Instead of using magic numbers for the registers which contain memory
addresses in the firewall table, using symbolic names.
Signed-off-by: Thierry Reding <treding@nvidia.com>
A connector's DPMS mode isn't initialized by default, therefore using a
default of 0 (DRM_MODE_DPMS_ON). This can cause problems in that the DRM
core won't explicitly turn on a connector because it thinks that it is
already on.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The VDD regulator used to be enabled only at tegra_output_hdmi_enable,
which is called after a sink is detected. However, the HDMI hotplug pin
works by returning the voltage supplied by the VDD pin, so this meant
that the hotplug pin was never asserted and the sink was not detected
unless the VDD regulator was set to be always on.
This patch moves the enable to the tegra_hdmi_init() function to make
sure the regulator will get enabled and therefore ensure proper hotplug
detection.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These seem to show up when building for architectures other than ARM,
which I guess will never happen. The reason why the kbuild test bot ran
into these was a missing dependency which has hence been fixed. Still it
doesn't hurt to fix them anyway.
Reported-by: kbuild test bot <fengguang.wu@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use EDID data to determine whether the display supports HDMI or DVI
only. The HDMI output used to assume to be connected to HDMI displays,
but that broke support for DVI displays that don't understand the
interspersed audio/other data.
To be on the safe side, default to DVI if no EDID data is available.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
[treding@nvidia.com: move detection to separate function]
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tegra114 TMDS configuration requires a new peak_current field and the
driver current override bit has changed position.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Use a structure to parameterize the code to handle differences between
the HDMI hardware on various SoC generations. This removes the need to
clutter the code with checks for individual compatible values.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Everything related to Tegra uses Tegra20 and Tegra30 instead of Tegra2
and Tegra3, respectively. Rename the TMDS arrays in the HDMI driver for
consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Since the .init() and .exit() functions are executed whenever the DRM
driver is loaded or unloaded, care must be taken not to use them for
resource allocation. Otherwise deferred probing cannot be used, since
the .init() and .exit() are not run at probe time. Similarly the code
that frees resources must be run at .remove() time. If it is run from
the .exit() function, it can release resources multiple times.
To handle this more consistently, rename the tegra_output_parse_dt()
function to tegra_output_probe() and introduce tegra_output_remove()
which can be used to free output-related resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
When the DRM driver is unloaded, all the associated resources must be
cleaned up and zeroed out. This is necessary because of the architecture
of the Tegra DRM driver, where not all subdrivers are unloaded along
with the DRM driver. Therefore device-managed managed won't be freed and
memory cannot be assumed to have been cleared (because it hasn't been
reallocated using kzalloc()) by the time the DRM driver is reloaded. It
is therefore necessary to zero out the structures to prevent strange
errors (such as slab corruptions) from occurring.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Tegra DRM driver currently uses some infrastructure to defer the DRM
core initialization until all required devices have registered. The same
infrastructure can potentially be used by any other driver that requires
more than a single sub-device of the host1x module.
Make the infrastructure more generic and keep only the DRM specific code
in the DRM part of the driver. Eventually this will make it easy to move
the DRM driver part back to the DRM subsystem.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Expose the buffer objects, syncpoint and channel functionality in the
public public header so that drivers can use them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This structure derives from host1x_client. DRM-specific fields are moved
from host1x_client to this structure, so that host1x_client can remain
agnostic of DRM.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rename the host1x_to_drm_bo() macro to host1x_to_tegra_bo() for
consistency and fixup various stylistic issues.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Other drivers use the tegra- prefix in their names, so add it to this
driver's name as well for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Rework the address table code for the host1x firewall. The previous
implementation allocated a bitfield but didn't check for a valid pointer
so it could potentially crash. Instead, embed a static bitmap within the
gr2d structure to avoid the allocation and use the Linux bitmap API to
reduce code complexity.
Don't annotate the driver's .remove() function __exit. Even if built in
the driver can be unloaded via sysfs, so .remove() needs to stick around
after initialization. Also remove the explicit initialization of the
driver's .owner field to THIS_MODULE because that's now handled by the
driver core.
Furthermore make an error message more consistent with other subdrivers,
index the syncpts array for better readability, remove a gratuituous
newline and reorder some variable declarations to make the code easier
to read.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The same code sequence is used in various places to validate a register
access in the command stream. This can be refactored into a separate
function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The value stored in this field is a pointer to a command buffer, not an
ID. Avoid some confusion by reflecting that in the field's name.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Arguments on subsequent lines should be aligned with the first argument.
