Some platforms need the pendown GPIO debounce time setting programmed.
Since the pendown GPIO is handled by the driver, the debounce time
should also be handled along with the pendown GPIO request.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Also the driver was modifued to take advantage of recent improvements in
matrix_keypad_build_keymap() implementation, which automatically allocates
memory for keymap.
The driver was tested on AM335x EVM.
Signed-off-by: AnilKumar Ch <anilkumar@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently da9062_tsi does not probe and it fails as follows:
da9052 1-0048: Unable to determine device interrupts
Use the new da9052 irq functions and allow the driver to probe and operate
correctly.
Tested on mx53qsb board using 'evtest' tool.
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: <linux-input@vger.kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
When doing conversion to dynamic input numbers I inadvertently moved
/dev/input/mice from c,13,63 to c,13,31. We need to fix this so that
setups with statically populated /dev continue working.
Tested-by: Krzysztof Mazur <krzysiek@podlesie.net>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch extracts the test (slot->frame == mt->frame) so that it can
be used in third party drivers.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
In device tree enabled setups requiring preallocated memory for storing keymap
is quite often awkward, so let's provide an option of allocating it directly
in matrix_keypad_build_keymap().
Reviewed-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This goto is only used to skip the next instruction, which can easily be done
without a goto.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes new kernel-doc warning in input-mt.c:
Warning(drivers/input/input-mt.c:38): No description found for parameter
'flags'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch frees stmpe-ts driver from burden of freeing resources :)
devm_* derivatives of multiple routines are used while allocating resources,
which would be freed automatically by kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch frees stmpe-keyboard driver from burden of freeing resources :)
devm_* derivatives of multiple routines are used while allocating resources,
which would be freed automatically by kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch frees spear-keyboard driver from burden of freeing resources :)
devm_* derivatives of multiple routines are used while allocating resources,
which would be freed automatically by kernel.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch handles the fix for unbalanced irq for the cases when
enable_irq_wake fails, and a warning related to same is displayed
on the console. The workaround is handled at the driver level.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously this clock was handled internally by the clockdriver,
but now this is separate clk. So we need take care of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is a demand from driver's writers to use managed devices framework
for their drivers. Unfortunately up to this moment input devices did not
provide support for managed devices and that lead to mixing two styles
of resource management which usually introduced more bugs, such as
manually unregistering input device but relying in devres to free
interrupt handler which (unless device is properly shut off) can cause
ISR to reference already freed memory.
This change introduces devm_input_allocate_device() that will allocate
managed instance of input device so that driver writers who prefer
using devm_* framework do not have to mix 2 styles.
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Reviewed-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
From Linus Walleij:
This patchset will:
- Move all remaining headers out of arch/arm/plat-nomadik/include/plat
out to e.g. include/linux/platform_data
- Delete arch/arm/plat-nomadik
- Convert Nomadik and Ux500 to SPARSE_IRQ
* tag 'kill-plat-sparse-irq' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
ARM: plat-nomadik: convert platforms to SPARSE_IRQ
mfd/db8500-prcmu: use the irq_domain_add_simple()
mfd/ab8500-core: use irq_domain_add_simple()
ARM: plat-nomadik: move MTU, kill plat-nomadik
ARM: plat-nomadik: move DMA40 header to <linux/platform_data>
ARM: plat-nomadik: use DIV_ROUND_CLOSEST()
ARM: plat-nomadik: pass IRQ to timer driver
clk/ux500: explicitly include register header
pinctrl/nomadik: merge old pincfg header
pinctrl/nomadik: move the platform data header
ARM: plat-nomadik: move NMK_GPIO_PER_CHIP into gpio-nomadik.h
ARM: plat-nomadik: Introduce new DB8540 GPIO registers
This patch converts touchscreen into a MFD client.
All the register definitions, clock initialization,
etc has been moved to MFD core driver.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make way for addition of MFD driver.
The existing touchsreen driver is a MFD client.
For better readability we rename the file to
indicate its functionality as only touchscreen.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The touchscreen IP uses level sensitive interrupts rather
than edge sensitive interrupts and therefore the is no need
to use the EOI register to have the module re-strobe the
interrupt line if there pending interrupts exist.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Code currently uses FIFO1 threshold interrupt.
since this is a MFD, Dedicating FIFO0 to touchscreen
and making way for other devices to use FIFO1 as well.
The FIFO can be shared between 2 devices but since the
interrupt used is threshold interrupt on FIFO1, we would
end up having wrong interrupts. Hence changing the same.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
There are 16 programmable Step Configuration
registers which are used by the sequencer.
Program the Steps in order to configure a channel
input to be sampled. If the same step is applied
several times, the coordinate values read are more
accurate.
Hence we provide the user an option of how many steps
should be configured.
For ex: If this value is assigned as 4, This means that
4 steps are applied to read x co-ordinate and 4 steps to read
y co-ordinate. Furtheron the interrupt handler already
holds code to use delta filter and report the best value
out of these values to the input sub-system.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch cleans up the wrong register definitions
and usage for touchscreen controller.
Bit masks were not defined earlier.
For ex: consider a register define as:
write(xyz, ABC)
ABC is expected to be written to register bits 0-11.
