This patch removes init_enable option from pdata, the init_enable
was intended that the device should start streaming video immediately
but ideally the bridge drivers should call s_stream explicitly for such
devices to start video.
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A complete refurbished series inclunding:
- DT support for the MFD, TSC and ADC driver & platform device support,
which has no users, has been killed.
- iio_map from last series is gone and replaced by proper nodes in the
device tree.
- suspend fixes which means correct data structs are taken and no
interrupt storm
- fifo split which should problem with TSC & ADC beeing used at the same
time
- The ADC channels are now checked before blindly applied. That means the
touch part reads X, Y and Z coordinates and does not mix them up. Same
goes for the IIO ADC driver.
- The IIO ADC driver now creates files named in_voltageX_raw where X
represents the ADC line instead of a number starting at 0. A read from
this file can return -EBUSY in case touch is busy and the ADC didn't
collect a value.
If CONFIG_NET_NS is not set then __net_init is the same as __init and
__net_exit is the same as __exit. These functions will be removed from
memory after the module loads or is removed. Functions that are exported
for use by other functions should never be labeled for removal.
Bug introduced by commit c544193214
("GRE: Refactor GRE tunneling code.")
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Track the AP's beacon rate in the scan BSS data and in the
interface configuration to let the drivers know which rate
the AP is using. This information may be used by drivers,
in our case to let the firmware optimise beacon RX.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Linux sends new unset data during disorder and recovery state if all
(suspected) lost packets have been retransmitted ( RFC5681, section
3.2 step 1 & 2, RFC3517 section 4, NexSeg() Rule 2). One requirement
is to keep the receive window about twice the estimated sender's
congestion window (tcp_rcv_space_adjust()), assuming the fast
retransmits repair the losses in the next round trip.
But currently it's not the case on the first round trip in either
normal or Fast Open connection, beucase the initial receive window
is identical to (expected) sender's initial congestion window. The
fix is to double it.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mfd: arizona: Updates for v3.10
A bunch of enhancements and fixes for the arizona devices, adding a few
new features (the main one being device tree) and improving robustness.
* s/percpu_ref_release/percpu_ref_func_t/ as it's customary to have _t
postfix for types and the type is gonna be used for a different type
of callback too.
* Add @ARG to function comments.
* Drop unnecessary and unaligned indentation from percpu_ref_init()
function comment.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Kent Overstreet <koverstreet@google.com>
percpu_ref_get/put() are using preempt_disable/enable() while
percpu_ref_kill() is using plain call_rcu() instead of
call_rcu_sched(). This is buggy as grace periods of the two may not
match. Fix it by using plain RCU in percpu_ref_get/put().
(I suggested using sched RCU in the first place but there's no actual
benefit in doing so unless we're gonna introduce different variants
of get/put to be called while preemption is alredy disabled, which we
definitely shouldn't.)
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Kent Overstreet <koverstreet@google.com>
Since the jbd_debug() is implemented with two separate printk()
calls, it can lead to corrupted and misleading debug output like
the following (see lines marked with "*"):
[ 290.339362] (fs/jbd2/journal.c, 203): kjournald2: kjournald2 wakes
[ 290.339365] (fs/jbd2/journal.c, 155): kjournald2: commit_sequence=42103, commit_request=42104
[ 290.339369] (fs/jbd2/journal.c, 158): kjournald2: OK, requests differ
[* 290.339376] (fs/jbd2/journal.c, 648): jbd2_log_wait_commit:
[* 290.339379] (fs/jbd2/commit.c, 370): jbd2_journal_commit_transaction: JBD2: want 42104, j_commit_sequence=42103
[* 290.339382] JBD2: starting commit of transaction 42104
[ 290.339410] (fs/jbd2/revoke.c, 566): jbd2_journal_write_revoke_records: Wrote 0 revoke records
[ 290.376555] (fs/jbd2/commit.c, 1088): jbd2_journal_commit_transaction: JBD2: commit 42104 complete, head 42079
i.e. the debug output from log_wait_commit and journal_commit_transaction
have become interleaved. The output should have been:
(fs/jbd2/journal.c, 648): jbd2_log_wait_commit: JBD2: want 42104, j_commit_sequence=42103
(fs/jbd2/commit.c, 370): jbd2_journal_commit_transaction: JBD2: starting commit of transaction 42104
It is expected that this is not easy to replicate -- I was only able
to cause it on preempt-rt kernels, and even then only under heavy
I/O load.