This one occurrence went unnoticed during code review.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The device can be unbound from the driver via sysfs, so regardless of
whether the driver is builtin or a module, its .remove() function needs
to stick around.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The structure represents a context associated with a particular process
that has opened the Tegra DRM device and requested a channel. This is a
very DRM-specific notion and has nothing to do with host1x. Rename the
structure to more clearly mark the boundaries between the two.
Signed-off-by: Thierry Reding <treding@nvidia.com>
This structure extends drm_file with Tegra DRM specific fields and has
nothing to do with host1x. Rename the structure to more clearly mark the
boundaries between host1x and Tegra DRM.
While at it, move the structure definition out of the header. It's never
used outside of the drm.c source file, so it can be defined within that.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host1x and Tegra DRM drivers are currently tightly coupled. Renaming
the structure marks the boundary more clearly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The num_relocs count are passed to the kernel per job, not per gather.
For multi-gather jobs, we would previously fail if there were relocs in
other gathers aside from the first one.
Fix this by simply moving the check until all gathers have been
consumed.
Signed-off-by: Erik Faye-Lund <kusmabite@gmail.com>
Reviewed-by: Arto Merilainen <amerilainen@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Fix a typo (iotcl -> ioctl) in the debug message when an unknown IOCTL
is encountered.
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Thierry Reding <treding@nvidia.com>
When userspace removes the active framebuffer using DRM_IOCTL_MODE_RMFB,
or explicitly disables the CRTC (by calling drmModeSetCrtc(..., NULL)
for example), a NULL framebuffer will be passed to the .set_config()
implementation of a CRTC. The drm_crtc_helper_set_config() helper will
decide to disable a CRTC when that happens.
To do so, it calls drm_crtc_helper_disable(), which in turn will iterate
over all encoders and decouple them from their connectors and finally
call drm_helper_disable_unused_functions() to clean up and call the
.disable() or .dpms() implementation for each encoder. However, at no
point during this sequence does it track the DPMS mode of a connector,
so it will usually remain on after this.
When a connector is enabled again, drm_helper_connector_dpms() will not
notice that the DPMS mode actually changed and won't do anything, which
causes the connector to stay disabled indefinitely.
To prevent this from happening, explicitly set the connector's DPMS mode
to off when the CRTC is disabled. That way it reflects the correct state
and can be enabled again.
This solves an issue observed when terminating an X server running on
the xf86-video-modesetting driver. Without this patch, the connector
would not be enabled properly and the screen would stay dark.
Acked-by: David Airlie <airlied@linux.ie>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Just a few small fixes for radeon (audio regression fix,
stability fix, and an endian bug noticed by coverity).
* 'drm-fixes-3.12' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon/dpm: fix incompatible casting on big endian
drm/radeon: disable bapm on KB
drm/radeon: use sw CTS/N values for audio on DCE4+
device_unregister() already drops its reference to the struct device, so
explicitly calling put_device() before device_unregister() can cause the
device to have been freed before it can be unregistered.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Use a for_each_loop and add the corresponding #defines.
- Drop the _ILK postfix on the existing DE_PIPE_VBLANK macro for
consistency with everything else.
- Also use macros (and add the missing one for plane flips) for the
ivb display interrupt handler.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Drop the useless parens that Ville spotted.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Request by Ville in his review of the CRC stuff. This converts
everything but ilk_display_irq_handler since that needs a bit more
than a simple search&replace to look nice.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The bbstate contains useful bits of debugging information such as
whether the batch is being read from GTT or PPGTT, or whether it is
allowed to execute privileged instructions.
v2: Only record BB_STATE for gen4+
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
DRM_IOCTL_VERSION is a reliable way to get the driver-name and version
information. It's not related to the interface-version (SET_VERSION ioctl)
so we can safely enable it on render-nodes.
Note that gbm uses udev-BUSID to load the correct mesa driver. However,
the VERSION ioctl should be the more reliable way to do this (in case we
add new DRM-bus drivers which have no BUSID or similar).
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Similarly rename the other related functions in the power domain
interface.
Higher level driver code calling these functions knows only about power
domains, not the underlying power wells which may be different on
different platforms. Also these functions really init/cleanup/resume
power domains and only through that all related power wells, so rename
them accordingly.
