R) Core(TM) Processors",
which are based on Intel(R) microarchitecture code name Haswell.
Signed-off-by: Len Brown <len.brown@intel.com>
Vivek found old kexec-tools does not work new kernel anymore.
So change back crashkernel= back to old behavoir, and add crashkernel_high=
to let user decide if buffer could be above 4G, and also new kexec-tools will
be needed.
-v2: let crashkernel=X override crashkernel_high=
update description about _high will be ignored by crashkernel=X
-v3: update description about kernel-parameters.txt according to Vivek.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1366089828-19692-4-git-send-email-yinghai@kernel.org
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Chao said that kdump does does work well on his system on 3.8
without extra parameter, even iommu does not work with kdump.
And now have to append crashkernel_low=Y in first kernel to make
kdump work.
We have now modified crashkernel=X to allocate memory beyong 4G (if
available) and do not allocate low range for crashkernel if the user
does not specify that with crashkernel_low=Y. This causes regression
if iommu is not enabled. Without iommu, swiotlb needs to be setup in
first 4G and there is no low memory available to second kernel.
Set crashkernel_low automatically if the user does not specify that.
For system that does support IOMMU with kdump properly, user could
specify crashkernel_low=0 to save that 72M low ram.
-v3: add swiotlb_size() according to Konrad.
-v4: add comments what 8M is for according to hpa.
also update more crashkernel_low= in kernel-parameters.txt
-v5: update changelog according to Vivek.
-v6: Change description about swiotlb referring according to HATAYAMA.
Reported-by: WANG Chao <chaowang@redhat.com>
Tested-by: WANG Chao <chaowang@redhat.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1366089828-19692-2-git-send-email-yinghai@kernel.org
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Currently kernel generates IDs for posix timers in a global manner --
there's a kernel-wide IDR tree from which IDs are created. This makes
it impossible to recreate a timer with a desired ID (in particular
this is done by the CRIU checkpoint-restore project) -- since these
IDs are global it may happen, that at the time we recreate a timer, the
ID we want for it is already busy by some other timer.
In order to address this, replace the IDR tree with a global hash
table for timers and makes timer IDs unique per signal_struct (to
which timers are linked anyway). With this, two timers belonging to
different processes may have equal IDs and we can recreate either of
them with the ID we want.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Matthew Helsley <matt.helsley@gmail.com>
Link: http://lkml.kernel.org/r/513D9FF5.9010004@parallels.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The structure sctp_ulpq is embedded into sctp_association and never
separately allocated, also ulpq->malloced is always 0, so that
kfree() is never called. Therefore, remove this code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sctp_bind_addr structure has a 'malloced' member that is
always set to 0, thus in sctp_bind_addr_free() the kfree()
part can never be called. This part is embedded into
sctp_ep_common anyway and never alloced.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_transport's member 'malloced' is set to 1, never evaluated
and the structure is kfreed anyway. So just remove it.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_outq is embedded into sctp_association, and thus never
kmalloced in any way. Also, malloced is always 0, thus kfree()
is never called. Therefore, remove that dead piece of code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_inq is never kmalloced, since it's integrated into sctp_ep_common
and only initialized from eps and assocs. Therefore, remove the dead
code from there.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sctp_ssnmap_init() can only be called from sctp_ssnmap_new()
where malloced is always set to 1. Thus, when we call
sctp_ssnmap_free() the test for map->malloced evaluates always
to true.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesse Gross says:
====================
A number of improvements for net-next/3.10.
Highlights include:
* Properly exposing linux/openvswitch.h to userspace after the uapi
changes.
* Simplification of locking. It immediately makes things simpler to
reason about and avoids holding RTNL mutex for longer than
necessary. In the near future it will also enable tunnel
registration and more fine-grained locking.
* Miscellaneous cleanups and simplifications.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