Reported-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Suggested-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The bit_spinlock functions are only used for the jbd_lock_bh_state
functions (and friends) in jbd_common.h and are not directly used
by either of jbd.h or jbd2.h content.
The jbd_common file is new as of commit 446066724c ("jdb/jbd2: factor
out common functions from the jbd[2] header files") but common
(and isolated) headers were not considered for factoring at that time.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Inode's data or non journaled quota may be written w/o jounral so we
_must_ send a barrier at the end of ext4_sync_fs. But it can be
skipped if journal commit will do it for us.
Also fix data integrity for nojournal mode.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Current implementation of jbd2_journal_force_commit() is suboptimal because
result in empty and useless commits. But callers just want to force and wait
any unfinished commits. We already have jbd2_journal_force_commit_nested()
which does exactly what we want, except we are guaranteed that we do not hold
journal transaction open.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Currently the media device link_notify callback is invoked before the
actual change of state of a link when the link is being enabled, and
after the actual change of state when the link is being disabled.
This doesn't allow a media device driver to perform any operations
on a full graph before a link is disabled, as well as performing
any tasks on a modified graph right after a link's state is changed.
This patch modifies signature of the link_notify callback. This
callback is now called always before and after a link's state change.
To distinguish the notifications a 'notification' argument is added
to the link_notify callback: MEDIA_DEV_NOTIFY_PRE_LINK_CH indicates
notification before link's state change and
MEDIA_DEV_NOTIFY_POST_LINK_CH corresponds to a notification after
link flags change.
[mchehab@redhat.com: whitespace cleanups]
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This enumeration is now private to exynos4-is and the exynos5 camera
subsystem driver may have the subdevs handling designed differently.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch introduces common structure for the video entities
to handle all video nodes and media pipelines associated with
them in more generic way.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Pull networking update from David Miller:
1) Fix dump iterator in nfnl_acct_dump() and ctnl_timeout_dump() to
dump all objects properly, from Pablo Neira Ayuso.
2) xt_TCPMSS must use the default MSS of 536 when no MSS TCP option is
present. Fix from Phil Oester.
3) qdisc_get_rtab() looks for an existing matching rate table and uses
that instead of creating a new one. However, it's key matching is
incomplete, it fails to check to make sure the ->data[] array is
identical too. Fix from Eric Dumazet.
4) ip_vs_dest_entry isn't fully initialized before copying back to
userspace, fix from Dan Carpenter.
5) Fix ubuf reference counting regression in vhost_net, from Jason
Wang.
6) When sock_diag dumps a socket filter back to userspace, we have to
translate it out of the kernel's internal representation first.
From Nicolas Dichtel.
7) davinci_mdio holds a spinlock while calling pm_runtime, which
sleeps. Fix from Sebastian Siewior.
8) Timeout check in sh_eth_check_reset is off by one, from Sergei
Shtylyov.
9) If sctp socket init fails, we can NULL deref during cleanup. Fix
from Daniel Borkmann.
10) netlink_mmap() does not propagate errors properly, from Patrick
McHardy.
11) Disable powersave and use minstrel by default in ath9k. From Sujith
Manoharan.
12) Fix a regression in that SOCK_ZEROCOPY is not set on tuntap sockets
which prevents vhost from being able to use zerocopy. From Jason
Wang.
13) Fix race between port lookup and TX path in team driver, from Jiri
Pirko.
14) Missing length checks in bluetooth L2CAP packet parsing, from Johan
Hedberg.
15) rtlwifi fails to connect to networking using any encryption method
other than WPA2. Fix from Larry Finger.
16) Fix iwlegacy build due to incorrect CONFIG_* ifdeffing for power
management stuff. From Yijing Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
b43: stop format string leaking into error msgs
ath9k: Use minstrel rate control by default
Revert "ath9k_hw: Update rx gain initval to improve rx sensitivity"
ath9k: Disable PowerSave by default
net: wireless: iwlegacy: fix build error for il_pm_ops
rtlwifi: Fix a false leak indication for PCI devices
wl12xx/wl18xx: scan all 5ghz channels
wl12xx: increase minimum singlerole firmware version required
wl12xx: fix minimum required firmware version for wl127x multirole
rtlwifi: rtl8192cu: Fix problem in connecting to WEP or WPA(1) networks
mwifiex: debugfs: Fix out of bounds array access
Bluetooth: Fix mgmt handling of power on failures
Bluetooth: Fix missing length checks for L2CAP signalling PDUs
Bluetooth: btmrvl: support Marvell Bluetooth device SD8897
Bluetooth: Fix checks for LE support on LE-only controllers
team: fix checks in team_get_first_port_txable_rcu()
team: move add to port list before port enablement
team: check return value of team_get_port_by_index_rcu() for NULL
tuntap: set SOCK_ZEROCOPY flag during open
netlink: fix error propagation in netlink_mmap()
...