Note that I left i915_{request,release}_power_well as is, since that
really changes the state only of a single power well (and is HSW
specific). It should also get a better name once we make it more
generic by controlling things through a new audio power domain.
v4:
- use intel prefix instead of i915 everywhere (Paulo)
- use a $prefix_$block_$action format (Daniel)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Originally I've thought that this is leftover hw state dirt from the
BIOS. But after way too much helpless flailing around on my part I've
noticed that the actual bug is when we change the state of an already
active pipe.
For example when we change the fdi lines from 2 to 3 without switching
off outputs in-between we'll never see the crucial on->off transition
in the ->modeset_global_resources hook the current logic relies on.
Patch version 2 got this right by instead also checking whether the
pipe is indeed active. But that in turn broke things when pipes have
been turned off through dpms since the bifurcate enabling is done in
the ->crtc_mode_set callback.
To address this issues discussed with Ville in the patch review move
the setting of the bifurcate bit into the ->crtc_enable hook. That way
we won't wreak havoc with this state when userspace puts all other
outputs into dpms off state. This also moves us forward with our
overall goal to unify the modeset and dpms on paths (which we need to
have to allow runtime pm in the dpms off state).
Unfortunately this requires us to move the bifurcate helpers around a
bit.
Also update the commit message, I've misanalyzed the bug rather badly.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=70507
Tested-by: Jan-Michael Brummer <jan.brummer@tabos.org>
Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We store cursor_x/y as int16_t internally, but the user provided
coordinates are int32_t. Clamp the coordinates so that they don't
overflow the int16_t. Since the cursor is only 64x64 in size, the
clamping can't cause any visual changes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The Intel D410PT(LW) and D425KT Mini-ITX desktop boards both show up as
having LVDS but the hardware is not populated. This patch adds them to
the list of such systems. Patch is against 3.11.4
v2: Patch revised to match the D425KT exactly as the D425KTW does have
LVDS. According to Intel's documentation, the D410PTL and D410PLTW
don't.
Signed-off-by: Rob Pearce <rob@flitspace.org.uk>
Cc: stable@vger.kernel.org
[danvet: Pimp commit message to my liking and add cc: stable.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This isn't a real fix to the problem, but rather a stopgap measure while
trying to find a proper solution.
There are several laptops out there that fail to light up the eDP panel
in UEFI boot mode. They seem to be mostly IVB machines, including but
apparently not limited to Dell XPS 13, Asus TX300, Asus UX31A, Asus
UX32VD, Acer Aspire S7. They seem to work in CSM or legacy boot.
The difference between UEFI and CSM is that the BIOS provides a
different VBT to the kernel. The UEFI VBT typically specifies 18 bpp and
1.62 GHz link for eDP, while CSM VBT has 24 bpp and 2.7 GHz link. We end
up clamping to 18 bpp in UEFI mode, which we can fit in the 1.62 Ghz
link, and for reasons yet unknown fail to light up the panel.
Dithering from 24 to 18 bpp itself seems to work; if we use 18 bpp with
2.7 GHz link, the eDP panel lights up. So essentially this is a link
speed issue, and *not* a bpp clamping issue.
The bug raised its head since
commit 657445fe86
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sat May 4 10:09:18 2013 +0200
Revert "drm/i915: revert eDP bpp clamping code changes"
which started clamping bpp *before* computing the link requirements, and
thus affecting the required bandwidth. Clamping after the computations
kept the link at 2.7 GHz.
Even though the BIOS tells us to use 18 bpp through the VBT, it happily
boots up at 24 bpp and 2.7 GHz itself! Use this information to
selectively ignore the VBT provided value.
We can't ignore the VBT eDP bpp altogether, as there are other laptops
that do require the clamping to be used due to EDID reporting higher bpp
than the panel can support.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59841
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67950
Tested-by: Ulf Winkelvos <ulf@winkelvos.de>
Tested-by: jkp <jkp@iki.fi>
CC: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On CTG+ read out the pipe bpp setting from hardware and fill it into
pipe config. Also check it appropriately.
v2: Don't do the pipe_bpp extraction inside the PCH only code block on
ILK+.
Avoid the PIPECONF read as we already have read it for the
PIPECONF_EANBLE check.
Note: This is already in drm-intel-next-queued as
commit 42571aefaf
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Fri Sep 6 23:29:00 2013 +0300
drm/i915: Add support for pipe_bpp readout
but is needed for the following bugfix.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The only real need for this field was in
i915_{request,release}_power_well, but there we can get at it by a
container_of magic. Also since in the future we'll have multiple power
wells each with its own power_well struct it makes sense to remove the
field from there where it'd be just redundancy.
Suggested-by: Paulo Zanoni <paulo.zanoni@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