Here we see that value written is as expected, but this write
is also affecting all the remaining bits of xyz.
The remaining bits hold the default value as 0 and the write
also sets it to zero. Hence wrong usage were not causing user
visible bugs.
Due to these reasons it was difficult to follow when
compared with TRM.
Unused definitions are also removed.
Since there is change in some naming convention because of
all the above mentioned reasons, the same has been
updated throughout the code.
Bit declarations are grouped to increase readability.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This moves the MTU timer driver from arch/arm/plat-nomadik
to drivers/clocksource and moves the header file to the
platform_data directory.
As this moves the last file being compiled to an object out
of arch/arm/plat-nomadik, we have to "turn off the light"
and delete the plat-nomadik directory, because it is not
allowed to have an empty Makefile in a plat-* directory.
This is probably also a desired side effect of depopulating
the arch/arm directory of drivers. Luckily we have just
deleted all the <plat/*> include files prior to this so
by moving the last one we may delete the directory.
After this all the Ux500 and Nomadik device drivers live
outside of the arch/arm hierarchy.
Cc: Alessandro Rubini <rubini@unipv.it>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull Xen bugfixes from Konrad Rzeszutek Wilk:
- Use appropriate macros instead of hand-rolling our own (ARM).
- Fixes if FB/KBD closed unexpectedly.
- Fix memory leak in /dev/gntdev ioctl calls.
- Fix overflow check in xenbus_file_write.
- Document cleanup.
- Performance optimization when migrating guests.
* tag 'stable/for-linus-3.7-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/mmu: Use Xen specific TLB flush instead of the generic one.
xen/arm: use the __HVC macro
xen/xenbus: fix overflow check in xenbus_file_write()
xen-kbdfront: handle backend CLOSED without CLOSING
xen-fbfront: handle backend CLOSED without CLOSING
xen/gntdev: don't leak memory from IOCTL_GNTDEV_MAP_GRANT_REF
x86: remove obsolete comment from asm/xen/hypervisor.h
Pull HID updates from Jiri Kosina:
"This contains fixes for two devices by Jiri Slaby and Xianhan Yu, new
device IDs for MacBook Pro 10,2 from Dirk Hohndel and generic
multitouch code fix from Alan Cox."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: Add support for the MacBook Pro 10,2 keyboard / touchpad
HID: multitouch: fix maxcontacts problem on GeneralTouch
HID: multitouch: put the case in the right switch statement
HID: microsoft: fix invalid rdesc for 3k kbd
This enables the existing drivers for keyboard and touchpad with the new
USB IDs found on the MBP 13" Reasonable Resolution (also known as the
Retina Display).
Added entries to both keyboard and mouse ignore lists.
Signed-off-by: Dirk Hohndel <dirk@hohndel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The tsc40 driver announces it supports the pressure event, but will never
send one. The announcement will cause tslib to wait for such events and
sending all touch events with a pressure of 0. Removing the announcement
will make tslib fall back to emulating the pressure on touch events so
everything works as expected.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Backend drivers shouldn't transistion to CLOSED unless the frontend is
CLOSED. If a backend does transition to CLOSED too soon then the
frontend may not see the CLOSING state and will not properly shutdown.
So, treat an unexpected backend CLOSED state the same as CLOSING.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
This is the ONKEY driver of the Dialog DA9055 PMIC and depends on the
DA9055 MFD core driver.
This driver was functionally tested on SMDK6410 board.
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds a "select" dependency of KEYBOARD_LPC32XX on INPUT_MATRIXKMAP,
as the other drivers are doing in this regard. This fixes the following
compile error if KEYBOARD_LPC32XX is enabled but INPUT_MATRIXKMAP is not:
drivers/input/keyboard/lpc32xx-keys.c:230: undefined reference to
`matrix_keypad_build_keymap'
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Like our other pen-and-touch products, the Cintiq 24HD touch needs data
to be shared between its two sensors to facilitate proximity-based palm
rejection.
Unlike other tablets that report sensor data through separate interfaces
of the same USB device, the Cintiq 24HD touch has separate USB devices
that are connected to an internal USB hub.
This patch makes it possible to designate the USB VID/PID of the other
device so that the two may share data. To ensure we don't accidentally
link to a sensor from a physically separate device (if several have been
plugged in), we limit the search to siblings (i.e., devices directly
connected to the same hub).
Signed-off-by: Jason Gerecke <killertofu@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The irq_to_gpio() is old, most platforms use GENERIC_GPIO framework
and don't support this API anymore.
The i.MX6q sabrelite platform equips an egalax touchscreen controller,
and this platform already transfered to GENERIC_GPIO framework, to
support this driver, we use a more generic way to get gpio.
Add a return value checking for waking up the controller in the probe
function, this guarantee only a workable device can pass init.
[dmitry.torokhov@gmail.com: Make driver depend on CONFIG_OF as it is
now required.]
Acked-by Zhang Jiejing <jiejing.zhang@freescale.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Hui Wang <jason77.wang@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The previous implementation of qt2160_write() didn't work properly because
the value was actually not written to the device. Probably nobody detected
this because the only write that was issued was the one related to auto
calibration.
In order to fix the problem use a similar aproach as qt1070 instead.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