From Kukjin Kim, driver updats for s3c24xx:
- move cpufreq driver into drivers/
- add pinctrl-s3c24xx driver
- cleanup OF in gpio driver
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull block layer fixes from Jens Axboe:
"Outside of bcache (which really isn't super big), these are all
few-liners. There are a few important fixes in here:
- Fix blk pm sleeping when holding the queue lock
- A small collection of bcache fixes that have been done and tested
since bcache was included in this merge window.
- A fix for a raid5 regression introduced with the bio changes.
- Two important fixes for mtip32xx, fixing an oops and potential data
corruption (or hang) due to wrong bio iteration on stacked devices."
* 'for-linus' of git://git.kernel.dk/linux-block:
scatterlist: sg_set_buf() argument must be in linear mapping
raid5: Initialize bi_vcnt
pktcdvd: silence static checker warning
block: remove refs to XD disks from documentation
blkpm: avoid sleep when holding queue lock
mtip32xx: Correctly handle bio->bi_idx != 0 conditions
mtip32xx: Fix NULL pointer dereference during module unload
bcache: Fix error handling in init code
bcache: clarify free/available/unused space
bcache: drop "select CLOSURES"
bcache: Fix incompatible pointer type warning
There is div64_long() to handle the s64/long division, but no mocro do
u64/ul division. It is necessary in some scenarios, so add this
function.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Alex Shi <alex.shi@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When we have a page fault for the address which is backed by a hugepage
under migration, the kernel can't wait correctly and do busy looping on
hugepage fault until the migration finishes. As a result, users who try
to kick hugepage migration (via soft offlining, for example) occasionally
experience long delay or soft lockup.
This is because pte_offset_map_lock() can't get a correct migration entry
or a correct page table lock for hugepage. This patch introduces
migration_entry_wait_huge() to solve this.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Reviewed-by: Rik van Riel <riel@redhat.com>
Reviewed-by: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: <stable@vger.kernel.org> [2.6.35+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The dmesg_restrict sysctl currently covers the syslog method for access
dmesg, however /dev/kmsg isn't covered by the same protections. Most
people haven't noticed because util-linux dmesg(1) defaults to using the
syslog method for access in older versions. With util-linux dmesg(1)
defaults to reading directly from /dev/kmsg.
To fix /dev/kmsg, let's compare the existing interfaces and what they
allow:
- /proc/kmsg allows:
- open (SYSLOG_ACTION_OPEN) if CAP_SYSLOG since it uses a destructive
single-reader interface (SYSLOG_ACTION_READ).
- everything, after an open.
- syslog syscall allows:
- anything, if CAP_SYSLOG.
- SYSLOG_ACTION_READ_ALL and SYSLOG_ACTION_SIZE_BUFFER, if
dmesg_restrict==0.
- nothing else (EPERM).
The use-cases were:
- dmesg(1) needs to do non-destructive SYSLOG_ACTION_READ_ALLs.
- sysklog(1) needs to open /proc/kmsg, drop privs, and still issue the
destructive SYSLOG_ACTION_READs.
AIUI, dmesg(1) is moving to /dev/kmsg, and systemd-journald doesn't
clear the ring buffer.
Based on the comments in devkmsg_llseek, it sounds like actions besides
reading aren't going to be supported by /dev/kmsg (i.e.
SYSLOG_ACTION_CLEAR), so we have a strict subset of the non-destructive
syslog syscall actions.
To this end, move the check as Josh had done, but also rename the
constants to reflect their new uses (SYSLOG_FROM_CALL becomes
SYSLOG_FROM_READER, and SYSLOG_FROM_FILE becomes SYSLOG_FROM_PROC).
SYSLOG_FROM_READER allows non-destructive actions, and SYSLOG_FROM_PROC
allows destructive actions after a capabilities-constrained
SYSLOG_ACTION_OPEN check.
- /dev/kmsg allows:
- open if CAP_SYSLOG or dmesg_restrict==0
- reading/polling, after open
Addresses https://bugzilla.redhat.com/show_bug.cgi?id=903192
[akpm@linux-foundation.org: use pr_warn_once()]
Signed-off-by: Kees Cook <keescook@chromium.org>
Reported-by: Christian Kujau <lists@nerdbynature.de>
Tested-by: Josh Boyer <jwboyer@redhat.com>
Cc: Kay Sievers <kay@vrfy.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The TUN_PERSIST flag is not reported at all -- both TUNGETIFF, and sysfs
"flags" attribute skip one. Knowing whether a device is persistent or not
is critical for checkpoint-restore, thus I propose to add the read-only
IFF_PERSIST one for this.
Setting this new IFF_PERSIST is hardly possible, as TUNSETIFF doesn't check
for unknown flags being zero and thus there can be trash.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Felipe writes:
usb: patches for v3.11 merge window
All function drivers are now converted to our new configfs-based
binding. Eventually this will help us getting rid of in-kernel
gadget drivers and only keep function drivers in the kernel.
MUSB was taught that it needs to be built for host-only and
device-only modes too. We had this support long ago but it
involved a ridiculous amount of ifdefs. Now we have a much
cleaner approach.
Samsung Exynos4 platform now implements HSIC support.
We're introducing support for AB8540 and AB9540 PHYs.
MUSB module reinsertion now works as expected, before we were
getting -EBUSY being returned by the resource checks done on
driver core.
DWC3 now has minimum support for TI's AM437x series of SoCs.
OMAP5 USB3 PHY learned one extra DPLL configuration values because
that PHY is reused in TI's DRA7xx devices.
We're introducing support for Faraday fotg210 UDCs.
Last, but not least, the usual set of non-critical fixes and cleanups
ranging from usage of platform_{get,set}_drvdata to lock improvements.
Signed-of-by: Felipe Balbi <balbi@ti.com>
John W. Linville says:
====================
This pull request is intended for the 3.11 stream...
One big highlight is the cw1200 driver the ST-E CW1100 & CW1200
WLAN chipsets. This one has been lingering for a while, lacking
some review comments. Once started getting pulled into linux-next,
it got a bit more attention and a number of improvements were made
over the initial cut. No doubt there will be more changes ahead,
but I think it is looking alright at this point.
Along with that, there is the usual flurry of updates to the mac80211
core and the iwlwifi, mwifiex, ath9k, rt2x00, wil6210, and other
drivers. A few of the highlights are some rt2x00 refactoring/cleanup
by Gabor Juhos, some rt2800 hardware support enhancements by Stanislaw
Gruszka, some iwlwifi power management updates from Alexander Bondar,
some enhanced bcma SPROM support from Rafał Miłecki, and a variety
of other things here and there.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing about the sched_clock implementation in the ARM port is
specific to the architecture. Generalize the code so that other
architectures can use it by selecting GENERIC_SCHED_CLOCK.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
[jstultz: Merge minor collisions with other patches in my tree]
Signed-off-by: John Stultz <john.stultz@linaro.org>
From Heiko Stuebner, enhancements for dw_apb_timer:
- use DECLARE_CLOCKSOURCE_OF and convert its users
- handle the sptimer not being present as sched_clock
- add optional handling of timer clocks
* tag 'dw_apb_timer_of' of git://github.com/mmind/linux-rockchip:
clocksource: dw_apb_timer_of: use clocksource_of_init
clocksource: dw_apb_timer_of: select DW_APB_TIMER
clocksource: dw_apb_timer_of: add clock-handling
clocksource: dw_apb_timer_of: enable the use the clocksource as sched clock
The driver programs a threshold of "coordinate_readouts" say 5. The
REG_FIFO0THR registers says it should it be programmed to "threshold
minus one". The driver does not expect just 5 coordinates but 5 * 2 + 2.
Multiplied by two because 5 for X and 5 for Y and plus 2 because we have
two Z.
The whole thing kind of works because It reads the 5 coordinates for X
and Y from FIFO0 and FIFO1 and the last element in each FIFO is ignored
within the loop and read later.
Nothing guaranties that FIFO1 is ready by the time it is read. In fact I
could see that that FIFO1 reaturns for Y channels 8,9, 10, 12, 6 and for
Y channel 7 for Z. The problem is that channel 7 and channel 12 got
somehow mixed up.
The other Problem is that FIFO1 is also used by the IIO part leading to
wrong results if both (tsc & adc) are used.
The patch tries to clean up the whole thing a little:
- Remove the +1 and -1 in REG_STEPCONFIG, REG_STEPDELAY and its counter
part in the for loop. This is just confusing.
- Use only FIFO0 in TSC. The fifo has space for 64 entries so should be
fine.
- Read the whole FIFO in one function and check the channel.
- in case we dawdle around, make sure we only read a multiple of our
coordinate set. On the second interrupt we will cleanup the remaining
enties.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The two header files removed here are unused and have no users as this
platform was never used with platform devices.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The current driver expected touchscreen input
wires(XP,XN,YP,YN) to be connected in a particular order.
Making changes to accept this as platform data.
Sebastian reworked the original patch and removed a lot of the not
required pieces.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Current code has hard coded value written to
step enable bits. Now the bits are updated based
on how many steps are needed to be configured got
from platform data.
The user needs to take care not to exceed
the count more than 16. While using ADC and TSC
one should take care to set this parameter correctly.
Sebastian added the common lock and moved the code, that manipulates the
steps, from into the mfd module.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The mfd driver creates platform data for the child devices and it is the
ti_tscadc_dev struct. This struct is copied for the two devices.
The copy of the structure makes a common lock in this structure a little
less usefull. Therefore the platform data is not a pointer to the
structure and the same structure is used.
While doing the change I noticed that the suspend/resume code assumes
the wrong pointer for ti_tscadc_dev and this has been fixed as well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Wire the init of a 32bit vcpu by allowing 32bit modes in pstate,
and providing sensible defaults out of reset state.
This feature is of course conditioned by the presence of 32bit
capability on the physical CPU, and is checked by the KVM_CAP_ARM_EL1_32BIT
capability.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
It is common to access regmap registers at bit level, using
regmap_update_bits or regmap_read functions, however the end user has to
take care of a mask or shifting. This becomes overhead when such use
cases are high. Having a common function to do this is much convenient
and less error prone.
The idea of regmap_field is simple, regmap_field gives a logical
structure to bits of the regmap register, and the driver can use this
logical entity without the knowledge of the bit positions and masks all
over the code. This way code looks much neat and it need not handle the
masks, shifts every time it access the those entities.
With this new regmap_field_read/write apis the end user can setup a
regmap field using regmap_field_init and use the return regmap_field to
read write the register field without worrying about the masks or
shifts.
Also this apis will be useful for drivers which are based on regmaps,
like some clocks or pinctrls which can work on the regmap_fields
directly without having to worry about bit positions.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduce Xen support to ARM64
* tag 'xen-arm64-3.1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/sstabellini/xen:
MAINTAINERS: add myself as arm64/xen maintainer
arm64/xen: introduce CONFIG_XEN and hypercall.S on ARM64
arm64/xen: use XEN_IO_PROTO_ABI_ARM on ARM64
arm64/xen: implement ioremap_cached on arm64
arm64/xen: introduce asm/xen header files on arm64
arm/xen: define xen_remap as ioremap_cached
If hci_dev_open fails we need to ensure that the corresponding
mgmt_set_powered command gets an appropriate response. This patch fixes
the missing response by adding a new mgmt_set_powered_failed function
that's used to indicate a power on failure to mgmt. Since a situation
with the device being rfkilled may require special handling in user
space the patch uses a new dedicated mgmt status code for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Cc: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
dw_apb_timer_init used to search the devicetree for matching timer
devices, making calls to it from board files necessary.
Change the dw_apb_timer_init to work with CLOCKSOURCE_OF_DECLARE.
With this change the function gets called once for each timer node
and tracks these number of calls to attach clockevent and clocksource
devices to the nodes.
Also remove the calls to dw_apb_timer_init from all previous users, as
clocksource_of_init is the default for init_time now.
Tested on the upcoming rk3066 code.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
CONFIG_OF_DEVICE is always selected when CONFIG_OF is enabled, so remove
it and simplify of_platform.h and of_device.h headers. This also fixes
!OF compiles using of_platform_populate.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
